From 4a77a060ab6219f830390cd53c2817b621f39760 Mon Sep 17 00:00:00 2001 From: Yanase Yuki Date: Wed, 29 Jan 2020 19:27:25 +0900 Subject: ipq40xx: add support for Buffalo WTR-M2133HP Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019. Specification ------------- - SoC: Qualcomm IPQ4019 - RAM: 512MiB - Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC) - Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch) - Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch) - Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch) - Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN) - LED: 4x white LED, 4x orange LED, 1x blue LED - USB: 1x USB 3.0 port - Input: 2x tactile switch, 2x slide switch (2x SP3T) - Serial console: 115200bps, pinheader JP5 on PCB - Power: DC 12V 2A Flash instruction ----------------- 1. Set up a TFTP server (IP address: 192.168.11.10) 2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage" and put it into the TFTP server directory. 3. Connect the TFTP server and WTR-M2133HP. 4. Hold down the AOSS button, then power on the router. 5. After booting OpenWrt initramfs image, connect to the router by SSH. 6. Transfer "squashfs-nand-factory.ubi" to the router. 7. Execute the following commands. # ubidetach -p /dev/mtd15 # ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi # fw_setenv bootcmd bootipq 8. Perform reboot. Recover to stock firmware ------------------------- 1. Execute the following command. # fw_setenv bootcmd bootbf 2. Reboot and wait several minutes. Signed-off-by: Yanase Yuki --- .../ipq40xx/base-files/etc/board.d/02_network | 5 + .../etc/hotplug.d/firmware/11-ath10k-caldata | 12 + .../ipq40xx/base-files/lib/upgrade/platform.sh | 1 + .../arch/arm/boot/dts/qcom-ipq4019-wtr-m2133hp.dts | 419 +++++++++++++++++++++ target/linux/ipq40xx/image/Makefile | 12 + .../patches-4.19/901-arm-boot-add-dts-files.patch | 1 + .../patches-5.4/901-arm-boot-add-dts-files.patch | 1 + 7 files changed, 451 insertions(+) create mode 100644 target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-wtr-m2133hp.dts (limited to 'target/linux/ipq40xx') diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index cd336a9e6a..61d02a17bc 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -65,6 +65,11 @@ ipq40xx_setup_interfaces() engenius,eap2200) ucidef_set_interface_lan "eth0 eth1" ;; + buffalo,wtr-m2133hp) + ucidef_set_interfaces_lan_wan "eth0" "eth1" + ucidef_add_switch "switch0" \ + "0u@eth0" "2:lan:3" "3:lan:2" "4:lan:1" + ;; cellc,rtl30vw) ucidef_set_interface_lan "eth0" ucidef_add_switch "switch0" \ diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index b95bab7cae..8df7990f2e 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -31,6 +31,10 @@ case "$FIRMWARE" in /usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \ /usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") ;; + buffalo,wtr-m2133hp) + caldata_extract "ART" 0x9000 0x2f20 + ath10k_patch_mac $(mtd_get_mac_binary ORGDATA 0x32) + ;; engenius,eap2200 |\ openmesh,a62) caldata_extract "0:ART" 0x9000 0x2f20 @@ -82,6 +86,10 @@ case "$FIRMWARE" in /usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \ /usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x207 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") ;; + buffalo,wtr-m2133hp) + caldata_extract "ART" 0x1000 0x2f20 + ath10k_patch_mac $(mtd_get_mac_binary ORGDATA 0x26) + ;; cellc,rtl30vw |\ compex,wpj419 |\ compex,wpj428 |\ @@ -171,6 +179,10 @@ case "$FIRMWARE" in /usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \ /usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x208 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") ;; + buffalo,wtr-m2133hp) + caldata_extract "ART" 0x5000 0x2f20 + ath10k_patch_mac $(mtd_get_mac_binary ORGDATA 0x2c) + ;; cellc,rtl30vw |\ compex,wpj419 |\ compex,wpj428 |\ diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index 2abff3bd00..5b89710a22 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -64,6 +64,7 @@ platform_do_upgrade() { avm,fritzbox-7530 |\ avm,fritzrepeater-1200 |\ avm,fritzrepeater-3000 |\ + buffalo,wtr-m2133hp |\ cilab,meshpoint-one |\ engenius,eap2200 |\ mobipromo,cm520-79f |\ diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-wtr-m2133hp.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-wtr-m2133hp.dts new file mode 100644 index 0000000000..1977358525 --- /dev/null +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-wtr-m2133hp.dts @@ -0,0 +1,419 @@ +// SPDX-License-Identifier: ISC +/* + * Copyright (c) 2015 - 2016, The Linux Foundation. All rights reserved. + * Copyright (c) 2020 Yanase Yuki + */ + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + model = "Buffalo WTR-M2133HP"; + compatible = "buffalo,wtr-m2133hp", "qcom,ipq4019"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x20000000>; + }; + + chosen { + /* + * U-Boot adds "ubi.mtd=rootfs root=mtd:ubi_rootfs" to + * kernel command line. But we use different partition names, + * so we have to set correct parameters. + */ + bootargs-append = " ubi.mtd=ubi root=/dev/ubiblock0_1"; + }; + + aliases { + led-boot = &led_power_blue; + led-failsafe = &led_power_orange; + led-running = &led_power_white; + led-upgrade = &led_power_blue; + label-mac-device = &gmac0; + }; + + soc { + rng@22000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + status = "okay"; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + switch_lan_bmp = <0x1c>; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + + usb3@8af8800 { + status = "okay"; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_power_white: power_white { + label = "wtr-m2133hp:white:power"; + gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>; + }; + + led_power_orange: power_orange { + label = "wtr-m2133hp:orange:power"; + gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>; + }; + + led_power_blue: power_blue { + label = "wtr-m2133hp:blue:power"; + gpios = <&tlmm 43 GPIO_ACTIVE_HIGH>; + }; + + router_white { + label = "wtr-m2133hp:white:router"; + gpios = <&tlmm 28 GPIO_ACTIVE_HIGH>; + }; + + router_orange { + label = "wtr-m2133hp:orange:router"; + gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>; + }; + + internet_white { + label = "wtr-m2133hp:white:internet"; + gpios = <&tlmm 27 GPIO_ACTIVE_HIGH>; + }; + + internet_orange { + label = "wtr-m2133hp:orange:internet"; + gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>; + }; + + wireless_white { + label = "wtr-m2133hp:white:wireless"; + gpios = <&tlmm 24 GPIO_ACTIVE_HIGH>; + }; + + wireless_orange { + label = "wtr-m2133hp:orange:wireless"; + gpios = <&tlmm 44 GPIO_ACTIVE_HIGH>; + }; + }; + + keys { + compatible = "gpio-keys"; + + auto_mode { + label = "auto_mode"; + gpios = <&tlmm 9 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + }; + + router_mode { + label = "router_mode"; + gpios = <&tlmm 10 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + }; + + ap_mode { + label = "ap_mode"; + gpios = <&tlmm 11 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + }; + + reset { + label = "reset"; + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "AOSS Button"; + gpios = <&tlmm 32 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; +}; + +&tlmm { + serial_0_pins: serial0_pinmux { + mux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + mdio_pins: mdio_pinmux { + mux_1 { + pins = "gpio6"; + function = "mdio"; + bias-pull-up; + }; + + mux_2 { + pins = "gpio7"; + function = "mdc"; + bias-pull-up; + }; + }; + + nand_pins: nand_pins { + pullups { + pins = "gpio52", "gpio53", "gpio58", + "gpio59"; + function = "qpic"; + bias-pull-up; + }; + + pulldowns { + pins = "gpio54", "gpio55", "gpio56", + "gpio57", "gpio60", "gpio61", + "gpio62", "gpio63", "gpio64", + "gpio65", "gpio66", "gpio67", + "gpio68", "gpio69"; + function = "qpic"; + bias-pull-down; + }; + }; + + usb_power { + line-name = "USB power"; + gpios = <34 GPIO_ACTIVE_HIGH>; + gpio-hog; + output-high; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_0_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&pcie0 { + status = "okay"; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi@0,0 { + compatible = "qcom,ath10k"; + reg = <0 0 0 0 0>; + + qcom,ath10k-calibration-variant = "Buffalo-WTR-M2133HP"; + }; + }; +}; + +&qpic_bam { + status = "okay"; +}; + +&nand { + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + status = "okay"; + + nand@0 { + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "SBL1"; + reg = <0x0000000 0x0100000>; + read-only; + }; + + partition@100000 { + label = "MIBIB"; + reg = <0x0100000 0x0100000>; + read-only; + }; + + partition@200000 { + label = "BOOTCONFIG"; + reg = <0x0200000 0x0100000>; + read-only; + }; + + partition@300000 { + label = "QSEE"; + reg = <0x0300000 0x0100000>; + read-only; + }; + + partition@400000 { + label = "QSEE_1"; + reg = <0x0400000 0x0100000>; + read-only; + }; + + partition@500000 { + label = "CDT"; + reg = <0x0500000 0x0080000>; + read-only; + }; + + partition@580000 { + label = "CDT_1"; + reg = <0x0580000 0x0080000>; + read-only; + }; + + partition@600000 { + label = "BOOTCONFIG1"; + reg = <0x0600000 0x0080000>; + read-only; + }; + + partition@680000 { + label = "APPSBLENV"; + reg = <0x0680000 0x0080000>; + }; + + partition@700000 { + label = "APPSBL"; + reg = <0x0700000 0x0200000>; + read-only; + }; + + partition@900000 { + label = "APPSBL_1"; + reg = <0x0900000 0x0200000>; + read-only; + }; + + art: partition@b00000 { + label = "ART"; + reg = <0x0b00000 0x0080000>; + read-only; + }; + + partition@b80000 { + label = "ART_1"; + reg = <0x0b80000 0x0080000>; + read-only; + }; + + orgdata: partition@c00000 { + label = "ORGDATA"; + reg = <0x0c00000 0x0080000>; + read-only; + }; + + partition@c80000 { + label = "ORGDATA_1"; + reg = <0x0c80000 0x0080000>; + read-only; + }; + + partition@d00000 { + label = "ubi"; + reg = <0x0d00000 0x2900000>; + }; + + partition@3600000 { + label = "rootfs_recover"; + reg = <0x3600000 0x2900000>; + read-only; + }; + + partition@5f00000 { + label = "user_property"; + reg = <0x5f00000 0x1a20000>; + read-only; + }; + }; + }; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "Buffalo-WTR-M2133HP"; + ieee80211-freq-limit = <2400000 2483000>; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "Buffalo-WTR-M2133HP"; +}; + +&mdio { + status = "okay"; + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + reset-gpios = <&tlmm 47 GPIO_ACTIVE_LOW>; +}; + +&gmac0 { + mtd-mac-address = <&orgdata 0x20>; +}; + +&gmac1 { + mtd-mac-address = <&orgdata 0x20>; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index 5336649c3d..51e8bcc7e3 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -245,6 +245,18 @@ define Device/avm_fritzrepeater-3000 endef TARGET_DEVICES += avm_fritzrepeater-3000 +define Device/buffalo_wtr-m2133hp + $(call Device/FitImage) + $(call Device/UbiFit) + DEVICE_VENDOR := Buffalo + DEVICE_MODEL := WTR-M2133HP + SOC := qcom-ipq4019 + DEVICE_PACKAGES := uboot-envtools ath10k-firmware-qca9984-ct ipq-wifi-buffalo_wtr-m2133hp + BLOCKSIZE := 128k + PAGESIZE := 2048 +endef +TARGET_DEVICES += buffalo_wtr-m2133hp + define Device/cellc_rtl30vw KERNEL_SUFFIX := -fit-uImage.itb KERNEL_INITRAMFS = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch index fb358ed184..924715c9aa 100644 --- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch @@ -49,6 +49,7 @@ Signed-off-by: John Crispin + qcom-ipq4019-rtl30vw.dtb \ + qcom-ipq4019-u4019-32m.dtb \ + qcom-ipq4019-wpj419.dtb \ ++ qcom-ipq4019-wtr-m2133hp.dtb \ + qcom-ipq4028-wpj428.dtb \ + qcom-ipq4029-ap-303.dtb \ + qcom-ipq4029-ap-303h.dtb \ diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch index 2db36aa597..c5b0981f49 100644 --- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch @@ -50,6 +50,7 @@ Signed-off-by: John Crispin + qcom-ipq4019-rtl30vw.dtb \ + qcom-ipq4019-u4019-32m.dtb \ + qcom-ipq4019-wpj419.dtb \ ++ qcom-ipq4019-wtr-m2133hp.dtb \ + qcom-ipq4028-wpj428.dtb \ + qcom-ipq4029-ap-303.dtb \ + qcom-ipq4029-ap-303h.dtb \ -- cgit v1.2.3