From 27b2f0fc0fc5513304a5be3c5b8cb23aeb09e6f5 Mon Sep 17 00:00:00 2001 From: Ademar Arvati Filho Date: Fri, 6 Jul 2018 00:56:58 +0000 Subject: kirkwood: add support for Iomega Storcenter ix2-200 Iomega Storcenter ix2-200 is a dual SATA NAS powered by a Marvell Kirkwood SoC clocked at 1GHz. It has 256MB of RAM and 32MB of flash memory, 3x USB 2.0 and 1x 1Gbit/s NIC Specification: - SoC: Marvell Kirkwood 88F6281 - CPU/Speed: 1000Mhz - Flash-Chip: Hynix NAND - Flash size: 32 MiB,erase size:16 KiB,page size:512,OOB size:16 - RAM: 256MB - LAN: 1x 1000 Mbps Ethernet - WiFi: none - 3x USB 2.0 - UART: for serial console Installation instructions - easy steps: 1. download factory.bin and copy into tftp server 2. access uboot environment with serial cable and run ``` setenv mainlineLinux yes setenv arcNumber 1682 setenv console 'console=ttyS0,115200n8' setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)' setenv bootargs_root 'root=' setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000' saveenv setenv serverip 192.168.1.1 setenv ipaddr 192.168.1.13 tftpboot 0x00800000 factory.bin nand erase 0x100000 $(filesize) nand write 0x00800000 0x100000 $(filesize) run bootcmd ``` 3. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13) Installation steps nand bad blocks proof: 1. download initramfs-uImage and copy into usb ext2 partition ``` mkfs.ext2 -L ext2 /dev/sdh1 mount -t ext2 /dev/sdh1 /mnt cp initramfs-uImage /mnt/initramfs.bin umount /mnt ``` 2. access uboot environment with serial cable and run ``` setenv mainlineLinux yes setenv arcNumber 1682 setenv console 'console=ttyS0,115200n8' setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)' setenv bootargs_root 'root=' setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000' saveenv usb reset; ext2load usb 0:1 0x00800000 /initramfs.bin; bootm 0x00800000 ``` 3. log into openwrt and sysupgrade to install into flash ``` sysupgrade -n /tmp/sysupgrade.bin ``` 4. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13) Signed-off-by: Ademar Arvati Filho --- target/linux/kirkwood/image/Makefile | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) (limited to 'target/linux/kirkwood/image/Makefile') diff --git a/target/linux/kirkwood/image/Makefile b/target/linux/kirkwood/image/Makefile index fdf86099bc..84e749f494 100644 --- a/target/linux/kirkwood/image/Makefile +++ b/target/linux/kirkwood/image/Makefile @@ -62,6 +62,22 @@ define Device/iom_iconnect-1.1 endef TARGET_DEVICES += iom_iconnect-1.1 +define Device/iom_ix2_200 + DEVICE_TITLE := Iomega StorCenter ix2-200 + DEVICE_DTS := kirkwood-iomega_ix2_200 + DEVICE_PACKAGES += kmod-gpio-button-hotplug kmod-i2c-mv64xxx kmod-hwmon-lm63 + DEVICE_TYPE:=nas + PAGESIZE := 512 + SUBPAGESIZE := 256 + BLOCKSIZE := 16KiB + KERNEL_SIZE := 3072k + KERNEL_IN_UBI := 0 + UBINIZE_OPTS := -E 5 + IMAGE_SIZE := 32505856 + IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | check-size $$$$(IMAGE_SIZE) +endef +TARGET_DEVICES += iom_ix2_200 + define Device/linksys_audi DEVICE_TITLE := Linksys EA3500 (Audi) DEVICE_PACKAGES := kmod-mwl8k swconfig wpad-mini kmod-gpio-button-hotplug -- cgit v1.2.3