From 2b4ac79a791d9451f601d494dde2e71864174358 Mon Sep 17 00:00:00 2001 From: Steven Lin Date: Fri, 19 Oct 2018 16:55:08 +0800 Subject: ipq40xx: add support for EnGenius EAP1300 MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET Button LEDS: Power, LAN, MESH, WLAN 2.4GHz, WLAN 5GHz 1. Load Ramdisk via U-Boot To set up the flash memory environment, do the following: a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters: * 115200bps * 8N1 b. Confirm that the PC is connected to the board using one of the Ethernet ports. Set a static ip 192.168.99.8 for Ethernet that connects to board. The PC must have a TFTP server launched and listening on the interface to which the board is connected. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown. U-BOOT> set serverip 192.168.99.8 && set ipaddr 192.168.99.9 && tftpboot 0x84000000 openwrt.itb && bootm 2. Load image via GUI a. Upgrade EAP1300 to FW v3.5.3.2 In the GUI, System Manager > Firmware > Firmware Upgrade, to do upgrade. b. Transfer to OpenWrt from EnGenius. In Firmware Upgrade page, to upgrade yours openwrt-ipq40xx-engenius_eap1300-squashfs-sysupgrade.bin. 3. Revert to EnGenius EAP1300 To flash openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin by using sysupgrade command and "DO NOT" keep configuration. $ sysupgrade –n openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin Signed-off-by: Steven Lin --- target/linux/ipq40xx/base-files/etc/board.d/02_network | 13 +++++++------ 1 file changed, 7 insertions(+), 6 deletions(-) (limited to 'target/linux/ipq40xx/base-files/etc/board.d/02_network') diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 5c90ef136f..d73914c7c1 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -33,6 +33,13 @@ avm,fritzbox-4040) compex,wpj428) ucidef_set_interface_lan "eth0 eth1" ;; +engenius,eap1300 |\ +meraki,mr33 |\ +netgear,ex6100v2 |\ +netgear,ex6150v2 |\ +zyxel,wre6606) + ucidef_set_interface_lan "eth0" + ;; glinet,gl-b1300) ucidef_set_interfaces_lan_wan "eth0" "eth1" ucidef_add_switch "switch0" \ @@ -42,12 +49,6 @@ openmesh,a42 |\ openmesh,a62) ucidef_set_interfaces_lan_wan "eth1" "eth0" ;; -meraki,mr33 |\ -netgear,ex6100v2 |\ -netgear,ex6150v2 |\ -zyxel,wre6606) - ucidef_set_interface_lan "eth0" - ;; zyxel,nbg6617) ucidef_set_interfaces_lan_wan "eth0" "eth1" ucidef_add_switch "switch0" \ -- cgit v1.2.3