From d3c88811942a9dc9bbb01ca0443ae9cd790d1988 Mon Sep 17 00:00:00 2001 From: Stefan Schake Date: Fri, 2 Oct 2020 14:32:55 +0200 Subject: ipq40xx: add support for devolo Magic 2 WiFi next SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v71) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8075 (2 ports) PLC: MaxLinear G.hn 88LX5152 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET, WiFi, PLC Button LEDS: red/white home, white WiFi To modify a retail device to run OpenWRT firmware: 1) Setup a TFTP server on IP address 192.168.0.100 and copy the OpenWRT initramfs (initramfs-fit-uImage.itb) to the TFTP root as 'uploadfile'. 2) Power on the device while pressing the recessed reset button next to the Ethernet ports. This causes the bootloader to retrieve and start the initramfs. 3) Once the initramfs is booted, the device will come up with IP 192.168.1.1. You can then connect through SSH (allow some time for the first connection). 4) On the device shell, run 'fw_printenv' to show the U-boot environment. Backup this information since it contains device unique factory data. 5) Change the boot command to support booting OpenWRT: # fw_setenv bootcmd 'sf probe && sf read 0x84000000 0x180000 0x400000 && bootm' 6) Change directory to /tmp, download the sysupgrade (e.g. through wget) and install it with sysupgrade. The device will reboot into OpenWRT. Notice that there is currently no support for booting the G.hn chip. This requires userland software we lack the rights to share right now. Signed-off-by: Stefan Schake --- .../ipq40xx/base-files/etc/board.d/02_network | 7 + .../etc/hotplug.d/firmware/11-ath10k-caldata | 8 + .../lib/preinit/06_set_preinit_iface_ipq40xx.sh | 3 + .../boot/dts/qcom-ipq4018-magic-2-wifi-next.dts | 268 +++++++++++++++++++++ target/linux/ipq40xx/image/Makefile | 19 ++ .../patches-5.4/901-arm-boot-add-dts-files.patch | 3 +- 6 files changed, 307 insertions(+), 1 deletion(-) create mode 100644 target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-magic-2-wifi-next.dts (limited to 'target/linux/ipq40xx') diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 4361b7c395..07bacaf51b 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -84,6 +84,9 @@ ipq40xx_setup_interfaces() ucidef_add_switch "switch0" \ "0u@eth0" "3:lan" "4:lan" ;; + devolo,magic-2-wifi-next) + ucidef_set_interface_lan "eth0 eth1 eth2" + ;; ezviz,cs-w3-wd1200g-eup) ucidef_set_interfaces_lan_wan "eth0" "eth1" ucidef_add_switch "switch0" \ @@ -137,6 +140,10 @@ ipq40xx_setup_macs() cilab,meshpoint-one) label_mac=$(mtd_get_mac_binary "ART" 0x1006) ;; + devolo,magic-2-wifi-next) + lan_mac=$(mtd_get_mac_ascii APPSBLENV MacAddress0) + label_mac=$lan_mac + ;; dlink,dap-2610) lan_mac=$(mtd_get_mac_ascii bdcfg lanmac) label_mac=$lan_mac diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index e50732586a..7293438dfa 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -109,6 +109,10 @@ case "$FIRMWARE" in unielec,u4019-32m) caldata_extract "0:ART" 0x1000 0x2f20 ;; + devolo,magic-2-wifi-next) + caldata_extract "ART" 0x1000 0x2f20 + ath10k_patch_mac $(mtd_get_mac_ascii APPSBLENV WiFiMacAddress0) + ;; dlink,dap-2610) caldata_extract "ART" 0x1000 0x2f20 ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac) @@ -208,6 +212,10 @@ case "$FIRMWARE" in unielec,u4019-32m) caldata_extract "0:ART" 0x5000 0x2f20 ;; + devolo,magic-2-wifi-next) + caldata_extract "ART" 0x5000 0x2f20 + ath10k_patch_mac $(mtd_get_mac_ascii APPSBLENV WiFiMacAddress1) + ;; dlink,dap-2610) caldata_extract "ART" 0x5000 0x2f20 ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac_a) diff --git a/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh b/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh index 0311922f08..e97133f105 100644 --- a/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh +++ b/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh @@ -13,6 +13,9 @@ set_preinit_iface() { zyxel,nbg6617) ifname=eth0 ;; + devolo,magic-2-wifi-next) + ifname=eth1 + ;; esac } diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-magic-2-wifi-next.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-magic-2-wifi-next.dts new file mode 100644 index 0000000000..2709aef502 --- /dev/null +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-magic-2-wifi-next.dts @@ -0,0 +1,268 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq4019.dtsi" +#include +#include + +/ { + model = "devolo Magic 2 WiFi next"; + compatible = "devolo,magic-2-wifi-next"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; + }; + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + reset-gpios = <&tlmm 59 GPIO_ACTIVE_LOW>; + reset-delay-us = <2000>; + + /delete-node/ ethernet-phy@0; + /delete-node/ ethernet-phy@1; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + switch_lan_bmp = <0x3e>; + switch_wan_bmp = <0x0>; + }; + + edma@c080000 { + status = "okay"; + qcom,num_gmac = <3>; + + gmac0 { + qcom,phy_mdio_addr = <3>; + qcom,poll_required = <1>; + /delete-property/ qcom,forced_speed; + /delete-property/ qcom,forced_duplex; + vlan_tag = <1 0x10>; + }; + + gmac1 { + qcom,phy_mdio_addr = <2>; + qcom,poll_required = <1>; + /delete-property/ qcom,forced_speed; + /delete-property/ qcom,forced_duplex; + vlan_tag = <1 0x08>; + }; + + gmac2 { + local-mac-address = [00 00 00 00 00 00]; + qcom,phy_mdio_addr = <4>; + qcom,poll_required = <1>; + /delete-property/ qcom,forced_speed; + /delete-property/ qcom,forced_duplex; + vlan_tag = <1 0x20>; + }; + }; + + gpio_export { + compatible = "gpio-export"; + #size-cells = <0>; + + plc { + gpio-export,name = "plc-enable"; + gpio-export,output = <1>; + gpios = <&tlmm 63 GPIO_ACTIVE_HIGH>; + }; + }; + + }; + + keys { + compatible = "gpio-keys"; + + wlan { + label = "WLAN"; + gpios = <&tlmm 5 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + reset { + label = "Reset"; + gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + status_dlan { + label = "white:dlan"; + gpios = <&tlmm 4 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + + status_wlan { + label = "white:wlan"; + gpios = <&tlmm 58 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + + error_dlan { + label = "red:dlan"; + gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + }; +}; + +&tlmm { + spi_0_pins: spi_0_pinmux { + mux { + function = "blsp_spi0"; + pins = "gpio55", "gpio56", "gpio57"; + drive-strength = <12>; + bias-disable; + }; + + mux_cs { + function = "gpio"; + pins = "gpio54"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; + + mdio_pins: mdio_pinmux { + mux_1 { + pins = "gpio53"; + function = "mdio"; + bias-pull-up; + }; + mux_2 { + pins = "gpio52"; + function = "mdc"; + bias-pull-up; + }; + }; + + serial_pins: serial_pinmux { + mux { + pins = "gpio61", "gpio60"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + button_pins: button_pinmux { + mux { + function = "gpio"; + pins = "gpio0", "gpio5"; + bias-disable; + input; + }; + }; +}; + +&cryptobam { + status = "okay"; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "devolo,magic-2-wifi-next"; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "devolo,magic-2-wifi-next"; +}; + +&blsp1_spi1 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + linux,modalias = "n25q128a11"; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "SBL1"; + reg = <0x00000000 0x00040000>; + read-only; + }; + partition@40000 { + label = "MIBIB"; + reg = <0x00040000 0x00020000>; + read-only; + }; + partition@60000 { + label = "QSEE"; + reg = <0x00060000 0x00060000>; + read-only; + }; + partition@c0000 { + label = "CDT"; + reg = <0x000c0000 0x00010000>; + read-only; + }; + partition@d0000 { + label = "DDRPARAMS"; + reg = <0x000d0000 0x00010000>; + read-only; + }; + partition@e0000 { + label = "APPSBLENV"; /* uboot env*/ + reg = <0x000e0000 0x00010000>; + }; + partition@f0000 { + label = "APPSBL"; /* uboot */ + reg = <0x000f0000 0x00080000>; + read-only; + }; + partition@170000 { + label = "ART"; + reg = <0x00170000 0x00010000>; + read-only; + }; + firmware@180000 { + compatible = "denx,fit"; + label = "firmware"; + reg = <0x00180000 0x01a80000>; + }; + }; + }; +}; diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index 86bf5a2ccb..487f3b5638 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -317,6 +317,25 @@ define Device/compex_wpj428 endef TARGET_DEVICES += compex_wpj428 +define Device/devolo_magic-2-wifi-next + $(call Device/FitImage) + DEVICE_VENDOR := devolo + DEVICE_MODEL := Magic 2 WiFi next + SOC := qcom-ipq4018 + KERNEL_SIZE := 4096k + + # If the bootloader sees 0xDEADC0DE and this trailer at the 64k boundary of a TFTP image + # it will bootm it, just like we want for the initramfs. + KERNEL_INITRAMFS := kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to 64k |\ + append-string -e '\xDE\xAD\xC0\xDE{"fl_initramfs":""}\x00' + + IMAGE_SIZE := 26624k + IMAGES := sysupgrade.bin + IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata + DEVICE_PACKAGES := ipq-wifi-devolo_magic-2-wifi-next uboot-envtools +endef +TARGET_DEVICES += devolo_magic-2-wifi-next + define Device/dlink_dap-2610 $(call Device/FitImageLzma) DEVICE_VENDOR := D-Link diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch index c4502aa3f7..d470bb7204 100644 --- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -837,11 +837,56 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -837,11 +837,57 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -18,6 +18,7 @@ Signed-off-by: John Crispin + qcom-ipq4018-ap120c-ac.dtb \ + qcom-ipq4018-dap-2610.dtb \ + qcom-ipq4018-cs-w3-wd1200g-eup.dtb \ ++ qcom-ipq4018-magic-2-wifi-next.dtb \ + qcom-ipq4018-ea6350v3.dtb \ + qcom-ipq4018-eap1300.dtb \ + qcom-ipq4018-ecw5211.dtb \ -- cgit v1.2.3