From c2308a7e4adbb2acc8ff149f91d1ca46801c135e Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?=C3=81lvaro=20Fern=C3=A1ndez=20Rojas?= Date: Mon, 23 Dec 2019 17:25:19 +0100 Subject: brcm2708: update to latest patches from RPi Foundation MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Also removes reverted patches. Signed-off-by: Álvaro Fernández Rojas --- ...ndings-Add-binding-for-the-Sony-IMX219-se.patch | 77 ++++++++++++++++++++++ 1 file changed, 77 insertions(+) create mode 100644 target/linux/brcm2708/patches-4.19/950-0679-media-dt-bindings-Add-binding-for-the-Sony-IMX219-se.patch (limited to 'target/linux/brcm2708/patches-4.19/950-0679-media-dt-bindings-Add-binding-for-the-Sony-IMX219-se.patch') diff --git a/target/linux/brcm2708/patches-4.19/950-0679-media-dt-bindings-Add-binding-for-the-Sony-IMX219-se.patch b/target/linux/brcm2708/patches-4.19/950-0679-media-dt-bindings-Add-binding-for-the-Sony-IMX219-se.patch new file mode 100644 index 0000000000..30fa9b3081 --- /dev/null +++ b/target/linux/brcm2708/patches-4.19/950-0679-media-dt-bindings-Add-binding-for-the-Sony-IMX219-se.patch @@ -0,0 +1,77 @@ +From 2d8a780a994098f7c532b712abd7298e0bca5a12 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 28 Aug 2019 13:34:30 +0100 +Subject: [PATCH] media: dt-bindings: Add binding for the Sony IMX219 + sensor + +The IMX219 is an 8MPix CSI2 sensor, supporting 2 or 4 data lanes. +Document the binding for this device. + +Signed-off-by: Dave Stevenson +--- + .../devicetree/bindings/media/i2c/imx219.txt | 59 +++++++++++++++++++ + 1 file changed, 59 insertions(+) + create mode 100644 Documentation/devicetree/bindings/media/i2c/imx219.txt + +--- /dev/null ++++ b/Documentation/devicetree/bindings/media/i2c/imx219.txt +@@ -0,0 +1,59 @@ ++* Sony 1/4.0-Inch 8Mpixel CMOS Digital Image Sensor ++ ++The Sony imx219 is a 1/4.0-inch CMOS active pixel digital image sensor with ++an active array size of 3280H x 2464V. It is programmable through I2C ++interface. The I2C address is fixed to 0x10 as per sensor data sheet. ++Image data is sent through MIPI CSI-2, which is configured as either 2 or 4 ++data lanes. ++ ++Required Properties: ++- compatible: value should be "sony,imx219" for imx219 sensor ++- reg: I2C bus address of the device ++- clocks: reference to the xclk input clock. ++- clock-names: should be "xclk". ++- DOVDD-supply: Digital I/O voltage supply, 1.8 volts ++- AVDD-supply: Analog voltage supply, 2.8 volts ++- DVDD-supply: Digital core voltage supply, 1.2 volts ++ ++Optional Properties: ++- xclr-gpios: reference to the GPIO connected to the xclr pin, if any. Must be ++ released after all supplies are applied. ++ This is an active high signal to the imx219. ++ ++The imx219 device node should contain one 'port' child node with ++an 'endpoint' subnode. For further reading on port node refer to ++Documentation/devicetree/bindings/media/video-interfaces.txt. ++ ++Endpoint node required properties for CSI-2 connection are: ++- remote-endpoint: a phandle to the bus receiver's endpoint node. ++- clock-lanes: should be set to <0> (clock lane on hardware lane 0) ++- data-lanes: should be set to <1 2>, or <1 2 3 4> (two or four lane CSI-2 ++ supported) ++ ++Example: ++ sensor@10 { ++ compatible = "sony,imx219"; ++ reg = <0x10>; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ clocks = <&imx219_clk>; ++ clock-names = "xclk"; ++ xclr-gpios = <&gpio_sensor 0 0>; ++ DOVDD-supply = <&vgen4_reg>; /* 1.8v */ ++ AVDD-supply = <&vgen3_reg>; /* 2.8v */ ++ DVDD-supply = <&vgen2_reg>; /* 1.2v */ ++ ++ imx219_clk: camera-clk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <24000000>; ++ }; ++ ++ port { ++ sensor_out: endpoint { ++ remote-endpoint = <&csiss_in>; ++ clock-lanes = <0>; ++ data-lanes = <1 2>; ++ }; ++ }; ++ }; -- cgit v1.2.3