From 4943afd7818f56053231a5a7ae90e55da44f1f08 Mon Sep 17 00:00:00 2001 From: Chris Blake Date: Sat, 10 Mar 2018 10:59:18 +0100 Subject: ipq40xx: add Cisco Meraki MR33 Support This patch adds support for Cisco Meraki MR33 hardware highlights: SOC: IPQ4029 Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB DDR3L-1600 @ 627 MHz Micron MT41K128M16JT-125IT NAND: 128 MiB SLC NAND Spansion S34ML01G200TFV00 (106 MiB usable) ETH: Qualcomm Atheros AR8035 Gigabit PHY (1 x LAN/WAN) + PoE WLAN1: QCA9887 (168c:0050) PCIe 1x1:1 802.11abgn ac Dualband VHT80 WLAN2: Qualcomm Atheros QCA4029 2.4GHz 802.11bgn 2:2x2 WLAN3: Qualcomm Atheros QCA4029 5GHz 802.11a/n/ac 2:2x2 VHT80 LEDS: 1 x Programmable RGB+White Status LED (driven by Ti LP5562 on i2c-1) 1 x Orange LED Fault Indicator (shared with LP5562) 2 x LAN Activity / Speed LEDs (On the RJ45 Port) BUTTON: one Reset button MISC: Bluetooth LE Ti cc2650 PG2.3 4x4mm - BL_CONFIG at 0x0001FFD8 AT24C64 8KiB EEPROM Kensington Lock Serial: WARNING: The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 115200-8-N-1. The board has a populated 1x4 0.1" header with half-height/low profile pins. The pinout is: VCC (little white arrow), RX, TX, GND. Flashing needs a serial adaptor, as well as patched ubootwrite utility (needs Little-Endian support). And a modified u-boot (enabled Ethernet). Meraki's original u-boot source can be found in: Add images to do an installation via bootloader: 0. open up the MR33 and connect the serial console. 1. start the 2nd stage bootloader transfer from client pc: # ubootwrite.py --write=mr33-uboot.bin (The ubootwrite tool will interrupt the boot-process and hence it needs to listen for cues. If the connection is bad (due to the low-profile pins), the tool can fail multiple times and in weird ways. If you are not sure, just use a terminal program and see what the device is doing there. 2. power on the MR33 (with ethernet + serial cables attached) Warning: Make sure you do this in a private LAN that has no connection to the internet. - let it upload the u-boot this can take 250-300 seconds - 3. use a tftp client (in binary mode!) on your PC to upload the sysupgrade.bin (the u-boot is listening on 192.168.1.1) # tftp 192.168.1.1 binary put openwrt-ipq40xx-meraki_mr33-squashfs-sysupgrade.bin 4. wait for it to reboot 5. connect to your MR33 via ssh on 192.168.1.1 For more detailed instructions, please take a look at the: "Flashing Instructions for the MR33" PDF. This can be found on the wiki: (A link to the mr33-uboot.bin + the modified ubootwrite is also there) Thanks to Jerome C. for sending an MR33 to Chris. Signed-off-by: Chris Blake Signed-off-by: Mathias Kresin Signed-off-by: Christian Lamparter --- .../linux/ipq40xx/base-files/etc/board.d/01_leds | 3 + .../ipq40xx/base-files/etc/board.d/02_network | 4 ++ .../etc/hotplug.d/firmware/11-ath10k-caldata | 74 ++++++++++++++++++++++ .../lib/preinit/05_set_iface_mac_ipq40xx.sh | 14 ++++ .../ipq40xx/base-files/lib/upgrade/platform.sh | 7 ++ 5 files changed, 102 insertions(+) create mode 100644 target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh (limited to 'target/linux/ipq40xx/base-files') diff --git a/target/linux/ipq40xx/base-files/etc/board.d/01_leds b/target/linux/ipq40xx/base-files/etc/board.d/01_leds index 6a493be3ec..f1f49abb2e 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/01_leds +++ b/target/linux/ipq40xx/base-files/etc/board.d/01_leds @@ -26,6 +26,9 @@ avm,fritzbox-4040) glinet,gl-b1300) ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:green:wlan" "phy0tpt" ;; +meraki,mr33) + ucidef_set_interface_lan "eth0" + ;; *) ;; esac diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 8f8d67db32..d25a039f2d 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -35,6 +35,10 @@ glinet,gl-b1300) openmesh,a42) ucidef_set_interfaces_lan_wan "eth1" "eth0" ;; + +meraki,mr33) + ucidef_set_interface_lan "eth0" + ;; *) echo "Unsupported hardware. Network interfaces not intialized" ;; diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index bc64d5b8ab..4322c4f3fa 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -1,5 +1,21 @@ #!/bin/sh +# xor multiple hex values of the same length +xor() { + local val + local ret="0x$1" + local retlen=${#1} + + shift + while [ -n "$1" ]; do + val="0x$1" + ret=$((ret ^ val)) + shift + done + + printf "%0${retlen}x" "$ret" +} + ath10kcal_die() { echo "ath10cal: " "$*" exit 1 @@ -37,6 +53,45 @@ ath10kcal_ubi_extract() { ath10kcal_die "failed to extract from $ubi" } +ath10kcal_patch_mac() { + local mac=$1 + + [ -z "$mac" ] && return + + macaddr_2bin $mac | dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=6 count=6 +} + +ath10kcal_patch_mac_crc() { + local mac=$1 + local mac_offset=6 + local chksum_offset=2 + local xor_mac + local xor_fw_mac + local xor_fw_chksum + + xor_fw_mac=$(hexdump -v -n 6 -s $mac_offset -e '/1 "%02x"' /lib/firmware/$FIRMWARE) + xor_fw_mac="${xor_fw_mac:0:4} ${xor_fw_mac:4:4} ${xor_fw_mac:8:4}" + + ath10kcal_patch_mac "$mac" && { + xor_mac=${mac//:/} + xor_mac="${xor_mac:0:4} ${xor_mac:4:4} ${xor_mac:8:4}" + + xor_fw_chksum=$(hexdump -v -n 2 -s $chksum_offset -e '/1 "%02x"' /lib/firmware/$FIRMWARE) + xor_fw_chksum=$(xor $xor_fw_chksum $xor_fw_mac $xor_mac) + + printf "%b" "\x${xor_fw_chksum:0:2}\x${xor_fw_chksum:2:2}" | \ + dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=$chksum_offset count=2 + } +} + +ath10kcal_is_caldata_valid() { + local expected="$1" + + magic=$(hexdump -v -n 2 -e '1/1 "%02x"' /lib/firmware/$FIRMWARE) + [[ "$magic" == "$expected" ]] + return $? +} + [ -e /lib/firmware/$FIRMWARE ] && exit 0 . /lib/functions.sh @@ -46,6 +101,15 @@ board=$(board_name) case "$FIRMWARE" in +"ath10k/cal-pci-0000:01:00.0.bin") + case "$board" in + meraki,mr33) + ath10kcal_ubi_extract "ART" 36864 2116 + ath10kcal_is_caldata_valid "4408" || ath10kcal_extract "ART" 36864 2116 + ath10kcal_patch_mac $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 102) +1) + ;; + esac + ;; "ath10k/pre-cal-ahb-a000000.wifi.bin") case "$board" in asus,rt-ac58u) @@ -59,6 +123,11 @@ case "$FIRMWARE" in qcom,ap-dk01.1-c1) ath10kcal_extract "ART" 4096 12064 ;; + meraki,mr33) + ath10kcal_ubi_extract "ART" 4096 12064 + ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 4096 12064 + ath10kcal_patch_mac_crc $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 102) +2) + ;; openmesh,a42) ath10kcal_extract "0:ART" 4096 12064 ;; @@ -77,6 +146,11 @@ case "$FIRMWARE" in qcom,ap-dk01.1-c1) ath10kcal_extract "ART" 20480 12064 ;; + meraki,mr33) + ath10kcal_ubi_extract "ART" 20480 12064 + ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 20480 12064 + ath10kcal_patch_mac_crc $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 102) +3) + ;; openmesh,a42) ath10kcal_extract "0:ART" 20480 12064 ;; diff --git a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh new file mode 100644 index 0000000000..1acd7366c8 --- /dev/null +++ b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh @@ -0,0 +1,14 @@ +#!/bin/sh + +. /lib/functions.sh + +preinit_set_mac_address() { + case $(board_name) in + meraki,mr33) + mac_lan=$(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 102) + [ -n "$mac_lan" ] && ip link set dev eth0 address "$mac_lan" + ;; + esac +} + +boot_hook_add preinit_main preinit_set_mac_address diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index 261c468813..52aa2321e3 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -40,6 +40,10 @@ platform_do_upgrade() { PART_NAME="inactive" platform_do_upgrade_openmesh "$ARGV" ;; + meraki,mr33) + CI_KERNPART="part.safe" + nand_do_upgrade "$1" + ;; *) default_do_upgrade "$ARGV" ;; @@ -52,6 +56,9 @@ platform_nand_pre_upgrade() { CI_UBIPART="UBI_DEV" CI_KERNPART="linux" ;; + meraki,mr33) + CI_KERNPART="part.safe" + ;; esac } -- cgit v1.2.3