From 4e46beb31342a2b02e32185e91806093f68a77be Mon Sep 17 00:00:00 2001 From: Jan Alexander Date: Mon, 30 Nov 2020 11:51:16 +0100 Subject: ipq806x: add support for Ubiquiti UniFi AC HD Hardware -------- SoC: Qualcomm IPQ8064 RAM: 512MB DDR3 Flash: 256MB NAND (Micron MT29F2G08ABBEAH4) 32MB SPI-NOR (Macronix MX25U25635F) WLAN: Qualcomm Atheros QCA9994 4T4R b/g/n Qualcomm Atheros QCA9994 4T4R a/n/ac ETH: eth0 - SECONDARY (Atheros AR8033) eth1 - MAIN (Atheros AR8033) USB: USB-C LED: Dome (white / blue) BTN: Reset Installation ------------ Copy the OpenWrt sysupgrade image to the /tmp directory of the device using scp. Default IP address is 192.168.1.20 and default username and password are "ubnt". SSH to the device and write the bootselect flag to ensure it is booting from the mtd partition the OpenWrt image will be written to. Verify the output device below matches mtd partition "bootselect" using /proc/mtd. > dd if=/dev/zero bs=1 count=1 seek=7 conv=notrunc of=/dev/mtd11 Write the OpenWrt sysupgrade image to the mtd partition labeled "kernel0". Also verify the used partition device using /proc/mtd. > dd if=/tmp/sysupgrade.bin of=/dev/mtdblock12 Reboot the device. Back to stock ------------- Use the TFTP recovery procedure with the Ubiquiti firmware image to restore the vendor firmware. Signed-off-by: Jan Alexander --- target/linux/ipq806x/base-files/etc/board.d/02_network | 3 +++ .../ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac | 8 ++++++++ 2 files changed, 11 insertions(+) (limited to 'target/linux/ipq806x/base-files/etc') diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network index fbf56c5e0c..ddef4b7ac6 100755 --- a/target/linux/ipq806x/base-files/etc/board.d/02_network +++ b/target/linux/ipq806x/base-files/etc/board.d/02_network @@ -66,6 +66,9 @@ qcom,ipq8064-db149) ucidef_add_switch "switch0" \ "1:lan" "2:lan" "3:lan" "4:lan" "6u@eth1" "5:wan" "0u@eth0" ;; +ubnt,unifi-ac-hd) + ucidef_set_interface_lan "eth0 eth1" + ;; zyxel,nbg6817) hw_mac_addr=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr) ucidef_add_switch "switch0" \ diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac index f0256fd259..5af3a5b805 100644 --- a/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac +++ b/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac @@ -9,6 +9,14 @@ PHYNBR=${DEVPATH##*/phy} . /lib/functions.sh . /lib/functions/system.sh +board=$(board_name) + +case "$board" in + ubnt,unifi-ac-hd) + macaddr_add $(mtd_get_mac_binary EEPROM 0x6) $(($PHYNBR + 1)) > /sys${DEVPATH}/macaddress + ;; +esac + OPATH=${DEVPATH##/devices/platform/} OPATH=${OPATH%%/ieee*} -- cgit v1.2.3