From 3f61e5e1b97eed335bdd2f6befcc633f5d1dde07 Mon Sep 17 00:00:00 2001 From: Yen-Ting-Shen Date: Fri, 1 Nov 2019 15:47:28 +0800 Subject: ipq40xx: add support for EnGenius EMR3500 SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8072 (2 ports) USB: 1 x 2.0 (Host controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET Button LEDS: White, Blue, Red, Orange Flash instruction: From EnGenius firmware to OpenWrt firmware: In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emr3500-squashfs-factory.bin directly. From OpenWrt firmware to EnGenius firmware: 1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8 Put the EnGenius firmware in the TFTP server directory on your computer. 2. Power up EMR3500. Press 4 and then press any key to enter u-boot. 3. Download EnGenius firmware (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emr3500-nor-fw-s.img 4. Flash the firmware (IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script 5. Reboot (IPQ40xx) # reset Signed-off-by: Yen-Ting-Shen [squashed update patch, updated to 5.4, dropped BOARD_NAME, migrated to SOC] Signed-off-by: Christian Lamparter --- .../ipq40xx/base-files/etc/board.d/02_network | 6 + .../etc/hotplug.d/firmware/11-ath10k-caldata | 8 + .../arch/arm/boot/dts/qcom-ipq4018-emr3500.dts | 235 +++++++++++++++++++++ target/linux/ipq40xx/image/Makefile | 14 ++ .../patches-5.4/901-arm-boot-add-dts-files.patch | 3 +- 5 files changed, 265 insertions(+), 1 deletion(-) create mode 100644 target/linux/ipq40xx/files-5.4/arch/arm/boot/dts/qcom-ipq4018-emr3500.dts (limited to 'target/linux/ipq40xx') diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 85f9c174ad..77a2241283 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -15,6 +15,7 @@ ipq40xx_setup_interfaces() 8dev,habanero-dvk|\ 8dev,jalapeno|\ alfa-network,ap120c-ac|\ + engenius,emr3500|\ engenius,ens620ext) ucidef_set_interfaces_lan_wan "eth0" "eth1" ;; @@ -130,6 +131,11 @@ ipq40xx_setup_macs() lan_mac=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr) label_mac=$lan_mac ;; + engenius,emr3500) + wan_mac=$(mtd_get_mac_ascii 0:APPSBLENV wanaddr) + lan_mac=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr) + label_mac=$wan_mac + ;; engenius,ens620ext) wan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr) lan_mac=$(macaddr_add "$wan_mac" 1) diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 27373466fa..e41baecf69 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -101,6 +101,10 @@ case "$FIRMWARE" in caldata_extract "0:ART" 0x1000 0x2f20 ath10k_patch_mac $(mtd_get_mac_ascii 0:APPSBLENV wlanaddr) ;; + engenius,emr3500) + caldata_extract "0:ART" 0x1000 0x2f20 + ath10k_patch_mac $(mtd_get_mac_ascii 0:APPSBLENV ethaddr) + ;; engenius,ens620ext) caldata_extract "ART" 0x1000 0x2f20 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +2) @@ -185,6 +189,10 @@ case "$FIRMWARE" in caldata_extract "0:ART" 0x5000 0x2f20 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii 0:APPSBLENV wlanaddr) +1) ;; + engenius,emr3500) + caldata_extract "0:ART" 0x5000 0x2f20 + ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii 0:APPSBLENV ethaddr) +1) + ;; engenius,ens620ext) caldata_extract "ART" 0x5000 0x2f20 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +3) diff --git a/target/linux/ipq40xx/files-5.4/arch/arm/boot/dts/qcom-ipq4018-emr3500.dts b/target/linux/ipq40xx/files-5.4/arch/arm/boot/dts/qcom-ipq4018-emr3500.dts new file mode 100644 index 0000000000..50067aaa91 --- /dev/null +++ b/target/linux/ipq40xx/files-5.4/arch/arm/boot/dts/qcom-ipq4018-emr3500.dts @@ -0,0 +1,235 @@ +// SPDX-License-Identifier: GPL-2.0-or-later + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + model = "EnGenius EMR3500"; + compatible = "engenius,emr3500"; + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + usb2_hs_phy: hsphy@a8000 { + status = "okay"; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 59 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + aliases { + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + }; + + leds { + compatible = "gpio-leds"; + + power: white { + label = "emr3500:white:power"; + gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>; + }; + + blue { + label = "emr3500:blue"; + gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>; + }; + + red { + label = "emr3500:red"; + gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>; + }; + + orange { + label = "emr3500:orange"; + gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&tlmm { + serial_pins: serial_pinmux { + mux { + pins = "gpio60", "gpio61"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pin { + function = "blsp_spi0"; + pins = "gpio54", "gpio55", "gpio56", "gpio57"; + drive-strength = <12>; + bias-disable; + }; + pin_cs { + function = "gpio"; + pins = "gpio54"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_spi1 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>; + + m25p80@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <24000000>; + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:SBL1"; + reg = <0x00000000 0x00040000>; + read-only; + }; + partition@40000 { + label = "0:MIBIB"; + reg = <0x00040000 0x00020000>; + read-only; + }; + partition@60000 { + label = "0:QSEE"; + reg = <0x00060000 0x00060000>; + read-only; + }; + partition@c0000 { + label = "0:CDT"; + reg = <0x000c0000 0x00010000>; + read-only; + }; + partition@d0000 { + label = "0:DDRPARAMS"; + reg = <0x000d0000 0x00010000>; + read-only; + }; + partition@e0000 { + label = "0:APPSBLENV"; + reg = <0x000e0000 0x00010000>; + read-only; + }; + partition@f0000 { + label = "0:APPSBL"; + reg = <0x000f0000 0x00080000>; + read-only; + }; + partition@170000 { + label = "0:ART"; + reg = <0x00170000 0x00010000>; + read-only; + }; + partition@180000 { + label = "userconfig"; + reg = <0x00180000 0x00080000>; + read-only; + }; + partition@200000 { + compatible = "denx,fit"; + label = "firmware"; + reg = <0x200000 0x1e00000>; + }; + }; + }; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&gmac0 { + vlan_tag = <1 0x10>; +}; + +&gmac1 { + vlan_tag = <2 0x20>; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "EnGenius-EMR3500"; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "EnGenius-EMR3500"; +}; diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index 5e6bd1d1b7..1d9f20b85f 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -378,6 +378,20 @@ define Device/engenius_emd1 endef TARGET_DEVICES += engenius_emd1 +define Device/engenius_emr3500 + $(call Device/FitImage) + DEVICE_VENDOR := EnGenius + DEVICE_MODEL := EMR3500 + DEVICE_DTS_CONFIG := config@4 + SOC := qcom-ipq4018 + KERNEL_SIZE := 4096k + IMAGE_SIZE := 30720k + IMAGES := sysupgrade.bin factory.bin + IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata + IMAGE/factory.bin := qsdk-ipq-factory-nor | check-size +endef +TARGET_DEVICES += engenius_emr3500 + define Device/engenius_ens620ext $(call Device/FitImage) DEVICE_VENDOR := EnGenius diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch index 5ce59979a0..371faa3a09 100644 --- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -837,11 +837,47 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -837,11 +837,48 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -21,6 +21,7 @@ Signed-off-by: John Crispin + qcom-ipq4018-ea6350v3.dtb \ + qcom-ipq4018-eap1300.dtb \ + qcom-ipq4018-emd1.dtb \ ++ qcom-ipq4018-emr3500.dtb \ + qcom-ipq4018-ens620ext.dtb \ + qcom-ipq4018-ex6100v2.dtb \ + qcom-ipq4018-ex6150v2.dtb \ -- cgit v1.2.3