From 6f6c00cfc95f603a533ff142cc0e1d34a4ab0588 Mon Sep 17 00:00:00 2001 From: Kristian Evensen Date: Sun, 20 Oct 2019 11:33:13 +0200 Subject: ipq40xx: Add support for Unielec U4019 This commit adds support for the 32MB storage/512MB RAM version of the U4019 IPQ4019-based board from Unielec. The board has the following specifications: * Qualcomm IPQ4019 (running at 717MHz) * 512MB DDR3 RAM (optional 256MB/1GB) * 32MB SPI NOR (optional 8/16MB or NAND) * Five gigabit ports (Qualcomm QCA8075) * 1x 2.4 GHz wifi (QCA4019 hw1.0) * 1x 5 Ghz wifi (QCA4019 hw1.0) * 1x mini-PCIe slot (only USB-pins connected) * 1x SIM slot (mini-SIM) * 1x USB2.0 port * 1x button * 1x controllable LED * 1x micro SD-card reader Working: * Ethernet * Wifi * USB-port * mini-PCIe slot + SIM slot * Button * Sysupgrade Not working: * SD card slot (no upstream support) Installation instructions: In order to install OpenWRT on the U4019, you need to go via the initramfs-image. The installation steps are as follows: * Connect to board via serial (header exposed and clearly marked). * Interrupt bootloader by pressing a button. * Copy the initramfs-image to your tftp folder, call the file C0A80079.img. * Give the network interface connected to the U4019 the address 192.168.0.156/24. * Start your tftp-server and run tftpboot on the board. * Run bootm when the file has been transferred, to boot OpenWRT. * Once OpenWRT has booted, copy the sysupgrade-image to the device and run sysupgrade to install OpenWRT on the U4019. Notes: - Since IPQ4019 has been moved to 4.19, I have not added support for kernel 4.14. - There is a bug with hardware encryption on IPQ4019, causing poor performance with TCP and ipsec (see for example FS#2355). In order to improve performance, I have disabled hardware encryption in the DTS. We can enable hw. enc. once/if bug is fixed. - In order for Ethernet to work, the phy has to be reset by setting gpio 47 low/high. Adding support for phy reset via gpio required patching the mdio-driver, and the code added comes from the vendor driver. I do not know if patching the driver is an acceptable approach or not. v1->v2: * Do not use wildcard as identifier in the board.d-scripts (thanks Adrian Schmutzler). Signed-off-by: Kristian Evensen --- .../ipq40xx/base-files/etc/board.d/02_network | 5 + .../etc/hotplug.d/firmware/11-ath10k-caldata | 6 +- .../boot/dts/qcom-ipq4019-unielec-u4019-32m.dts | 79 ++++++++ .../arm/boot/dts/qcom-ipq4019-unielec-u4019.dtsi | 223 +++++++++++++++++++++ target/linux/ipq40xx/image/Makefile | 13 ++ .../patches-4.19/700-net-add-qualcomm-mdio.patch | 80 +++++++- .../patches-4.19/901-arm-boot-add-dts-files.patch | 15 +- 7 files changed, 410 insertions(+), 11 deletions(-) create mode 100644 target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-unielec-u4019-32m.dts create mode 100644 target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-unielec-u4019.dtsi (limited to 'target/linux/ipq40xx') diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index e5ba7260f3..f036dc842f 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -61,6 +61,11 @@ ipq40xx_setup_interfaces() ucidef_add_switch "switch0" \ "0u@eth0" "3:lan" "4:lan" "0u@eth1" "5:wan" ;; + unielec,u4019-32m) + ucidef_set_interfaces_lan_wan "eth0" "eth1" + ucidef_add_switch "switch0" \ + "0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "0u@eth1" "5:wan" + ;; *) echo "Unsupported hardware. Network interfaces not initialized" ;; diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index bdb12b2921..7a9cf6873e 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -74,7 +74,8 @@ case "$FIRMWARE" in openmesh,a42 |\ openmesh,a62 |\ qxwlan,e2600ac-c1 |\ - qxwlan,e2600ac-c2) + qxwlan,e2600ac-c2 |\ + unielec,u4019-32m) caldata_extract "0:ART" 0x1000 0x2f20 ;; engenius,ens620ext) @@ -135,7 +136,8 @@ case "$FIRMWARE" in openmesh,a42 |\ openmesh,a62 |\ qxwlan,e2600ac-c1 |\ - qxwlan,e2600ac-c2) + qxwlan,e2600ac-c2 | + unielec,u4019-32m) caldata_extract "0:ART" 0x5000 0x2f20 ;; engenius,ens620ext) diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-unielec-u4019-32m.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-unielec-u4019-32m.dts new file mode 100644 index 0000000000..606ac165ba --- /dev/null +++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-unielec-u4019-32m.dts @@ -0,0 +1,79 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/dts-v1/; + +#include "qcom-ipq4019-unielec-u4019.dtsi" +#include +#include + +/ { + model = "Unielec U4019 (32M)"; + compatible = "unielec,u4019-32m","unielec,u4019","qcom,ipq4019"; +}; + +&blsp1_spi1 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>; + + flash@0 { + reg = <0>; + compatible = "jedec,spi-nor"; + spi-max-frequency = <24000000>; + broken-flash-reset; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:SBL1"; + reg = <0x0 0x40000>; + read-only; + }; + partition@40000 { + label = "0:MIBIB"; + reg = <0x40000 0x20000>; + read-only; + }; + partition@60000 { + label = "0:QSEE"; + reg = <0x60000 0x60000>; + read-only; + }; + partition@c0000 { + label = "0:CDT"; + reg = <0xc0000 0x10000>; + read-only; + }; + partition@d0000 { + label = "0:DDRPARAMS"; + reg = <0xd0000 0x10000>; + read-only; + }; + partition@e0000 { + label = "0:APPSBLENV"; + reg = <0xe0000 0x10000>; + read-only; + }; + partition@f0000 { + label = "0:APPSBL"; + reg = <0xf0000 0x80000>; + read-only; + }; + partition@170000 { + label = "0:ART"; + reg = <0x170000 0x10000>; + read-only; + }; + partition@180000 { + compatible = "denx,fit"; + label = "firmware"; + reg = <0x180000 0x1e80000>; + }; + }; + }; +}; + diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-unielec-u4019.dtsi b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-unielec-u4019.dtsi new file mode 100644 index 0000000000..cf67fddd2b --- /dev/null +++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-unielec-u4019.dtsi @@ -0,0 +1,223 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + compatible = "unielec,u4019","qcom,ipq4019"; + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + phy-reset-gpio = <&tlmm 47 0>; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + status = "okay"; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + usb2@60f8800 { + status = "okay"; + + dwc3@6000000 { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; + }; + }; + + usb3@8af8800 { + status = "okay"; + + dwc3@8a00000 { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; + + port@2 { + reg = <2>; + #trigger-source-cells = <0>; + }; + }; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + + aliases { + led-boot = &led_status; + led-failsafe = &led_status; + led-running = &led_status; + led-upgrade = &led_status; + serial0 = &blsp1_uart1; + serial1 = &blsp1_uart2; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + led_status: led2 { + label = "u4019:green:led2"; + gpios = <&tlmm 68 GPIO_ACTIVE_LOW>; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_0_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&blsp1_uart2 { + pinctrl-0 = <&serial_1_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&qpic_bam { + status = "okay"; +}; + +&tlmm { + mdio_pins: mdio_pinmux { + mux_1 { + pins = "gpio6"; + function = "mdio"; + bias-pull-up; + }; + mux_2 { + pins = "gpio7"; + function = "mdc"; + bias-pull-up; + }; + }; + + serial_0_pins: serial0-pinmux { + mux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + }; + serial_1_pins: serial1_pinmux { + mux { + pins = "gpio8", "gpio9"; + function = "blsp_uart1"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pinmux { + function = "blsp_spi0"; + pins = "gpio13", "gpio14", "gpio15"; + drive-strength = <12>; + bias-disable; + }; + + pinmux_cs { + function = "gpio"; + pins = "gpio12"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; + + led_pins: led_pinmux { + mux { + function = "gpio"; + pins = "gpio68"; + bias-disabled; + output-low; + }; + }; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&wifi0 { + status = "okay"; +}; + +&wifi1 { + status = "okay"; +}; diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index 4572ab461d..8907eb756b 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -404,6 +404,19 @@ define Device/qxwlan_e2600ac-c2 endef TARGET_DEVICES += qxwlan_e2600ac-c2 +define Device/unielec_u4019-32m + $(call Device/FitImage) + DEVICE_VENDOR := Unielec + DEVICE_MODEL := U4019 (32M) + BOARD_NAME := u4019-32m + DEVICE_DTS := qcom-ipq4019-unielec-u4019-32m + KERNEL_SIZE := 4096k + IMAGE_SIZE := 31232k + IMAGES := sysupgrade.bin + IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata +endef +TARGET_DEVICES += unielec_u4019-32m + define Device/zyxel_nbg6617 $(call Device/FitImageLzma) DEVICE_VENDOR := ZyXEL diff --git a/target/linux/ipq40xx/patches-4.19/700-net-add-qualcomm-mdio.patch b/target/linux/ipq40xx/patches-4.19/700-net-add-qualcomm-mdio.patch index e939597b8e..4be25186e6 100644 --- a/target/linux/ipq40xx/patches-4.19/700-net-add-qualcomm-mdio.patch +++ b/target/linux/ipq40xx/patches-4.19/700-net-add-qualcomm-mdio.patch @@ -1,6 +1,20 @@ +From 234d6f40fb4b771b396b45a9492aab463771bd0b Mon Sep 17 00:00:00 2001 +From: Kristian Evensen +Date: Tue, 6 Aug 2019 11:42:57 +0200 +Subject: [PATCH] phy: Add ipq40xx mdio driver + +--- + drivers/net/phy/Kconfig | 7 + + drivers/net/phy/Makefile | 1 + + drivers/net/phy/mdio-ipq40xx.c | 247 +++++++++++++++++++++++++++++++++ + 3 files changed, 255 insertions(+) + create mode 100644 drivers/net/phy/mdio-ipq40xx.c + +diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig +index 1f5fd24cd..eb71b47a3 100644 --- a/drivers/net/phy/Kconfig +++ b/drivers/net/phy/Kconfig -@@ -519,6 +519,13 @@ config XILINX_GMII2RGMII +@@ -436,6 +436,13 @@ config XILINX_GMII2RGMII the Reduced Gigabit Media Independent Interface(RGMII) between Ethernet physical media devices and the Gigabit Ethernet controller. @@ -14,9 +28,11 @@ endif # PHYLIB config MICREL_KS8995MA +diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile +index f21cda9d8..804c52634 100644 --- a/drivers/net/phy/Makefile +++ b/drivers/net/phy/Makefile -@@ -48,6 +48,7 @@ obj-$(CONFIG_MDIO_CAVIUM) += mdio-cavium +@@ -33,6 +33,7 @@ obj-$(CONFIG_MDIO_CAVIUM) += mdio-cavium.o obj-$(CONFIG_MDIO_GPIO) += mdio-gpio.o obj-$(CONFIG_MDIO_HISI_FEMAC) += mdio-hisi-femac.o obj-$(CONFIG_MDIO_I2C) += mdio-i2c.o @@ -24,9 +40,12 @@ obj-$(CONFIG_MDIO_MOXART) += mdio-moxart.o obj-$(CONFIG_MDIO_MSCC_MIIM) += mdio-mscc-miim.o obj-$(CONFIG_MDIO_OCTEON) += mdio-octeon.o +diff --git a/drivers/net/phy/mdio-ipq40xx.c b/drivers/net/phy/mdio-ipq40xx.c +new file mode 100644 +index 000000000..88fe5dc2b --- /dev/null +++ b/drivers/net/phy/mdio-ipq40xx.c -@@ -0,0 +1,196 @@ +@@ -0,0 +1,247 @@ +/* + * Copyright (c) 2015-2016, The Linux Foundation. All rights reserved. + * @@ -49,8 +68,10 @@ +#include +#include +#include ++#include +#include +#include ++#include + +#define MDIO_CTRL_0_REG 0x40 +#define MDIO_CTRL_1_REG 0x44 @@ -150,11 +171,60 @@ + return 0; +} + ++static int ipq40xx_phy_reset(struct platform_device *pdev) ++{ ++ struct device_node *mdio_node; ++ int phy_reset_gpio_number; ++ int ret; ++ ++ mdio_node = of_find_node_by_name(NULL, "mdio"); ++ if (!mdio_node) { ++ dev_err(&pdev->dev, "Could not find mdio node\n"); ++ return -ENOENT; ++ } ++ ++ ret = of_get_named_gpio(mdio_node, "phy-reset-gpio", 0); ++ if (ret < 0) { ++ dev_err(&pdev->dev, "Could not find phy-reset-gpio\n"); ++ return ret; ++ } ++ ++ phy_reset_gpio_number = ret; ++ ++ ret = gpio_request(phy_reset_gpio_number, "phy-reset-gpio"); ++ if (ret) { ++ dev_err(&pdev->dev, "Can't get phy-reset-gpio %d\n", ret); ++ return ret; ++ } ++ ++ ret = gpio_direction_output(phy_reset_gpio_number, 0x0); ++ if (ret) { ++ dev_err(&pdev->dev, ++ "Can't set direction for phy-reset-gpio %d\n", ret); ++ goto phy_reset_out; ++ } ++ ++ usleep_range(1000, 10005); ++ ++ gpio_set_value(phy_reset_gpio_number, 0x01); ++ ++phy_reset_out: ++ gpio_free(phy_reset_gpio_number); ++ ++ return ret; ++} ++ +static int ipq40xx_mdio_probe(struct platform_device *pdev) +{ + struct ipq40xx_mdio_data *am; + struct resource *res; -+ int i; ++ int i, ret; ++ ++ ret = ipq40xx_phy_reset(pdev); ++ if (ret) { ++ dev_err(&pdev->dev, "Could not find qca8075 reset gpio\n"); ++ return -ENODEV; ++ } + + am = devm_kzalloc(&pdev->dev, sizeof(*am), GFP_KERNEL); + if (!am) @@ -223,3 +293,5 @@ +MODULE_AUTHOR("Qualcomm Atheros"); +MODULE_VERSION(DRV_VERSION); +MODULE_LICENSE("Dual BSD/GPL"); +-- +2.20.1 diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch index a0386f6b66..aa4c0f2e6f 100644 --- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch @@ -1,16 +1,18 @@ -From 8f68331e14dff9a101f2d0e1d6bec84a031f27ee Mon Sep 17 00:00:00 2001 +From a10fab12a927e60b7141a602e740d70cb4d09e4a Mon Sep 17 00:00:00 2001 From: John Crispin Date: Thu, 9 Mar 2017 11:03:18 +0100 -Subject: [PATCH 69/69] arm: boot: add dts files +Subject: [PATCH] arm: boot: add dts files Signed-off-by: John Crispin --- - arch/arm/boot/dts/Makefile | 8 ++++++++ - 1 file changed, 8 insertions(+) + arch/arm/boot/dts/Makefile | 23 +++++++++++++++++++++++ + 1 file changed, 23 insertions(+) +diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile +index b5bd3de87..5a52a0b19 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -785,11 +785,33 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -785,11 +785,34 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -38,9 +40,12 @@ Signed-off-by: John Crispin + qcom-ipq4019-map-ac2200.dtb \ + qcom-ipq4019-qxwlan-e2600ac-c1.dtb \ + qcom-ipq4019-qxwlan-e2600ac-c2.dtb \ ++ qcom-ipq4019-unielec-u4019-32m.dtb \ + qcom-ipq4028-wpj428.dtb \ + qcom-ipq4029-gl-b1300.dtb \ + qcom-ipq4029-mr33.dtb \ qcom-ipq8064-ap148.dtb \ qcom-msm8660-surf.dtb \ qcom-msm8960-cdp.dtb \ +-- +2.20.1 -- cgit v1.2.3