From c60a21532bc903ab86d971b478752152d4476ef8 Mon Sep 17 00:00:00 2001 From: Rosen Penev Date: Sun, 4 Feb 2018 16:24:15 -0800 Subject: ramips: Add support for the GnuBee Personal Cloud Two The GnuBee Personal Cloud Two crowdfunded on https://www.crowdsupply.com It is a low-cost, low-power, network-attached storage device. Specifications: - SoC: MediaTek MT7621AT - RAM: DDR3 512 MB - Flash: 32 MB - Six SATA ports for 3.5" Drives - One SDcard - One USB 3.0 - Two USB 2.0 - Gigabit Ethernet: Three Ports - UART 3.5mm Audio Jack or 3 pin header - 57600 8N1 - Three GPIOs available on a pin header Flash instructions: The GnuBee Personal Cloud Two ships with libreCMC installed. libreCMC is a Free Software Foundation approved fork of LEDE/OpenWrt. As such one can upgrade using the webinterface or sysupgrade. Das U-Boot has multiple options for recovery or updates including : - USB - http - tftp Errata: - While there are three ethernet ports, the third requires support for the second GMAC. This will come in kernel 4.14. - The first hard drive slot has a clearance issue with the two fan headers. Workaround is to pull the headers out and connect the pins to jumper wires. - Using this device as a NAS is problematic with the 4.9 kernel as many /dev/sdX reads throw silent errors. The current theory behind this is some kind of unhandled DMA mapping error in the kernel. This is not an issue with kernel 4.4. Signed-off-by: L. D. Pinney Signed-off-by: Rosen Penev --- target/linux/ramips/base-files/etc/board.d/01_leds | 6 ++++++ target/linux/ramips/base-files/etc/board.d/02_network | 4 ++++ target/linux/ramips/base-files/etc/diag.sh | 1 + 3 files changed, 11 insertions(+) (limited to 'target/linux/ramips/base-files/etc') diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds index 677bf95a27..573dd31c64 100755 --- a/target/linux/ramips/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/base-files/etc/board.d/01_leds @@ -191,6 +191,12 @@ gb-pc1) ucidef_set_led_switch "lan1" "lan1" "$boardname:green:lan1" "switch0" "0x01" ucidef_set_led_switch "lan2" "lan2" "$boardname:green:lan2" "switch0" "0x10" ;; +gb-pc2) + ucidef_set_led_switch "lan" "lan" "$board:green:lan" "switch0" "0x01" + ucidef_set_led_switch "wan" "wan" "$board:green:wan" "switch0" "0x10" + ucidef_set_led_netdev "eth1-g" "eth1-g" "$board:green:eth1-g" "eth1" + ucidef_set_led_netdev "eth1-y" "eth1-y" "$board:green:eth1-y" "eth1" + ;; gl-mt300a|\ gl-mt300n|\ gl-mt750) diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index d064bfef3b..1ccff892b1 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -206,6 +206,10 @@ ramips_setup_interfaces() ucidef_add_switch "switch0" \ "0:lan" "4:lan" "6@eth0" ;; + gb-pc2) + ucidef_add_switch "switch0" \ + "4:lan" "0:wan" "6@eth0" + ;; gl-mt300n-v2) ucidef_add_switch "switch0" \ "1:lan" "0:wan" "6@eth0" diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh index 6b11fb2872..e38311d5e5 100644 --- a/target/linux/ramips/base-files/etc/diag.sh +++ b/target/linux/ramips/base-files/etc/diag.sh @@ -91,6 +91,7 @@ get_status_led() { dir-620-d1|\ dwr-512-b|\ gb-pc1|\ + gb-pc2|\ hpm|\ hw550-3g|\ mac1200rv2|\ -- cgit v1.2.3