From 4871fd2616acb03fefe69b068955dba36eb00770 Mon Sep 17 00:00:00 2001 From: Marek Lindner Date: Fri, 14 Dec 2018 23:46:53 +0800 Subject: ipq40xx: add support for Plasma Cloud PA2200 Device specifications: * QCA IPQ4019 * 256 MB of RAM * 32 MB of SPI NOR flash (w25q256) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200 * 2T2R 5 GHz (channel 36-64) - QCA9888 hw2.0 (PCI) - requires special BDF in QCA9888/hw2.0/board-2.bin bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200 * 2T2R 5 GHz (channel 100-165) - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200 * GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE * GPIO-LEDs for power (orange) and status (blue) * 1x GPIO-button (reset) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio3: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + used as LAN interface - phy@mdio4: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 802.3at POE+ + used as WAN interface * 12V 2A DC Flashing instructions: The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Marek Lindner [sven@narfation.org: prepare commit message, rebase, use all LEDs, switch to dualboot_datachk upgrade script, use eth1 as designated WAN interface] Signed-off-by: Sven Eckelmann --- .../ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) (limited to 'target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata') diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index ade0d74341..e50732586a 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -36,7 +36,8 @@ case "$FIRMWARE" in ath10k_patch_mac $(mtd_get_mac_binary ORGDATA 0x32) ;; engenius,eap2200 |\ - openmesh,a62) + openmesh,a62 |\ + plasmacloud,pa2200) caldata_extract "0:ART" 0x9000 0x2f20 ;; linksys,ea8300 |\ @@ -102,6 +103,7 @@ case "$FIRMWARE" in openmesh,a42 |\ openmesh,a62 |\ plasmacloud,pa1200 |\ + plasmacloud,pa2200 |\ qxwlan,e2600ac-c1 |\ qxwlan,e2600ac-c2 |\ unielec,u4019-32m) @@ -200,6 +202,7 @@ case "$FIRMWARE" in openmesh,a42 |\ openmesh,a62 |\ plasmacloud,pa1200 |\ + plasmacloud,pa2200 |\ qxwlan,e2600ac-c1 |\ qxwlan,e2600ac-c2 |\ unielec,u4019-32m) -- cgit v1.2.3