From fce21ae4ccfcee0c28fb18f5507e145fb0b02dec Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= Date: Wed, 22 Mar 2017 21:09:00 +0100 Subject: brcm2708: rename all patches from raspberrypi git tree to use 950 prefix MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Right now all brcm2708 patches are extracted from the non-mainline raspberrypi/linux git tree. Many of them are hacks and/or are unneeded in LEDE. Raspberry Pi is getting better and better mainline support so it would be nice to finally start maintaining patches in a cleaner way: 1) Backport patches accepted in upstream tree 2) Start using upstream drivers 3) Pick only these patches that are needed for more complete support Handling above tasks requires grouping patches - ideally using the same prefixes as generic ones. It means we should rename existing patches to use some high prefix. This will allow e.g. use 0xx for backported code. Signed-off-by: Rafał Miłecki Acked-by: Florian Fainelli Acked-by: Stijn Tintel --- ...0054-BCM2708-Add-core-Device-Tree-support.patch | 9790 ++++++++++++++++++++ 1 file changed, 9790 insertions(+) create mode 100644 target/linux/brcm2708/patches-4.9/950-0054-BCM2708-Add-core-Device-Tree-support.patch (limited to 'target/linux/brcm2708/patches-4.9/950-0054-BCM2708-Add-core-Device-Tree-support.patch') diff --git a/target/linux/brcm2708/patches-4.9/950-0054-BCM2708-Add-core-Device-Tree-support.patch b/target/linux/brcm2708/patches-4.9/950-0054-BCM2708-Add-core-Device-Tree-support.patch new file mode 100644 index 0000000000..d9d1fa9a58 --- /dev/null +++ b/target/linux/brcm2708/patches-4.9/950-0054-BCM2708-Add-core-Device-Tree-support.patch @@ -0,0 +1,9790 @@ +From 589cd87acedc0e24214934816b6c16b4e76a894d Mon Sep 17 00:00:00 2001 +From: notro +Date: Wed, 9 Jul 2014 14:46:08 +0200 +Subject: [PATCH] BCM2708: Add core Device Tree support +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Add the bare minimum needed to boot BCM2708 from a Device Tree. + +Signed-off-by: Noralf Tronnes + +BCM2708: DT: change 'axi' nodename to 'soc' + +Change DT node named 'axi' to 'soc' so it matches ARCH_BCM2835. +The VC4 bootloader fills in certain properties in the 'axi' subtree, +but since this is part of an upstreaming effort, the name is changed. + +Signed-off-by: Noralf Tronnes notro@tronnes.org + +BCM2708_DT: Correct length of the peripheral space + +Use dts-dirs feature for overlays. + +The kernel makefiles have a dts-dirs target that is for vendor subdirectories. + +Using this fixes the install_dtbs target, which previously did not install the overlays. + +BCM270X_DT: configure I2S DMA channels + +Signed-off-by: Matthias Reichl + +BCM270X_DT: switch to bcm2835-i2s + +I2S soundcard drivers with proper devicetree support (i.e. not linking +to the cpu_dai/platform via name but to cpu/platform via of_node) +will work out of the box without any modifications. + +When the kernel is compiled without devicetree support the platform +code will instantiate the bcm2708-i2s driver and I2S soundcard drivers +will link to it via name, as before. + +Signed-off-by: Matthias Reichl + +SDIO-overlay: add poll_once-boolean parameter + +Add paramter to toggle sdio-device-polling +done every second or once at boot-time. + +Signed-off-by: Patrick Boettcher + +BCM270X_DT: Make mmc overlay compatible with current firmware + +The original DT overlay logic followed a merge-then-patch procedure, +i.e. parameters are applied to the loaded overlay before the overlay +is merged into the base DTB. This sequence has been changed to +patch-then-merge, in order to support parameterised node names, and +to protect against bad overlays. As a result, overrides (parameters) +must only target labels in the overlay, but the overlay can obviously target nodes in the base DTB. + +mmc-overlay.dts (that switches back to the original mmc sdcard +driver) is the only overlay violating that rule, and this patch +fixes it. + +bcm270x_dt: Use the sdhost MMC controller by default + +The "mmc" overlay reverts to using the other controller. + +squash: Add cprman to dt + +BCM270X_DT: Use clk_core for I2C interfaces + +BCM270X_DT: Use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi + +The mainline Device Tree files are quite close to downstream now. +Let's use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi as base files +for our dts files. + +Mainline dts files are based on these files: + + bcm2835-rpi.dtsi + bcm2835.dtsi bcm2836.dtsi + bcm283x.dtsi + +Current downstream are based on these: + + bcm2708.dtsi bcm2709.dtsi bcm2710.dtsi + bcm2708_common.dtsi + +This patch introduces this dependency: + + bcm2708.dtsi bcm2709.dtsi + bcm2708-rpi.dtsi + bcm270x.dtsi + bcm2835.dtsi bcm2836.dtsi + bcm283x.dtsi + +And: + bcm2710.dtsi + bcm2708-rpi.dtsi + bcm270x.dtsi + bcm283x.dtsi + +bcm270x.dtsi contains the downstream bcm283x.dtsi diff. +bcm2708-rpi.dtsi is the downstream version of bcm2835-rpi.dtsi. + +Other changes: +- The led node has moved from /soc/leds to /leds. This is not a problem + since the label is used to reference it. +- The clk_osc reg property changes from 6 to 3. +- The gpu nodes has their interrupt property set in the base file. +- the clocks label does not point to the /clocks node anymore, but + points to the cprman node. This is not a problem since the overlays + that use the clock node refer to it directly: target-path = "/clocks"; +- some nodes now have 2 labels since mainline and downstream differs in + this respect: cprman/clocks, spi0/spi, gpu/vc4. +- some nodes doesn't have an explicit status = "okay" since they're not + disabled in the base file: watchdog and random. +- gpiomem doesn't need an explicit status = "okay". +- bcm2708-rpi-cm.dts got the hpd-gpios property from bcm2708_common.dtsi, + it's now set directly in that file. +- bcm2709-rpi-2-b.dts has the timer node moved from /soc/timer to /timer. +- Removed clock-frequency property on the bcm{2709,2710}.dtsi timer nodes. + +Signed-off-by: Noralf Trønnes + +BCM270X_DT: Use raspberrypi-power to turn on USB power + +Use the raspberrypi-power driver to turn on USB power. + +Signed-off-by: Noralf Trønnes + +BCM270X_DT: Add a .dtbo target, use for overlays + +Change the filenames and extensions to keep the pre-DDT style of +overlay (-overlay.dtb) distinct from new ones that use a +different style of local fixups (.dtbo), and to match other +platforms. + +The RPi firmware uses the DDTK trailer atom to choose which type of +overlay to use for each kernel. + +Signed-off-by: Phil Elwell + +BCM270X_DT: Don't generate "linux,phandle" props + +The EPAPR standard says to use "phandle" properties to store phandles, +rather than the deprecated "linux,phandle" version. By default, dtc +generates both, but adding "-H epapr" causes it to only generate +"phandle"s, saving some space and clutter. + +Signed-off-by: Phil Elwell + +BCM270X_DT: Add overlay for enc28j60 on SPI2 + +Works on SPI2 for compute module + +BCM270X_DT: Add midi-uart0 overlay + +MIDI requires 31.25kbaud, a baudrate unsupported by Linux. The +midi-uart0 overlay configures uart0 (ttyAMA0) to use a fake clock +so that requesting 38.4kbaud actually gets 31.25kbaud. + +Signed-off-by: Phil Elwell + +BCM270X_DT: Add i2c-sensor overlay + +The i2c-sensor overlay is a container for various pressure and +temperature sensors, currently bmp085 and bmp280. The standalone +bmp085_i2c-sensor overlay is now deprecated. + +Signed-off-by: Phil Elwell + +BCM270X_DT: overlays/*-overlay.dtb -> overlays/*.dtbo (#1752) + +We now create overlays as .dtbo files. + +build: support for .dtbo files for dtb overlays + +Kernel 4.4.6+ on RaspberryPi support .dtbo files for overlays, instead of .dtb. +Patch the kernel, which has faulty rules to generate .dtbo the way yocto does + +Signed-off-by: Herve Jourdain +Signed-off-by: Khem Raj +--- + arch/arm/Makefile | 2 + + arch/arm/boot/.gitignore | 2 +- + arch/arm/boot/dts/Makefile | 19 + + arch/arm/boot/dts/bcm2708-rpi-b-plus.dts | 156 +++ + arch/arm/boot/dts/bcm2708-rpi-b.dts | 146 +++ + arch/arm/boot/dts/bcm2708-rpi-cm.dts | 105 ++ + arch/arm/boot/dts/bcm2708-rpi-cm.dtsi | 50 + + arch/arm/boot/dts/bcm2708-rpi.dtsi | 109 ++ + arch/arm/boot/dts/bcm2708.dtsi | 16 + + arch/arm/boot/dts/bcm2709-rpi-2-b.dts | 156 +++ + arch/arm/boot/dts/bcm2709.dtsi | 22 + + arch/arm/boot/dts/bcm270x.dtsi | 141 ++ + arch/arm/boot/dts/bcm2710-rpi-3-b.dts | 203 +++ + arch/arm/boot/dts/bcm2710-rpi-cm3.dts | 155 +++ + arch/arm/boot/dts/bcm2710.dtsi | 155 +++ + arch/arm/boot/dts/overlays/Makefile | 105 ++ + arch/arm/boot/dts/overlays/README | 1368 ++++++++++++++++++++ + .../arm/boot/dts/overlays/adau1977-adc-overlay.dts | 53 + + arch/arm/boot/dts/overlays/ads1015-overlay.dts | 98 ++ + arch/arm/boot/dts/overlays/ads7846-overlay.dts | 89 ++ + .../dts/overlays/akkordion-iqdacplus-overlay.dts | 46 + + .../allo-piano-dac-pcm512x-audio-overlay.dts | 54 + + arch/arm/boot/dts/overlays/at86rf233-overlay.dts | 57 + + .../audioinjector-wm8731-audio-overlay.dts | 39 + + arch/arm/boot/dts/overlays/audremap-overlay.dts | 19 + + .../dts/overlays/bmp085_i2c-sensor-overlay.dts | 23 + + arch/arm/boot/dts/overlays/dht11-overlay.dts | 39 + + .../boot/dts/overlays/dionaudio-loco-overlay.dts | 39 + + arch/arm/boot/dts/overlays/dpi18-overlay.dts | 31 + + arch/arm/boot/dts/overlays/dpi24-overlay.dts | 31 + + arch/arm/boot/dts/overlays/dwc-otg-overlay.dts | 20 + + arch/arm/boot/dts/overlays/dwc2-overlay.dts | 29 + + arch/arm/boot/dts/overlays/enc28j60-overlay.dts | 53 + + .../boot/dts/overlays/enc28j60-spi2-overlay.dts | 47 + + arch/arm/boot/dts/overlays/gpio-ir-overlay.dts | 44 + + .../boot/dts/overlays/gpio-poweroff-overlay.dts | 34 + + .../boot/dts/overlays/hifiberry-amp-overlay.dts | 39 + + .../boot/dts/overlays/hifiberry-dac-overlay.dts | 34 + + .../dts/overlays/hifiberry-dacplus-overlay.dts | 56 + + .../boot/dts/overlays/hifiberry-digi-overlay.dts | 39 + + .../dts/overlays/hifiberry-digi-pro-overlay.dts | 41 + + arch/arm/boot/dts/overlays/hy28a-overlay.dts | 93 ++ + arch/arm/boot/dts/overlays/hy28b-overlay.dts | 148 +++ + arch/arm/boot/dts/overlays/i2c-bcm2708-overlay.dts | 13 + + arch/arm/boot/dts/overlays/i2c-gpio-overlay.dts | 43 + + arch/arm/boot/dts/overlays/i2c-mux-overlay.dts | 139 ++ + .../boot/dts/overlays/i2c-pwm-pca9685a-overlay.dts | 26 + + arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts | 83 ++ + arch/arm/boot/dts/overlays/i2c-sensor-overlay.dts | 34 + + .../arm/boot/dts/overlays/i2c0-bcm2708-overlay.dts | 61 + + .../arm/boot/dts/overlays/i2c1-bcm2708-overlay.dts | 37 + + .../boot/dts/overlays/i2s-gpio28-31-overlay.dts | 18 + + arch/arm/boot/dts/overlays/iqaudio-dac-overlay.dts | 43 + + .../boot/dts/overlays/iqaudio-dacplus-overlay.dts | 46 + + .../overlays/iqaudio-digi-wm8804-audio-overlay.dts | 47 + + .../arm/boot/dts/overlays/justboom-dac-overlay.dts | 43 + + .../boot/dts/overlays/justboom-digi-overlay.dts | 39 + + arch/arm/boot/dts/overlays/lirc-rpi-overlay.dts | 57 + + arch/arm/boot/dts/overlays/mcp23017-overlay.dts | 54 + + arch/arm/boot/dts/overlays/mcp23s17-overlay.dts | 732 +++++++++++ + .../arm/boot/dts/overlays/mcp2515-can0-overlay.dts | 73 ++ + .../arm/boot/dts/overlays/mcp2515-can1-overlay.dts | 73 ++ + arch/arm/boot/dts/overlays/midi-uart0-overlay.dts | 36 + + arch/arm/boot/dts/overlays/mmc-overlay.dts | 38 + + arch/arm/boot/dts/overlays/mz61581-overlay.dts | 117 ++ + arch/arm/boot/dts/overlays/pi3-act-led-overlay.dts | 27 + + .../boot/dts/overlays/pi3-disable-bt-overlay.dts | 46 + + .../boot/dts/overlays/pi3-miniuart-bt-overlay.dts | 64 + + arch/arm/boot/dts/overlays/piscreen-overlay.dts | 102 ++ + arch/arm/boot/dts/overlays/piscreen2r-overlay.dts | 106 ++ + arch/arm/boot/dts/overlays/pisound-overlay.dts | 114 ++ + arch/arm/boot/dts/overlays/pitft22-overlay.dts | 69 + + .../dts/overlays/pitft28-capacitive-overlay.dts | 91 ++ + .../dts/overlays/pitft28-resistive-overlay.dts | 121 ++ + .../dts/overlays/pitft35-resistive-overlay.dts | 121 ++ + arch/arm/boot/dts/overlays/pps-gpio-overlay.dts | 35 + + arch/arm/boot/dts/overlays/pwm-2chan-overlay.dts | 47 + + arch/arm/boot/dts/overlays/pwm-overlay.dts | 43 + + arch/arm/boot/dts/overlays/qca7000-overlay.dts | 52 + + arch/arm/boot/dts/overlays/raspidac3-overlay.dts | 45 + + .../boot/dts/overlays/rpi-backlight-overlay.dts | 21 + + arch/arm/boot/dts/overlays/rpi-dac-overlay.dts | 34 + + arch/arm/boot/dts/overlays/rpi-display-overlay.dts | 89 ++ + arch/arm/boot/dts/overlays/rpi-ft5406-overlay.dts | 17 + + arch/arm/boot/dts/overlays/rpi-proto-overlay.dts | 39 + + arch/arm/boot/dts/overlays/rpi-sense-overlay.dts | 47 + + .../overlays/rra-digidac1-wm8741-audio-overlay.dts | 81 ++ + .../boot/dts/overlays/sc16is750-i2c-overlay.dts | 37 + + .../boot/dts/overlays/sc16is752-spi1-overlay.dts | 61 + + arch/arm/boot/dts/overlays/sdhost-overlay.dts | 32 + + arch/arm/boot/dts/overlays/sdio-1bit-overlay.dts | 36 + + arch/arm/boot/dts/overlays/sdio-overlay.dts | 36 + + arch/arm/boot/dts/overlays/sdtweak-overlay.dts | 23 + + arch/arm/boot/dts/overlays/smi-dev-overlay.dts | 18 + + arch/arm/boot/dts/overlays/smi-nand-overlay.dts | 69 + + arch/arm/boot/dts/overlays/smi-overlay.dts | 37 + + .../boot/dts/overlays/spi-gpio35-39-overlay.dts | 31 + + arch/arm/boot/dts/overlays/spi-rtc-overlay.dts | 33 + + arch/arm/boot/dts/overlays/spi0-hw-cs-overlay.dts | 26 + + arch/arm/boot/dts/overlays/spi1-1cs-overlay.dts | 57 + + arch/arm/boot/dts/overlays/spi1-2cs-overlay.dts | 69 + + arch/arm/boot/dts/overlays/spi1-3cs-overlay.dts | 81 ++ + arch/arm/boot/dts/overlays/spi2-1cs-overlay.dts | 57 + + arch/arm/boot/dts/overlays/spi2-2cs-overlay.dts | 69 + + arch/arm/boot/dts/overlays/spi2-3cs-overlay.dts | 81 ++ + arch/arm/boot/dts/overlays/tinylcd35-overlay.dts | 224 ++++ + arch/arm/boot/dts/overlays/uart1-overlay.dts | 38 + + .../arm/boot/dts/overlays/vc4-fkms-v3d-overlay.dts | 89 ++ + arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts | 136 ++ + arch/arm/boot/dts/overlays/vga666-overlay.dts | 30 + + arch/arm/boot/dts/overlays/w1-gpio-overlay.dts | 39 + + .../boot/dts/overlays/w1-gpio-pullup-overlay.dts | 41 + + arch/arm/boot/dts/overlays/wittypi-overlay.dts | 44 + + scripts/Makefile.dtbinst | 10 +- + scripts/Makefile.lib | 11 + + 115 files changed, 8979 insertions(+), 4 deletions(-) + create mode 100644 arch/arm/boot/dts/bcm2708-rpi-b-plus.dts + create mode 100644 arch/arm/boot/dts/bcm2708-rpi-b.dts + create mode 100644 arch/arm/boot/dts/bcm2708-rpi-cm.dts + create mode 100644 arch/arm/boot/dts/bcm2708-rpi-cm.dtsi + create mode 100644 arch/arm/boot/dts/bcm2708-rpi.dtsi + create mode 100644 arch/arm/boot/dts/bcm2708.dtsi + create mode 100644 arch/arm/boot/dts/bcm2709-rpi-2-b.dts + create mode 100644 arch/arm/boot/dts/bcm2709.dtsi + create mode 100644 arch/arm/boot/dts/bcm270x.dtsi + create mode 100644 arch/arm/boot/dts/bcm2710-rpi-3-b.dts + create mode 100644 arch/arm/boot/dts/bcm2710-rpi-cm3.dts + create mode 100644 arch/arm/boot/dts/bcm2710.dtsi + create mode 100644 arch/arm/boot/dts/overlays/Makefile + create mode 100644 arch/arm/boot/dts/overlays/README + create mode 100644 arch/arm/boot/dts/overlays/adau1977-adc-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/ads1015-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/ads7846-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/akkordion-iqdacplus-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/allo-piano-dac-pcm512x-audio-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/at86rf233-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/audioinjector-wm8731-audio-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/audremap-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/bmp085_i2c-sensor-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/dht11-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/dionaudio-loco-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/dpi18-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/dpi24-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/dwc-otg-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/dwc2-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/enc28j60-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/enc28j60-spi2-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/gpio-ir-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/gpio-poweroff-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/hifiberry-amp-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/hifiberry-dac-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/hifiberry-dacplus-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/hifiberry-digi-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/hifiberry-digi-pro-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/hy28a-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/hy28b-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i2c-bcm2708-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i2c-gpio-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i2c-mux-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i2c-pwm-pca9685a-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i2c-sensor-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i2c0-bcm2708-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i2c1-bcm2708-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i2s-gpio28-31-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/iqaudio-dac-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/iqaudio-dacplus-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/iqaudio-digi-wm8804-audio-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/justboom-dac-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/justboom-digi-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/lirc-rpi-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/mcp23017-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/mcp23s17-overlay.dts + create mode 100755 arch/arm/boot/dts/overlays/mcp2515-can0-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/mcp2515-can1-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/midi-uart0-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/mmc-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/mz61581-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/pi3-act-led-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/pi3-disable-bt-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/piscreen-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/piscreen2r-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/pisound-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/pitft22-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/pitft28-capacitive-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/pitft28-resistive-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/pitft35-resistive-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/pps-gpio-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/pwm-2chan-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/pwm-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/qca7000-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/raspidac3-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/rpi-backlight-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/rpi-dac-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/rpi-display-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/rpi-ft5406-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/rpi-proto-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/rpi-sense-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/rra-digidac1-wm8741-audio-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/sc16is750-i2c-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/sc16is752-spi1-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/sdhost-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/sdio-1bit-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/sdio-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/sdtweak-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/smi-dev-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/smi-nand-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/smi-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi-gpio35-39-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi-rtc-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi0-hw-cs-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi1-1cs-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi1-2cs-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi1-3cs-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi2-1cs-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi2-2cs-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi2-3cs-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/tinylcd35-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/uart1-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/vc4-fkms-v3d-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/vga666-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/w1-gpio-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/w1-gpio-pullup-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/wittypi-overlay.dts + +--- a/arch/arm/Makefile ++++ b/arch/arm/Makefile +@@ -334,6 +334,8 @@ $(INSTALL_TARGETS): + + %.dtb: | scripts + $(Q)$(MAKE) $(build)=$(boot)/dts MACHINE=$(MACHINE) $(boot)/dts/$@ ++%.dtbo: | scripts ++ $(Q)$(MAKE) $(build)=$(boot)/dts MACHINE=$(MACHINE) $(boot)/dts/$@ + + PHONY += dtbs dtbs_install + +--- a/arch/arm/boot/.gitignore ++++ b/arch/arm/boot/.gitignore +@@ -3,4 +3,4 @@ zImage + xipImage + bootpImage + uImage +-*.dtb ++*.dtb* +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -1,5 +1,13 @@ + ifeq ($(CONFIG_OF),y) + ++dtb-$(CONFIG_ARCH_BCM2835) += \ ++ bcm2708-rpi-b.dtb \ ++ bcm2708-rpi-b-plus.dtb \ ++ bcm2708-rpi-cm.dtb \ ++ bcm2709-rpi-2-b.dtb \ ++ bcm2710-rpi-3-b.dtb \ ++ bcm2710-rpi-cm3.dtb ++ + dtb-$(CONFIG_ARCH_ALPINE) += \ + alpine-db.dtb + dtb-$(CONFIG_MACH_ARTPEC6) += \ +@@ -955,10 +963,21 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \ + dtb-$(CONFIG_ARCH_ZX) += zx296702-ad1.dtb + dtb-$(CONFIG_ARCH_ASPEED) += aspeed-bmc-opp-palmetto.dtb \ + aspeed-ast2500-evb.dtb ++ ++targets += dtbs dtbs_install ++targets += $(dtb-y) ++ + endif + + dtstree := $(srctree)/$(src) + dtb-$(CONFIG_OF_ALL_DTBS) := $(patsubst $(dtstree)/%.dts,%.dtb, $(wildcard $(dtstree)/*.dts)) + + always := $(dtb-y) ++subdir-y := overlays + clean-files := *.dtb ++ ++# Enable fixups to support overlays on BCM2835 platforms ++ifeq ($(CONFIG_ARCH_BCM2835),y) ++ DTC_FLAGS ?= -@ -H epapr ++ dts-dirs += overlays ++endif +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2708-rpi-b-plus.dts +@@ -0,0 +1,156 @@ ++/dts-v1/; ++ ++#include "bcm2708.dtsi" ++ ++/ { ++ model = "Raspberry Pi Model B+"; ++}; ++ ++&gpio { ++ sdhost_pins: sdhost_pins { ++ brcm,pins = <48 49 50 51 52 53>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ spi0_pins: spi0_pins { ++ brcm,pins = <9 10 11>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ spi0_cs_pins: spi0_cs_pins { ++ brcm,pins = <8 7>; ++ brcm,function = <1>; /* output */ ++ }; ++ ++ i2c0_pins: i2c0 { ++ brcm,pins = <0 1>; ++ brcm,function = <4>; ++ }; ++ ++ i2c1_pins: i2c1 { ++ brcm,pins = <2 3>; ++ brcm,function = <4>; ++ }; ++ ++ i2s_pins: i2s { ++ brcm,pins = <18 19 20 21>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ audio_pins: audio_pins { ++ brcm,pins = <40 45>; ++ brcm,function = <4>; ++ }; ++}; ++ ++&sdhost { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sdhost_pins>; ++ bus-width = <4>; ++ status = "okay"; ++}; ++ ++&fb { ++ status = "okay"; ++}; ++ ++&uart0 { ++ status = "okay"; ++}; ++ ++&spi0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi0_pins &spi0_cs_pins>; ++ cs-gpios = <&gpio 8 1>, <&gpio 7 1>; ++ ++ spidev0: spidev@0{ ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ }; ++ ++ spidev1: spidev@1{ ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ }; ++}; ++ ++&i2c0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c0_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2c1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c1_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2c2 { ++ clock-frequency = <100000>; ++}; ++ ++&i2s { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2s_pins>; ++}; ++ ++&leds { ++ act_led: act { ++ label = "led0"; ++ linux,default-trigger = "mmc0"; ++ gpios = <&gpio 47 0>; ++ }; ++ ++ pwr_led: pwr { ++ label = "led1"; ++ linux,default-trigger = "input"; ++ gpios = <&gpio 35 0>; ++ }; ++}; ++ ++&hdmi { ++ hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; ++}; ++ ++&audio { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&audio_pins>; ++}; ++ ++/ { ++ __overrides__ { ++ uart0 = <&uart0>,"status"; ++ uart1 = <&uart1>,"status"; ++ i2s = <&i2s>,"status"; ++ spi = <&spi0>,"status"; ++ i2c0 = <&i2c0>,"status"; ++ i2c1 = <&i2c1>,"status"; ++ i2c2_iknowwhatimdoing = <&i2c2>,"status"; ++ i2c0_baudrate = <&i2c0>,"clock-frequency:0"; ++ i2c1_baudrate = <&i2c1>,"clock-frequency:0"; ++ i2c2_baudrate = <&i2c2>,"clock-frequency:0"; ++ ++ act_led_gpio = <&act_led>,"gpios:4"; ++ act_led_activelow = <&act_led>,"gpios:8"; ++ act_led_trigger = <&act_led>,"linux,default-trigger"; ++ ++ pwr_led_gpio = <&pwr_led>,"gpios:4"; ++ pwr_led_activelow = <&pwr_led>,"gpios:8"; ++ pwr_led_trigger = <&pwr_led>,"linux,default-trigger"; ++ ++ audio = <&audio>,"status"; ++ watchdog = <&watchdog>,"status"; ++ random = <&random>,"status"; ++ sd_overclock = <&sdhost>,"brcm,overclock-50:0"; ++ sd_force_pio = <&sdhost>,"brcm,force-pio?"; ++ sd_pio_limit = <&sdhost>,"brcm,pio-limit:0"; ++ sd_debug = <&sdhost>,"brcm,debug"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2708-rpi-b.dts +@@ -0,0 +1,146 @@ ++/dts-v1/; ++ ++#include "bcm2708.dtsi" ++ ++/ { ++ model = "Raspberry Pi Model B"; ++}; ++ ++&gpio { ++ sdhost_pins: sdhost_pins { ++ brcm,pins = <48 49 50 51 52 53>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ spi0_pins: spi0_pins { ++ brcm,pins = <9 10 11>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ spi0_cs_pins: spi0_cs_pins { ++ brcm,pins = <8 7>; ++ brcm,function = <1>; /* output */ ++ }; ++ ++ i2c0_pins: i2c0 { ++ brcm,pins = <0 1>; ++ brcm,function = <4>; ++ }; ++ ++ i2c1_pins: i2c1 { ++ brcm,pins = <2 3>; ++ brcm,function = <4>; ++ }; ++ ++ i2s_pins: i2s { ++ brcm,pins = <28 29 30 31>; ++ brcm,function = <6>; /* alt2 */ ++ }; ++ ++ audio_pins: audio_pins { ++ brcm,pins = <40 45>; ++ brcm,function = <4>; ++ }; ++}; ++ ++&sdhost { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sdhost_pins>; ++ bus-width = <4>; ++ status = "okay"; ++}; ++ ++&fb { ++ status = "okay"; ++}; ++ ++&uart0 { ++ status = "okay"; ++}; ++ ++&spi0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi0_pins &spi0_cs_pins>; ++ cs-gpios = <&gpio 8 1>, <&gpio 7 1>; ++ ++ spidev0: spidev@0{ ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ }; ++ ++ spidev1: spidev@1{ ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ }; ++}; ++ ++&i2c0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c0_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2c1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c1_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2c2 { ++ clock-frequency = <100000>; ++}; ++ ++&i2s { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2s_pins>; ++}; ++ ++&leds { ++ act_led: act { ++ label = "led0"; ++ linux,default-trigger = "mmc0"; ++ gpios = <&gpio 16 1>; ++ }; ++}; ++ ++&hdmi { ++ hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>; ++}; ++ ++&audio { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&audio_pins>; ++}; ++ ++/ { ++ __overrides__ { ++ uart0 = <&uart0>,"status"; ++ uart1 = <&uart1>,"status"; ++ i2s = <&i2s>,"status"; ++ spi = <&spi0>,"status"; ++ i2c0 = <&i2c0>,"status"; ++ i2c1 = <&i2c1>,"status"; ++ i2c2_iknowwhatimdoing = <&i2c2>,"status"; ++ i2c0_baudrate = <&i2c0>,"clock-frequency:0"; ++ i2c1_baudrate = <&i2c1>,"clock-frequency:0"; ++ i2c2_baudrate = <&i2c2>,"clock-frequency:0"; ++ ++ act_led_gpio = <&act_led>,"gpios:4"; ++ act_led_activelow = <&act_led>,"gpios:8"; ++ act_led_trigger = <&act_led>,"linux,default-trigger"; ++ ++ audio = <&audio>,"status"; ++ watchdog = <&watchdog>,"status"; ++ random = <&random>,"status"; ++ sd_overclock = <&sdhost>,"brcm,overclock-50:0"; ++ sd_force_pio = <&sdhost>,"brcm,force-pio?"; ++ sd_pio_limit = <&sdhost>,"brcm,pio-limit:0"; ++ sd_debug = <&sdhost>,"brcm,debug"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2708-rpi-cm.dts +@@ -0,0 +1,105 @@ ++/dts-v1/; ++ ++#include "bcm2708-rpi-cm.dtsi" ++ ++/ { ++ model = "Raspberry Pi Compute Module"; ++}; ++ ++&uart0 { ++ status = "okay"; ++}; ++ ++&gpio { ++ spi0_pins: spi0_pins { ++ brcm,pins = <9 10 11>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ spi0_cs_pins: spi0_cs_pins { ++ brcm,pins = <8 7>; ++ brcm,function = <1>; /* output */ ++ }; ++ ++ i2c0_pins: i2c0 { ++ brcm,pins = <0 1>; ++ brcm,function = <4>; ++ }; ++ ++ i2c1_pins: i2c1 { ++ brcm,pins = <2 3>; ++ brcm,function = <4>; ++ }; ++ ++ i2s_pins: i2s { ++ brcm,pins = <18 19 20 21>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ audio_pins: audio_pins { ++ brcm,pins; ++ brcm,function; ++ }; ++}; ++ ++&spi0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi0_pins &spi0_cs_pins>; ++ cs-gpios = <&gpio 8 1>, <&gpio 7 1>; ++ ++ spidev0: spidev@0{ ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ }; ++ ++ spidev1: spidev@1{ ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ }; ++}; ++ ++&i2c0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c0_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2c1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c1_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2c2 { ++ clock-frequency = <100000>; ++}; ++ ++&i2s { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2s_pins>; ++}; ++ ++&hdmi { ++ hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>; ++}; ++ ++/ { ++ __overrides__ { ++ uart0 = <&uart0>,"status"; ++ uart1 = <&uart1>,"status"; ++ i2s = <&i2s>,"status"; ++ spi = <&spi0>,"status"; ++ i2c0 = <&i2c0>,"status"; ++ i2c1 = <&i2c1>,"status"; ++ i2c2_iknowwhatimdoing = <&i2c2>,"status"; ++ i2c0_baudrate = <&i2c0>,"clock-frequency:0"; ++ i2c1_baudrate = <&i2c1>,"clock-frequency:0"; ++ i2c2_baudrate = <&i2c2>,"clock-frequency:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2708-rpi-cm.dtsi +@@ -0,0 +1,50 @@ ++#include "bcm2708.dtsi" ++ ++&gpio { ++ sdhost_pins: sdhost_pins { ++ brcm,pins = <48 49 50 51 52 53>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++}; ++ ++&gpio { ++ mmc_pins: mmc_pins { ++ brcm,pins = <48 49 50 51 52 53>; ++ brcm,function = <7>; /* alt3 */ ++ }; ++}; ++ ++&leds { ++ act_led: act { ++ label = "led0"; ++ linux,default-trigger = "mmc0"; ++ gpios = <&gpio 47 0>; ++ }; ++}; ++ ++ ++&sdhost { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sdhost_pins>; ++ non-removable; ++ bus-width = <4>; ++ status = "okay"; ++ brcm,overclock-50 = <0>; ++}; ++ ++&fb { ++ status = "okay"; ++}; ++ ++/ { ++ __overrides__ { ++ act_led_gpio = <&act_led>,"gpios:4"; ++ act_led_activelow = <&act_led>,"gpios:8"; ++ act_led_trigger = <&act_led>,"linux,default-trigger"; ++ ++ audio = <&audio>,"status"; ++ watchdog = <&watchdog>,"status"; ++ random = <&random>,"status"; ++ sd_overclock = <&mmc>,"brcm,overclock-50:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2708-rpi.dtsi +@@ -0,0 +1,109 @@ ++/* Downstream version of bcm2835-rpi.dtsi */ ++ ++#include ++ ++/ { ++ memory { ++ device_type = "memory"; ++ reg = <0x0 0x0>; ++ }; ++ ++ aliases { ++ audio = &audio; ++ aux = &aux; ++ sound = &sound; ++ soc = &soc; ++ dma = &dma; ++ intc = &intc; ++ watchdog = &watchdog; ++ random = &random; ++ mailbox = &mailbox; ++ gpio = &gpio; ++ uart0 = &uart0; ++ sdhost = &sdhost; ++ i2s = &i2s; ++ spi0 = &spi0; ++ i2c0 = &i2c0; ++ uart1 = &uart1; ++ spi1 = &spi1; ++ spi2 = &spi2; ++ mmc = &mmc; ++ i2c1 = &i2c1; ++ i2c2 = &i2c2; ++ usb = &usb; ++ leds = &leds; ++ fb = &fb; ++ vchiq = &vchiq; ++ thermal = &thermal; ++ }; ++ ++ leds: leds { ++ compatible = "gpio-leds"; ++ }; ++ ++ soc { ++ gpiomem { ++ compatible = "brcm,bcm2835-gpiomem"; ++ reg = <0x7e200000 0x1000>; ++ }; ++ ++ firmware: firmware { ++ compatible = "raspberrypi,bcm2835-firmware"; ++ mboxes = <&mailbox>; ++ }; ++ ++ power: power { ++ compatible = "raspberrypi,bcm2835-power"; ++ firmware = <&firmware>; ++ #power-domain-cells = <1>; ++ }; ++ ++ fb: fb { ++ compatible = "brcm,bcm2708-fb"; ++ firmware = <&firmware>; ++ status = "disabled"; ++ }; ++ ++ vchiq: vchiq { ++ compatible = "brcm,bcm2835-vchiq"; ++ reg = <0x7e00b840 0xf>; ++ interrupts = <0 2>; ++ cache-line-size = <32>; ++ firmware = <&firmware>; ++ }; ++ ++ thermal: thermal { ++ compatible = "brcm,bcm2835-thermal"; ++ firmware = <&firmware>; ++ }; ++ ++ /* Onboard audio */ ++ audio: audio { ++ compatible = "brcm,bcm2835-audio"; ++ brcm,pwm-channels = <8>; ++ status = "disabled"; ++ }; ++ ++ /* External sound card */ ++ sound: sound { ++ status = "disabled"; ++ }; ++ ++ }; ++ ++ __overrides__ { ++ cache_line_size = <&vchiq>, "cache-line-size:0"; ++ }; ++}; ++ ++&dma { ++ brcm,dma-channel-mask = <0x7f34>; ++}; ++ ++&hdmi { ++ power-domains = <&power RPI_POWER_DOMAIN_HDMI>; ++}; ++ ++&usb { ++ power-domains = <&power RPI_POWER_DOMAIN_USB>; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2708.dtsi +@@ -0,0 +1,16 @@ ++#include "bcm2835.dtsi" ++#include "bcm270x.dtsi" ++#include "bcm2708-rpi.dtsi" ++ ++/ { ++ soc { ++ timer@7e003000 { ++ compatible = "brcm,bcm2835-system-timer"; ++ reg = <0x7e003000 0x1000>; ++ interrupts = <1 0>, <1 1>, <1 2>, <1 3>; ++ clock-frequency = <1000000>; ++ }; ++ }; ++ ++ /delete-node/ cpus; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2709-rpi-2-b.dts +@@ -0,0 +1,156 @@ ++/dts-v1/; ++ ++#include "bcm2709.dtsi" ++ ++/ { ++ model = "Raspberry Pi 2 Model B"; ++}; ++ ++&gpio { ++ sdhost_pins: sdhost_pins { ++ brcm,pins = <48 49 50 51 52 53>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ spi0_pins: spi0_pins { ++ brcm,pins = <9 10 11>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ spi0_cs_pins: spi0_cs_pins { ++ brcm,pins = <8 7>; ++ brcm,function = <1>; /* output */ ++ }; ++ ++ i2c0_pins: i2c0 { ++ brcm,pins = <0 1>; ++ brcm,function = <4>; ++ }; ++ ++ i2c1_pins: i2c1 { ++ brcm,pins = <2 3>; ++ brcm,function = <4>; ++ }; ++ ++ i2s_pins: i2s { ++ brcm,pins = <18 19 20 21>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ audio_pins: audio_pins { ++ brcm,pins = <40 45>; ++ brcm,function = <4>; ++ }; ++}; ++ ++&sdhost { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sdhost_pins>; ++ bus-width = <4>; ++ status = "okay"; ++}; ++ ++&fb { ++ status = "okay"; ++}; ++ ++&uart0 { ++ status = "okay"; ++}; ++ ++&spi0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi0_pins &spi0_cs_pins>; ++ cs-gpios = <&gpio 8 1>, <&gpio 7 1>; ++ ++ spidev0: spidev@0{ ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ }; ++ ++ spidev1: spidev@1{ ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ }; ++}; ++ ++&i2c0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c0_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2c1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c1_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2c2 { ++ clock-frequency = <100000>; ++}; ++ ++&i2s { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2s_pins>; ++}; ++ ++&leds { ++ act_led: act { ++ label = "led0"; ++ linux,default-trigger = "mmc0"; ++ gpios = <&gpio 47 0>; ++ }; ++ ++ pwr_led: pwr { ++ label = "led1"; ++ linux,default-trigger = "input"; ++ gpios = <&gpio 35 0>; ++ }; ++}; ++ ++&hdmi { ++ hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; ++}; ++ ++&audio { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&audio_pins>; ++}; ++ ++/ { ++ __overrides__ { ++ uart0 = <&uart0>,"status"; ++ uart1 = <&uart1>,"status"; ++ i2s = <&i2s>,"status"; ++ spi = <&spi0>,"status"; ++ i2c0 = <&i2c0>,"status"; ++ i2c1 = <&i2c1>,"status"; ++ i2c2_iknowwhatimdoing = <&i2c2>,"status"; ++ i2c0_baudrate = <&i2c0>,"clock-frequency:0"; ++ i2c1_baudrate = <&i2c1>,"clock-frequency:0"; ++ i2c2_baudrate = <&i2c2>,"clock-frequency:0"; ++ ++ act_led_gpio = <&act_led>,"gpios:4"; ++ act_led_activelow = <&act_led>,"gpios:8"; ++ act_led_trigger = <&act_led>,"linux,default-trigger"; ++ ++ pwr_led_gpio = <&pwr_led>,"gpios:4"; ++ pwr_led_activelow = <&pwr_led>,"gpios:8"; ++ pwr_led_trigger = <&pwr_led>,"linux,default-trigger"; ++ ++ audio = <&audio>,"status"; ++ watchdog = <&watchdog>,"status"; ++ random = <&random>,"status"; ++ sd_overclock = <&sdhost>,"brcm,overclock-50:0"; ++ sd_force_pio = <&sdhost>,"brcm,force-pio?"; ++ sd_pio_limit = <&sdhost>,"brcm,pio-limit:0"; ++ sd_debug = <&sdhost>,"brcm,debug"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2709.dtsi +@@ -0,0 +1,22 @@ ++#include "bcm2836.dtsi" ++#include "bcm270x.dtsi" ++#include "bcm2708-rpi.dtsi" ++ ++/ { ++ soc { ++ ranges = <0x7e000000 0x3f000000 0x01000000>, ++ <0x40000000 0x40000000 0x00040000>; ++ ++ syscon@40000000 { ++ compatible = "brcm,bcm2836-arm-local", "syscon"; ++ reg = <0x40000000 0x100>; ++ }; ++ }; ++ ++ __overrides__ { ++ arm_freq = <&v7_cpu0>, "clock-frequency:0", ++ <&v7_cpu1>, "clock-frequency:0", ++ <&v7_cpu2>, "clock-frequency:0", ++ <&v7_cpu3>, "clock-frequency:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/bcm270x.dtsi +@@ -0,0 +1,141 @@ ++/* Downstream bcm283x.dtsi diff */ ++#include "dt-bindings/power/raspberrypi-power.h" ++ ++/ { ++ chosen { ++ bootargs = ""; ++ }; ++ ++ soc: soc { ++ ++ /delete-node/ timer@7e003000; ++ ++ watchdog: watchdog@7e100000 { ++ /* Add alias */ ++ }; ++ ++ cprman: cprman@7e101000 { ++ /* Add alias */ ++ }; ++ ++ random: rng@7e104000 { ++ /* Add alias */ ++ }; ++ ++ gpio@7e200000 { /* gpio */ ++ interrupts = <2 17>, <2 18>; ++ }; ++ ++ sdhost: sdhost@7e202000 { ++ compatible = "brcm,bcm2835-sdhost"; ++ reg = <0x7e202000 0x100>; ++ interrupts = <2 24>; ++ clocks = <&clocks BCM2835_CLOCK_VPU>; ++ dmas = <&dma 13>; ++ dma-names = "rx-tx"; ++ brcm,overclock-50 = <0>; ++ brcm,pio-limit = <1>; ++ status = "disabled"; ++ }; ++ ++ i2s@7e203000 { /* i2s */ ++ #sound-dai-cells = <0>; ++ reg = <0x7e203000 0x24>; ++ clocks = <&clocks BCM2835_CLOCK_PCM>; ++ }; ++ ++ spi0: spi@7e204000 { ++ /* Add alias */ ++ dmas = <&dma 6>, <&dma 7>; ++ dma-names = "tx", "rx"; ++ }; ++ ++ pixelvalve0: pixelvalve@7e206000 { ++ /* Add alias */ ++ status = "disabled"; ++ }; ++ ++ pixelvalve1: pixelvalve@7e207000 { ++ /* Add alias */ ++ status = "disabled"; ++ }; ++ ++ dpi: dpi@7e208000 { ++ compatible = "brcm,bcm2835-dpi"; ++ reg = <0x7e208000 0x8c>; ++ clocks = <&clocks BCM2835_CLOCK_VPU>, ++ <&clocks BCM2835_CLOCK_DPI>; ++ clock-names = "core", "pixel"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "disabled"; ++ }; ++ ++ /delete-node/ sdhci@7e300000; ++ ++ mmc: mmc@7e300000 { ++ compatible = "brcm,bcm2835-mmc"; ++ reg = <0x7e300000 0x100>; ++ interrupts = <2 30>; ++ clocks = <&clocks BCM2835_CLOCK_EMMC>; ++ dmas = <&dma 11>; ++ dma-names = "rx-tx"; ++ brcm,overclock-50 = <0>; ++ status = "disabled"; ++ }; ++ ++ hvs: hvs@7e400000 { ++ /* Add alias */ ++ status = "disabled"; ++ }; ++ ++ firmwarekms: firmwarekms@7e600000 { ++ compatible = "raspberrypi,rpi-firmware-kms"; ++ /* SMI interrupt reg */ ++ reg = <0x7e600000 0x100>; ++ interrupts = <2 16>; ++ brcm,firmware = <&firmware>; ++ status = "disabled"; ++ }; ++ ++ smi: smi@7e600000 { ++ compatible = "brcm,bcm2835-smi"; ++ reg = <0x7e600000 0x100>; ++ interrupts = <2 16>; ++ clocks = <&clocks BCM2835_CLOCK_SMI>; ++ assigned-clocks = <&cprman BCM2835_CLOCK_SMI>; ++ assigned-clock-rates = <125000000>; ++ dmas = <&dma 4>; ++ dma-names = "rx-tx"; ++ status = "disabled"; ++ }; ++ ++ pixelvalve2: pixelvalve@7e807000 { ++ /* Add alias */ ++ status = "disabled"; ++ }; ++ ++ hdmi@7e902000 { /* hdmi */ ++ status = "disabled"; ++ }; ++ ++ usb@7e980000 { /* usb */ ++ compatible = "brcm,bcm2708-usb"; ++ reg = <0x7e980000 0x10000>, ++ <0x7e006000 0x1000>; ++ interrupts = <2 0>, ++ <1 9>; ++ }; ++ ++ v3d@7ec00000 { /* vd3 */ ++ compatible = "brcm,vc4-v3d"; ++ power-domains = <&power RPI_POWER_DOMAIN_V3D>; ++ status = "disabled"; ++ }; ++ ++ gpu: gpu { ++ /* Add alias */ ++ status = "disabled"; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2710-rpi-3-b.dts +@@ -0,0 +1,203 @@ ++/dts-v1/; ++ ++#ifdef RPI364 ++/memreserve/ 0x00000000 0x00001000; ++#endif ++ ++#include "bcm2710.dtsi" ++ ++/ { ++ model = "Raspberry Pi 3 Model B"; ++}; ++ ++&gpio { ++ sdhost_pins: sdhost_pins { ++ brcm,pins = <48 49 50 51 52 53>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ spi0_pins: spi0_pins { ++ brcm,pins = <9 10 11>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ spi0_cs_pins: spi0_cs_pins { ++ brcm,pins = <8 7>; ++ brcm,function = <1>; /* output */ ++ }; ++ ++ i2c0_pins: i2c0 { ++ brcm,pins = <0 1>; ++ brcm,function = <4>; ++ }; ++ ++ i2c1_pins: i2c1 { ++ brcm,pins = <2 3>; ++ brcm,function = <4>; ++ }; ++ ++ i2s_pins: i2s { ++ brcm,pins = <18 19 20 21>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ sdio_pins: sdio_pins { ++ brcm,pins = <34 35 36 37 38 39>; ++ brcm,function = <7>; // alt3 = SD1 ++ brcm,pull = <0 2 2 2 2 2>; ++ }; ++ ++ bt_pins: bt_pins { ++ brcm,pins = <43>; ++ brcm,function = <4>; /* alt0:GPCLK2 */ ++ brcm,pull = <0>; ++ }; ++ ++ uart0_pins: uart0_pins { ++ brcm,pins = <32 33>; ++ brcm,function = <7>; /* alt3=UART0 */ ++ brcm,pull = <0 2>; ++ }; ++ ++ uart1_pins: uart1_pins { ++ brcm,pins; ++ brcm,function; ++ brcm,pull; ++ }; ++ ++ audio_pins: audio_pins { ++ brcm,pins = <40 41>; ++ brcm,function = <4>; ++ }; ++}; ++ ++&sdhost { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sdhost_pins>; ++ bus-width = <4>; ++ status = "okay"; ++}; ++ ++&mmc { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sdio_pins>; ++ non-removable; ++ bus-width = <4>; ++ status = "okay"; ++ brcm,overclock-50 = <0>; ++}; ++ ++&soc { ++ virtgpio: virtgpio { ++ compatible = "brcm,bcm2835-virtgpio"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ firmware = <&firmware>; ++ status = "okay"; ++ }; ++}; ++ ++&fb { ++ status = "okay"; ++}; ++ ++&uart0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart0_pins &bt_pins>; ++ status = "okay"; ++}; ++ ++&uart1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart1_pins>; ++ status = "okay"; ++}; ++ ++&spi0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi0_pins &spi0_cs_pins>; ++ cs-gpios = <&gpio 8 1>, <&gpio 7 1>; ++ ++ spidev0: spidev@0{ ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ }; ++ ++ spidev1: spidev@1{ ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ }; ++}; ++ ++&i2c0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c0_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2c1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c1_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2c2 { ++ clock-frequency = <100000>; ++}; ++ ++&i2s { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2s_pins>; ++}; ++ ++&leds { ++ act_led: act { ++ label = "led0"; ++ linux,default-trigger = "mmc0"; ++ gpios = <&virtgpio 0 0>; ++ }; ++}; ++ ++&audio { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&audio_pins>; ++}; ++ ++/ { ++ chosen { ++ bootargs = "8250.nr_uarts=1"; ++ }; ++}; ++ ++/ { ++ __overrides__ { ++ uart0 = <&uart0>,"status"; ++ uart1 = <&uart1>,"status"; ++ i2s = <&i2s>,"status"; ++ spi = <&spi0>,"status"; ++ i2c0 = <&i2c0>,"status"; ++ i2c1 = <&i2c1>,"status"; ++ i2c2_iknowwhatimdoing = <&i2c2>,"status"; ++ i2c0_baudrate = <&i2c0>,"clock-frequency:0"; ++ i2c1_baudrate = <&i2c1>,"clock-frequency:0"; ++ i2c2_baudrate = <&i2c2>,"clock-frequency:0"; ++ ++ act_led_gpio = <&act_led>,"gpios:4"; ++ act_led_activelow = <&act_led>,"gpios:8"; ++ act_led_trigger = <&act_led>,"linux,default-trigger"; ++ ++ audio = <&audio>,"status"; ++ watchdog = <&watchdog>,"status"; ++ random = <&random>,"status"; ++ sd_overclock = <&sdhost>,"brcm,overclock-50:0"; ++ sd_force_pio = <&sdhost>,"brcm,force-pio?"; ++ sd_pio_limit = <&sdhost>,"brcm,pio-limit:0"; ++ sd_debug = <&sdhost>,"brcm,debug"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2710-rpi-cm3.dts +@@ -0,0 +1,155 @@ ++/dts-v1/; ++ ++#include "bcm2710.dtsi" ++ ++/ { ++ model = "Raspberry Pi Compute Module 3"; ++}; ++ ++&gpio { ++ sdhost_pins: sdhost_pins { ++ brcm,pins = <48 49 50 51 52 53>; ++ brcm,function = <4>; /* alt0 */ ++ brcm,pull = <0 2 2 2 2 2>; ++ }; ++ ++ spi0_pins: spi0_pins { ++ brcm,pins = <9 10 11>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ spi0_cs_pins: spi0_cs_pins { ++ brcm,pins = <8 7>; ++ brcm,function = <1>; /* output */ ++ }; ++ ++ i2c0_pins: i2c0 { ++ brcm,pins = <0 1>; ++ brcm,function = <4>; ++ }; ++ ++ i2c1_pins: i2c1 { ++ brcm,pins = <2 3>; ++ brcm,function = <4>; ++ }; ++ ++ i2s_pins: i2s { ++ brcm,pins = <18 19 20 21>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ audio_pins: audio_pins { ++ brcm,pins; ++ brcm,function; ++ }; ++}; ++ ++&sdhost { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sdhost_pins>; ++ non-removable; ++ bus-width = <4>; ++ status = "okay"; ++ brcm,overclock-50 = <0>; ++}; ++ ++&soc { ++ virtgpio: virtgpio { ++ compatible = "brcm,bcm2835-virtgpio"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ firmware = <&firmware>; ++ status = "okay"; ++ }; ++}; ++ ++&fb { ++ status = "okay"; ++}; ++ ++&spi0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi0_pins &spi0_cs_pins>; ++ cs-gpios = <&gpio 8 1>, <&gpio 7 1>; ++ ++ spidev0: spidev@0{ ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ }; ++ ++ spidev1: spidev@1{ ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ }; ++}; ++ ++&i2c0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c0_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2c1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c1_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2c2 { ++ clock-frequency = <100000>; ++}; ++ ++&i2s { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2s_pins>; ++}; ++ ++&leds { ++ act_led: act { ++ label = "led0"; ++ linux,default-trigger = "mmc0"; ++ gpios = <&virtgpio 0 0>; ++ }; ++}; ++ ++&hdmi { ++ hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; ++}; ++ ++&audio { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&audio_pins>; ++}; ++ ++/ { ++ __overrides__ { ++ uart0 = <&uart0>,"status"; ++ uart1 = <&uart1>,"status"; ++ i2s = <&i2s>,"status"; ++ spi = <&spi0>,"status"; ++ i2c0 = <&i2c0>,"status"; ++ i2c1 = <&i2c1>,"status"; ++ i2c2_iknowwhatimdoing = <&i2c2>,"status"; ++ i2c0_baudrate = <&i2c0>,"clock-frequency:0"; ++ i2c1_baudrate = <&i2c1>,"clock-frequency:0"; ++ i2c2_baudrate = <&i2c2>,"clock-frequency:0"; ++ ++ act_led_gpio = <&act_led>,"gpios:4"; ++ act_led_activelow = <&act_led>,"gpios:8"; ++ act_led_trigger = <&act_led>,"linux,default-trigger"; ++ ++ audio = <&audio>,"status"; ++ watchdog = <&watchdog>,"status"; ++ random = <&random>,"status"; ++ sd_overclock = <&sdhost>,"brcm,overclock-50:0"; ++ sd_force_pio = <&sdhost>,"brcm,force-pio?"; ++ sd_pio_limit = <&sdhost>,"brcm,pio-limit:0"; ++ sd_debug = <&sdhost>,"brcm,debug"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2710.dtsi +@@ -0,0 +1,155 @@ ++#include "bcm283x.dtsi" ++#include "bcm270x.dtsi" ++#include "bcm2708-rpi.dtsi" ++ ++/ { ++ compatible = "brcm,bcm2837", "brcm,bcm2836"; ++ model = "BCM2837"; ++ ++ soc { ++ ranges = <0x7e000000 0x3f000000 0x01000000>, ++ <0x40000000 0x40000000 0x00040000>; ++ dma-ranges = <0xc0000000 0x00000000 0x3f000000>; ++ ++ local_intc: local_intc { ++ compatible = "brcm,bcm2836-l1-intc"; ++ reg = <0x40000000 0x100>; ++ interrupt-controller; ++ #interrupt-cells = <1>; ++ interrupt-parent = <&local_intc>; ++ }; ++ ++ arm-pmu { ++#ifdef RPI364 ++ compatible = "arm,armv8-pmuv3", "arm,cortex-a7-pmu"; ++#else ++ compatible = "arm,cortex-a7-pmu"; ++#endif ++ interrupt-parent = <&local_intc>; ++ interrupts = <9>; ++ }; ++ ++ timer { ++#ifdef RPI364 ++ compatible = "arm,armv8-timer", "arm,armv7-timer"; ++#else ++ compatible = "arm,armv7-timer"; ++#endif ++ interrupt-parent = <&local_intc>; ++ interrupts = <0>, // PHYS_SECURE_PPI ++ <1>, // PHYS_NONSECURE_PPI ++ <3>, // VIRT_PPI ++ <2>; // HYP_PPI ++ always-on; ++ }; ++ ++ syscon@40000000 { ++ compatible = "brcm,bcm2836-arm-local", "syscon"; ++ reg = <0x40000000 0x100>; ++ }; ++ }; ++ ++#ifdef RPI364 ++ cpus: cpus { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ v8_cpu0: cpu@0 { ++ device_type = "cpu"; ++ compatible = "arm,cortex-a53", "arm,armv8"; ++ reg = <0x0>; ++ clock-frequency = <1200000000>; ++ }; ++ ++ v8_cpu1: cpu@1 { ++ device_type = "cpu"; ++ compatible = "arm,cortex-a53", "arm,armv8"; ++ reg = <0x1>; ++ clock-frequency = <1200000000>; ++ enable-method = "spin-table"; ++ cpu-release-addr = <0x0 0x000000e0>; ++ }; ++ ++ v8_cpu2: cpu@2 { ++ device_type = "cpu"; ++ compatible = "arm,cortex-a53", "arm,armv8"; ++ reg = <0x2>; ++ clock-frequency = <1200000000>; ++ enable-method = "spin-table"; ++ cpu-release-addr = <0x0 0x000000e8>; ++ }; ++ ++ v8_cpu3: cpu@3 { ++ device_type = "cpu"; ++ compatible = "arm,cortex-a53", "arm,armv8"; ++ reg = <0x3>; ++ clock-frequency = <1200000000>; ++ enable-method = "spin-table"; ++ cpu-release-addr = <0x0 0x000000f0>; ++ }; ++ }; ++ ++ __overrides__ { ++ arm_freq = <&v8_cpu0>, "clock-frequency:0", ++ <&v8_cpu1>, "clock-frequency:0", ++ <&v8_cpu2>, "clock-frequency:0", ++ <&v8_cpu3>, "clock-frequency:0"; ++ }; ++ ++#else ++ cpus: cpus { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ v7_cpu0: cpu@0 { ++ device_type = "cpu"; ++ compatible = "arm,cortex-a7"; ++ reg = <0x000>; ++ clock-frequency = <800000000>; ++ }; ++ ++ v7_cpu1: cpu@1 { ++ device_type = "cpu"; ++ compatible = "arm,cortex-a7"; ++ reg = <0x001>; ++ clock-frequency = <800000000>; ++ }; ++ ++ v7_cpu2: cpu@2 { ++ device_type = "cpu"; ++ compatible = "arm,cortex-a7"; ++ reg = <0x002>; ++ clock-frequency = <800000000>; ++ }; ++ ++ v7_cpu3: cpu@3 { ++ device_type = "cpu"; ++ compatible = "arm,cortex-a7"; ++ reg = <0x003>; ++ clock-frequency = <800000000>; ++ }; ++ }; ++ ++ __overrides__ { ++ arm_freq = <&v7_cpu0>, "clock-frequency:0", ++ <&v7_cpu1>, "clock-frequency:0", ++ <&v7_cpu2>, "clock-frequency:0", ++ <&v7_cpu3>, "clock-frequency:0"; ++ }; ++#endif ++}; ++ ++&intc { ++ compatible = "brcm,bcm2836-armctrl-ic"; ++ reg = <0x7e00b200 0x200>; ++ interrupt-parent = <&local_intc>; ++ interrupts = <8>; ++}; ++ ++#ifdef RPI364 ++&usb { ++ compatible = "brcm,bcm2835-usb"; ++ reg = <0x7e980000 0x10000>; ++ interrupts = <1 9>; ++}; ++#endif +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/Makefile +@@ -0,0 +1,105 @@ ++# Overlays for the Raspberry Pi platform ++ ++dtbo-$(CONFIG_ARCH_BCM2835) += \ ++ adau1977-adc.dtbo \ ++ ads1015.dtbo \ ++ ads7846.dtbo \ ++ akkordion-iqdacplus.dtbo \ ++ allo-piano-dac-pcm512x-audio.dtbo \ ++ at86rf233.dtbo \ ++ audioinjector-wm8731-audio.dtbo \ ++ audremap.dtbo \ ++ bmp085_i2c-sensor.dtbo \ ++ dht11.dtbo \ ++ dionaudio-loco.dtbo \ ++ dpi18.dtbo \ ++ dpi24.dtbo \ ++ dwc-otg.dtbo \ ++ dwc2.dtbo \ ++ enc28j60.dtbo \ ++ enc28j60-spi2.dtbo \ ++ gpio-ir.dtbo \ ++ gpio-poweroff.dtbo \ ++ hifiberry-amp.dtbo \ ++ hifiberry-dac.dtbo \ ++ hifiberry-dacplus.dtbo \ ++ hifiberry-digi.dtbo \ ++ hifiberry-digi-pro.dtbo \ ++ hy28a.dtbo \ ++ hy28b.dtbo \ ++ i2c-bcm2708.dtbo \ ++ i2c-gpio.dtbo \ ++ i2c-mux.dtbo \ ++ i2c-pwm-pca9685a.dtbo \ ++ i2c-rtc.dtbo \ ++ i2c-sensor.dtbo \ ++ i2c0-bcm2708.dtbo \ ++ i2c1-bcm2708.dtbo \ ++ i2s-gpio28-31.dtbo \ ++ iqaudio-dac.dtbo \ ++ iqaudio-dacplus.dtbo \ ++ iqaudio-digi-wm8804-audio.dtbo \ ++ justboom-dac.dtbo \ ++ justboom-digi.dtbo \ ++ lirc-rpi.dtbo \ ++ mcp23017.dtbo \ ++ mcp23s17.dtbo \ ++ mcp2515-can0.dtbo \ ++ mcp2515-can1.dtbo \ ++ midi-uart0.dtbo \ ++ mmc.dtbo \ ++ mz61581.dtbo \ ++ pi3-act-led.dtbo \ ++ pi3-disable-bt.dtbo \ ++ pi3-miniuart-bt.dtbo \ ++ piscreen.dtbo \ ++ piscreen2r.dtbo \ ++ pisound.dtbo \ ++ pitft22.dtbo \ ++ pitft28-capacitive.dtbo \ ++ pitft28-resistive.dtbo \ ++ pitft35-resistive.dtbo \ ++ pps-gpio.dtbo \ ++ pwm.dtbo \ ++ pwm-2chan.dtbo \ ++ qca7000.dtbo \ ++ raspidac3.dtbo \ ++ rpi-backlight.dtbo \ ++ rpi-dac.dtbo \ ++ rpi-display.dtbo \ ++ rpi-ft5406.dtbo \ ++ rpi-proto.dtbo \ ++ rpi-sense.dtbo \ ++ rra-digidac1-wm8741-audio.dtbo \ ++ sc16is750-i2c.dtbo \ ++ sc16is752-spi1.dtbo \ ++ sdhost.dtbo \ ++ sdio.dtbo \ ++ sdio-1bit.dtbo \ ++ sdtweak.dtbo \ ++ smi.dtbo \ ++ smi-dev.dtbo \ ++ smi-nand.dtbo \ ++ spi-gpio35-39.dtbo \ ++ spi-rtc.dtbo \ ++ spi0-hw-cs.dtbo \ ++ spi1-1cs.dtbo \ ++ spi1-2cs.dtbo \ ++ spi1-3cs.dtbo \ ++ spi2-1cs.dtbo \ ++ spi2-2cs.dtbo \ ++ spi2-3cs.dtbo \ ++ tinylcd35.dtbo \ ++ uart1.dtbo \ ++ vc4-fkms-v3d.dtbo \ ++ vc4-kms-v3d.dtbo \ ++ vga666.dtbo \ ++ w1-gpio.dtbo \ ++ w1-gpio-pullup.dtbo \ ++ wittypi.dtbo ++ ++targets += dtbs dtbs_install ++targets += $(dtbo-y) ++ ++always := $(dtbo-y) ++clean-files := *.dtbo +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/README +@@ -0,0 +1,1368 @@ ++Introduction ++============ ++ ++This directory contains Device Tree overlays. Device Tree makes it possible ++to support many hardware configurations with a single kernel and without the ++need to explicitly load or blacklist kernel modules. Note that this isn't a ++"pure" Device Tree configuration (c.f. MACH_BCM2835) - some on-board devices ++are still configured by the board support code, but the intention is to ++eventually reach that goal. ++ ++On Raspberry Pi, Device Tree usage is controlled from /boot/config.txt. By ++default, the Raspberry Pi kernel boots with device tree enabled. You can ++completely disable DT usage (for now) by adding: ++ ++ device_tree= ++ ++to your config.txt, which should cause your Pi to revert to the old way of ++doing things after a reboot. ++ ++In /boot you will find a .dtb for each base platform. This describes the ++hardware that is part of the Raspberry Pi board. The loader (start.elf and its ++siblings) selects the .dtb file appropriate for the platform by name, and reads ++it into memory. At this point, all of the optional interfaces (i2c, i2s, spi) ++are disabled, but they can be enabled using Device Tree parameters: ++ ++ dtparam=i2c=on,i2s=on,spi=on ++ ++However, this shouldn't be necessary in many use cases because loading an ++overlay that requires one of those interfaces will cause it to be enabled ++automatically, and it is advisable to only enable interfaces if they are ++needed. ++ ++Configuring additional, optional hardware is done using Device Tree overlays ++(see below). ++ ++raspi-config ++============ ++ ++The Advanced Options section of the raspi-config utility can enable and disable ++Device Tree use, as well as toggling the I2C and SPI interfaces. Note that it ++is possible to both enable an interface and blacklist the driver, if for some ++reason you should want to defer the loading. ++ ++Modules ++======= ++ ++As well as describing the hardware, Device Tree also gives enough information ++to allow suitable driver modules to be located and loaded, with the corollary ++that unneeded modules are not loaded. As a result it should be possible to ++remove lines from /etc/modules, and /etc/modprobe.d/raspi-blacklist.conf can ++have its contents deleted (or commented out). ++ ++Using Overlays ++============== ++ ++Overlays are loaded using the "dtoverlay" directive. As an example, consider ++the popular lirc-rpi module, the Linux Infrared Remote Control driver. In the ++pre-DT world this would be loaded from /etc/modules, with an explicit ++"modprobe lirc-rpi" command, or programmatically by lircd. With DT enabled, ++this becomes a line in config.txt: ++ ++ dtoverlay=lirc-rpi ++ ++This causes the file /boot/overlays/lirc-rpi.dtbo to be loaded. By ++default it will use GPIOs 17 (out) and 18 (in), but this can be modified using ++DT parameters: ++ ++ dtoverlay=lirc-rpi,gpio_out_pin=17,gpio_in_pin=13 ++ ++Parameters always have default values, although in some cases (e.g. "w1-gpio") ++it is necessary to provided multiple overlays in order to get the desired ++behaviour. See the list of overlays below for a description of the parameters ++and their defaults. ++ ++The Overlay and Parameter Reference ++=================================== ++ ++N.B. When editing this file, please preserve the indentation levels to make it ++simple to parse programmatically. NO HARD TABS. ++ ++ ++Name: ++Info: Configures the base Raspberry Pi hardware ++Load: ++Params: ++ audio Set to "on" to enable the onboard ALSA audio ++ interface (default "off") ++ ++ i2c_arm Set to "on" to enable the ARM's i2c interface ++ (default "off") ++ ++ i2c_vc Set to "on" to enable the i2c interface ++ usually reserved for the VideoCore processor ++ (default "off") ++ ++ i2c An alias for i2c_arm ++ ++ i2c_arm_baudrate Set the baudrate of the ARM's i2c interface ++ (default "100000") ++ ++ i2c_vc_baudrate Set the baudrate of the VideoCore i2c interface ++ (default "100000") ++ ++ i2c_baudrate An alias for i2c_arm_baudrate ++ ++ i2s Set to "on" to enable the i2s interface ++ (default "off") ++ ++ spi Set to "on" to enable the spi interfaces ++ (default "off") ++ ++ random Set to "on" to enable the hardware random ++ number generator (default "on") ++ ++ sd_overclock Clock (in MHz) to use when the MMC framework ++ requests 50MHz ++ ++ sd_force_pio Disable DMA support for SD driver (default off) ++ ++ sd_pio_limit Number of blocks above which to use DMA for ++ SD card (default 1) ++ ++ sd_debug Enable debug output from SD driver (default off) ++ ++ uart0 Set to "off" to disable uart0 (default "on") ++ ++ uart1 Set to "on" or "off" to enable or disable uart1 ++ (default varies) ++ ++ watchdog Set to "on" to enable the hardware watchdog ++ (default "off") ++ ++ act_led_trigger Choose which activity the LED tracks. ++ Use "heartbeat" for a nice load indicator. ++ (default "mmc") ++ ++ act_led_activelow Set to "on" to invert the sense of the LED ++ (default "off") ++ N.B. For Pi3 see pi3-act-led overlay. ++ ++ act_led_gpio Set which GPIO to use for the activity LED ++ (in case you want to connect it to an external ++ device) ++ (default "16" on a non-Plus board, "47" on a ++ Plus or Pi 2) ++ N.B. For Pi3 see pi3-act-led overlay. ++ ++ pwr_led_trigger ++ pwr_led_activelow ++ pwr_led_gpio ++ As for act_led_*, but using the PWR LED. ++ Not available on Model A/B boards. ++ ++ N.B. It is recommended to only enable those interfaces that are needed. ++ Leaving all interfaces enabled can lead to unwanted behaviour (i2c_vc ++ interfering with Pi Camera, I2S and SPI hogging GPIO pins, etc.) ++ Note also that i2c, i2c_arm and i2c_vc are aliases for the physical ++ interfaces i2c0 and i2c1. Use of the numeric variants is still possible ++ but deprecated because the ARM/VC assignments differ between board ++ revisions. The same board-specific mapping applies to i2c_baudrate, ++ and the other i2c baudrate parameters. ++ ++ ++Name: adau1977-adc ++Info: Overlay for activation of ADAU1977 ADC codec over I2C for control ++ and I2S for data. ++Load: dtoverlay=adau1977-adc ++Params: ++ ++ ++Name: ads1015 ++Info: Overlay for activation of Texas Instruments ADS1015 ADC over I2C ++Load: dtoverlay=ads1015,= ++Params: addr I2C bus address of device. Set based on how the ++ addr pin is wired. (default=0x48 assumes addr ++ is pulled to GND) ++ cha_enable Enable virtual channel a. (default=true) ++ cha_cfg Set the configuration for virtual channel a. ++ (default=4 configures this channel for the ++ voltage at A0 with respect to GND) ++ cha_datarate Set the datarate (samples/sec) for this channel. ++ (default=4 sets 1600 sps) ++ cha_gain Set the gain of the Programmable Gain ++ Amplifier for this channel. (default=2 sets the ++ full scale of the channel to 2.048 Volts) ++ ++ Channel (ch) parameters can be set for each enabled channel. ++ A maximum of 4 channels can be enabled (letters a thru d). ++ For more information refer to the device datasheet at: ++ http://www.ti.com/lit/ds/symlink/ads1015.pdf ++ ++ ++Name: ads7846 ++Info: ADS7846 Touch controller ++Load: dtoverlay=ads7846,= ++Params: cs SPI bus Chip Select (default 1) ++ speed SPI bus speed (default 2MHz, max 3.25MHz) ++ penirq GPIO used for PENIRQ. REQUIRED ++ penirq_pull Set GPIO pull (default 0=none, 2=pullup) ++ swapxy Swap x and y axis ++ xmin Minimum value on the X axis (default 0) ++ ymin Minimum value on the Y axis (default 0) ++ xmax Maximum value on the X axis (default 4095) ++ ymax Maximum value on the Y axis (default 4095) ++ pmin Minimum reported pressure value (default 0) ++ pmax Maximum reported pressure value (default 65535) ++ xohms Touchpanel sensitivity (X-plate resistance) ++ (default 400) ++ ++ penirq is required and usually xohms (60-100) has to be set as well. ++ Apart from that, pmax (255) and swapxy are also common. ++ The rest of the calibration can be done with xinput-calibrator. ++ See: github.com/notro/fbtft/wiki/FBTFT-on-Raspian ++ Device Tree binding document: ++ www.kernel.org/doc/Documentation/devicetree/bindings/input/ads7846.txt ++ ++ ++Name: akkordion-iqdacplus ++Info: Configures the Digital Dreamtime Akkordion Music Player (based on the ++ OEM IQAudIO DAC+ or DAC Zero module). ++Load: dtoverlay=akkordion-iqdacplus,= ++Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec ++ Digital volume control. Enable with ++ dtoverlay=akkordion-iqdacplus,24db_digital_gain ++ (The default behaviour is that the Digital ++ volume control is limited to a maximum of ++ 0dB. ie. it can attenuate but not provide ++ gain. For most users, this will be desired ++ as it will prevent clipping. By appending ++ the 24db_digital_gain parameter, the Digital ++ volume control will allow up to 24dB of ++ gain. If this parameter is enabled, it is the ++ responsibility of the user to ensure that ++ the Digital volume control is set to a value ++ that does not result in clipping/distortion!) ++ ++ ++Name: allo-piano-dac-pcm512x-audio ++Info: Configures the Allo Piano DAC (2.0/2.1) audio cards. ++ (NB. This initial support is for 2.0 channel audio ONLY! ie. stereo. ++ The subwoofer outputs on the Piano 2.1 are not currently supported!) ++Load: dtoverlay=allo-piano-dac-pcm512x-audio, ++Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec ++ Digital volume control. ++ (The default behaviour is that the Digital ++ volume control is limited to a maximum of ++ 0dB. ie. it can attenuate but not provide ++ gain. For most users, this will be desired ++ as it will prevent clipping. By appending ++ the 24db_digital_gain parameter, the Digital ++ volume control will allow up to 24dB of ++ gain. If this parameter is enabled, it is the ++ responsibility of the user to ensure that ++ the Digital volume control is set to a value ++ that does not result in clipping/distortion!) ++ ++ ++Name: at86rf233 ++Info: Configures the Atmel AT86RF233 802.15.4 low-power WPAN transceiver, ++ connected to spi0.0 ++Load: dtoverlay=at86rf233,= ++Params: interrupt GPIO used for INT (default 23) ++ reset GPIO used for Reset (default 24) ++ sleep GPIO used for Sleep (default 25) ++ speed SPI bus speed in Hz (default 3000000) ++ trim Fine tuning of the internal capacitance ++ arrays (0=+0pF, 15=+4.5pF, default 15) ++ ++ ++Name: audioinjector-wm8731-audio ++Info: Configures the audioinjector.net audio add on soundcard ++Load: dtoverlay=audioinjector-wm8731-audio ++Params: ++ ++ ++Name: audremap ++Info: Switches PWM sound output to pins 12 (Right) & 13 (Left) ++Load: dtoverlay=audremap,= ++Params: swap_lr Reverse the channel allocation, which will also ++ swap the audio jack outputs (default off) ++ enable_jack Don't switch off the audio jack output ++ (default off) ++ ++ ++Name: bmp085_i2c-sensor ++Info: This overlay is now deprecated - see i2c-sensor ++Load: dtoverlay=bmp085_i2c-sensor ++Params: ++ ++ ++Name: dht11 ++Info: Overlay for the DHT11/DHT21/DHT22 humidity/temperature sensors ++ Also sometimes found with the part number(s) AM230x. ++Load: dtoverlay=dht11,= ++Params: gpiopin GPIO connected to the sensor's DATA output. ++ (default 4) ++ ++ ++Name: dionaudio-loco ++Info: Configures the Dion Audio LOCO DAC-AMP ++Load: dtoverlay=dionaudio-loco ++Params: ++ ++ ++Name: dpi18 ++Info: Overlay for a generic 18-bit DPI display ++ This uses GPIOs 0-21 (so no I2C, uart etc.), and activates the output ++ 2-3 seconds after the kernel has started. ++Load: dtoverlay=dpi18 ++Params: ++ ++ ++Name: dpi24 ++Info: Overlay for a generic 24-bit DPI display ++ This uses GPIOs 0-27 (so no I2C, uart etc.), and activates the output ++ 2-3 seconds after the kernel has started. ++Load: dtoverlay=dpi24 ++Params: ++ ++ ++Name: dwc-otg ++Info: Selects the dwc_otg USB controller driver which has fiq support. This ++ is the default on all except the Pi Zero which defaults to dwc2. ++Load: dtoverlay=dwc-otg ++Params: ++ ++ ++Name: dwc2 ++Info: Selects the dwc2 USB controller driver ++Load: dtoverlay=dwc2,= ++Params: dr_mode Dual role mode: "host", "peripheral" or "otg" ++ ++ g-rx-fifo-size Size of rx fifo size in gadget mode ++ ++ g-np-tx-fifo-size Size of non-periodic tx fifo size in gadget ++ mode ++ ++ g-tx-fifo-size Size of periodic tx fifo per endpoint ++ (except ep0) in gadget mode ++ ++ ++[ The ds1307-rtc overlay has been deleted. See i2c-rtc. ] ++ ++ ++Name: enc28j60 ++Info: Overlay for the Microchip ENC28J60 Ethernet Controller on SPI0 ++Load: dtoverlay=enc28j60,= ++Params: int_pin GPIO used for INT (default 25) ++ ++ speed SPI bus speed (default 12000000) ++ ++ ++Name: enc28j60-spi2 ++Info: Overlay for the Microchip ENC28J60 Ethernet Controller on SPI2 ++Load: dtoverlay=enc28j60-spi2,= ++Params: int_pin GPIO used for INT (default 39) ++ ++ speed SPI bus speed (default 12000000) ++ ++ ++Name: gpio-ir ++Info: Use GPIO pin as rc-core style infrared receiver input. The rc-core- ++ based gpio_ir_recv driver maps received keys directly to a ++ /dev/input/event* device, all decoding is done by the kernel - LIRC is ++ not required! The key mapping and other decoding parameters can be ++ configured by "ir-keytable" tool. ++Load: dtoverlay=gpio-ir,= ++Params: gpio_pin Input pin number. Default is 18. ++ ++ gpio_pull Desired pull-up/down state (off, down, up) ++ Default is "down". ++ ++ rc-map-name Default rc keymap (can also be changed by ++ ir-keytable), defaults to "rc-rc6-mce" ++ ++ ++Name: gpio-poweroff ++Info: Drives a GPIO high or low on poweroff (including halt) ++Load: dtoverlay=gpio-poweroff,= ++Params: gpiopin GPIO for signalling (default 26) ++ ++ active_low Set if the power control device requires a ++ high->low transition to trigger a power-down. ++ Note that this will require the support of a ++ custom dt-blob.bin to prevent a power-down ++ during the boot process, and that a reboot ++ will also cause the pin to go low. ++ ++ ++Name: hifiberry-amp ++Info: Configures the HifiBerry Amp and Amp+ audio cards ++Load: dtoverlay=hifiberry-amp ++Params: ++ ++ ++Name: hifiberry-dac ++Info: Configures the HifiBerry DAC audio card ++Load: dtoverlay=hifiberry-dac ++Params: ++ ++ ++Name: hifiberry-dacplus ++Info: Configures the HifiBerry DAC+ audio card ++Load: dtoverlay=hifiberry-dacplus,= ++Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec ++ Digital volume control. Enable with ++ "dtoverlay=hifiberry-dacplus,24db_digital_gain" ++ (The default behaviour is that the Digital ++ volume control is limited to a maximum of ++ 0dB. ie. it can attenuate but not provide ++ gain. For most users, this will be desired ++ as it will prevent clipping. By appending ++ the 24dB_digital_gain parameter, the Digital ++ volume control will allow up to 24dB of ++ gain. If this parameter is enabled, it is the ++ responsibility of the user to ensure that ++ the Digital volume control is set to a value ++ that does not result in clipping/distortion!) ++ slave Force DAC+ Pro into slave mode, using Pi as ++ master for bit clock and frame clock. ++ ++ ++Name: hifiberry-digi ++Info: Configures the HifiBerry Digi and Digi+ audio card ++Load: dtoverlay=hifiberry-digi ++Params: ++ ++ ++Name: hifiberry-digi-pro ++Info: Configures the HifiBerry Digi+ Pro audio card ++Load: dtoverlay=hifiberry-digi-pro ++Params: ++ ++ ++Name: hy28a ++Info: HY28A - 2.8" TFT LCD Display Module by HAOYU Electronics ++ Default values match Texy's display shield ++Load: dtoverlay=hy28a,= ++Params: speed Display SPI bus speed ++ ++ rotate Display rotation {0,90,180,270} ++ ++ fps Delay between frame updates ++ ++ debug Debug output level {0-7} ++ ++ xohms Touchpanel sensitivity (X-plate resistance) ++ ++ resetgpio GPIO used to reset controller ++ ++ ledgpio GPIO used to control backlight ++ ++ ++Name: hy28b ++Info: HY28B - 2.8" TFT LCD Display Module by HAOYU Electronics ++ Default values match Texy's display shield ++Load: dtoverlay=hy28b,= ++Params: speed Display SPI bus speed ++ ++ rotate Display rotation {0,90,180,270} ++ ++ fps Delay between frame updates ++ ++ debug Debug output level {0-7} ++ ++ xohms Touchpanel sensitivity (X-plate resistance) ++ ++ resetgpio GPIO used to reset controller ++ ++ ledgpio GPIO used to control backlight ++ ++ ++Name: i2c-bcm2708 ++Info: Fall back to the i2c_bcm2708 driver for the i2c_arm bus. ++Load: dtoverlay=i2c-bcm2708 ++Params: ++ ++ ++Name: i2c-gpio ++Info: Adds support for software i2c controller on gpio pins ++Load: dtoverlay=i2c-gpio,= ++Params: i2c_gpio_sda GPIO used for I2C data (default "23") ++ ++ i2c_gpio_scl GPIO used for I2C clock (default "24") ++ ++ i2c_gpio_delay_us Clock delay in microseconds ++ (default "2" = ~100kHz) ++ ++ ++Name: i2c-mux ++Info: Adds support for a number of I2C bus multiplexers on i2c_arm ++Load: dtoverlay=i2c-mux,= ++Params: pca9542 Select the NXP PCA9542 device ++ ++ pca9545 Select the NXP PCA9545 device ++ ++ pca9548 Select the NXP PCA9548 device ++ ++ addr Change I2C address of the device (default 0x70) ++ ++ ++[ The i2c-mux-pca9548a overlay has been deleted. See i2c-mux. ] ++ ++ ++Name: i2c-pwm-pca9685a ++Info: Adds support for an NXP PCA9685A I2C PWM controller on i2c_arm ++Load: dtoverlay=i2c-pwm-pca9685a,= ++Params: addr I2C address of PCA9685A (default 0x40) ++ ++ ++Name: i2c-rtc ++Info: Adds support for a number of I2C Real Time Clock devices ++Load: dtoverlay=i2c-rtc,= ++Params: abx80x Select one of the ABx80x family: ++ AB0801, AB0803, AB0804, AB0805, ++ AB1801, AB1803, AB1804, AB1805 ++ ++ ds1307 Select the DS1307 device ++ ++ ds1339 Select the DS1339 device ++ ++ ds3231 Select the DS3231 device ++ ++ mcp7940x Select the MCP7940x device ++ ++ mcp7941x Select the MCP7941x device ++ ++ pcf2127 Select the PCF2127 device ++ ++ pcf8523 Select the PCF8523 device ++ ++ pcf8563 Select the PCF8563 device ++ ++ trickle-diode-type Diode type for trickle charge - "standard" or ++ "schottky" (ABx80x only) ++ ++ trickle-resistor-ohms Resistor value for trickle charge (DS1339, ++ ABx80x) ++ ++ wakeup-source Specify that the RTC can be used as a wakeup ++ source ++ ++ ++Name: i2c-sensor ++Info: Adds support for a number of I2C barometric pressure and temperature ++ sensors on i2c_arm ++Load: dtoverlay=i2c-sensor,= ++Params: bmp085 Select the Bosch sensortronic BMP085 ++ ++ bmp280 Select the Bosch sensortronic BMP280 ++ ++ ++Name: i2c0-bcm2708 ++Info: Enable the i2c_bcm2708 driver for the i2c0 bus. Not all pin combinations ++ are usable on all platforms. ++Load: dtoverlay=i2c0-bcm2708,= ++Params: sda0_pin GPIO pin for SDA0 (deprecated - use pins_*) ++ scl0_pin GPIO pin for SCL0 (deprecated - use pins_*) ++ pins_0_1 Use pins 0 and 1 (default) ++ pins_28_29 Use pins 28 and 29 ++ pins_44_45 Use pins 44 and 45 ++ pins_46_47 Use pins 46 and 47 ++ ++ ++Name: i2c1-bcm2708 ++Info: Enable the i2c_bcm2708 driver for the i2c1 bus ++Load: dtoverlay=i2c1-bcm2708,= ++Params: sda1_pin GPIO pin for SDA1 (2 or 44 - default 2) ++ scl1_pin GPIO pin for SCL1 (3 or 45 - default 3) ++ pin_func Alternative pin function (4 (alt0), 6 (alt2) - ++ default 4) ++ ++ ++Name: i2s-gpio28-31 ++Info: move I2S function block to GPIO 28 to 31 ++Load: dtoverlay=i2s-gpio28-31 ++Params: ++ ++ ++Name: iqaudio-dac ++Info: Configures the IQaudio DAC audio card ++Load: dtoverlay=iqaudio-dac, ++Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec ++ Digital volume control. Enable with ++ "dtoverlay=iqaudio-dac,24db_digital_gain" ++ (The default behaviour is that the Digital ++ volume control is limited to a maximum of ++ 0dB. ie. it can attenuate but not provide ++ gain. For most users, this will be desired ++ as it will prevent clipping. By appending ++ the 24db_digital_gain parameter, the Digital ++ volume control will allow up to 24dB of ++ gain. If this parameter is enabled, it is the ++ responsibility of the user to ensure that ++ the Digital volume control is set to a value ++ that does not result in clipping/distortion!) ++ ++ ++Name: iqaudio-dacplus ++Info: Configures the IQaudio DAC+ audio card ++Load: dtoverlay=iqaudio-dacplus,= ++Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec ++ Digital volume control. Enable with ++ "dtoverlay=iqaudio-dacplus,24db_digital_gain" ++ (The default behaviour is that the Digital ++ volume control is limited to a maximum of ++ 0dB. ie. it can attenuate but not provide ++ gain. For most users, this will be desired ++ as it will prevent clipping. By appending ++ the 24db_digital_gain parameter, the Digital ++ volume control will allow up to 24dB of ++ gain. If this parameter is enabled, it is the ++ responsibility of the user to ensure that ++ the Digital volume control is set to a value ++ that does not result in clipping/distortion!) ++ auto_mute_amp If specified, unmute/mute the IQaudIO amp when ++ starting/stopping audio playback. ++ unmute_amp If specified, unmute the IQaudIO amp once when ++ the DAC driver module loads. ++ ++ ++Name: iqaudio-digi-wm8804-audio ++Info: Configures the IQAudIO Digi WM8804 audio card ++Load: dtoverlay=iqaudio-digi-wm8804-audio,= ++Params: card_name Override the default, "IQAudIODigi", card name. ++ dai_name Override the default, "IQAudIO Digi", dai name. ++ dai_stream_name Override the default, "IQAudIO Digi HiFi", ++ dai stream name. ++ ++ ++Name: justboom-dac ++Info: Configures the JustBoom DAC HAT, Amp HAT, DAC Zero and Amp Zero audio ++ cards ++Load: dtoverlay=justboom-dac,= ++Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec ++ Digital volume control. Enable with ++ "dtoverlay=justboom-dac,24db_digital_gain" ++ (The default behaviour is that the Digital ++ volume control is limited to a maximum of ++ 0dB. ie. it can attenuate but not provide ++ gain. For most users, this will be desired ++ as it will prevent clipping. By appending ++ the 24dB_digital_gain parameter, the Digital ++ volume control will allow up to 24dB of ++ gain. If this parameter is enabled, it is the ++ responsibility of the user to ensure that ++ the Digital volume control is set to a value ++ that does not result in clipping/distortion!) ++ ++ ++Name: justboom-digi ++Info: Configures the JustBoom Digi HAT and Digi Zero audio cards ++Load: dtoverlay=justboom-digi ++Params: ++ ++ ++Name: lirc-rpi ++Info: Configures lirc-rpi (Linux Infrared Remote Control for Raspberry Pi) ++ Consult the module documentation for more details. ++Load: dtoverlay=lirc-rpi,= ++Params: gpio_out_pin GPIO for output (default "17") ++ ++ gpio_in_pin GPIO for input (default "18") ++ ++ gpio_in_pull Pull up/down/off on the input pin ++ (default "down") ++ ++ sense Override the IR receive auto-detection logic: ++ "0" = force active-high ++ "1" = force active-low ++ "-1" = use auto-detection ++ (default "-1") ++ ++ softcarrier Turn the software carrier "on" or "off" ++ (default "on") ++ ++ invert "on" = invert the output pin (default "off") ++ ++ debug "on" = enable additional debug messages ++ (default "off") ++ ++ ++Name: mcp23017 ++Info: Configures the MCP23017 I2C GPIO expander ++Load: dtoverlay=mcp23017,= ++Params: gpiopin Gpio pin connected to the INTA output of the ++ MCP23017 (default: 4) ++ ++ addr I2C address of the MCP23017 (default: 0x20) ++ ++ ++Name: mcp23s17 ++Info: Configures the MCP23S08/17 SPI GPIO expanders. ++ If devices are present on SPI1 or SPI2, those interfaces must be enabled ++ with one of the spi1-1/2/3cs and/or spi2-1/2/3cs overlays. ++ If interrupts are enabled for a device on a given CS# on a SPI bus, that ++ device must be the only one present on that SPI bus/CS#. ++Load: dtoverlay=mcp23s17,= ++Params: s08-spi--present 4-bit integer, bitmap indicating MCP23S08 ++ devices present on SPI, CS# ++ ++ s17-spi--present 8-bit integer, bitmap indicating MCP23S17 ++ devices present on SPI, CS# ++ ++ s08-spi--int-gpio integer, enables interrupts on a single ++ MCP23S08 device on SPI, CS#, specifies ++ the GPIO pin to which INT output of MCP23S08 ++ is connected. ++ ++ s17-spi--int-gpio integer, enables mirrored interrupts on a ++ single MCP23S17 device on SPI, CS#, ++ specifies the GPIO pin to which either INTA ++ or INTB output of MCP23S17 is connected. ++ ++ ++Name: mcp2515-can0 ++Info: Configures the MCP2515 CAN controller on spi0.0 ++Load: dtoverlay=mcp2515-can0,= ++Params: oscillator Clock frequency for the CAN controller (Hz) ++ ++ spimaxfrequency Maximum SPI frequence (Hz) ++ ++ interrupt GPIO for interrupt signal ++ ++ ++Name: mcp2515-can1 ++Info: Configures the MCP2515 CAN controller on spi0.1 ++Load: dtoverlay=mcp2515-can1,= ++Params: oscillator Clock frequency for the CAN controller (Hz) ++ ++ spimaxfrequency Maximum SPI frequence (Hz) ++ ++ interrupt GPIO for interrupt signal ++ ++ ++Name: midi-uart0 ++Info: Configures UART0 (ttyAMA0) so that a requested 38.4kbaud actually gets ++ 31.25kbaud, the frequency required for MIDI ++Load: dtoverlay=midi-uart0 ++Params: ++ ++ ++Name: mmc ++Info: Selects the bcm2835-mmc SD/MMC driver, optionally with overclock ++Load: dtoverlay=mmc,= ++Params: overclock_50 Clock (in MHz) to use when the MMC framework ++ requests 50MHz ++ ++ ++Name: mz61581 ++Info: MZ61581 display by Tontec ++Load: dtoverlay=mz61581,= ++Params: speed Display SPI bus speed ++ ++ rotate Display rotation {0,90,180,270} ++ ++ fps Delay between frame updates ++ ++ txbuflen Transmit buffer length (default 32768) ++ ++ debug Debug output level {0-7} ++ ++ xohms Touchpanel sensitivity (X-plate resistance) ++ ++ ++[ The pcf2127-rtc overlay has been deleted. See i2c-rtc. ] ++ ++ ++[ The pcf8523-rtc overlay has been deleted. See i2c-rtc. ] ++ ++ ++[ The pcf8563-rtc overlay has been deleted. See i2c-rtc. ] ++ ++ ++Name: pi3-act-led ++Info: Pi3 uses a GPIO expander to drive the LEDs which can only be accessed ++ from the VPU. There is a special driver for this with a separate DT ++ node, which has the unfortunate consequence of breaking the ++ act_led_gpio and act_led_activelow dtparams. ++ This overlay changes the GPIO controller back to the standard one and ++ restores the dtparams. ++Load: dtoverlay=pi3-act-led,= ++Params: activelow Set to "on" to invert the sense of the LED ++ (default "off") ++ ++ gpio Set which GPIO to use for the activity LED ++ (in case you want to connect it to an external ++ device) ++ REQUIRED ++ ++ ++Name: pi3-disable-bt ++Info: Disable Pi3 Bluetooth and restore UART0/ttyAMA0 over GPIOs 14 & 15 ++ N.B. To disable the systemd service that initialises the modem so it ++ doesn't use the UART, use 'sudo systemctl disable hciuart'. ++Load: dtoverlay=pi3-disable-bt ++Params: ++ ++ ++Name: pi3-miniuart-bt ++Info: Switch Pi3 Bluetooth function to use the mini-UART (ttyS0) and restore ++ UART0/ttyAMA0 over GPIOs 14 & 15. Note that this may reduce the maximum ++ usable baudrate. ++ N.B. It is also necessary to edit /lib/systemd/system/hciuart.service ++ and replace ttyAMA0 with ttyS0, unless you have a system with udev rules ++ that create /dev/serial0 and /dev/serial1, in which case use ++ /dev/serial1 instead because it will always be correct. Furthermore, ++ you must also set core_freq=250 in config.txt or the miniuart will not ++ work. ++Load: dtoverlay=pi3-miniuart-bt ++Params: ++ ++ ++Name: piscreen ++Info: PiScreen display by OzzMaker.com ++Load: dtoverlay=piscreen,= ++Params: speed Display SPI bus speed ++ ++ rotate Display rotation {0,90,180,270} ++ ++ fps Delay between frame updates ++ ++ debug Debug output level {0-7} ++ ++ xohms Touchpanel sensitivity (X-plate resistance) ++ ++ ++Name: piscreen2r ++Info: PiScreen 2 with resistive TP display by OzzMaker.com ++Load: dtoverlay=piscreen2r,= ++Params: speed Display SPI bus speed ++ ++ rotate Display rotation {0,90,180,270} ++ ++ fps Delay between frame updates ++ ++ debug Debug output level {0-7} ++ ++ xohms Touchpanel sensitivity (X-plate resistance) ++ ++ ++Name: pisound ++Info: Configures the Blokas Labs pisound card ++Load: dtoverlay=pisound ++Params: ++ ++ ++Name: pitft22 ++Info: Adafruit PiTFT 2.2" screen ++Load: dtoverlay=pitft22,= ++Params: speed Display SPI bus speed ++ ++ rotate Display rotation {0,90,180,270} ++ ++ fps Delay between frame updates ++ ++ debug Debug output level {0-7} ++ ++ ++Name: pitft28-capacitive ++Info: Adafruit PiTFT 2.8" capacitive touch screen ++Load: dtoverlay=pitft28-capacitive,= ++Params: speed Display SPI bus speed ++ ++ rotate Display rotation {0,90,180,270} ++ ++ fps Delay between frame updates ++ ++ debug Debug output level {0-7} ++ ++ touch-sizex Touchscreen size x (default 240) ++ ++ touch-sizey Touchscreen size y (default 320) ++ ++ touch-invx Touchscreen inverted x axis ++ ++ touch-invy Touchscreen inverted y axis ++ ++ touch-swapxy Touchscreen swapped x y axis ++ ++ ++Name: pitft28-resistive ++Info: Adafruit PiTFT 2.8" resistive touch screen ++Load: dtoverlay=pitft28-resistive,= ++Params: speed Display SPI bus speed ++ ++ rotate Display rotation {0,90,180,270} ++ ++ fps Delay between frame updates ++ ++ debug Debug output level {0-7} ++ ++ ++Name: pitft35-resistive ++Info: Adafruit PiTFT 3.5" resistive touch screen ++Load: dtoverlay=pitft35-resistive,= ++Params: speed Display SPI bus speed ++ ++ rotate Display rotation {0,90,180,270} ++ ++ fps Delay between frame updates ++ ++ debug Debug output level {0-7} ++ ++ ++Name: pps-gpio ++Info: Configures the pps-gpio (pulse-per-second time signal via GPIO). ++Load: dtoverlay=pps-gpio,= ++Params: gpiopin Input GPIO (default "18") ++ assert_falling_edge When present, assert is indicated by a falling ++ edge, rather than by a rising edge ++ ++ ++Name: pwm ++Info: Configures a single PWM channel ++ Legal pin,function combinations for each channel: ++ PWM0: 12,4(Alt0) 18,2(Alt5) 40,4(Alt0) 52,5(Alt1) ++ PWM1: 13,4(Alt0) 19,2(Alt5) 41,4(Alt0) 45,4(Alt0) 53,5(Alt1) ++ N.B.: ++ 1) Pin 18 is the only one available on all platforms, and ++ it is the one used by the I2S audio interface. ++ Pins 12 and 13 might be better choices on an A+, B+ or Pi2. ++ 2) The onboard analogue audio output uses both PWM channels. ++ 3) So be careful mixing audio and PWM. ++ 4) Currently the clock must have been enabled and configured ++ by other means. ++Load: dtoverlay=pwm,= ++Params: pin Output pin (default 18) - see table ++ func Pin function (default 2 = Alt5) - see above ++ clock PWM clock frequency (informational) ++ ++ ++Name: pwm-2chan ++Info: Configures both PWM channels ++ Legal pin,function combinations for each channel: ++ PWM0: 12,4(Alt0) 18,2(Alt5) 40,4(Alt0) 52,5(Alt1) ++ PWM1: 13,4(Alt0) 19,2(Alt5) 41,4(Alt0) 45,4(Alt0) 53,5(Alt1) ++ N.B.: ++ 1) Pin 18 is the only one available on all platforms, and ++ it is the one used by the I2S audio interface. ++ Pins 12 and 13 might be better choices on an A+, B+ or Pi2. ++ 2) The onboard analogue audio output uses both PWM channels. ++ 3) So be careful mixing audio and PWM. ++ 4) Currently the clock must have been enabled and configured ++ by other means. ++Load: dtoverlay=pwm-2chan,= ++Params: pin Output pin (default 18) - see table ++ pin2 Output pin for other channel (default 19) ++ func Pin function (default 2 = Alt5) - see above ++ func2 Function for pin2 (default 2 = Alt5) ++ clock PWM clock frequency (informational) ++ ++ ++Name: qca7000 ++Info: I2SE's Evaluation Board for PLC Stamp micro ++Load: dtoverlay=qca7000,= ++Params: int_pin GPIO pin for interrupt signal (default 23) ++ ++ speed SPI bus speed (default 12 MHz) ++ ++ ++Name: raspidac3 ++Info: Configures the RaspiDAV Rev.3x audio card ++Load: dtoverlay=raspidac3 ++Params: ++ ++ ++Name: rpi-backlight ++Info: Raspberry Pi official display backlight driver ++Load: dtoverlay=rpi-backlight ++Params: ++ ++ ++Name: rpi-dac ++Info: Configures the RPi DAC audio card ++Load: dtoverlay=rpi-dac ++Params: ++ ++ ++Name: rpi-display ++Info: RPi-Display - 2.8" Touch Display by Watterott ++Load: dtoverlay=rpi-display,= ++Params: speed Display SPI bus speed ++ rotate Display rotation {0,90,180,270} ++ fps Delay between frame updates ++ debug Debug output level {0-7} ++ xohms Touchpanel sensitivity (X-plate resistance) ++ swapxy Swap x and y axis ++ ++ ++Name: rpi-ft5406 ++Info: Official Raspberry Pi display touchscreen ++Load: dtoverlay=rpi-ft5406 ++Params: ++ ++ ++Name: rpi-proto ++Info: Configures the RPi Proto audio card ++Load: dtoverlay=rpi-proto ++Params: ++ ++ ++Name: rpi-sense ++Info: Raspberry Pi Sense HAT ++Load: dtoverlay=rpi-sense ++Params: ++ ++ ++Name: rra-digidac1-wm8741-audio ++Info: Configures the Red Rocks Audio DigiDAC1 soundcard ++Load: dtoverlay=rra-digidac1-wm8741-audio ++Params: ++ ++ ++Name: sc16is750-i2c ++Info: Overlay for the NXP SC16IS750 UART with I2C Interface ++ Enables the chip on I2C1 at 0x48. To select another address, ++ please refer to table 10 in reference manual. ++ ++Load: dtoverlay=sc16is750-i2c,= ++Params: int_pin GPIO used for IRQ (default 24) ++ addr Address (default 0x48) ++ ++ ++Name: sc16is752-spi1 ++Info: Overlay for the NXP SC16IS752 Dual UART with SPI Interface ++ Enables the chip on SPI1. ++ N.B.: spi1 is only accessible on devices with a 40pin header, eg: ++ A+, B+, Zero and PI2 B; as well as the Compute Module. ++ ++Load: dtoverlay=sc16is752-spi1,= ++Params: int_pin GPIO used for IRQ (default 24) ++ ++ ++Name: sdhost ++Info: Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock. ++ N.B. This overlay is designed for situations where the mmc driver is ++ the default, so it disables the other (mmc) interface - this will kill ++ WiFi on a Pi3. If this isn't what you want, either use the sdtweak ++ overlay or the new sd_* dtparams of the base DTBs. ++Load: dtoverlay=sdhost,= ++Params: overclock_50 Clock (in MHz) to use when the MMC framework ++ requests 50MHz ++ ++ force_pio Disable DMA support (default off) ++ ++ pio_limit Number of blocks above which to use DMA ++ (default 1) ++ ++ debug Enable debug output (default off) ++ ++ ++Name: sdio ++Info: Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock, ++ and enables SDIO via GPIOs 22-27. ++Load: dtoverlay=sdio,= ++Params: overclock_50 SD Clock (in MHz) to use when the MMC framework ++ requests 50MHz ++ ++ sdio_overclock SDIO Clock (in MHz) to use when the MMC ++ framework requests 50MHz ++ ++ force_pio Disable DMA support (default off) ++ ++ pio_limit Number of blocks above which to use DMA ++ (default 1) ++ ++ debug Enable debug output (default off) ++ ++ poll_once Disable SDIO-device polling every second ++ (default on: polling once at boot-time) ++ ++ bus_width Set the SDIO host bus width (default 4 bits) ++ ++ ++Name: sdio-1bit ++Info: Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock, ++ and enables 1-bit SDIO via GPIOs 22-25. ++Load: dtoverlay=sdio-1bit,= ++Params: overclock_50 SD Clock (in MHz) to use when the MMC framework ++ requests 50MHz ++ ++ sdio_overclock SDIO Clock (in MHz) to use when the MMC ++ framework requests 50MHz ++ ++ force_pio Disable DMA support (default off) ++ ++ pio_limit Number of blocks above which to use DMA ++ (default 1) ++ ++ debug Enable debug output (default off) ++ ++ poll_once Disable SDIO-device polling every second ++ (default on: polling once at boot-time) ++ ++ ++Name: sdtweak ++Info: Tunes the bcm2835-sdhost SD/MMC driver ++ N.B. This functionality is now available via the sd_* dtparams in the ++ base DTB. ++Load: dtoverlay=sdtweak,= ++Params: overclock_50 Clock (in MHz) to use when the MMC framework ++ requests 50MHz ++ ++ force_pio Disable DMA support (default off) ++ ++ pio_limit Number of blocks above which to use DMA ++ (default 1) ++ ++ debug Enable debug output (default off) ++ ++ ++Name: smi ++Info: Enables the Secondary Memory Interface peripheral. Uses GPIOs 2-25! ++Load: dtoverlay=smi ++Params: ++ ++ ++Name: smi-dev ++Info: Enables the userspace interface for the SMI driver ++Load: dtoverlay=smi-dev ++Params: ++ ++ ++Name: smi-nand ++Info: Enables access to NAND flash via the SMI interface ++Load: dtoverlay=smi-nand ++Params: ++ ++ ++Name: spi-gpio35-39 ++Info: move SPI function block to GPIO 35 to 39 ++Load: dtoverlay=spi-gpio35-39 ++Params: ++ ++ ++Name: spi-rtc ++Info: Adds support for a number of SPI Real Time Clock devices ++Load: dtoverlay=spi-rtc,= ++Params: pcf2123 Select the PCF2123 device ++ ++ ++Name: spi0-hw-cs ++Info: Re-enables hardware CS/CE (chip selects) for SPI0 ++Load: dtoverlay=spi0-hw-cs ++Params: ++ ++ ++Name: spi1-1cs ++Info: Enables spi1 with a single chip select (CS) line and associated spidev ++ dev node. The gpio pin number for the CS line and spidev device node ++ creation are configurable. ++ N.B.: spi1 is only accessible on devices with a 40pin header, eg: ++ A+, B+, Zero and PI2 B; as well as the Compute Module. ++Load: dtoverlay=spi1-1cs,= ++Params: cs0_pin GPIO pin for CS0 (default 18 - BCM SPI1_CE0). ++ cs0_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev1.0 (default ++ is 'okay' or enabled). ++ ++ ++Name: spi1-2cs ++Info: Enables spi1 with two chip select (CS) lines and associated spidev ++ dev nodes. The gpio pin numbers for the CS lines and spidev device node ++ creation are configurable. ++ N.B.: spi1 is only accessible on devices with a 40pin header, eg: ++ A+, B+, Zero and PI2 B; as well as the Compute Module. ++Load: dtoverlay=spi1-2cs,= ++Params: cs0_pin GPIO pin for CS0 (default 18 - BCM SPI1_CE0). ++ cs1_pin GPIO pin for CS1 (default 17 - BCM SPI1_CE1). ++ cs0_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev1.0 (default ++ is 'okay' or enabled). ++ cs1_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev1.1 (default ++ is 'okay' or enabled). ++ ++ ++Name: spi1-3cs ++Info: Enables spi1 with three chip select (CS) lines and associated spidev ++ dev nodes. The gpio pin numbers for the CS lines and spidev device node ++ creation are configurable. ++ N.B.: spi1 is only accessible on devices with a 40pin header, eg: ++ A+, B+, Zero and PI2 B; as well as the Compute Module. ++Load: dtoverlay=spi1-3cs,= ++Params: cs0_pin GPIO pin for CS0 (default 18 - BCM SPI1_CE0). ++ cs1_pin GPIO pin for CS1 (default 17 - BCM SPI1_CE1). ++ cs2_pin GPIO pin for CS2 (default 16 - BCM SPI1_CE2). ++ cs0_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev1.0 (default ++ is 'okay' or enabled). ++ cs1_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev1.1 (default ++ is 'okay' or enabled). ++ cs2_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev1.2 (default ++ is 'okay' or enabled). ++ ++ ++Name: spi2-1cs ++Info: Enables spi2 with a single chip select (CS) line and associated spidev ++ dev node. The gpio pin number for the CS line and spidev device node ++ creation are configurable. ++ N.B.: spi2 is only accessible with the Compute Module. ++Load: dtoverlay=spi2-1cs,= ++Params: cs0_pin GPIO pin for CS0 (default 43 - BCM SPI2_CE0). ++ cs0_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev2.0 (default ++ is 'okay' or enabled). ++ ++ ++Name: spi2-2cs ++Info: Enables spi2 with two chip select (CS) lines and associated spidev ++ dev nodes. The gpio pin numbers for the CS lines and spidev device node ++ creation are configurable. ++ N.B.: spi2 is only accessible with the Compute Module. ++Load: dtoverlay=spi2-2cs,= ++Params: cs0_pin GPIO pin for CS0 (default 43 - BCM SPI2_CE0). ++ cs1_pin GPIO pin for CS1 (default 44 - BCM SPI2_CE1). ++ cs0_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev2.0 (default ++ is 'okay' or enabled). ++ cs1_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev2.1 (default ++ is 'okay' or enabled). ++ ++ ++Name: spi2-3cs ++Info: Enables spi2 with three chip select (CS) lines and associated spidev ++ dev nodes. The gpio pin numbers for the CS lines and spidev device node ++ creation are configurable. ++ N.B.: spi2 is only accessible with the Compute Module. ++Load: dtoverlay=spi2-3cs,= ++Params: cs0_pin GPIO pin for CS0 (default 43 - BCM SPI2_CE0). ++ cs1_pin GPIO pin for CS1 (default 44 - BCM SPI2_CE1). ++ cs2_pin GPIO pin for CS2 (default 45 - BCM SPI2_CE2). ++ cs0_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev2.0 (default ++ is 'okay' or enabled). ++ cs1_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev2.1 (default ++ is 'okay' or enabled). ++ cs2_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev2.2 (default ++ is 'okay' or enabled). ++ ++ ++Name: tinylcd35 ++Info: 3.5" Color TFT Display by www.tinylcd.com ++ Options: Touch, RTC, keypad ++Load: dtoverlay=tinylcd35,= ++Params: speed Display SPI bus speed ++ ++ rotate Display rotation {0,90,180,270} ++ ++ fps Delay between frame updates ++ ++ debug Debug output level {0-7} ++ ++ touch Enable touch panel ++ ++ touchgpio Touch controller IRQ GPIO ++ ++ xohms Touchpanel: Resistance of X-plate in ohms ++ ++ rtc-pcf PCF8563 Real Time Clock ++ ++ rtc-ds DS1307 Real Time Clock ++ ++ keypad Enable keypad ++ ++ Examples: ++ Display with touchpanel, PCF8563 RTC and keypad: ++ dtoverlay=tinylcd35,touch,rtc-pcf,keypad ++ Old touch display: ++ dtoverlay=tinylcd35,touch,touchgpio=3 ++ ++ ++Name: uart1 ++Info: Enable uart1 in place of uart0 ++Load: dtoverlay=uart1,= ++Params: txd1_pin GPIO pin for TXD1 (14, 32 or 40 - default 14) ++ ++ rxd1_pin GPIO pin for RXD1 (15, 33 or 41 - default 15) ++ ++ ++Name: vc4-fkms-v3d ++Info: Enable Eric Anholt's DRM VC4 V3D driver on top of the dispmanx ++ display stack. ++Load: dtoverlay=vc4-fkms-v3d, ++Params: cma-256 CMA is 256MB, 256MB-aligned (needs 1GB) ++ cma-192 CMA is 192MB, 256MB-aligned (needs 1GB) ++ cma-128 CMA is 128MB, 128MB-aligned ++ cma-96 CMA is 96MB, 128MB-aligned ++ cma-64 CMA is 64MB, 64MB-aligned ++ ++ ++Name: vc4-kms-v3d ++Info: Enable Eric Anholt's DRM VC4 HDMI/HVS/V3D driver. Running startx or ++ booting to GUI while this overlay is in use will cause interesting ++ lockups. ++Load: dtoverlay=vc4-kms-v3d, ++Params: cma-256 CMA is 256MB, 256MB-aligned (needs 1GB) ++ cma-192 CMA is 192MB, 256MB-aligned (needs 1GB) ++ cma-128 CMA is 128MB, 128MB-aligned ++ cma-96 CMA is 96MB, 128MB-aligned ++ cma-64 CMA is 64MB, 64MB-aligned ++ ++ ++Name: vga666 ++Info: Overlay for the Fen Logic VGA666 board ++ This uses GPIOs 2-21 (so no I2C), and activates the output 2-3 seconds ++ after the kernel has started. ++Load: dtoverlay=vga666 ++Params: ++ ++ ++Name: w1-gpio ++Info: Configures the w1-gpio Onewire interface module. ++ Use this overlay if you *don't* need a GPIO to drive an external pullup. ++Load: dtoverlay=w1-gpio,= ++Params: gpiopin GPIO for I/O (default "4") ++ ++ pullup Non-zero, "on", or "y" to enable the parasitic ++ power (2-wire, power-on-data) feature ++ ++ ++Name: w1-gpio-pullup ++Info: Configures the w1-gpio Onewire interface module. ++ Use this overlay if you *do* need a GPIO to drive an external pullup. ++Load: dtoverlay=w1-gpio-pullup,= ++Params: gpiopin GPIO for I/O (default "4") ++ ++ pullup Non-zero, "on", or "y" to enable the parasitic ++ power (2-wire, power-on-data) feature ++ ++ extpullup GPIO for external pullup (default "5") ++ ++ ++Name: wittypi ++Info: Configures the wittypi RTC module. ++Load: dtoverlay=wittypi,= ++Params: led_gpio GPIO for LED (default "17") ++ led_trigger Choose which activity the LED tracks (default ++ "default-on") ++ ++ ++Troubleshooting ++=============== ++ ++If you are experiencing problems that you think are DT-related, enable DT ++diagnostic output by adding this to /boot/config.txt: ++ ++ dtdebug=on ++ ++and rebooting. Then run: ++ ++ sudo vcdbg log msg ++ ++and look for relevant messages. ++ ++Further reading ++=============== ++ ++This is only meant to be a quick introduction to the subject of Device Tree on ++Raspberry Pi. There is a more complete explanation here: ++ ++http://www.raspberrypi.org/documentation/configuration/device-tree.md +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/adau1977-adc-overlay.dts +@@ -0,0 +1,53 @@ ++// Definitions for ADAU1977 ADC ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&soc>; ++ ++ __overlay__ { ++ codec_supply: fixedregulator@0 { ++ compatible = "regulator-fixed"; ++ regulator-name = "AVDD"; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c>; ++ ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ adau1977: codec@11 { ++ compatible = "adi,adau1977"; ++ reg = <0x11>; ++ reset-gpios = <&gpio 5 0>; ++ AVDD-supply = <&codec_supply>; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "adi,adau1977-adc"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/ads1015-overlay.dts +@@ -0,0 +1,98 @@ ++/* ++ * 2016 - Erik Sejr ++ */ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ /* ----------- ADS1015 ------------ */ ++ fragment@0 { ++ target = <&i2c_arm>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ads1015: ads1015 { ++ compatible = "ti,ads1015"; ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <0x48>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "i2c_arm/ads1015"; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ channel_a: channel_a { ++ reg = <4>; ++ ti,gain = <2>; ++ ti,datarate = <4>; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target-path = "i2c_arm/ads1015"; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ channel_b: channel_b { ++ reg = <5>; ++ ti,gain = <2>; ++ ti,datarate = <4>; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target-path = "i2c_arm/ads1015"; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ channel_c: channel_c { ++ reg = <6>; ++ ti,gain = <2>; ++ ti,datarate = <4>; ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target-path = "i2c_arm/ads1015"; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ channel_d: channel_d { ++ reg = <7>; ++ ti,gain = <2>; ++ ti,datarate = <4>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ addr = <&ads1015>,"reg:0"; ++ cha_enable = <0>,"=1"; ++ cha_cfg = <&channel_a>,"reg:0"; ++ cha_gain = <&channel_a>,"ti,gain:0"; ++ cha_datarate = <&channel_a>,"ti,datarate:0"; ++ chb_enable = <0>,"=2"; ++ chb_cfg = <&channel_b>,"reg:0"; ++ chb_gain = <&channel_b>,"ti,gain:0"; ++ chb_datarate = <&channel_b>,"ti,datarate:0"; ++ chc_enable = <0>,"=3"; ++ chc_cfg = <&channel_c>,"reg:0"; ++ chc_gain = <&channel_c>,"ti,gain:0"; ++ chc_datarate = <&channel_c>,"ti,datarate:0"; ++ chd_enable = <0>,"=4"; ++ chd_cfg = <&channel_d>,"reg:0"; ++ chd_gain = <&channel_d>,"ti,gain:0"; ++ chd_datarate = <&channel_d>,"ti,datarate:0"; ++ }; ++ ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/ads7846-overlay.dts +@@ -0,0 +1,89 @@ ++/* ++ * Generic Device Tree overlay for the ADS7846 touch controller ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ ads7846_pins: ads7846_pins { ++ brcm,pins = <255>; /* illegal default value */ ++ brcm,function = <0>; /* in */ ++ brcm,pull = <0>; /* none */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ ads7846: ads7846@1 { ++ compatible = "ti,ads7846"; ++ reg = <1>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&ads7846_pins>; ++ ++ spi-max-frequency = <2000000>; ++ interrupts = <255 2>; /* high-to-low edge triggered */ ++ interrupt-parent = <&gpio>; ++ pendown-gpio = <&gpio 255 0>; ++ ++ /* driver defaults */ ++ ti,x-min = /bits/ 16 <0>; ++ ti,y-min = /bits/ 16 <0>; ++ ti,x-max = /bits/ 16 <0x0FFF>; ++ ti,y-max = /bits/ 16 <0x0FFF>; ++ ti,pressure-min = /bits/ 16 <0>; ++ ti,pressure-max = /bits/ 16 <0xFFFF>; ++ ti,x-plate-ohms = /bits/ 16 <400>; ++ }; ++ }; ++ }; ++ __overrides__ { ++ cs = <&ads7846>,"reg:0"; ++ speed = <&ads7846>,"spi-max-frequency:0"; ++ penirq = <&ads7846_pins>,"brcm,pins:0", /* REQUIRED */ ++ <&ads7846>,"interrupts:0", ++ <&ads7846>,"pendown-gpio:4"; ++ penirq_pull = <&ads7846_pins>,"brcm,pull:0"; ++ swapxy = <&ads7846>,"ti,swap-xy?"; ++ xmin = <&ads7846>,"ti,x-min;0"; ++ ymin = <&ads7846>,"ti,y-min;0"; ++ xmax = <&ads7846>,"ti,x-max;0"; ++ ymax = <&ads7846>,"ti,y-max;0"; ++ pmin = <&ads7846>,"ti,pressure-min;0"; ++ pmax = <&ads7846>,"ti,pressure-max;0"; ++ xohms = <&ads7846>,"ti,x-plate-ohms;0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/akkordion-iqdacplus-overlay.dts +@@ -0,0 +1,46 @@ ++// Definitions for Digital Dreamtime Akkordion using IQaudIO DAC+ or DACZero ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcm5122@4c { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5122"; ++ reg = <0x4c>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ frag2: __overlay__ { ++ compatible = "iqaudio,iqaudio-dac"; ++ card_name = "Akkordion"; ++ dai_name = "IQaudIO DAC"; ++ dai_stream_name = "IQaudIO DAC HiFi"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ 24db_digital_gain = <&frag2>,"iqaudio,24db_digital_gain?"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/allo-piano-dac-pcm512x-audio-overlay.dts +@@ -0,0 +1,54 @@ ++/* ++ * Definitions for Allo Piano DAC (2.0/2.1) boards ++ * ++ * NB. The Piano DAC 2.1 board contains 2x TI PCM5142 DAC's. One DAC is stereo ++ * (left/right) and the other provides a subwoofer output, using DSP on the ++ * chip for digital high/low pass crossover. ++ * The initial support for this hardware, that doesn't require any codec driver ++ * modifications, uses only one DAC chip for stereo (left/right) output, the ++ * chip with 0x4c slave address. The other chip at 0x4d is currently ignored! ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcm5142@4c { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5142"; ++ reg = <0x4c>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ piano_dac: __overlay__ { ++ compatible = "allo,piano-dac"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ 24db_digital_gain = ++ <&piano_dac>,"allo,24db_digital_gain?"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/at86rf233-overlay.dts +@@ -0,0 +1,57 @@ ++/dts-v1/; ++/plugin/; ++ ++/* Overlay for Atmel AT86RF233 IEEE 802.15.4 WPAN transceiver on spi0.0 */ ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "okay"; ++ ++ lowpan0: at86rf233@0 { ++ compatible = "atmel,at86rf233"; ++ reg = <0>; ++ interrupt-parent = <&gpio>; ++ interrupts = <23 4>; /* active high */ ++ reset-gpio = <&gpio 24 1>; ++ sleep-gpio = <&gpio 25 1>; ++ spi-max-frequency = <3000000>; ++ xtal-trim = /bits/ 8 <0xf>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&gpio>; ++ __overlay__ { ++ lowpan0_pins: lowpan0_pins { ++ brcm,pins = <23 24 25>; ++ brcm,function = <0 1 1>; /* in out out */ ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ interrupt = <&lowpan0>, "interrupts:0", ++ <&lowpan0_pins>, "brcm,pins:0"; ++ reset = <&lowpan0>, "reset-gpio:4", ++ <&lowpan0_pins>, "brcm,pins:4"; ++ sleep = <&lowpan0>, "sleep-gpio:4", ++ <&lowpan0_pins>, "brcm,pins:8"; ++ speed = <&lowpan0>, "spi-max-frequency:0"; ++ trim = <&lowpan0>, "xtal-trim.0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/audioinjector-wm8731-audio-overlay.dts +@@ -0,0 +1,39 @@ ++// Definitions for audioinjector.net audio add on soundcard ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ wm8731@1a { ++ #sound-dai-cells = <0>; ++ compatible = "wlf,wm8731"; ++ reg = <0x1a>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "ai,audioinjector-pi-soundcard"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/audremap-overlay.dts +@@ -0,0 +1,19 @@ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&audio_pins>; ++ frag0: __overlay__ { ++ brcm,pins = < 12 13 >; ++ brcm,function = < 4 >; /* alt0 alt0 */ ++ }; ++ }; ++ ++ __overrides__ { ++ swap_lr = <&frag0>, "swap_lr?"; ++ enable_jack = <&frag0>, "enable_jack?"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/bmp085_i2c-sensor-overlay.dts +@@ -0,0 +1,23 @@ ++// Definitions for BMP085/BMP180 digital barometric pressure and temperature sensors from Bosch Sensortec ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2c_arm>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ bmp085@77 { ++ compatible = "bosch,bmp085"; ++ reg = <0x77>; ++ default-oversampling = <3>; ++ status = "okay"; ++ }; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/dht11-overlay.dts +@@ -0,0 +1,39 @@ ++/* ++ * Overlay for the DHT11/21/22 humidity/temperature sensor modules. ++ */ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ ++ dht11: dht11@0 { ++ compatible = "dht11"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&dht11_pins>; ++ gpios = <&gpio 4 0>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ dht11_pins: dht11_pins { ++ brcm,pins = <4>; ++ brcm,function = <0>; // in ++ brcm,pull = <0>; // off ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ gpiopin = <&dht11_pins>,"brcm,pins:0", ++ <&dht11>,"gpios:4"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/dionaudio-loco-overlay.dts +@@ -0,0 +1,39 @@ ++// Definitions for Dion Audio LOCO DAC-AMP ++ ++/* ++ * PCM5242 DAC (in hardware mode) and TPA3118 AMP. ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/"; ++ __overlay__ { ++ pcm5102a-codec { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5102a"; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "dionaudio,loco-pcm5242-tpa3118"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/dpi18-overlay.dts +@@ -0,0 +1,31 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2708"; ++ ++ // There is no DPI driver module, but we need a platform device ++ // node (that doesn't already use pinctrl) to hang the pinctrl ++ // reference on - leds will do ++ ++ fragment@0 { ++ target = <&leds>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&dpi18_pins>; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ dpi18_pins: dpi18_pins { ++ brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11 ++ 12 13 14 15 16 17 18 19 20 ++ 21>; ++ brcm,function = <6>; /* alt2 */ ++ brcm,pull = <0>; /* no pull */ ++ }; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/dpi24-overlay.dts +@@ -0,0 +1,31 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2708"; ++ ++ // There is no DPI driver module, but we need a platform device ++ // node (that doesn't already use pinctrl) to hang the pinctrl ++ // reference on - leds will do ++ ++ fragment@0 { ++ target = <&leds>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&dpi24_pins>; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ dpi24_pins: dpi24_pins { ++ brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11 ++ 12 13 14 15 16 17 18 19 20 ++ 21 22 23 24 25 26 27>; ++ brcm,function = <6>; /* alt2 */ ++ brcm,pull = <0>; /* no pull */ ++ }; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/dwc-otg-overlay.dts +@@ -0,0 +1,20 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&usb>; ++ #address-cells = <1>; ++ #size-cells = <1>; ++ __overlay__ { ++ compatible = "brcm,bcm2708-usb"; ++ reg = <0x7e980000 0x10000>, ++ <0x7e006000 0x1000>; ++ interrupts = <2 0>, ++ <1 9>; ++ status = "okay"; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/dwc2-overlay.dts +@@ -0,0 +1,29 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&usb>; ++ #address-cells = <1>; ++ #size-cells = <1>; ++ dwc2_usb: __overlay__ { ++ compatible = "brcm,bcm2835-usb"; ++ reg = <0x7e980000 0x10000>; ++ interrupts = <1 9>; ++ dr_mode = "otg"; ++ g-np-tx-fifo-size = <32>; ++ g-rx-fifo-size = <256>; ++ g-tx-fifo-size = <256 128 128 64 64 64 32>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ dr_mode = <&dwc2_usb>, "dr_mode"; ++ g-np-tx-fifo-size = <&dwc2_usb>,"g-np-tx-fifo-size:0"; ++ g-rx-fifo-size = <&dwc2_usb>,"g-rx-fifo-size:0"; ++ g-tx-fifo-size = <&dwc2_usb>,"g-tx-fifo-size:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/enc28j60-overlay.dts +@@ -0,0 +1,53 @@ ++// Overlay for the Microchip ENC28J60 Ethernet Controller ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "okay"; ++ ++ eth1: enc28j60@0{ ++ compatible = "microchip,enc28j60"; ++ reg = <0>; /* CE0 */ ++ pinctrl-names = "default"; ++ pinctrl-0 = <ð1_pins>; ++ interrupt-parent = <&gpio>; ++ interrupts = <25 0x2>; /* falling edge */ ++ spi-max-frequency = <12000000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&gpio>; ++ __overlay__ { ++ eth1_pins: eth1_pins { ++ brcm,pins = <25>; ++ brcm,function = <0>; /* in */ ++ brcm,pull = <0>; /* none */ ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ int_pin = <ð1>, "interrupts:0", ++ <ð1_pins>, "brcm,pins:0"; ++ speed = <ð1>, "spi-max-frequency:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/enc28j60-spi2-overlay.dts +@@ -0,0 +1,47 @@ ++// Overlay for the Microchip ENC28J60 Ethernet Controller - SPI2 Compute Module ++// Interrupt pin: 39 ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&spi2>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "okay"; ++ ++ eth1: enc28j60@0{ ++ compatible = "microchip,enc28j60"; ++ reg = <0>; /* CE0 */ ++ pinctrl-names = "default"; ++ pinctrl-0 = <ð1_pins>; ++ interrupt-parent = <&gpio>; ++ interrupts = <39 0x2>; /* falling edge */ ++ spi-max-frequency = <12000000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ eth1_pins: eth1_pins { ++ brcm,pins = <39>; ++ brcm,function = <0>; /* in */ ++ brcm,pull = <0>; /* none */ ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ int_pin = <ð1>, "interrupts:0", ++ <ð1_pins>, "brcm,pins:0"; ++ speed = <ð1>, "spi-max-frequency:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/gpio-ir-overlay.dts +@@ -0,0 +1,44 @@ ++// Definitions for ir-gpio module ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ gpio_ir: ir-receiver { ++ compatible = "gpio-ir-receiver"; ++ ++ // pin number, high or low ++ gpios = <&gpio 18 1>; ++ ++ // parameter for keymap name ++ linux,rc-map-name = "rc-rc6-mce"; ++ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ gpio_ir_pins: gpio_ir_pins { ++ brcm,pins = <18>; // pin 18 ++ brcm,function = <0>; // in ++ brcm,pull = <1>; // down ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ // parameters ++ gpio_pin = <&gpio_ir>,"gpios:4", ++ <&gpio_ir_pins>,"brcm,pins:0"; // pin number ++ gpio_pull = <&gpio_ir_pins>,"brcm,pull:0"; // pull-up/down state ++ ++ rc-map-name = <&gpio_ir>,"linux,rc-map-name"; // default rc map ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/gpio-poweroff-overlay.dts +@@ -0,0 +1,34 @@ ++// Definitions for gpio-poweroff module ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ power_ctrl: power_ctrl { ++ compatible = "gpio-poweroff"; ++ gpios = <&gpio 26 0>; ++ force; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ power_ctrl_pins: power_ctrl_pins { ++ brcm,pins = <26>; ++ brcm,function = <1>; // out ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ gpiopin = <&power_ctrl>,"gpios:4", ++ <&power_ctrl_pins>,"brcm,pins:0"; ++ active_low = <&power_ctrl>,"gpios:8"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/hifiberry-amp-overlay.dts +@@ -0,0 +1,39 @@ ++// Definitions for HiFiBerry Amp/Amp+ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ tas5713@1b { ++ #sound-dai-cells = <0>; ++ compatible = "ti,tas5713"; ++ reg = <0x1b>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "hifiberry,hifiberry-amp"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/hifiberry-dac-overlay.dts +@@ -0,0 +1,34 @@ ++// Definitions for HiFiBerry DAC ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/"; ++ __overlay__ { ++ pcm5102a-codec { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5102a"; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "hifiberry,hifiberry-dac"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/hifiberry-dacplus-overlay.dts +@@ -0,0 +1,56 @@ ++// Definitions for HiFiBerry DAC+ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target-path = "/clocks"; ++ __overlay__ { ++ dacpro_osc: dacpro_osc { ++ compatible = "hifiberry,dacpro-clk"; ++ #clock-cells = <0>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcm5122@4d { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5122"; ++ reg = <0x4d>; ++ clocks = <&dacpro_osc>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&sound>; ++ hifiberry_dacplus: __overlay__ { ++ compatible = "hifiberry,hifiberry-dacplus"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ 24db_digital_gain = ++ <&hifiberry_dacplus>,"hifiberry,24db_digital_gain?"; ++ slave = <&hifiberry_dacplus>,"hifiberry-dacplus,slave?"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/hifiberry-digi-overlay.dts +@@ -0,0 +1,39 @@ ++// Definitions for HiFiBerry Digi ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ wm8804@3b { ++ #sound-dai-cells = <0>; ++ compatible = "wlf,wm8804"; ++ reg = <0x3b>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "hifiberry,hifiberry-digi"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/hifiberry-digi-pro-overlay.dts +@@ -0,0 +1,41 @@ ++// Definitions for HiFiBerry Digi Pro ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ wm8804@3b { ++ #sound-dai-cells = <0>; ++ compatible = "wlf,wm8804"; ++ reg = <0x3b>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "hifiberry,hifiberry-digi"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ clock44-gpio = <&gpio 5 0>; ++ clock48-gpio = <&gpio 6 0>; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/hy28a-overlay.dts +@@ -0,0 +1,93 @@ ++/* ++ * Device Tree overlay for HY28A display ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ hy28a_pins: hy28a_pins { ++ brcm,pins = <17 25 18>; ++ brcm,function = <0 1 1>; /* in out out */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ hy28a: hy28a@0{ ++ compatible = "ilitek,ili9320"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&hy28a_pins>; ++ ++ spi-max-frequency = <32000000>; ++ spi-cpol; ++ spi-cpha; ++ rotate = <270>; ++ bgr; ++ fps = <50>; ++ buswidth = <8>; ++ startbyte = <0x70>; ++ reset-gpios = <&gpio 25 0>; ++ led-gpios = <&gpio 18 1>; ++ debug = <0>; ++ }; ++ ++ hy28a_ts: hy28a-ts@1 { ++ compatible = "ti,ads7846"; ++ reg = <1>; ++ ++ spi-max-frequency = <2000000>; ++ interrupts = <17 2>; /* high-to-low edge triggered */ ++ interrupt-parent = <&gpio>; ++ pendown-gpio = <&gpio 17 0>; ++ ti,x-plate-ohms = /bits/ 16 <100>; ++ ti,pressure-max = /bits/ 16 <255>; ++ }; ++ }; ++ }; ++ __overrides__ { ++ speed = <&hy28a>,"spi-max-frequency:0"; ++ rotate = <&hy28a>,"rotate:0"; ++ fps = <&hy28a>,"fps:0"; ++ debug = <&hy28a>,"debug:0"; ++ xohms = <&hy28a_ts>,"ti,x-plate-ohms;0"; ++ resetgpio = <&hy28a>,"reset-gpios:4", ++ <&hy28a_pins>, "brcm,pins:1"; ++ ledgpio = <&hy28a>,"led-gpios:4", ++ <&hy28a_pins>, "brcm,pins:2"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/hy28b-overlay.dts +@@ -0,0 +1,148 @@ ++/* ++ * Device Tree overlay for HY28b display shield by Texy ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ hy28b_pins: hy28b_pins { ++ brcm,pins = <17 25 18>; ++ brcm,function = <0 1 1>; /* in out out */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ hy28b: hy28b@0{ ++ compatible = "ilitek,ili9325"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&hy28b_pins>; ++ ++ spi-max-frequency = <48000000>; ++ spi-cpol; ++ spi-cpha; ++ rotate = <270>; ++ bgr; ++ fps = <50>; ++ buswidth = <8>; ++ startbyte = <0x70>; ++ reset-gpios = <&gpio 25 0>; ++ led-gpios = <&gpio 18 1>; ++ ++ gamma = "04 1F 4 7 7 0 7 7 6 0\n0F 00 1 7 4 0 0 0 6 7"; ++ ++ init = <0x10000e7 0x0010 ++ 0x1000000 0x0001 ++ 0x1000001 0x0100 ++ 0x1000002 0x0700 ++ 0x1000003 0x1030 ++ 0x1000004 0x0000 ++ 0x1000008 0x0207 ++ 0x1000009 0x0000 ++ 0x100000a 0x0000 ++ 0x100000c 0x0001 ++ 0x100000d 0x0000 ++ 0x100000f 0x0000 ++ 0x1000010 0x0000 ++ 0x1000011 0x0007 ++ 0x1000012 0x0000 ++ 0x1000013 0x0000 ++ 0x2000032 ++ 0x1000010 0x1590 ++ 0x1000011 0x0227 ++ 0x2000032 ++ 0x1000012 0x009c ++ 0x2000032 ++ 0x1000013 0x1900 ++ 0x1000029 0x0023 ++ 0x100002b 0x000e ++ 0x2000032 ++ 0x1000020 0x0000 ++ 0x1000021 0x0000 ++ 0x2000032 ++ 0x1000050 0x0000 ++ 0x1000051 0x00ef ++ 0x1000052 0x0000 ++ 0x1000053 0x013f ++ 0x1000060 0xa700 ++ 0x1000061 0x0001 ++ 0x100006a 0x0000 ++ 0x1000080 0x0000 ++ 0x1000081 0x0000 ++ 0x1000082 0x0000 ++ 0x1000083 0x0000 ++ 0x1000084 0x0000 ++ 0x1000085 0x0000 ++ 0x1000090 0x0010 ++ 0x1000092 0x0000 ++ 0x1000093 0x0003 ++ 0x1000095 0x0110 ++ 0x1000097 0x0000 ++ 0x1000098 0x0000 ++ 0x1000007 0x0133 ++ 0x1000020 0x0000 ++ 0x1000021 0x0000 ++ 0x2000064>; ++ debug = <0>; ++ }; ++ ++ hy28b_ts: hy28b-ts@1 { ++ compatible = "ti,ads7846"; ++ reg = <1>; ++ ++ spi-max-frequency = <2000000>; ++ interrupts = <17 2>; /* high-to-low edge triggered */ ++ interrupt-parent = <&gpio>; ++ pendown-gpio = <&gpio 17 0>; ++ ti,x-plate-ohms = /bits/ 16 <100>; ++ ti,pressure-max = /bits/ 16 <255>; ++ }; ++ }; ++ }; ++ __overrides__ { ++ speed = <&hy28b>,"spi-max-frequency:0"; ++ rotate = <&hy28b>,"rotate:0"; ++ fps = <&hy28b>,"fps:0"; ++ debug = <&hy28b>,"debug:0"; ++ xohms = <&hy28b_ts>,"ti,x-plate-ohms;0"; ++ resetgpio = <&hy28b>,"reset-gpios:4", ++ <&hy28b_pins>, "brcm,pins:1"; ++ ledgpio = <&hy28b>,"led-gpios:4", ++ <&hy28b_pins>, "brcm,pins:2"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i2c-bcm2708-overlay.dts +@@ -0,0 +1,13 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2c_arm>; ++ __overlay__ { ++ compatible = "brcm,bcm2708-i2c"; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i2c-gpio-overlay.dts +@@ -0,0 +1,43 @@ ++// Overlay for i2c_gpio bitbanging host bus. ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ i2c_gpio: i2c@0 { ++ compatible = "i2c-gpio"; ++ gpios = <&gpio 23 0 /* sda */ ++ &gpio 24 0 /* scl */ ++ >; ++ i2c-gpio,delay-us = <2>; /* ~100 kHz */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/aliases"; ++ __overlay__ { ++ i2c_gpio = "/i2c@0"; ++ }; ++ }; ++ ++ fragment@2 { ++ target-path = "/__symbols__"; ++ __overlay__ { ++ i2c_gpio = "/i2c@0"; ++ }; ++ }; ++ ++ __overrides__ { ++ i2c_gpio_sda = <&i2c_gpio>,"gpios:4"; ++ i2c_gpio_scl = <&i2c_gpio>,"gpios:16"; ++ i2c_gpio_delay_us = <&i2c_gpio>,"i2c-gpio,delay-us:0"; ++ }; ++}; ++ +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i2c-mux-overlay.dts +@@ -0,0 +1,139 @@ ++// Umbrella I2C Mux overlay ++ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pca9542: mux@70 { ++ compatible = "nxp,pca9542"; ++ reg = <0x70>; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ i2c@0 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <0>; ++ }; ++ i2c@1 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <1>; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pca9545: mux@70 { ++ compatible = "nxp,pca9545"; ++ reg = <0x70>; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ i2c@0 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <0>; ++ }; ++ i2c@1 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <1>; ++ }; ++ i2c@2 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <2>; ++ }; ++ i2c@3 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <3>; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pca9548: mux@70 { ++ compatible = "nxp,pca9548"; ++ reg = <0x70>; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ i2c@0 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <0>; ++ }; ++ i2c@1 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <1>; ++ }; ++ i2c@2 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <2>; ++ }; ++ i2c@3 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <3>; ++ }; ++ i2c@4 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <4>; ++ }; ++ i2c@5 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <5>; ++ }; ++ i2c@6 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <6>; ++ }; ++ i2c@7 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <7>; ++ }; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ pca9542 = <0>, "+0"; ++ pca9545 = <0>, "+1"; ++ pca9548 = <0>, "+2"; ++ ++ addr = <&pca9542>,"reg:0", ++ <&pca9545>,"reg:0", ++ <&pca9548>,"reg:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i2c-pwm-pca9685a-overlay.dts +@@ -0,0 +1,26 @@ ++// Definitions for NXP PCA9685A I2C PWM controller on ARM I2C bus. ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2c_arm>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pca: pca@40 { ++ compatible = "nxp,pca9685"; ++ #pwm-cells = <2>; ++ reg = <0x40>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ __overrides__ { ++ addr = <&pca>,"reg:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts +@@ -0,0 +1,83 @@ ++// Definitions for several I2C based Real Time Clocks ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2c_arm>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ abx80x: abx80x@69 { ++ compatible = "abracon,abx80x"; ++ reg = <0x69>; ++ abracon,tc-diode = "standard"; ++ abracon,tc-resistor = <0>; ++ status = "disable"; ++ }; ++ ds1307: ds1307@68 { ++ compatible = "maxim,ds1307"; ++ reg = <0x68>; ++ status = "disable"; ++ }; ++ ds1339: ds1339@68 { ++ compatible = "dallas,ds1339"; ++ trickle-resistor-ohms = <0>; ++ reg = <0x68>; ++ status = "disable"; ++ }; ++ mcp7940x: mcp7940x@6f { ++ compatible = "microchip,mcp7940x"; ++ reg = <0x6f>; ++ status = "disable"; ++ }; ++ mcp7941x: mcp7941x@6f { ++ compatible = "microchip,mcp7941x"; ++ reg = <0x6f>; ++ status = "disable"; ++ }; ++ ds3231: ds3231@68 { ++ compatible = "maxim,ds3231"; ++ reg = <0x68>; ++ status = "disable"; ++ }; ++ pcf2127: pcf2127@51 { ++ compatible = "nxp,pcf2127"; ++ reg = <0x51>; ++ status = "disable"; ++ }; ++ pcf8523: pcf8523@68 { ++ compatible = "nxp,pcf8523"; ++ reg = <0x68>; ++ status = "disable"; ++ }; ++ pcf8563: pcf8563@51 { ++ compatible = "nxp,pcf8563"; ++ reg = <0x51>; ++ status = "disable"; ++ }; ++ }; ++ }; ++ __overrides__ { ++ abx80x = <&abx80x>,"status"; ++ ds1307 = <&ds1307>,"status"; ++ ds1339 = <&ds1339>,"status"; ++ ds3231 = <&ds3231>,"status"; ++ mcp7940x = <&mcp7940x>,"status"; ++ mcp7941x = <&mcp7941x>,"status"; ++ pcf2127 = <&pcf2127>,"status"; ++ pcf8523 = <&pcf8523>,"status"; ++ pcf8563 = <&pcf8563>,"status"; ++ trickle-diode-type = <&abx80x>,"abracon,tc-diode"; ++ trickle-resistor-ohms = <&ds1339>,"trickle-resistor-ohms:0", ++ <&abx80x>,"abracon,tc-resistor"; ++ wakeup-source = <&ds1339>,"wakeup-source?", ++ <&ds3231>,"wakeup-source?", ++ <&mcp7940x>,"wakeup-source?", ++ <&mcp7941x>,"wakeup-source?"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i2c-sensor-overlay.dts +@@ -0,0 +1,34 @@ ++// Definitions for a few digital barometric pressure and temperature sensors ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2c_arm>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ bmp085: bmp085@77 { ++ compatible = "bosch,bmp085"; ++ reg = <0x77>; ++ default-oversampling = <3>; ++ status = "disable"; ++ }; ++ ++ bmp280: bmp280@76 { ++ compatible = "bosch,bmp280"; ++ reg = <0x76>; ++ status = "disable"; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ bmp085 = <&bmp085>,"status"; ++ bmp280 = <&bmp280>,"status"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i2c0-bcm2708-overlay.dts +@@ -0,0 +1,61 @@ ++/* ++ * Device tree overlay for i2c_bcm2708, i2c0 bus ++ * ++ * Compile: ++ * dtc -@ -I dts -O dtb -o i2c0-bcm2708-overlay.dtb i2c0-bcm2708-overlay.dts ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2c0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c0_pins>; ++ frag1: __overlay__ { ++ brcm,pins = <0 1>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c0_pins>; ++ __dormant__ { ++ brcm,pins = <28 29>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&i2c0_pins>; ++ __dormant__ { ++ brcm,pins = <44 45>; ++ brcm,function = <5>; /* alt1 */ ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&i2c0_pins>; ++ __dormant__ { ++ brcm,pins = <46 47>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ }; ++ ++ __overrides__ { ++ sda0_pin = <&frag1>,"brcm,pins:0"; ++ scl0_pin = <&frag1>,"brcm,pins:4"; ++ pins_0_1 = <0>,"+1-2-3-4"; ++ pins_28_29 = <0>,"-1+2-3-4"; ++ pins_44_45 = <0>,"-1-2+3-4"; ++ pins_46_47 = <0>,"-1-2-3+4"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i2c1-bcm2708-overlay.dts +@@ -0,0 +1,37 @@ ++/* ++ * Device tree overlay for i2c_bcm2708, i2c1 bus ++ * ++ * Compile: ++ * dtc -@ -I dts -O dtb -o i2c1-bcm2708-overlay.dtb i2c1-bcm2708-overlay.dts ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2c1>; ++ __overlay__ { ++ pinctrl-0 = <&i2c1_pins>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ i2c1_pins: i2c1 { ++ brcm,pins = <2 3>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ sda1_pin = <&i2c1_pins>,"brcm,pins:0"; ++ scl1_pin = <&i2c1_pins>,"brcm,pins:4"; ++ pin_func = <&i2c1_pins>,"brcm,function:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i2s-gpio28-31-overlay.dts +@@ -0,0 +1,18 @@ ++/* ++ * Device tree overlay to move i2s to gpio 28 to 31 on CM ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&i2s_pins>; ++ __overlay__ { ++ brcm,pins = <28 29 30 31>; ++ brcm,function = <6>; /* alt2 */ ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/iqaudio-dac-overlay.dts +@@ -0,0 +1,43 @@ ++// Definitions for IQaudIO DAC ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcm5122@4c { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5122"; ++ reg = <0x4c>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ frag2: __overlay__ { ++ compatible = "iqaudio,iqaudio-dac"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ 24db_digital_gain = <&frag2>,"iqaudio,24db_digital_gain?"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/iqaudio-dacplus-overlay.dts +@@ -0,0 +1,46 @@ ++// Definitions for IQaudIO DAC+ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcm5122@4c { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5122"; ++ reg = <0x4c>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ iqaudio_dac: __overlay__ { ++ compatible = "iqaudio,iqaudio-dac"; ++ i2s-controller = <&i2s>; ++ mute-gpios = <&gpio 22 0>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ 24db_digital_gain = <&iqaudio_dac>,"iqaudio,24db_digital_gain?"; ++ auto_mute_amp = <&iqaudio_dac>,"iqaudio-dac,auto-mute-amp?"; ++ unmute_amp = <&iqaudio_dac>,"iqaudio-dac,unmute-amp?"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/iqaudio-digi-wm8804-audio-overlay.dts +@@ -0,0 +1,47 @@ ++// Definitions for IQAudIO Digi WM8804 audio board ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ wm8804@3b { ++ #sound-dai-cells = <0>; ++ compatible = "wlf,wm8804"; ++ reg = <0x3b>; ++ status = "okay"; ++ // DVDD-supply = <®_3v3>; ++ // PVDD-supply = <®_3v3>; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ wm8804_digi: __overlay__ { ++ compatible = "iqaudio,wm8804-digi"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ card_name = <&wm8804_digi>,"wm8804-digi,card-name"; ++ dai_name = <&wm8804_digi>,"wm8804-digi,dai-name"; ++ dai_stream_name = <&wm8804_digi>,"wm8804-digi,dai-stream-name"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/justboom-dac-overlay.dts +@@ -0,0 +1,43 @@ ++// Definitions for JustBoom DAC ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcm5122@4d { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5122"; ++ reg = <0x4d>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ frag2: __overlay__ { ++ compatible = "justboom,justboom-dac"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ 24db_digital_gain = <&frag2>,"justboom,24db_digital_gain?"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/justboom-digi-overlay.dts +@@ -0,0 +1,39 @@ ++// Definitions for JustBoom Digi ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ wm8804@3b { ++ #sound-dai-cells = <0>; ++ compatible = "wlf,wm8804"; ++ reg = <0x3b>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "justboom,justboom-digi"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/lirc-rpi-overlay.dts +@@ -0,0 +1,57 @@ ++// Definitions for lirc-rpi module ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ lirc_rpi: lirc_rpi { ++ compatible = "rpi,lirc-rpi"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&lirc_pins>; ++ status = "okay"; ++ ++ // Override autodetection of IR receiver circuit ++ // (0 = active high, 1 = active low, -1 = no override ) ++ rpi,sense = <0xffffffff>; ++ ++ // Software carrier ++ // (0 = off, 1 = on) ++ rpi,softcarrier = <1>; ++ ++ // Invert output ++ // (0 = off, 1 = on) ++ rpi,invert = <0>; ++ ++ // Enable debugging messages ++ // (0 = off, 1 = on) ++ rpi,debug = <0>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ lirc_pins: lirc_pins { ++ brcm,pins = <17 18>; ++ brcm,function = <1 0>; // out in ++ brcm,pull = <0 1>; // off down ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ gpio_out_pin = <&lirc_pins>,"brcm,pins:0"; ++ gpio_in_pin = <&lirc_pins>,"brcm,pins:4"; ++ gpio_in_pull = <&lirc_pins>,"brcm,pull:4"; ++ ++ sense = <&lirc_rpi>,"rpi,sense:0"; ++ softcarrier = <&lirc_rpi>,"rpi,softcarrier:0"; ++ invert = <&lirc_rpi>,"rpi,invert:0"; ++ debug = <&lirc_rpi>,"rpi,debug:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/mcp23017-overlay.dts +@@ -0,0 +1,54 @@ ++// Definitions for MCP23017 Gpio Extender from Microchip Semiconductor ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&i2c1>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ mcp23017_pins: mcp23017_pins { ++ brcm,pins = <4>; ++ brcm,function = <0>; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ mcp23017: mcp@20 { ++ compatible = "microchip,mcp23017"; ++ reg = <0x20>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells=<2>; ++ interrupt-parent = <&gpio>; ++ interrupts = <4 2>; ++ interrupt-controller; ++ microchip,irq-mirror; ++ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ gpiopin = <&mcp23017_pins>,"brcm,pins:0", ++ <&mcp23017>,"interrupts:0"; ++ addr = <&mcp23017>,"reg:0"; ++ }; ++}; ++ +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/mcp23s17-overlay.dts +@@ -0,0 +1,732 @@ ++// Overlay for MCP23S08/17 GPIO Extenders from Microchip Semiconductor ++ ++// dtparams: ++// s08-spi--present - 4-bit integer, bitmap indicating MCP23S08 devices present on SPI, CS#. ++// s17-spi--present - 8-bit integer, bitmap indicating MCP23S17 devices present on SPI, CS#. ++// s08-spi--int-gpio - integer, enables interrupts on a single MCP23S08 device on SPI, CS#, specifies the GPIO pin to which INT output is connected. ++// s17-spi--int-gpio - integer, enables mirrored interrupts on a single MCP23S17 device on SPI, CS#, specifies the GPIO pin to which either INTA or INTB output is connected. ++// ++// If devices are present on SPI1 or SPI2, those interfaces must be enabled with one of the spi1-1/2/3cs and/or spi2-1/2/3cs overlays. ++// If interrupts are enabled for a device on a given CS# on a SPI bus, that device must be the only one present on that SPI bus/CS#. ++// ++// Example 1: A single MCP23S17 device on SPI0, CS#0 with its SPI addr set to 0 and INTA output connected to GPIO25: ++// dtoverlay=mcp23s17:s17-spi0-0-present=1,s17-spi0-0-int-gpio=25 ++// ++// Example 2: Two MCP23S08 devices on SPI1, CS#0 with their addrs set to 2 and 3. Three MCP23S17 devices on SPI1, CS#1 with their addrs set to 0, 1 and 7: ++// dtoverlay=spi1-2cs ++// dtoverlay=mcp23s17:s08-spi1-0-present=12,s17-spi1-1-present=131 ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ // disable spi-dev on spi0.0 ++ fragment@0 { ++ target = <&spidev0>; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // disable spi-dev on spi0.1 ++ fragment@1 { ++ target = <&spidev1>; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // disable spi-dev on spi1.0 ++ fragment@2 { ++ target-path = "spi1/spidev@0"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // disable spi-dev on spi1.1 ++ fragment@3 { ++ target-path = "spi1/spidev@1"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // disable spi-dev on spi1.2 ++ fragment@4 { ++ target-path = "spi1/spidev@2"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // disable spi-dev on spi2.0 ++ fragment@5 { ++ target-path = "spi2/spidev@0"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // disable spi-dev on spi2.1 ++ fragment@6 { ++ target-path = "spi2/spidev@1"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // disable spi-dev on spi2.2 ++ fragment@7 { ++ target-path = "spi2/spidev@2"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // enable one or more mcp23s08s on spi0.0 ++ fragment@8 { ++ target = <&spi0>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s08_00: mcp23s08@0 { ++ compatible = "microchip,mcp23s08"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi0-0-present parameter */ ++ reg = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi0-0-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s08s on spi0.1 ++ fragment@9 { ++ target = <&spi0>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s08_01: mcp23s08@1 { ++ compatible = "microchip,mcp23s08"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi0-1-present parameter */ ++ reg = <1>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi0-1-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s08s on spi1.0 ++ fragment@10 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s08_10: mcp23s08@0 { ++ compatible = "microchip,mcp23s08"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi1-0-present parameter */ ++ reg = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi1-0-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s08s on spi1.1 ++ fragment@11 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s08_11: mcp23s08@1 { ++ compatible = "microchip,mcp23s08"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi1-1-present parameter */ ++ reg = <1>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi1-1-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s08s on spi1.2 ++ fragment@12 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s08_12: mcp23s08@2 { ++ compatible = "microchip,mcp23s08"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi1-2-present parameter */ ++ reg = <2>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi1-2-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s08s on spi2.0 ++ fragment@13 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s08_20: mcp23s08@0 { ++ compatible = "microchip,mcp23s08"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi2-0-present parameter */ ++ reg = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi2-0-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s08s on spi2.1 ++ fragment@14 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s08_21: mcp23s08@1 { ++ compatible = "microchip,mcp23s08"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi2-1-present parameter */ ++ reg = <1>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi2-1-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s08s on spi2.2 ++ fragment@15 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s08_22: mcp23s08@2 { ++ compatible = "microchip,mcp23s08"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi2-2-present parameter */ ++ reg = <2>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi2-2-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s17s on spi0.0 ++ fragment@16 { ++ target = <&spi0>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s17_00: mcp23s17@0 { ++ compatible = "microchip,mcp23s17"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi0-0-present parameter */ ++ reg = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi0-0-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s17s on spi0.1 ++ fragment@17 { ++ target = <&spi0>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s17_01: mcp23s17@1 { ++ compatible = "microchip,mcp23s17"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi0-1-present parameter */ ++ reg = <1>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi0-1-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s17s on spi1.0 ++ fragment@18 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s17_10: mcp23s17@0 { ++ compatible = "microchip,mcp23s17"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi1-0-present parameter */ ++ reg = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi1-0-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s17s on spi1.1 ++ fragment@19 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s17_11: mcp23s17@1 { ++ compatible = "microchip,mcp23s17"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi1-1-present parameter */ ++ reg = <1>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi1-1-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s17s on spi1.2 ++ fragment@20 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s17_12: mcp23s17@2 { ++ compatible = "microchip,mcp23s17"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi1-2-present parameter */ ++ reg = <2>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi1-2-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s17s on spi2.0 ++ fragment@21 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s17_20: mcp23s17@0 { ++ compatible = "microchip,mcp23s17"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi2-0-present parameter */ ++ reg = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi2-0-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s17s on spi2.1 ++ fragment@22 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s17_21: mcp23s17@1 { ++ compatible = "microchip,mcp23s17"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi2-1-present parameter */ ++ reg = <1>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi2-1-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s17s on spi2.2 ++ fragment@23 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s17_22: mcp23s17@2 { ++ compatible = "microchip,mcp23s17"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi2-2-present parameter */ ++ reg = <2>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi2-2-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi0.0 as a input with no pull-up/down ++ fragment@24 { ++ target = <&gpio>; ++ __dormant__ { ++ spi0_0_int_pins: spi0_0_int_pins { ++ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi0-0-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi0.1 as a input with no pull-up/down ++ fragment@25 { ++ target = <&gpio>; ++ __dormant__ { ++ spi0_1_int_pins: spi0_1_int_pins { ++ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi0-1-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi1.0 as a input with no pull-up/down ++ fragment@26 { ++ target = <&gpio>; ++ __dormant__ { ++ spi1_0_int_pins: spi1_0_int_pins { ++ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi1-0-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi1.1 as a input with no pull-up/down ++ fragment@27 { ++ target = <&gpio>; ++ __dormant__ { ++ spi1_1_int_pins: spi1_1_int_pins { ++ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi1-1-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi1.2 as a input with no pull-up/down ++ fragment@28 { ++ target = <&gpio>; ++ __dormant__ { ++ spi1_2_int_pins: spi1_2_int_pins { ++ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi1-2-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi2.0 as a input with no pull-up/down ++ fragment@29 { ++ target = <&gpio>; ++ __dormant__ { ++ spi2_0_int_pins: spi2_0_int_pins { ++ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi2-0-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi2.1 as a input with no pull-up/down ++ fragment@30 { ++ target = <&gpio>; ++ __dormant__ { ++ spi2_1_int_pins: spi2_1_int_pins { ++ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi2-1-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi2.2 as a input with no pull-up/down ++ fragment@31 { ++ target = <&gpio>; ++ __dormant__ { ++ spi2_2_int_pins: spi2_2_int_pins { ++ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi2-2-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s08 on spi0.0. ++ // Use default active low interrupt signalling. ++ fragment@32 { ++ target = <&mcp23s08_00>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s08 on spi0.1. ++ // Use default active low interrupt signalling. ++ fragment@33 { ++ target = <&mcp23s08_01>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s08 on spi1.0. ++ // Use default active low interrupt signalling. ++ fragment@34 { ++ target = <&mcp23s08_10>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s08 on spi1.1. ++ // Use default active low interrupt signalling. ++ fragment@35 { ++ target = <&mcp23s08_11>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s08 on spi1.2. ++ // Use default active low interrupt signalling. ++ fragment@36 { ++ target = <&mcp23s08_12>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s08 on spi2.0. ++ // Use default active low interrupt signalling. ++ fragment@37 { ++ target = <&mcp23s08_20>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s08 on spi2.1. ++ // Use default active low interrupt signalling. ++ fragment@38 { ++ target = <&mcp23s08_21>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s08 on spi2.2. ++ // Use default active low interrupt signalling. ++ fragment@39 { ++ target = <&mcp23s08_22>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s17 on spi0.0. ++ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin. ++ // Use default active low interrupt signalling. ++ fragment@40 { ++ target = <&mcp23s17_00>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ microchip,irq-mirror; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s17 on spi0.1. ++ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin. ++ // Configure INTA/B outputs of mcp23s08/17 as active low. ++ fragment@41 { ++ target = <&mcp23s17_01>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ microchip,irq-mirror; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s17 on spi1.0. ++ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin. ++ // Configure INTA/B outputs of mcp23s08/17 as active low. ++ fragment@42 { ++ target = <&mcp23s17_10>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ microchip,irq-mirror; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s17 on spi1.1. ++ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin. ++ // Configure INTA/B outputs of mcp23s08/17 as active low. ++ fragment@43 { ++ target = <&mcp23s17_11>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ microchip,irq-mirror; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s17 on spi1.2. ++ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin. ++ // Configure INTA/B outputs of mcp23s08/17 as active low. ++ fragment@44 { ++ target = <&mcp23s17_12>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ microchip,irq-mirror; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s17 on spi2.0. ++ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin. ++ // Configure INTA/B outputs of mcp23s08/17 as active low. ++ fragment@45 { ++ target = <&mcp23s17_20>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ microchip,irq-mirror; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s17 on spi2.1. ++ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin. ++ // Configure INTA/B outputs of mcp23s08/17 as active low. ++ fragment@46 { ++ target = <&mcp23s17_21>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ microchip,irq-mirror; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s17 on spi2.2. ++ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin. ++ // Configure INTA/B outputs of mcp23s08/17 as active low. ++ fragment@47 { ++ target = <&mcp23s17_22>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ microchip,irq-mirror; ++ }; ++ }; ++ ++ __overrides__ { ++ s08-spi0-0-present = <0>,"+0+8", <&mcp23s08_00>,"microchip,spi-present-mask:0"; ++ s08-spi0-1-present = <0>,"+1+9", <&mcp23s08_01>,"microchip,spi-present-mask:0"; ++ s08-spi1-0-present = <0>,"+2+10", <&mcp23s08_10>,"microchip,spi-present-mask:0"; ++ s08-spi1-1-present = <0>,"+3+11", <&mcp23s08_11>,"microchip,spi-present-mask:0"; ++ s08-spi1-2-present = <0>,"+4+12", <&mcp23s08_12>,"microchip,spi-present-mask:0"; ++ s08-spi2-0-present = <0>,"+5+13", <&mcp23s08_20>,"microchip,spi-present-mask:0"; ++ s08-spi2-1-present = <0>,"+6+14", <&mcp23s08_21>,"microchip,spi-present-mask:0"; ++ s08-spi2-2-present = <0>,"+7+15", <&mcp23s08_22>,"microchip,spi-present-mask:0"; ++ s17-spi0-0-present = <0>,"+0+16", <&mcp23s17_00>,"microchip,spi-present-mask:0"; ++ s17-spi0-1-present = <0>,"+1+17", <&mcp23s17_01>,"microchip,spi-present-mask:0"; ++ s17-spi1-0-present = <0>,"+2+18", <&mcp23s17_10>,"microchip,spi-present-mask:0"; ++ s17-spi1-1-present = <0>,"+3+19", <&mcp23s17_11>,"microchip,spi-present-mask:0"; ++ s17-spi1-2-present = <0>,"+4+20", <&mcp23s17_12>,"microchip,spi-present-mask:0"; ++ s17-spi2-0-present = <0>,"+5+21", <&mcp23s17_20>,"microchip,spi-present-mask:0"; ++ s17-spi2-1-present = <0>,"+6+22", <&mcp23s17_21>,"microchip,spi-present-mask:0"; ++ s17-spi2-2-present = <0>,"+7+23", <&mcp23s17_22>,"microchip,spi-present-mask:0"; ++ s08-spi0-0-int-gpio = <0>,"+24+32", <&spi0_0_int_pins>,"brcm,pins:0", <&mcp23s08_00>,"interrupts:0"; ++ s08-spi0-1-int-gpio = <0>,"+25+33", <&spi0_1_int_pins>,"brcm,pins:0", <&mcp23s08_01>,"interrupts:0"; ++ s08-spi1-0-int-gpio = <0>,"+26+34", <&spi1_0_int_pins>,"brcm,pins:0", <&mcp23s08_10>,"interrupts:0"; ++ s08-spi1-1-int-gpio = <0>,"+27+35", <&spi1_1_int_pins>,"brcm,pins:0", <&mcp23s08_11>,"interrupts:0"; ++ s08-spi1-2-int-gpio = <0>,"+28+36", <&spi1_2_int_pins>,"brcm,pins:0", <&mcp23s08_12>,"interrupts:0"; ++ s08-spi2-0-int-gpio = <0>,"+29+37", <&spi2_0_int_pins>,"brcm,pins:0", <&mcp23s08_20>,"interrupts:0"; ++ s08-spi2-1-int-gpio = <0>,"+30+38", <&spi2_1_int_pins>,"brcm,pins:0", <&mcp23s08_21>,"interrupts:0"; ++ s08-spi2-2-int-gpio = <0>,"+31+39", <&spi2_2_int_pins>,"brcm,pins:0", <&mcp23s08_22>,"interrupts:0"; ++ s17-spi0-0-int-gpio = <0>,"+24+40", <&spi0_0_int_pins>,"brcm,pins:0", <&mcp23s17_00>,"interrupts:0"; ++ s17-spi0-1-int-gpio = <0>,"+25+41", <&spi0_1_int_pins>,"brcm,pins:0", <&mcp23s17_01>,"interrupts:0"; ++ s17-spi1-0-int-gpio = <0>,"+26+42", <&spi1_0_int_pins>,"brcm,pins:0", <&mcp23s17_10>,"interrupts:0"; ++ s17-spi1-1-int-gpio = <0>,"+27+43", <&spi1_1_int_pins>,"brcm,pins:0", <&mcp23s17_11>,"interrupts:0"; ++ s17-spi1-2-int-gpio = <0>,"+28+44", <&spi1_2_int_pins>,"brcm,pins:0", <&mcp23s17_12>,"interrupts:0"; ++ s17-spi2-0-int-gpio = <0>,"+29+45", <&spi2_0_int_pins>,"brcm,pins:0", <&mcp23s17_20>,"interrupts:0"; ++ s17-spi2-1-int-gpio = <0>,"+30+46", <&spi2_1_int_pins>,"brcm,pins:0", <&mcp23s17_21>,"interrupts:0"; ++ s17-spi2-2-int-gpio = <0>,"+31+47", <&spi2_2_int_pins>,"brcm,pins:0", <&mcp23s17_22>,"interrupts:0"; ++ }; ++}; ++ +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/mcp2515-can0-overlay.dts +@@ -0,0 +1,73 @@ ++/* ++ * Device tree overlay for mcp251x/can0 on spi0.0 ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709"; ++ /* disable spi-dev for spi0.0 */ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ /* the interrupt pin of the can-controller */ ++ fragment@2 { ++ target = <&gpio>; ++ __overlay__ { ++ can0_pins: can0_pins { ++ brcm,pins = <25>; ++ brcm,function = <0>; /* input */ ++ }; ++ }; ++ }; ++ ++ /* the clock/oscillator of the can-controller */ ++ fragment@3 { ++ target-path = "/clocks"; ++ __overlay__ { ++ /* external oscillator of mcp2515 on SPI0.0 */ ++ can0_osc: can0_osc { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <16000000>; ++ }; ++ }; ++ }; ++ ++ /* the spi config of the can-controller itself binding everything together */ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ can0: mcp2515@0 { ++ reg = <0>; ++ compatible = "microchip,mcp2515"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&can0_pins>; ++ spi-max-frequency = <10000000>; ++ interrupt-parent = <&gpio>; ++ interrupts = <25 0x2>; ++ clocks = <&can0_osc>; ++ }; ++ }; ++ }; ++ __overrides__ { ++ oscillator = <&can0_osc>,"clock-frequency:0"; ++ spimaxfrequency = <&can0>,"spi-max-frequency:0"; ++ interrupt = <&can0_pins>,"brcm,pins:0",<&can0>,"interrupts:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/mcp2515-can1-overlay.dts +@@ -0,0 +1,73 @@ ++/* ++ * Device tree overlay for mcp251x/can1 on spi0.1 edited by petit_miner ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709"; ++ /* disable spi-dev for spi0.1 */ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ /* the interrupt pin of the can-controller */ ++ fragment@2 { ++ target = <&gpio>; ++ __overlay__ { ++ can1_pins: can1_pins { ++ brcm,pins = <25>; ++ brcm,function = <0>; /* input */ ++ }; ++ }; ++ }; ++ ++ /* the clock/oscillator of the can-controller */ ++ fragment@3 { ++ target-path = "/clocks"; ++ __overlay__ { ++ /* external oscillator of mcp2515 on spi0.1 */ ++ can1_osc: can1_osc { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <16000000>; ++ }; ++ }; ++ }; ++ ++ /* the spi config of the can-controller itself binding everything together */ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ can1: mcp2515@1 { ++ reg = <1>; ++ compatible = "microchip,mcp2515"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&can1_pins>; ++ spi-max-frequency = <10000000>; ++ interrupt-parent = <&gpio>; ++ interrupts = <25 0x2>; ++ clocks = <&can1_osc>; ++ }; ++ }; ++ }; ++ __overrides__ { ++ oscillator = <&can1_osc>,"clock-frequency:0"; ++ spimaxfrequency = <&can1>,"spi-max-frequency:0"; ++ interrupt = <&can1_pins>,"brcm,pins:0",<&can1>,"interrupts:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/midi-uart0-overlay.dts +@@ -0,0 +1,36 @@ ++/dts-v1/; ++/plugin/; ++ ++#include ++ ++/* ++ * Fake a higher clock rate to get a larger divisor, and thereby a lower ++ * baudrate. The real clock is 48MHz, which we scale so that requesting ++ * 38.4kHz results in an actual 31.25kHz. ++ * ++ * 48000000*38400/31250 = 58982400 ++ */ ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/clocks"; ++ __overlay__ { ++ midi_clk: midi_clk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-output-names = "uart0_pclk"; ++ clock-frequency = <58982400>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&uart0>; ++ __overlay__ { ++ clocks = <&midi_clk>, ++ <&clocks BCM2835_CLOCK_VPU>; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/mmc-overlay.dts +@@ -0,0 +1,38 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&mmc>; ++ frag0: __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&mmc_pins>; ++ bus-width = <4>; ++ brcm,overclock-50 = <0>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ mmc_pins: mmc_pins { ++ brcm,pins = <48 49 50 51 52 53>; ++ brcm,function = <7>; /* alt3 */ ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sdhost>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ __overrides__ { ++ overclock_50 = <&frag0>,"brcm,overclock-50:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/mz61581-overlay.dts +@@ -0,0 +1,117 @@ ++/* ++ * Device Tree overlay for MZ61581-PI-EXT 2014.12.28 by Tontec ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ mz61581_pins: mz61581_pins { ++ brcm,pins = <4 15 18 25>; ++ brcm,function = <0 1 1 1>; /* in out out out */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ mz61581: mz61581@0{ ++ compatible = "samsung,s6d02a1"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&mz61581_pins>; ++ ++ spi-max-frequency = <128000000>; ++ spi-cpol; ++ spi-cpha; ++ ++ width = <320>; ++ height = <480>; ++ rotate = <270>; ++ bgr; ++ fps = <30>; ++ buswidth = <8>; ++ txbuflen = <32768>; ++ ++ reset-gpios = <&gpio 15 0>; ++ dc-gpios = <&gpio 25 0>; ++ led-gpios = <&gpio 18 0>; ++ ++ init = <0x10000b0 00 ++ 0x1000011 ++ 0x20000ff ++ 0x10000b3 0x02 0x00 0x00 0x00 ++ 0x10000c0 0x13 0x3b 0x00 0x02 0x00 0x01 0x00 0x43 ++ 0x10000c1 0x08 0x16 0x08 0x08 ++ 0x10000c4 0x11 0x07 0x03 0x03 ++ 0x10000c6 0x00 ++ 0x10000c8 0x03 0x03 0x13 0x5c 0x03 0x07 0x14 0x08 0x00 0x21 0x08 0x14 0x07 0x53 0x0c 0x13 0x03 0x03 0x21 0x00 ++ 0x1000035 0x00 ++ 0x1000036 0xa0 ++ 0x100003a 0x55 ++ 0x1000044 0x00 0x01 ++ 0x10000d0 0x07 0x07 0x1d 0x03 ++ 0x10000d1 0x03 0x30 0x10 ++ 0x10000d2 0x03 0x14 0x04 ++ 0x1000029 ++ 0x100002c>; ++ ++ /* This is a workaround to make sure the init sequence slows down and doesn't fail */ ++ debug = <3>; ++ }; ++ ++ mz61581_ts: mz61581_ts@1 { ++ compatible = "ti,ads7846"; ++ reg = <1>; ++ ++ spi-max-frequency = <2000000>; ++ interrupts = <4 2>; /* high-to-low edge triggered */ ++ interrupt-parent = <&gpio>; ++ pendown-gpio = <&gpio 4 0>; ++ ++ ti,x-plate-ohms = /bits/ 16 <60>; ++ ti,pressure-max = /bits/ 16 <255>; ++ }; ++ }; ++ }; ++ __overrides__ { ++ speed = <&mz61581>, "spi-max-frequency:0"; ++ rotate = <&mz61581>, "rotate:0"; ++ fps = <&mz61581>, "fps:0"; ++ txbuflen = <&mz61581>, "txbuflen:0"; ++ debug = <&mz61581>, "debug:0"; ++ xohms = <&mz61581_ts>,"ti,x-plate-ohms;0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/pi3-act-led-overlay.dts +@@ -0,0 +1,27 @@ ++/dts-v1/; ++/plugin/; ++ ++/* Pi3 uses a GPIO expander to drive the LEDs which can only be accessed ++ from the VPU. There is a special driver for this with a separate DT node, ++ which has the unfortunate consequence of breaking the act_led_gpio and ++ act_led_activelow dtparams. ++ ++ This overlay changes the GPIO controller back to the standard one and ++ restores the dtparams. ++*/ ++ ++/{ ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&act_led>; ++ frag0: __overlay__ { ++ gpios = <&gpio 0 0>; ++ }; ++ }; ++ ++ __overrides__ { ++ gpio = <&frag0>,"gpios:4"; ++ activelow = <&frag0>,"gpios:8"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/pi3-disable-bt-overlay.dts +@@ -0,0 +1,46 @@ ++/dts-v1/; ++/plugin/; ++ ++/* Disable Bluetooth and restore UART0/ttyAMA0 over GPIOs 14 & 15. ++ To disable the systemd service that initialises the modem so it doesn't use ++ the UART: ++ ++ sudo systemctl disable hciuart ++*/ ++ ++/{ ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&uart1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&uart0>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart0_pins>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&uart0_pins>; ++ __overlay__ { ++ brcm,pins; ++ brcm,function; ++ brcm,pull; ++ }; ++ }; ++ ++ fragment@3 { ++ target-path = "/aliases"; ++ __overlay__ { ++ serial0 = "/soc/serial@7e201000"; ++ serial1 = "/soc/serial@7e215040"; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts +@@ -0,0 +1,64 @@ ++/dts-v1/; ++/plugin/; ++ ++/* Switch Pi3 Bluetooth function to use the mini-UART (ttyS0) and restore ++ UART0/ttyAMA0 over GPIOs 14 & 15. Note that this may reduce the maximum ++ usable baudrate. ++ ++ It is also necessary to edit /lib/systemd/system/hciuart.service and ++ replace ttyAMA0 with ttyS0, unless you have a system with udev rules ++ that create /dev/serial0 and /dev/serial1, in which case use /dev/serial1 ++ instead because it will always be correct. ++ ++ If cmdline.txt uses the alias serial0 to refer to the user-accessable port ++ then the firmware will replace with the appropriate port whether or not ++ this overlay is used. ++*/ ++ ++/{ ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&uart0>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart0_pins>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&uart1>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart1_pins &bt_pins>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&uart0_pins>; ++ __overlay__ { ++ brcm,pins; ++ brcm,function; ++ brcm,pull; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&uart1_pins>; ++ __overlay__ { ++ brcm,pins = <32 33>; ++ brcm,function = <2>; /* alt5=UART1 */ ++ brcm,pull = <0 2>; ++ }; ++ }; ++ ++ fragment@4 { ++ target-path = "/aliases"; ++ __overlay__ { ++ serial0 = "/soc/serial@7e201000"; ++ serial1 = "/soc/serial@7e215040"; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/piscreen-overlay.dts +@@ -0,0 +1,102 @@ ++/* ++ * Device Tree overlay for PiScreen 3.5" display shield by Ozzmaker ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ piscreen_pins: piscreen_pins { ++ brcm,pins = <17 25 24 22>; ++ brcm,function = <0 1 1 1>; /* in out out out */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ piscreen: piscreen@0{ ++ compatible = "ilitek,ili9486"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&piscreen_pins>; ++ ++ spi-max-frequency = <24000000>; ++ rotate = <270>; ++ bgr; ++ fps = <30>; ++ buswidth = <8>; ++ regwidth = <16>; ++ reset-gpios = <&gpio 25 0>; ++ dc-gpios = <&gpio 24 0>; ++ led-gpios = <&gpio 22 1>; ++ debug = <0>; ++ ++ init = <0x10000b0 0x00 ++ 0x1000011 ++ 0x20000ff ++ 0x100003a 0x55 ++ 0x1000036 0x28 ++ 0x10000c2 0x44 ++ 0x10000c5 0x00 0x00 0x00 0x00 ++ 0x10000e0 0x0f 0x1f 0x1c 0x0c 0x0f 0x08 0x48 0x98 0x37 0x0a 0x13 0x04 0x11 0x0d 0x00 ++ 0x10000e1 0x0f 0x32 0x2e 0x0b 0x0d 0x05 0x47 0x75 0x37 0x06 0x10 0x03 0x24 0x20 0x00 ++ 0x10000e2 0x0f 0x32 0x2e 0x0b 0x0d 0x05 0x47 0x75 0x37 0x06 0x10 0x03 0x24 0x20 0x00 ++ 0x1000011 ++ 0x1000029>; ++ }; ++ ++ piscreen_ts: piscreen-ts@1 { ++ compatible = "ti,ads7846"; ++ reg = <1>; ++ ++ spi-max-frequency = <2000000>; ++ interrupts = <17 2>; /* high-to-low edge triggered */ ++ interrupt-parent = <&gpio>; ++ pendown-gpio = <&gpio 17 0>; ++ ti,swap-xy; ++ ti,x-plate-ohms = /bits/ 16 <100>; ++ ti,pressure-max = /bits/ 16 <255>; ++ }; ++ }; ++ }; ++ __overrides__ { ++ speed = <&piscreen>,"spi-max-frequency:0"; ++ rotate = <&piscreen>,"rotate:0"; ++ fps = <&piscreen>,"fps:0"; ++ debug = <&piscreen>,"debug:0"; ++ xohms = <&piscreen_ts>,"ti,x-plate-ohms;0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/piscreen2r-overlay.dts +@@ -0,0 +1,106 @@ ++ /* ++ * Device Tree overlay for PiScreen2 3.5" TFT with resistive touch by Ozzmaker.com ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ piscreen2_pins: piscreen2_pins { ++ brcm,pins = <17 25 24 22>; ++ brcm,function = <0 1 1 1>; /* in out out out */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ piscreen2: piscreen2@0{ ++ compatible = "ilitek,ili9486"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&piscreen2_pins>; ++ bgr; ++ spi-max-frequency = <64000000>; ++ rotate = <90>; ++ fps = <30>; ++ buswidth = <8>; ++ regwidth = <16>; ++ txbuflen = <32768>; ++ reset-gpios = <&gpio 25 0>; ++ dc-gpios = <&gpio 24 0>; ++ led-gpios = <&gpio 22 1>; ++ debug = <0>; ++ ++ init = <0x10000b0 0x00 ++ 0x1000011 ++ 0x20000ff ++ 0x100003a 0x55 ++ 0x1000036 0x28 ++ 0x10000c0 0x11 0x09 ++ 0x10000c1 0x41 ++ 0x10000c5 0x00 0x00 0x00 0x00 ++ 0x10000b6 0x00 0x02 ++ 0x10000f7 0xa9 0x51 0x2c 0x2 ++ 0x10000be 0x00 0x04 ++ 0x10000e9 0x00 ++ 0x1000011 ++ 0x1000029>; ++ ++ }; ++ ++ piscreen2_ts: piscreen2-ts@1 { ++ compatible = "ti,ads7846"; ++ reg = <1>; ++ ++ spi-max-frequency = <2000000>; ++ interrupts = <17 2>; /* high-to-low edge triggered */ ++ interrupt-parent = <&gpio>; ++ pendown-gpio = <&gpio 17 0>; ++ ti,swap-xy; ++ ti,x-plate-ohms = /bits/ 16 <100>; ++ ti,pressure-max = /bits/ 16 <255>; ++ }; ++ }; ++ }; ++ __overrides__ { ++ speed = <&piscreen2>,"spi-max-frequency:0"; ++ rotate = <&piscreen2>,"rotate:0"; ++ fps = <&piscreen2>,"fps:0"; ++ debug = <&piscreen2>,"debug:0"; ++ xohms = <&piscreen2_ts>,"ti,x-plate-ohms;0"; ++ }; ++}; ++ +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/pisound-overlay.dts +@@ -0,0 +1,114 @@ ++/* ++ * pisound Linux kernel module. ++ * Copyright (C) 2016 Vilniaus Blokas UAB, http://blokas.io/pisound ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * as published by the Free Software Foundation; version 2 of the ++ * License. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * You should have received a copy of the GNU General Public License ++ * along with this program; if not, write to the Free Software ++ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA. ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++#include ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "blokaslabs,pisound"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ ++ pinctrl-0 = <&pisound_button_pins>; ++ ++ osr-gpios = ++ <&gpio 13 GPIO_ACTIVE_HIGH>, ++ <&gpio 26 GPIO_ACTIVE_HIGH>, ++ <&gpio 16 GPIO_ACTIVE_HIGH>; ++ ++ reset-gpios = ++ <&gpio 12 GPIO_ACTIVE_HIGH>, ++ <&gpio 24 GPIO_ACTIVE_HIGH>; ++ ++ data_available-gpios = <&gpio 25 GPIO_ACTIVE_HIGH>; ++ ++ button-gpios = <&gpio 17 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pisound_button_pins>; ++ ++ pisound_button_pins: pisound_button_pins { ++ brcm,pins = <17>; ++ brcm,function = <0>; // Input ++ brcm,pull = <2>; // Pull-Up ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@3 { ++ target-path = "/"; ++ __overlay__ { ++ pcm5102a-codec { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5102a"; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ ++ spidev@0{ ++ status = "disabled"; ++ }; ++ ++ spidev@1{ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@5 { ++ target = <&spi0>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ pisound_spi: pisound_spi@0{ ++ compatible = "blokaslabs,pisound-spi"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi0_pins>; ++ spi-max-frequency = <1000000>; ++ }; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/pitft22-overlay.dts +@@ -0,0 +1,69 @@ ++/* ++ * Device Tree overlay for pitft by Adafruit ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ ++ spidev@0{ ++ status = "disabled"; ++ }; ++ ++ spidev@1{ ++ status = "disabled"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ pitft_pins: pitft_pins { ++ brcm,pins = <25>; ++ brcm,function = <1>; /* out */ ++ brcm,pull = <0>; /* none */ ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ pitft: pitft@0{ ++ compatible = "ilitek,ili9340"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pitft_pins>; ++ ++ spi-max-frequency = <32000000>; ++ rotate = <90>; ++ fps = <25>; ++ bgr; ++ buswidth = <8>; ++ dc-gpios = <&gpio 25 0>; ++ debug = <0>; ++ }; ++ ++ }; ++ }; ++ ++ __overrides__ { ++ speed = <&pitft>,"spi-max-frequency:0"; ++ rotate = <&pitft>,"rotate:0"; ++ fps = <&pitft>,"fps:0"; ++ debug = <&pitft>,"debug:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/pitft28-capacitive-overlay.dts +@@ -0,0 +1,91 @@ ++/* ++ * Device Tree overlay for Adafruit PiTFT 2.8" capacitive touch screen ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&gpio>; ++ __overlay__ { ++ pitft_pins: pitft_pins { ++ brcm,pins = <24 25>; ++ brcm,function = <0 1>; /* in out */ ++ brcm,pull = <2 0>; /* pullup none */ ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ pitft: pitft@0{ ++ compatible = "ilitek,ili9340"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pitft_pins>; ++ ++ spi-max-frequency = <32000000>; ++ rotate = <90>; ++ fps = <25>; ++ bgr; ++ buswidth = <8>; ++ dc-gpios = <&gpio 25 0>; ++ debug = <0>; ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&i2c1>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ ft6236: ft6236@38 { ++ compatible = "focaltech,ft6236"; ++ reg = <0x38>; ++ ++ interrupt-parent = <&gpio>; ++ interrupts = <24 2>; ++ touchscreen-size-x = <240>; ++ touchscreen-size-y = <320>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ speed = <&pitft>,"spi-max-frequency:0"; ++ rotate = <&pitft>,"rotate:0"; ++ fps = <&pitft>,"fps:0"; ++ debug = <&pitft>,"debug:0"; ++ touch-sizex = <&ft6236>,"touchscreen-size-x?"; ++ touch-sizey = <&ft6236>,"touchscreen-size-y?"; ++ touch-invx = <&ft6236>,"touchscreen-inverted-x?"; ++ touch-invy = <&ft6236>,"touchscreen-inverted-y?"; ++ touch-swapxy = <&ft6236>,"touchscreen-swapped-x-y?"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/pitft28-resistive-overlay.dts +@@ -0,0 +1,121 @@ ++/* ++ * Device Tree overlay for Adafruit PiTFT 2.8" resistive touch screen ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ pitft_pins: pitft_pins { ++ brcm,pins = <24 25>; ++ brcm,function = <0 1>; /* in out */ ++ brcm,pull = <2 0>; /* pullup none */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ pitft: pitft@0{ ++ compatible = "ilitek,ili9340"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pitft_pins>; ++ ++ spi-max-frequency = <32000000>; ++ rotate = <90>; ++ fps = <25>; ++ bgr; ++ buswidth = <8>; ++ dc-gpios = <&gpio 25 0>; ++ debug = <0>; ++ }; ++ ++ pitft_ts@1 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ compatible = "st,stmpe610"; ++ reg = <1>; ++ ++ spi-max-frequency = <500000>; ++ irq-gpio = <&gpio 24 0x2>; /* IRQF_TRIGGER_FALLING */ ++ interrupts = <24 2>; /* high-to-low edge triggered */ ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ ++ stmpe_touchscreen { ++ compatible = "st,stmpe-ts"; ++ st,sample-time = <4>; ++ st,mod-12b = <1>; ++ st,ref-sel = <0>; ++ st,adc-freq = <2>; ++ st,ave-ctrl = <3>; ++ st,touch-det-delay = <4>; ++ st,settling = <2>; ++ st,fraction-z = <7>; ++ st,i-drive = <0>; ++ }; ++ ++ stmpe_gpio: stmpe_gpio { ++ #gpio-cells = <2>; ++ compatible = "st,stmpe-gpio"; ++ /* ++ * only GPIO2 is wired/available ++ * and it is wired to the backlight ++ */ ++ st,norequest-mask = <0x7b>; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@5 { ++ target-path = "/soc"; ++ __overlay__ { ++ backlight { ++ compatible = "gpio-backlight"; ++ gpios = <&stmpe_gpio 2 0>; ++ default-on; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ speed = <&pitft>,"spi-max-frequency:0"; ++ rotate = <&pitft>,"rotate:0"; ++ fps = <&pitft>,"fps:0"; ++ debug = <&pitft>,"debug:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/pitft35-resistive-overlay.dts +@@ -0,0 +1,121 @@ ++/* ++ * Device Tree overlay for Adafruit PiTFT 3.5" resistive touch screen ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ pitft_pins: pitft_pins { ++ brcm,pins = <24 25>; ++ brcm,function = <0 1>; /* in out */ ++ brcm,pull = <2 0>; /* pullup none */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ pitft: pitft@0{ ++ compatible = "himax,hx8357d"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pitft_pins>; ++ ++ spi-max-frequency = <32000000>; ++ rotate = <90>; ++ fps = <25>; ++ bgr; ++ buswidth = <8>; ++ dc-gpios = <&gpio 25 0>; ++ debug = <0>; ++ }; ++ ++ pitft_ts@1 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ compatible = "st,stmpe610"; ++ reg = <1>; ++ ++ spi-max-frequency = <500000>; ++ irq-gpio = <&gpio 24 0x2>; /* IRQF_TRIGGER_FALLING */ ++ interrupts = <24 2>; /* high-to-low edge triggered */ ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ ++ stmpe_touchscreen { ++ compatible = "st,stmpe-ts"; ++ st,sample-time = <4>; ++ st,mod-12b = <1>; ++ st,ref-sel = <0>; ++ st,adc-freq = <2>; ++ st,ave-ctrl = <3>; ++ st,touch-det-delay = <4>; ++ st,settling = <2>; ++ st,fraction-z = <7>; ++ st,i-drive = <0>; ++ }; ++ ++ stmpe_gpio: stmpe_gpio { ++ #gpio-cells = <2>; ++ compatible = "st,stmpe-gpio"; ++ /* ++ * only GPIO2 is wired/available ++ * and it is wired to the backlight ++ */ ++ st,norequest-mask = <0x7b>; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@5 { ++ target-path = "/soc"; ++ __overlay__ { ++ backlight { ++ compatible = "gpio-backlight"; ++ gpios = <&stmpe_gpio 2 0>; ++ default-on; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ speed = <&pitft>,"spi-max-frequency:0"; ++ rotate = <&pitft>,"rotate:0"; ++ fps = <&pitft>,"fps:0"; ++ debug = <&pitft>,"debug:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/pps-gpio-overlay.dts +@@ -0,0 +1,35 @@ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ pps: pps { ++ compatible = "pps-gpio"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pps_pins>; ++ gpios = <&gpio 18 0>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ pps_pins: pps_pins { ++ brcm,pins = <18>; ++ brcm,function = <0>; // in ++ brcm,pull = <0>; // off ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ gpiopin = <&pps>,"gpios:4", ++ <&pps_pins>,"brcm,pins:0"; ++ assert_falling_edge = <&pps>,"assert-falling-edge?"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/pwm-2chan-overlay.dts +@@ -0,0 +1,47 @@ ++/dts-v1/; ++/plugin/; ++ ++/* ++This is the 2-channel overlay - only use it if you need both channels. ++ ++Legal pin,function combinations for each channel: ++ PWM0: 12,4(Alt0) 18,2(Alt5) 40,4(Alt0) 52,5(Alt1) ++ PWM1: 13,4(Alt0) 19,2(Alt5) 41,4(Alt0) 45,4(Alt0) 53,5(Alt1) ++ ++N.B.: ++ 1) Pin 18 is the only one available on all platforms, and ++ it is the one used by the I2S audio interface. ++ Pins 12 and 13 might be better choices on an A+, B+ or Pi2. ++ 2) The onboard analogue audio output uses both PWM channels. ++ 3) So be careful mixing audio and PWM. ++*/ ++ ++/ { ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ pwm_pins: pwm_pins { ++ brcm,pins = <18 19>; ++ brcm,function = <2 2>; /* Alt5 */ ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&pwm>; ++ frag1: __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pwm_pins>; ++ assigned-clock-rates = <100000000>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ pin = <&pwm_pins>,"brcm,pins:0"; ++ pin2 = <&pwm_pins>,"brcm,pins:4"; ++ func = <&pwm_pins>,"brcm,function:0"; ++ func2 = <&pwm_pins>,"brcm,function:4"; ++ clock = <&frag1>,"assigned-clock-rates:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/pwm-overlay.dts +@@ -0,0 +1,43 @@ ++/dts-v1/; ++/plugin/; ++ ++/* ++Legal pin,function combinations for each channel: ++ PWM0: 12,4(Alt0) 18,2(Alt5) 40,4(Alt0) 52,5(Alt1) ++ PWM1: 13,4(Alt0) 19,2(Alt5) 41,4(Alt0) 45,4(Alt0) 53,5(Alt1) ++ ++N.B.: ++ 1) Pin 18 is the only one available on all platforms, and ++ it is the one used by the I2S audio interface. ++ Pins 12 and 13 might be better choices on an A+, B+ or Pi2. ++ 2) The onboard analogue audio output uses both PWM channels. ++ 3) So be careful mixing audio and PWM. ++*/ ++ ++/ { ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ pwm_pins: pwm_pins { ++ brcm,pins = <18>; ++ brcm,function = <2>; /* Alt5 */ ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&pwm>; ++ frag1: __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pwm_pins>; ++ assigned-clock-rates = <100000000>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ pin = <&pwm_pins>,"brcm,pins:0"; ++ func = <&pwm_pins>,"brcm,function:0"; ++ clock = <&frag1>,"assigned-clock-rates:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/qca7000-overlay.dts +@@ -0,0 +1,52 @@ ++// Overlay for the Qualcomm Atheros QCA7000 on I2SE's PLC Stamp micro EVK ++// Visit: https://www.i2se.com/product/plc-stamp-micro-evk for details ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "okay"; ++ ++ spidev@0 { ++ status = "disabled"; ++ }; ++ ++ eth1: qca7000@0 { ++ compatible = "qca,qca7000"; ++ reg = <0>; /* CE0 */ ++ pinctrl-names = "default"; ++ pinctrl-0 = <ð1_pins>; ++ interrupt-parent = <&gpio>; ++ interrupts = <23 0x1>; /* rising edge */ ++ spi-max-frequency = <12000000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ eth1_pins: eth1_pins { ++ brcm,pins = <23>; ++ brcm,function = <0>; /* in */ ++ brcm,pull = <0>; /* none */ ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ int_pin = <ð1>, "interrupts:0", ++ <ð1_pins>, "brcm,pins:0"; ++ speed = <ð1>, "spi-max-frequency:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/raspidac3-overlay.dts +@@ -0,0 +1,45 @@ ++// Definitions for RaspiDACv3 ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcm5122@4c { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5122"; ++ reg = <0x4c>; ++ status = "okay"; ++ }; ++ ++ tpa6130a2: tpa6130a2@60 { ++ compatible = "ti,tpa6130a2"; ++ reg = <0x60>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "jg,raspidacv3"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/rpi-backlight-overlay.dts +@@ -0,0 +1,21 @@ ++/* ++ * Devicetree overlay for mailbox-driven Raspberry Pi DSI Display ++ * backlight controller ++ */ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ rpi_backlight: rpi_backlight { ++ compatible = "raspberrypi,rpi-backlight"; ++ firmware = <&firmware>; ++ status = "okay"; ++ }; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/rpi-dac-overlay.dts +@@ -0,0 +1,34 @@ ++// Definitions for RPi DAC ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/"; ++ __overlay__ { ++ pcm1794a-codec { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm1794a"; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "rpi,rpi-dac"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/rpi-display-overlay.dts +@@ -0,0 +1,89 @@ ++/* ++ * Device Tree overlay for rpi-display by Watterott ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ rpi_display_pins: rpi_display_pins { ++ brcm,pins = <18 23 24 25>; ++ brcm,function = <1 1 1 0>; /* out out out in */ ++ brcm,pull = <0 0 0 2>; /* - - - up */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ rpidisplay: rpi-display@0{ ++ compatible = "ilitek,ili9341"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&rpi_display_pins>; ++ ++ spi-max-frequency = <32000000>; ++ rotate = <270>; ++ bgr; ++ fps = <30>; ++ buswidth = <8>; ++ reset-gpios = <&gpio 23 0>; ++ dc-gpios = <&gpio 24 0>; ++ led-gpios = <&gpio 18 1>; ++ debug = <0>; ++ }; ++ ++ rpidisplay_ts: rpi-display-ts@1 { ++ compatible = "ti,ads7846"; ++ reg = <1>; ++ ++ spi-max-frequency = <2000000>; ++ interrupts = <25 2>; /* high-to-low edge triggered */ ++ interrupt-parent = <&gpio>; ++ pendown-gpio = <&gpio 25 0>; ++ ti,x-plate-ohms = /bits/ 16 <60>; ++ ti,pressure-max = /bits/ 16 <255>; ++ }; ++ }; ++ }; ++ __overrides__ { ++ speed = <&rpidisplay>,"spi-max-frequency:0"; ++ rotate = <&rpidisplay>,"rotate:0"; ++ fps = <&rpidisplay>,"fps:0"; ++ debug = <&rpidisplay>,"debug:0"; ++ xohms = <&rpidisplay_ts>,"ti,x-plate-ohms;0"; ++ swapxy = <&rpidisplay_ts>,"ti,swap-xy?"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/rpi-ft5406-overlay.dts +@@ -0,0 +1,17 @@ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ rpi_ft5406: rpi_ft5406 { ++ compatible = "rpi,rpi-ft5406"; ++ firmware = <&firmware>; ++ status = "okay"; ++ }; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/rpi-proto-overlay.dts +@@ -0,0 +1,39 @@ ++// Definitions for Rpi-Proto ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ wm8731@1a { ++ #sound-dai-cells = <0>; ++ compatible = "wlf,wm8731"; ++ reg = <0x1a>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "rpi,rpi-proto"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/rpi-sense-overlay.dts +@@ -0,0 +1,47 @@ ++// rpi-sense HAT ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ rpi-sense@46 { ++ compatible = "rpi,rpi-sense"; ++ reg = <0x46>; ++ keys-int-gpios = <&gpio 23 1>; ++ status = "okay"; ++ }; ++ ++ lsm9ds1-magn@1c { ++ compatible = "st,lsm9ds1-magn"; ++ reg = <0x1c>; ++ status = "okay"; ++ }; ++ ++ lsm9ds1-accel6a { ++ compatible = "st,lsm9ds1-accel"; ++ reg = <0x6a>; ++ status = "okay"; ++ }; ++ ++ lps25h-press@5c { ++ compatible = "st,lps25h-press"; ++ reg = <0x5c>; ++ status = "okay"; ++ }; ++ ++ hts221-humid@5f { ++ compatible = "st,hts221-humid"; ++ reg = <0x5f>; ++ status = "okay"; ++ }; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/rra-digidac1-wm8741-audio-overlay.dts +@@ -0,0 +1,81 @@ ++// Definitions for RRA DigiDAC1 Audio card ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ aliases { ++ ldo0 = &ldo0; ++ ldo1 = &ldo1; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/soc"; ++ __overlay__ { ++ ++ ldo1: ldo1 { ++ compatible = "regulator-fixed"; ++ regulator-name = "DC_5V"; ++ regulator-min-microvolt = <5000000>; ++ regulator-max-microvolt = <5000000>; ++ regulator-always-on; ++ }; ++ ++ ldo0: ldo0 { ++ compatible = "regulator-fixed"; ++ regulator-name = "DC_3V3"; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ regulator-always-on; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ wm8804@3b { ++ #sound-dai-cells = <0>; ++ compatible = "wlf,wm8804"; ++ reg = <0x3b>; ++ status = "okay"; ++ PVDD-supply = <&ldo0>; ++ DVDD-supply = <&ldo0>; ++ }; ++ ++ wm8742: wm8741@1a { ++ compatible = "wlf,wm8741"; ++ reg = <0x1a>; ++ status = "okay"; ++ AVDD-supply = <&ldo1>; ++ DVDD-supply = <&ldo0>; ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "rra,digidac1-soundcard"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/sc16is750-i2c-overlay.dts +@@ -0,0 +1,37 @@ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&i2c_arm>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ sc16is750: sc16is750@48 { ++ compatible = "nxp,sc16is750"; ++ reg = <0x48>; /* address */ ++ clocks = <&sc16is750_clk>; ++ interrupt-parent = <&gpio>; ++ interrupts = <24 2>; /* IRQ_TYPE_EDGE_FALLING */ ++ #gpio-cells = <2>; ++ ++ sc16is750_clk: sc16is750_clk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <14745600>; ++ }; ++ }; ++ }; ++ }; ++ ++ ++ __overrides__ { ++ int_pin = <&sc16is750>,"interrupts:0"; ++ addr = <&sc16is750>,"reg:0"; ++ }; ++ ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/sc16is752-spi1-overlay.dts +@@ -0,0 +1,61 @@ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ spi1_pins: spi1_pins { ++ brcm,pins = <19 20 21>; ++ brcm,function = <3>; /* alt4 */ ++ }; ++ ++ spi1_cs_pins: spi1_cs_pins { ++ brcm,pins = <18>; ++ brcm,function = <1>; /* output */ ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi1>; ++ frag1: __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi1_pins &spi1_cs_pins>; ++ cs-gpios = <&gpio 18 1>; ++ status = "okay"; ++ ++ sc16is752: sc16is752@0 { ++ compatible = "nxp,sc16is752"; ++ reg = <0>; /* CE0 */ ++ clocks = <&sc16is752_clk>; ++ interrupt-parent = <&gpio>; ++ interrupts = <24 2>; /* IRQ_TYPE_EDGE_FALLING */ ++ #gpio-controller; ++ #gpio-cells = <2>; ++ spi-max-frequency = <4000000>; ++ ++ sc16is752_clk: sc16is752_clk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <14745600>; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&aux>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ int_pin = <&sc16is752>,"interrupts:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/sdhost-overlay.dts +@@ -0,0 +1,32 @@ ++/dts-v1/; ++/plugin/; ++ ++/* Provide backwards compatible aliases for the old sdhost dtparams. */ ++ ++/{ ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&sdhost>; ++ frag0: __overlay__ { ++ brcm,overclock-50 = <0>; ++ brcm,pio-limit = <1>; ++ brcm,debug-flags = <0>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&mmc>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ __overrides__ { ++ overclock_50 = <&frag0>,"brcm,overclock-50:0"; ++ force_pio = <&frag0>,"brcm,force-pio?"; ++ pio_limit = <&frag0>,"brcm,pio-limit:0"; ++ debug = <&frag0>,"brcm,debug?"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/sdio-1bit-overlay.dts +@@ -0,0 +1,36 @@ ++/* Enable 1-bit SDIO from MMC interface via GPIOs 22-25. Includes sdhost overlay. */ ++ ++/include/ "sdhost-overlay.dts" ++ ++/{ ++ compatible = "brcm,bcm2708"; ++ ++ fragment@3 { ++ target = <&mmc>; ++ sdio_mmc: __overlay__ { ++ compatible = "brcm,bcm2835-mmc"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sdio_pins>; ++ non-removable; ++ bus-width = <1>; ++ brcm,overclock-50 = <0>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&gpio>; ++ __overlay__ { ++ sdio_pins: sdio_pins { ++ brcm,pins = <22 23 24 25>; ++ brcm,function = <7 7 7 7>; /* ALT3 = SD1 */ ++ brcm,pull = <0 2 2 2>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ poll_once = <&sdio_mmc>,"non-removable?"; ++ sdio_overclock = <&sdio_mmc>,"brcm,overclock-50:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/sdio-overlay.dts +@@ -0,0 +1,36 @@ ++/* Enable SDIO from MMC interface via GPIOs 22-27. Includes sdhost overlay. */ ++ ++/include/ "sdhost-overlay.dts" ++ ++/{ ++ compatible = "brcm,bcm2708"; ++ ++ fragment@3 { ++ target = <&mmc>; ++ sdio_mmc: __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sdio_pins>; ++ non-removable; ++ bus-width = <4>; ++ brcm,overclock-50 = <0>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&gpio>; ++ __overlay__ { ++ sdio_pins: sdio_pins { ++ brcm,pins = <22 23 24 25 26 27>; ++ brcm,function = <7 7 7 7 7 7>; /* ALT3 = SD1 */ ++ brcm,pull = <0 2 2 2 2 2>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ poll_once = <&sdio_mmc>,"non-removable?"; ++ bus_width = <&sdio_mmc>,"bus-width:0"; ++ sdio_overclock = <&sdio_mmc>,"brcm,overclock-50:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/sdtweak-overlay.dts +@@ -0,0 +1,23 @@ ++/dts-v1/; ++/plugin/; ++ ++/* Provide backwards compatible aliases for the old sdhost dtparams. */ ++ ++/{ ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&sdhost>; ++ frag0: __overlay__ { ++ brcm,overclock-50 = <0>; ++ brcm,pio-limit = <1>; ++ }; ++ }; ++ ++ __overrides__ { ++ overclock_50 = <&frag0>,"brcm,overclock-50:0"; ++ force_pio = <&frag0>,"brcm,force-pio?"; ++ pio_limit = <&frag0>,"brcm,pio-limit:0"; ++ debug = <&frag0>,"brcm,debug?"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/smi-dev-overlay.dts +@@ -0,0 +1,18 @@ ++// Description: Overlay to enable character device interface for SMI. ++// Author: Luke Wren ++ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ fragment@0 { ++ target = <&soc>; ++ __overlay__ { ++ smi_dev { ++ compatible = "brcm,bcm2835-smi-dev"; ++ smi_handle = <&smi>; ++ status = "okay"; ++ }; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/smi-nand-overlay.dts +@@ -0,0 +1,69 @@ ++// Description: Overlay to enable NAND flash through ++// the secondary memory interface ++// Author: Luke Wren ++ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&smi>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&smi_pins>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&soc>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <1>; ++ ++ nand: flash@0 { ++ compatible = "brcm,bcm2835-smi-nand"; ++ smi_handle = <&smi>; ++ #address-cells = <1>; ++ #size-cells = <1>; ++ status = "okay"; ++ ++ partition@0 { ++ label = "stage2"; ++ // 128k ++ reg = <0 0x20000>; ++ read-only; ++ }; ++ partition@1 { ++ label = "firmware"; ++ // 16M ++ reg = <0x20000 0x1000000>; ++ read-only; ++ }; ++ partition@2 { ++ label = "root"; ++ // 2G (will need to use 64 bit for >=4G) ++ reg = <0x1020000 0x80000000>; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&gpio>; ++ __overlay__ { ++ smi_pins: smi_pins { ++ brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11 ++ 12 13 14 15>; ++ /* Alt 1: SMI */ ++ brcm,function = <5 5 5 5 5 5 5 5 5 5 5 ++ 5 5 5 5 5>; ++ /* /CS, /WE and /OE are pulled high, as they are ++ generally active low signals */ ++ brcm,pull = <2 2 2 2 2 2 2 2 0 0 0 0 0 0 0 0>; ++ }; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/smi-overlay.dts +@@ -0,0 +1,37 @@ ++// Description: Overlay to enable the secondary memory interface peripheral ++// Author: Luke Wren ++ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&smi>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&smi_pins>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ smi_pins: smi_pins { ++ /* Don't configure the top two address bits, as ++ these are already used as ID_SD and ID_SC */ ++ brcm,pins = <2 3 4 5 6 7 8 9 10 11 12 13 14 15 ++ 16 17 18 19 20 21 22 23 24 25>; ++ /* Alt 0: SMI */ ++ brcm,function = <5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 ++ 5 5 5 5 5 5 5 5 5>; ++ /* /CS, /WE and /OE are pulled high, as they are ++ generally active low signals */ ++ brcm,pull = <2 2 2 2 2 2 0 0 0 0 0 0 0 0 0 0 0 ++ 0 0 0 0 0 0 0>; ++ }; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi-gpio35-39-overlay.dts +@@ -0,0 +1,31 @@ ++/* ++ * Device tree overlay to move spi0 to gpio 35 to 39 on CM ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ cs-gpios = <&gpio 36 1>, <&gpio 35 1>; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi0_cs_pins>; ++ __overlay__ { ++ brcm,pins = <36 35>; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spi0_pins>; ++ __overlay__ { ++ brcm,pins = <37 38 39>; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi-rtc-overlay.dts +@@ -0,0 +1,33 @@ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&spidev0>; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ rtc-pcf2123@0 { ++ compatible = "nxp,rtc-pcf2123"; ++ spi-max-frequency = <5000000>; ++ spi-cs-high = <1>; ++ reg = <0>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ pcf2123 = <0>, "=0=1"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi0-hw-cs-overlay.dts +@@ -0,0 +1,26 @@ ++/* ++ * Device tree overlay to re-enable hardware CS for SPI0 ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ cs-gpios = <0>, <0>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi0_cs_pins>; ++ __overlay__ { ++ brcm,pins = <8 7>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi1-1cs-overlay.dts +@@ -0,0 +1,57 @@ ++/dts-v1/; ++/plugin/; ++ ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ spi1_pins: spi1_pins { ++ brcm,pins = <19 20 21>; ++ brcm,function = <3>; /* alt4 */ ++ }; ++ ++ spi1_cs_pins: spi1_cs_pins { ++ brcm,pins = <18>; ++ brcm,function = <1>; /* output */ ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi1>; ++ frag1: __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi1_pins &spi1_cs_pins>; ++ cs-gpios = <&gpio 18 1>; ++ status = "okay"; ++ ++ spidev1_0: spidev@0 { ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&aux>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ cs0_pin = <&spi1_cs_pins>,"brcm,pins:0", ++ <&frag1>,"cs-gpios:4"; ++ cs0_spidev = <&spidev1_0>,"status"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi1-2cs-overlay.dts +@@ -0,0 +1,69 @@ ++/dts-v1/; ++/plugin/; ++ ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ spi1_pins: spi1_pins { ++ brcm,pins = <19 20 21>; ++ brcm,function = <3>; /* alt4 */ ++ }; ++ ++ spi1_cs_pins: spi1_cs_pins { ++ brcm,pins = <18 17>; ++ brcm,function = <1>; /* output */ ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi1>; ++ frag1: __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi1_pins &spi1_cs_pins>; ++ cs-gpios = <&gpio 18 1>, <&gpio 17 1>; ++ status = "okay"; ++ ++ spidev1_0: spidev@0 { ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ }; ++ ++ spidev1_1: spidev@1 { ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&aux>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ cs0_pin = <&spi1_cs_pins>,"brcm,pins:0", ++ <&frag1>,"cs-gpios:4"; ++ cs1_pin = <&spi1_cs_pins>,"brcm,pins:4", ++ <&frag1>,"cs-gpios:16"; ++ cs0_spidev = <&spidev1_0>,"status"; ++ cs1_spidev = <&spidev1_1>,"status"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi1-3cs-overlay.dts +@@ -0,0 +1,81 @@ ++/dts-v1/; ++/plugin/; ++ ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ spi1_pins: spi1_pins { ++ brcm,pins = <19 20 21>; ++ brcm,function = <3>; /* alt4 */ ++ }; ++ ++ spi1_cs_pins: spi1_cs_pins { ++ brcm,pins = <18 17 16>; ++ brcm,function = <1>; /* output */ ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi1>; ++ frag1: __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi1_pins &spi1_cs_pins>; ++ cs-gpios = <&gpio 18 1>, <&gpio 17 1>, <&gpio 16 1>; ++ status = "okay"; ++ ++ spidev1_0: spidev@0 { ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ }; ++ ++ spidev1_1: spidev@1 { ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ }; ++ ++ spidev1_2: spidev@2 { ++ compatible = "spidev"; ++ reg = <2>; /* CE2 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&aux>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ cs0_pin = <&spi1_cs_pins>,"brcm,pins:0", ++ <&frag1>,"cs-gpios:4"; ++ cs1_pin = <&spi1_cs_pins>,"brcm,pins:4", ++ <&frag1>,"cs-gpios:16"; ++ cs2_pin = <&spi1_cs_pins>,"brcm,pins:8", ++ <&frag1>,"cs-gpios:28"; ++ cs0_spidev = <&spidev1_0>,"status"; ++ cs1_spidev = <&spidev1_1>,"status"; ++ cs2_spidev = <&spidev1_2>,"status"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi2-1cs-overlay.dts +@@ -0,0 +1,57 @@ ++/dts-v1/; ++/plugin/; ++ ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ spi2_pins: spi2_pins { ++ brcm,pins = <40 41 42>; ++ brcm,function = <3>; /* alt4 */ ++ }; ++ ++ spi2_cs_pins: spi2_cs_pins { ++ brcm,pins = <43>; ++ brcm,function = <1>; /* output */ ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi2>; ++ frag1: __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi2_pins &spi2_cs_pins>; ++ cs-gpios = <&gpio 43 1>; ++ status = "okay"; ++ ++ spidev2_0: spidev@0 { ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&aux>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ cs0_pin = <&spi2_cs_pins>,"brcm,pins:0", ++ <&frag1>,"cs-gpios:4"; ++ cs0_spidev = <&spidev2_0>,"status"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi2-2cs-overlay.dts +@@ -0,0 +1,69 @@ ++/dts-v1/; ++/plugin/; ++ ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ spi2_pins: spi2_pins { ++ brcm,pins = <40 41 42>; ++ brcm,function = <3>; /* alt4 */ ++ }; ++ ++ spi2_cs_pins: spi2_cs_pins { ++ brcm,pins = <43 44>; ++ brcm,function = <1>; /* output */ ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi2>; ++ frag1: __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi2_pins &spi2_cs_pins>; ++ cs-gpios = <&gpio 43 1>, <&gpio 44 1>; ++ status = "okay"; ++ ++ spidev2_0: spidev@0 { ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ }; ++ ++ spidev2_1: spidev@1 { ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&aux>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ cs0_pin = <&spi2_cs_pins>,"brcm,pins:0", ++ <&frag1>,"cs-gpios:4"; ++ cs1_pin = <&spi2_cs_pins>,"brcm,pins:4", ++ <&frag1>,"cs-gpios:16"; ++ cs0_spidev = <&spidev2_0>,"status"; ++ cs1_spidev = <&spidev2_1>,"status"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi2-3cs-overlay.dts +@@ -0,0 +1,81 @@ ++/dts-v1/; ++/plugin/; ++ ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ spi2_pins: spi2_pins { ++ brcm,pins = <40 41 42>; ++ brcm,function = <3>; /* alt4 */ ++ }; ++ ++ spi2_cs_pins: spi2_cs_pins { ++ brcm,pins = <43 44 45>; ++ brcm,function = <1>; /* output */ ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi2>; ++ frag1: __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi2_pins &spi2_cs_pins>; ++ cs-gpios = <&gpio 43 1>, <&gpio 44 1>, <&gpio 45 1>; ++ status = "okay"; ++ ++ spidev2_0: spidev@0 { ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ }; ++ ++ spidev2_1: spidev@1 { ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ }; ++ ++ spidev2_2: spidev@2 { ++ compatible = "spidev"; ++ reg = <2>; /* CE2 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&aux>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ cs0_pin = <&spi2_cs_pins>,"brcm,pins:0", ++ <&frag1>,"cs-gpios:4"; ++ cs1_pin = <&spi2_cs_pins>,"brcm,pins:4", ++ <&frag1>,"cs-gpios:16"; ++ cs2_pin = <&spi2_cs_pins>,"brcm,pins:8", ++ <&frag1>,"cs-gpios:28"; ++ cs0_spidev = <&spidev2_0>,"status"; ++ cs1_spidev = <&spidev2_1>,"status"; ++ cs2_spidev = <&spidev2_2>,"status"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/tinylcd35-overlay.dts +@@ -0,0 +1,224 @@ ++/* ++ * tinylcd35-overlay.dts ++ * ++ * ------------------------------------------------- ++ * www.tinlylcd.com ++ * ------------------------------------------------- ++ * Device---Driver-----BUS GPIO's ++ * display tinylcd35 spi0.0 25 24 18 ++ * touch ads7846 spi0.1 5 ++ * rtc ds1307 i2c1-0068 ++ * rtc pcf8563 i2c1-0051 ++ * keypad gpio-keys --------- 17 22 27 23 28 ++ * ++ * ++ * TinyLCD.com 3.5 inch TFT ++ * ++ * Version 001 ++ * 5/3/2015 -- Noralf Trønnes Initial Device tree framework ++ * 10/3/2015 -- tinylcd@gmail.com added ds1307 support. ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ tinylcd35_pins: tinylcd35_pins { ++ brcm,pins = <25 24 18>; ++ brcm,function = <1>; /* out */ ++ }; ++ tinylcd35_ts_pins: tinylcd35_ts_pins { ++ brcm,pins = <5>; ++ brcm,function = <0>; /* in */ ++ }; ++ keypad_pins: keypad_pins { ++ brcm,pins = <4 17 22 23 27>; ++ brcm,function = <0>; /* in */ ++ brcm,pull = <1>; /* down */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ tinylcd35: tinylcd35@0{ ++ compatible = "neosec,tinylcd"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&tinylcd35_pins>, ++ <&tinylcd35_ts_pins>; ++ ++ spi-max-frequency = <48000000>; ++ rotate = <270>; ++ fps = <20>; ++ bgr; ++ buswidth = <8>; ++ reset-gpios = <&gpio 25 0>; ++ dc-gpios = <&gpio 24 0>; ++ led-gpios = <&gpio 18 1>; ++ debug = <0>; ++ ++ init = <0x10000B0 0x80 ++ 0x10000C0 0x0A 0x0A ++ 0x10000C1 0x01 0x01 ++ 0x10000C2 0x33 ++ 0x10000C5 0x00 0x42 0x80 ++ 0x10000B1 0xD0 0x11 ++ 0x10000B4 0x02 ++ 0x10000B6 0x00 0x22 0x3B ++ 0x10000B7 0x07 ++ 0x1000036 0x58 ++ 0x10000F0 0x36 0xA5 0xD3 ++ 0x10000E5 0x80 ++ 0x10000E5 0x01 ++ 0x10000B3 0x00 ++ 0x10000E5 0x00 ++ 0x10000F0 0x36 0xA5 0x53 ++ 0x10000E0 0x00 0x35 0x33 0x00 0x00 0x00 0x00 0x35 0x33 0x00 0x00 0x00 ++ 0x100003A 0x55 ++ 0x1000011 ++ 0x2000001 ++ 0x1000029>; ++ }; ++ ++ tinylcd35_ts: tinylcd35_ts@1 { ++ compatible = "ti,ads7846"; ++ reg = <1>; ++ status = "disabled"; ++ ++ spi-max-frequency = <2000000>; ++ interrupts = <5 2>; /* high-to-low edge triggered */ ++ interrupt-parent = <&gpio>; ++ pendown-gpio = <&gpio 5 0>; ++ ti,x-plate-ohms = /bits/ 16 <100>; ++ ti,pressure-max = /bits/ 16 <255>; ++ }; ++ }; ++ }; ++ ++ /* RTC */ ++ ++ fragment@5 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "okay"; ++ ++ pcf8563: pcf8563@51 { ++ compatible = "nxp,pcf8563"; ++ reg = <0x51>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@6 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "okay"; ++ ++ ds1307: ds1307@68 { ++ compatible = "maxim,ds1307"; ++ reg = <0x68>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ /* ++ * Values for input event code is found under the ++ * 'Keys and buttons' heading in include/uapi/linux/input.h ++ */ ++ fragment@7 { ++ target-path = "/soc"; ++ __overlay__ { ++ keypad: keypad { ++ compatible = "gpio-keys"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&keypad_pins>; ++ status = "disabled"; ++ autorepeat; ++ ++ button@17 { ++ label = "GPIO KEY_UP"; ++ linux,code = <103>; ++ gpios = <&gpio 17 0>; ++ }; ++ button@22 { ++ label = "GPIO KEY_DOWN"; ++ linux,code = <108>; ++ gpios = <&gpio 22 0>; ++ }; ++ button@27 { ++ label = "GPIO KEY_LEFT"; ++ linux,code = <105>; ++ gpios = <&gpio 27 0>; ++ }; ++ button@23 { ++ label = "GPIO KEY_RIGHT"; ++ linux,code = <106>; ++ gpios = <&gpio 23 0>; ++ }; ++ button@4 { ++ label = "GPIO KEY_ENTER"; ++ linux,code = <28>; ++ gpios = <&gpio 4 0>; ++ }; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ speed = <&tinylcd35>,"spi-max-frequency:0"; ++ rotate = <&tinylcd35>,"rotate:0"; ++ fps = <&tinylcd35>,"fps:0"; ++ debug = <&tinylcd35>,"debug:0"; ++ touch = <&tinylcd35_ts>,"status"; ++ touchgpio = <&tinylcd35_ts_pins>,"brcm,pins:0", ++ <&tinylcd35_ts>,"interrupts:0", ++ <&tinylcd35_ts>,"pendown-gpio:4"; ++ xohms = <&tinylcd35_ts>,"ti,x-plate-ohms;0"; ++ rtc-pcf = <0>,"=5"; ++ rtc-ds = <0>,"=6"; ++ keypad = <&keypad>,"status"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/uart1-overlay.dts +@@ -0,0 +1,38 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target = <&uart1>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart1_pins>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ uart1_pins: uart1_pins { ++ brcm,pins = <14 15>; ++ brcm,function = <2>; /* alt5 */ ++ brcm,pull = <0 2>; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target-path = "/chosen"; ++ __overlay__ { ++ bootargs = "8250.nr_uarts=1"; ++ }; ++ }; ++ ++ __overrides__ { ++ txd1_pin = <&uart1_pins>,"brcm,pins:0"; ++ rxd1_pin = <&uart1_pins>,"brcm,pins:4"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/vc4-fkms-v3d-overlay.dts +@@ -0,0 +1,89 @@ ++/* ++ * vc4-fkms-v3d-overlay.dts ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target-path = "/chosen"; ++ __overlay__ { ++ bootargs = "cma=256M@256M"; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/chosen"; ++ __dormant__ { ++ bootargs = "cma=192M@256M"; ++ }; ++ }; ++ ++ fragment@2 { ++ target-path = "/chosen"; ++ __dormant__ { ++ bootargs = "cma=128M@128M"; ++ }; ++ }; ++ ++ fragment@3 { ++ target-path = "/chosen"; ++ __dormant__ { ++ bootargs = "cma=96M@128M"; ++ }; ++ }; ++ ++ fragment@4 { ++ target-path = "/chosen"; ++ __dormant__ { ++ bootargs = "cma=64M@64M"; ++ }; ++ }; ++ ++ fragment@5 { ++ target = <&fb>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@6 { ++ target = <&firmwarekms>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@7 { ++ target = <&v3d>; ++ __overlay__ { ++ interrupts = <1 10>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@8 { ++ target = <&gpu>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@9 { ++ target-path = "/soc/dma"; ++ __overlay__ { ++ brcm,dma-channel-mask = <0x7f35>; ++ }; ++ }; ++ ++ __overrides__ { ++ cma-256 = <0>,"+0-1-2-3-4"; ++ cma-192 = <0>,"-0+1-2-3-4"; ++ cma-128 = <0>,"-0-1+2-3-4"; ++ cma-96 = <0>,"-0-1-2+3-4"; ++ cma-64 = <0>,"-0-1-2-3+4"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts +@@ -0,0 +1,136 @@ ++/* ++ * vc4-kms-v3d-overlay.dts ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target-path = "/chosen"; ++ __overlay__ { ++ bootargs = "cma=256M@256M"; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/chosen"; ++ __dormant__ { ++ bootargs = "cma=192M@256M"; ++ }; ++ }; ++ ++ fragment@2 { ++ target-path = "/chosen"; ++ __dormant__ { ++ bootargs = "cma=128M@128M"; ++ }; ++ }; ++ ++ fragment@3 { ++ target-path = "/chosen"; ++ __dormant__ { ++ bootargs = "cma=96M@128M"; ++ }; ++ }; ++ ++ fragment@4 { ++ target-path = "/chosen"; ++ __dormant__ { ++ bootargs = "cma=64M@64M"; ++ }; ++ }; ++ ++ fragment@5 { ++ target = <&i2c2>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@6 { ++ target = <&cprman>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@7 { ++ target = <&fb>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@8 { ++ target = <&pixelvalve0>; ++ __overlay__ { ++ interrupts = <2 13>; /* pwa0 */ ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@9 { ++ target = <&pixelvalve1>; ++ __overlay__ { ++ interrupts = <2 14>; /* pwa1 */ ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@10 { ++ target = <&pixelvalve2>; ++ __overlay__ { ++ interrupts = <2 10>; /* pixelvalve */ ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@11 { ++ target = <&hvs>; ++ __overlay__ { ++ interrupts = <2 1>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@12 { ++ target = <&hdmi>; ++ __overlay__ { ++ interrupts = <2 8>, <2 9>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@13 { ++ target = <&v3d>; ++ __overlay__ { ++ interrupts = <1 10>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@14 { ++ target = <&gpu>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@15 { ++ target-path = "/soc/dma"; ++ __overlay__ { ++ brcm,dma-channel-mask = <0x7f35>; ++ }; ++ }; ++ ++ __overrides__ { ++ cma-256 = <0>,"+0-1-2-3-4"; ++ cma-192 = <0>,"-0+1-2-3-4"; ++ cma-128 = <0>,"-0-1+2-3-4"; ++ cma-96 = <0>,"-0-1-2+3-4"; ++ cma-64 = <0>,"-0-1-2-3+4"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/vga666-overlay.dts +@@ -0,0 +1,30 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2708"; ++ ++ // There is no VGA driver module, but we need a platform device ++ // node (that doesn't already use pinctrl) to hang the pinctrl ++ // reference on - leds will do ++ ++ fragment@0 { ++ target = <&leds>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&vga666_pins>; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ vga666_pins: vga666_pins { ++ brcm,pins = <2 3 4 5 6 7 8 9 10 11 12 ++ 13 14 15 16 17 18 19 20 21>; ++ brcm,function = <6>; /* alt2 */ ++ brcm,pull = <0>; /* no pull */ ++ }; ++ }; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/w1-gpio-overlay.dts +@@ -0,0 +1,39 @@ ++// Definitions for w1-gpio module (without external pullup) ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ ++ w1: onewire@0 { ++ compatible = "w1-gpio"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&w1_pins>; ++ gpios = <&gpio 4 0>; ++ rpi,parasitic-power = <0>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ w1_pins: w1_pins { ++ brcm,pins = <4>; ++ brcm,function = <0>; // in (initially) ++ brcm,pull = <0>; // off ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ gpiopin = <&w1>,"gpios:4", ++ <&w1_pins>,"brcm,pins:0"; ++ pullup = <&w1>,"rpi,parasitic-power:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/w1-gpio-pullup-overlay.dts +@@ -0,0 +1,41 @@ ++// Definitions for w1-gpio module (with external pullup) ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2708"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ ++ w1: onewire@0 { ++ compatible = "w1-gpio"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&w1_pins>; ++ gpios = <&gpio 4 0>, <&gpio 5 1>; ++ rpi,parasitic-power = <0>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ w1_pins: w1_pins { ++ brcm,pins = <4 5>; ++ brcm,function = <0 1>; // in out ++ brcm,pull = <0 0>; // off off ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ gpiopin = <&w1>,"gpios:4", ++ <&w1_pins>,"brcm,pins:0"; ++ extpullup = <&w1>,"gpios:16", ++ <&w1_pins>,"brcm,pins:4"; ++ pullup = <&w1>,"rpi,parasitic-power:0"; ++ }; ++}; +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/wittypi-overlay.dts +@@ -0,0 +1,44 @@ ++/* ++ * Device Tree overlay for Witty Pi extension board by UUGear ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ ++ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; ++ ++ fragment@0 { ++ target = <&leds>; ++ __overlay__ { ++ compatible = "gpio-leds"; ++ wittypi_led: wittypi_led { ++ label = "wittypi_led"; ++ linux,default-trigger = "default-on"; ++ gpios = <&gpio 17 0>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ rtc: ds1337@68 { ++ compatible = "dallas,ds1337"; ++ reg = <0x68>; ++ wakeup-source; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ led_gpio = <&wittypi_led>,"gpios:4"; ++ led_trigger = <&wittypi_led>,"linux,default-trigger"; ++ }; ++ ++}; +--- a/scripts/Makefile.dtbinst ++++ b/scripts/Makefile.dtbinst +@@ -27,6 +27,7 @@ ifeq ("$(dtbinst-root)", "$(obj)") + endif + + dtbinst-files := $(dtb-y) ++dtboinst-files := $(dtbo-y) + dtbinst-dirs := $(dts-dirs) + + # Helper targets for Installing DTBs into the boot directory +@@ -35,15 +36,18 @@ quiet_cmd_dtb_install = INSTALL $< + + install-dir = $(patsubst $(dtbinst-root)%,$(INSTALL_DTBS_PATH)%,$(obj)) + +-$(dtbinst-files) $(dtbinst-dirs): | __dtbs_install_prep ++$(dtbinst-files) $(dtboinst-files) $(dtbinst-dirs): | __dtbs_install_prep + + $(dtbinst-files): %.dtb: $(obj)/%.dtb + $(call cmd,dtb_install,$(install-dir)) + ++$(dtboinst-files): %.dtbo: $(obj)/%.dtbo ++ $(call cmd,dtb_install,$(install-dir)) ++ + $(dtbinst-dirs): + $(Q)$(MAKE) $(dtbinst)=$(obj)/$@ + +-PHONY += $(dtbinst-files) $(dtbinst-dirs) +-__dtbs_install: $(dtbinst-files) $(dtbinst-dirs) ++PHONY += $(dtbinst-files) $(dtboinst-files) $(dtbinst-dirs) ++__dtbs_install: $(dtbinst-files) $(dtboinst-files) $(dtbinst-dirs) + + .PHONY: $(PHONY) +--- a/scripts/Makefile.lib ++++ b/scripts/Makefile.lib +@@ -312,6 +312,17 @@ cmd_dtc = mkdir -p $(dir ${dtc-tmp}) ; \ + $(obj)/%.dtb: $(src)/%.dts FORCE + $(call if_changed_dep,dtc) + ++quiet_cmd_dtco = DTCO $@ ++cmd_dtco = mkdir -p $(dir ${dtc-tmp}) ; \ ++ $(CPP) $(dtc_cpp_flags) -x assembler-with-cpp -o $(dtc-tmp) $< ; \ ++ $(DTC) -@ -H epapr -O dtb -o $@ -b 0 \ ++ -i $(dir $<) $(DTC_FLAGS) \ ++ -d $(depfile).dtc.tmp $(dtc-tmp) ; \ ++ cat $(depfile).pre.tmp $(depfile).dtc.tmp > $(depfile) ++ ++$(obj)/%.dtbo: $(src)/%-overlay.dts FORCE ++ $(call if_changed_dep,dtco) ++ + dtc-tmp = $(subst $(comma),_,$(dot-target).dts.tmp) + + # Bzip2 -- cgit v1.2.3