From ea5bb6bbfee06f44f714aff40c8929505face221 Mon Sep 17 00:00:00 2001 From: Marek Lindner Date: Sun, 25 Nov 2018 21:46:54 +0800 Subject: ipq40xx: add support for Plasma Cloud PA1200 Device specifications: * QCA IPQ4018 * 256 MB of RAM * 32 MB of SPI NOR flash (w25q256) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200 * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200 * 3x GPIO-LEDs for status (cyan, purple, yellow) * 1x GPIO-button (reset) * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio4: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + used as LAN interface - phy@mdio3: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 802.3af/at POE(+) + used as WAN interface * 12V/24V 1A DC Flashing instructions: The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Marek Lindner [sven@narfation.org: prepare commit message, rebase, use all LEDs, switch to dualboot_datachk upgrade script, use eth1 as designated WAN interface] Signed-off-by: Sven Eckelmann --- target/linux/ipq40xx/base-files/etc/board.d/02_network | 3 ++- .../linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | 2 ++ 2 files changed, 4 insertions(+), 1 deletion(-) (limited to 'target/linux/ipq40xx/base-files/etc') diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 86787eeffd..b9e79c3b68 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -17,7 +17,8 @@ ipq40xx_setup_interfaces() alfa-network,ap120c-ac|\ engenius,emr3500|\ engenius,ens620ext|\ - luma,wrtq-329acn) + luma,wrtq-329acn|\ + plasmacloud,pa1200) ucidef_set_interfaces_lan_wan "eth0" "eth1" ;; aruba,ap-303|\ diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index f33d3f331c..ade0d74341 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -101,6 +101,7 @@ case "$FIRMWARE" in luma,wrtq-329acn|\ openmesh,a42 |\ openmesh,a62 |\ + plasmacloud,pa1200 |\ qxwlan,e2600ac-c1 |\ qxwlan,e2600ac-c2 |\ unielec,u4019-32m) @@ -198,6 +199,7 @@ case "$FIRMWARE" in luma,wrtq-329acn|\ openmesh,a42 |\ openmesh,a62 |\ + plasmacloud,pa1200 |\ qxwlan,e2600ac-c1 |\ qxwlan,e2600ac-c2 |\ unielec,u4019-32m) -- cgit v1.2.3