From 37af596593b0e84d0a076ab8f173066e3d7bc810 Mon Sep 17 00:00:00 2001 From: Cezary Jackiewicz Date: Thu, 19 Apr 2018 19:34:22 +0200 Subject: ramips: add support for D-Link DWR-118-A2 The DWR-118-A2 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 128 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7612EN) - 4x 10/100 Mbps Ethernet (1 WAN and 3 LAN) - 1x 10/100/1000 Mbps Marvell Ethernet PHY (1 LAN) - 2x external, non-detachable antennas - 1x USB 2.0 - UART (J1) header on PCB (57600 8n1) - 7x LED (5x GPIO-controlled), 2x button - JBOOT bootloader Known issues: - GELAN not working - flash is very slow The status led has been assigned to the dwr-118-a2:green:internet led. At the end of the boot it is switched off and is available for other operation. Work correctly also during sysupgrade operation. Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Cezary Jackiewicz Signed-off-by: Pawel Dembicki --- target/linux/ramips/base-files/etc/board.d/01_leds | 7 +++++++ target/linux/ramips/base-files/etc/board.d/02_network | 5 +++++ 2 files changed, 12 insertions(+) (limited to 'target/linux/ramips/base-files/etc/board.d') diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds index 4e90efd4e6..44511bb0f6 100755 --- a/target/linux/ramips/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/base-files/etc/board.d/01_leds @@ -162,6 +162,13 @@ dlink,dwr-116-a1|\ mzk-ex300np) set_wifi_led "$boardname:green:wifi" ;; +dlink,dwr-118-a2) + ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x0e" + ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x01" + set_wifi_led "$boardname:green:wlan2g" "wlan1" + set_usb_led "$boardname:green:usb" + ucidef_set_led_default "internet" "internet" "$boardname:green:internet" "0" + ;; dlink,dwr-921-c1) set_wifi_led "$boardname:green:wifi" ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x0f" diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index 915c3584c5..b6f70ef50d 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -157,6 +157,10 @@ ramips_setup_interfaces() wrh-300cr) ucidef_set_interface_lan "eth0" ;; + dlink,dwr-118-a2) + ucidef_add_switch "switch0" \ + "1:lan:2" "2:lan:1" "3:lan:3" "4:lan" "0:wan" "6@eth0" + ;; mir3g) ucidef_add_switch "switch0" \ "2:lan:2" "3:lan:1" "1:wan" "6t@eth0" @@ -462,6 +466,7 @@ ramips_setup_macs() wan_mac=$(mtd_get_mac_ascii factory wanmac) ;; dlink,dwr-116-a1|\ + dlink,dwr-118-a2|\ dlink,dwr-921-c1) wan_mac=$(jboot_config_read -m -i $(find_mtd_part "config") -o 0xE000) lan_mac=$(macaddr_add "$wan_mac" 1) -- cgit v1.2.3