From e1f0a7e841750fe8e47b4755fb5f849bcda2b50d Mon Sep 17 00:00:00 2001 From: Felix Fietkau Date: Fri, 11 Sep 2015 17:17:30 +0000 Subject: brcm2708: remove linux 3.18 support Signed-off-by: Felix Fietkau SVN-Revision: 46870 --- .../0030-ASoC-Add-support-for-BCM2708.patch | 1124 -------------------- 1 file changed, 1124 deletions(-) delete mode 100644 target/linux/brcm2708/patches-3.18/0030-ASoC-Add-support-for-BCM2708.patch (limited to 'target/linux/brcm2708/patches-3.18/0030-ASoC-Add-support-for-BCM2708.patch') diff --git a/target/linux/brcm2708/patches-3.18/0030-ASoC-Add-support-for-BCM2708.patch b/target/linux/brcm2708/patches-3.18/0030-ASoC-Add-support-for-BCM2708.patch deleted file mode 100644 index adaf624be4..0000000000 --- a/target/linux/brcm2708/patches-3.18/0030-ASoC-Add-support-for-BCM2708.patch +++ /dev/null @@ -1,1124 +0,0 @@ -From ec589c88e88452a80a20ad4ebc90e8fe5d80e7cd Mon Sep 17 00:00:00 2001 -From: Florian Meier -Date: Fri, 22 Nov 2013 14:33:38 +0100 -Subject: [PATCH 030/114] ASoC: Add support for BCM2708 - -This driver adds support for digital audio (I2S) -for the BCM2708 SoC that is used by the -Raspberry Pi. External audio codecs can be -connected to the Raspberry Pi via P5 header. - -It relies on cyclic DMA engine support for BCM2708. - -Signed-off-by: Florian Meier - -ASoC: BCM2708: Add 24 bit support - -This adds 24 bit support to the I2S driver of the BCM2708. -Besides enabling the 24 bit flags, it includes two bug fixes: - -MMAP is not supported. Claiming this leads to strange issues -when the format of driver and file do not match. - -The datasheet states that the width extension bit should be set -for widths greater than 24, but greater or equal would be correct. -This follows from the definition of the width field. - -Signed-off-by: Florian Meier - -bcm2708-i2s: Update bclk_ratio to more correct values - -Move GPIO setup to hw_params. - -This is used to stop the I2S driver from breaking -the GPIO setup for other uses of the PCM interface - -Configure GPIOs for I2S based on revision/card settings - -With RPi model B+, assignment of the I2S GPIO pins has changed. -This patch uses the board revision to auto-detect the GPIOs used -for I2S. It also allows sound card drivers to set the GPIOs that -should be used. This is especially important with the Compute -Module. - -bcm2708-i2s: Avoid leak from iomap when accessing gpio - -bcm2708: Eliminate i2s debugfs directory error - -Qualify the two regmap ranges uses by bcm2708-i2s ('-i2s' and '-clk') -to avoid the name clash when registering debugfs entries. ---- - sound/soc/bcm/Kconfig | 11 + - sound/soc/bcm/Makefile | 4 + - sound/soc/bcm/bcm2708-i2s.c | 998 ++++++++++++++++++++++++++++++++++++++++++++ - sound/soc/bcm/bcm2708-i2s.h | 35 ++ - 4 files changed, 1048 insertions(+) - create mode 100644 sound/soc/bcm/bcm2708-i2s.c - create mode 100644 sound/soc/bcm/bcm2708-i2s.h - ---- a/sound/soc/bcm/Kconfig -+++ b/sound/soc/bcm/Kconfig -@@ -7,3 +7,14 @@ config SND_BCM2835_SOC_I2S - Say Y or M if you want to add support for codecs attached to - the BCM2835 I2S interface. You will also need - to select the audio interfaces to support below. -+ -+config SND_BCM2708_SOC_I2S -+ tristate "SoC Audio support for the Broadcom BCM2708 I2S module" -+ depends on MACH_BCM2708 -+ select REGMAP_MMIO -+ select SND_SOC_DMAENGINE_PCM -+ select SND_SOC_GENERIC_DMAENGINE_PCM -+ help -+ Say Y or M if you want to add support for codecs attached to -+ the BCM2708 I2S interface. You will also need -+ to select the audio interfaces to support below. ---- a/sound/soc/bcm/Makefile -+++ b/sound/soc/bcm/Makefile -@@ -3,3 +3,7 @@ snd-soc-bcm2835-i2s-objs := bcm2835-i2s. - - obj-$(CONFIG_SND_BCM2835_SOC_I2S) += snd-soc-bcm2835-i2s.o - -+# BCM2708 Platform Support -+snd-soc-bcm2708-i2s-objs := bcm2708-i2s.o -+ -+obj-$(CONFIG_SND_BCM2708_SOC_I2S) += snd-soc-bcm2708-i2s.o ---- /dev/null -+++ b/sound/soc/bcm/bcm2708-i2s.c -@@ -0,0 +1,998 @@ -+/* -+ * ALSA SoC I2S Audio Layer for Broadcom BCM2708 SoC -+ * -+ * Author: Florian Meier -+ * Copyright 2013 -+ * -+ * Based on -+ * Raspberry Pi PCM I2S ALSA Driver -+ * Copyright (c) by Phil Poole 2013 -+ * -+ * ALSA SoC I2S (McBSP) Audio Layer for TI DAVINCI processor -+ * Vladimir Barinov, -+ * Copyright (C) 2007 MontaVista Software, Inc., -+ * -+ * OMAP ALSA SoC DAI driver using McBSP port -+ * Copyright (C) 2008 Nokia Corporation -+ * Contact: Jarkko Nikula -+ * Peter Ujfalusi -+ * -+ * Freescale SSI ALSA SoC Digital Audio Interface (DAI) driver -+ * Author: Timur Tabi -+ * Copyright 2007-2010 Freescale Semiconductor, Inc. -+ * -+ * This program is free software; you can redistribute it and/or -+ * modify it under the terms of the GNU General Public License -+ * version 2 as published by the Free Software Foundation. -+ * -+ * This program is distributed in the hope that it will be useful, but -+ * WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU -+ * General Public License for more details. -+ */ -+ -+#include "bcm2708-i2s.h" -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+#include -+#include -+#include -+#include -+#include -+#include -+ -+#include -+ -+/* Clock registers */ -+#define BCM2708_CLK_PCMCTL_REG 0x00 -+#define BCM2708_CLK_PCMDIV_REG 0x04 -+ -+/* Clock register settings */ -+#define BCM2708_CLK_PASSWD (0x5a000000) -+#define BCM2708_CLK_PASSWD_MASK (0xff000000) -+#define BCM2708_CLK_MASH(v) ((v) << 9) -+#define BCM2708_CLK_FLIP BIT(8) -+#define BCM2708_CLK_BUSY BIT(7) -+#define BCM2708_CLK_KILL BIT(5) -+#define BCM2708_CLK_ENAB BIT(4) -+#define BCM2708_CLK_SRC(v) (v) -+ -+#define BCM2708_CLK_SHIFT (12) -+#define BCM2708_CLK_DIVI(v) ((v) << BCM2708_CLK_SHIFT) -+#define BCM2708_CLK_DIVF(v) (v) -+#define BCM2708_CLK_DIVF_MASK (0xFFF) -+ -+enum { -+ BCM2708_CLK_MASH_0 = 0, -+ BCM2708_CLK_MASH_1, -+ BCM2708_CLK_MASH_2, -+ BCM2708_CLK_MASH_3, -+}; -+ -+enum { -+ BCM2708_CLK_SRC_GND = 0, -+ BCM2708_CLK_SRC_OSC, -+ BCM2708_CLK_SRC_DBG0, -+ BCM2708_CLK_SRC_DBG1, -+ BCM2708_CLK_SRC_PLLA, -+ BCM2708_CLK_SRC_PLLC, -+ BCM2708_CLK_SRC_PLLD, -+ BCM2708_CLK_SRC_HDMI, -+}; -+ -+/* Most clocks are not useable (freq = 0) */ -+static const unsigned int bcm2708_clk_freq[BCM2708_CLK_SRC_HDMI+1] = { -+ [BCM2708_CLK_SRC_GND] = 0, -+ [BCM2708_CLK_SRC_OSC] = 19200000, -+ [BCM2708_CLK_SRC_DBG0] = 0, -+ [BCM2708_CLK_SRC_DBG1] = 0, -+ [BCM2708_CLK_SRC_PLLA] = 0, -+ [BCM2708_CLK_SRC_PLLC] = 0, -+ [BCM2708_CLK_SRC_PLLD] = 500000000, -+ [BCM2708_CLK_SRC_HDMI] = 0, -+}; -+ -+/* I2S registers */ -+#define BCM2708_I2S_CS_A_REG 0x00 -+#define BCM2708_I2S_FIFO_A_REG 0x04 -+#define BCM2708_I2S_MODE_A_REG 0x08 -+#define BCM2708_I2S_RXC_A_REG 0x0c -+#define BCM2708_I2S_TXC_A_REG 0x10 -+#define BCM2708_I2S_DREQ_A_REG 0x14 -+#define BCM2708_I2S_INTEN_A_REG 0x18 -+#define BCM2708_I2S_INTSTC_A_REG 0x1c -+#define BCM2708_I2S_GRAY_REG 0x20 -+ -+/* I2S register settings */ -+#define BCM2708_I2S_STBY BIT(25) -+#define BCM2708_I2S_SYNC BIT(24) -+#define BCM2708_I2S_RXSEX BIT(23) -+#define BCM2708_I2S_RXF BIT(22) -+#define BCM2708_I2S_TXE BIT(21) -+#define BCM2708_I2S_RXD BIT(20) -+#define BCM2708_I2S_TXD BIT(19) -+#define BCM2708_I2S_RXR BIT(18) -+#define BCM2708_I2S_TXW BIT(17) -+#define BCM2708_I2S_CS_RXERR BIT(16) -+#define BCM2708_I2S_CS_TXERR BIT(15) -+#define BCM2708_I2S_RXSYNC BIT(14) -+#define BCM2708_I2S_TXSYNC BIT(13) -+#define BCM2708_I2S_DMAEN BIT(9) -+#define BCM2708_I2S_RXTHR(v) ((v) << 7) -+#define BCM2708_I2S_TXTHR(v) ((v) << 5) -+#define BCM2708_I2S_RXCLR BIT(4) -+#define BCM2708_I2S_TXCLR BIT(3) -+#define BCM2708_I2S_TXON BIT(2) -+#define BCM2708_I2S_RXON BIT(1) -+#define BCM2708_I2S_EN (1) -+ -+#define BCM2708_I2S_CLKDIS BIT(28) -+#define BCM2708_I2S_PDMN BIT(27) -+#define BCM2708_I2S_PDME BIT(26) -+#define BCM2708_I2S_FRXP BIT(25) -+#define BCM2708_I2S_FTXP BIT(24) -+#define BCM2708_I2S_CLKM BIT(23) -+#define BCM2708_I2S_CLKI BIT(22) -+#define BCM2708_I2S_FSM BIT(21) -+#define BCM2708_I2S_FSI BIT(20) -+#define BCM2708_I2S_FLEN(v) ((v) << 10) -+#define BCM2708_I2S_FSLEN(v) (v) -+ -+#define BCM2708_I2S_CHWEX BIT(15) -+#define BCM2708_I2S_CHEN BIT(14) -+#define BCM2708_I2S_CHPOS(v) ((v) << 4) -+#define BCM2708_I2S_CHWID(v) (v) -+#define BCM2708_I2S_CH1(v) ((v) << 16) -+#define BCM2708_I2S_CH2(v) (v) -+ -+#define BCM2708_I2S_TX_PANIC(v) ((v) << 24) -+#define BCM2708_I2S_RX_PANIC(v) ((v) << 16) -+#define BCM2708_I2S_TX(v) ((v) << 8) -+#define BCM2708_I2S_RX(v) (v) -+ -+#define BCM2708_I2S_INT_RXERR BIT(3) -+#define BCM2708_I2S_INT_TXERR BIT(2) -+#define BCM2708_I2S_INT_RXR BIT(1) -+#define BCM2708_I2S_INT_TXW BIT(0) -+ -+/* I2S DMA interface */ -+#define BCM2708_I2S_FIFO_PHYSICAL_ADDR 0x7E203004 -+#define BCM2708_DMA_DREQ_PCM_TX 2 -+#define BCM2708_DMA_DREQ_PCM_RX 3 -+ -+/* I2S pin configuration */ -+static int bcm2708_i2s_gpio=BCM2708_I2S_GPIO_AUTO; -+ -+/* General device struct */ -+struct bcm2708_i2s_dev { -+ struct device *dev; -+ struct snd_dmaengine_dai_dma_data dma_data[2]; -+ unsigned int fmt; -+ unsigned int bclk_ratio; -+ -+ struct regmap *i2s_regmap; -+ struct regmap *clk_regmap; -+}; -+ -+void bcm2708_i2s_set_gpio(int gpio) { -+ bcm2708_i2s_gpio=gpio; -+} -+EXPORT_SYMBOL(bcm2708_i2s_set_gpio); -+ -+ -+static void bcm2708_i2s_start_clock(struct bcm2708_i2s_dev *dev) -+{ -+ /* Start the clock if in master mode */ -+ unsigned int master = dev->fmt & SND_SOC_DAIFMT_MASTER_MASK; -+ -+ switch (master) { -+ case SND_SOC_DAIFMT_CBS_CFS: -+ case SND_SOC_DAIFMT_CBS_CFM: -+ regmap_update_bits(dev->clk_regmap, BCM2708_CLK_PCMCTL_REG, -+ BCM2708_CLK_PASSWD_MASK | BCM2708_CLK_ENAB, -+ BCM2708_CLK_PASSWD | BCM2708_CLK_ENAB); -+ break; -+ default: -+ break; -+ } -+} -+ -+static void bcm2708_i2s_stop_clock(struct bcm2708_i2s_dev *dev) -+{ -+ uint32_t clkreg; -+ int timeout = 1000; -+ -+ /* Stop clock */ -+ regmap_update_bits(dev->clk_regmap, BCM2708_CLK_PCMCTL_REG, -+ BCM2708_CLK_PASSWD_MASK | BCM2708_CLK_ENAB, -+ BCM2708_CLK_PASSWD); -+ -+ /* Wait for the BUSY flag going down */ -+ while (--timeout) { -+ regmap_read(dev->clk_regmap, BCM2708_CLK_PCMCTL_REG, &clkreg); -+ if (!(clkreg & BCM2708_CLK_BUSY)) -+ break; -+ } -+ -+ if (!timeout) { -+ /* KILL the clock */ -+ dev_err(dev->dev, "I2S clock didn't stop. Kill the clock!\n"); -+ regmap_update_bits(dev->clk_regmap, BCM2708_CLK_PCMCTL_REG, -+ BCM2708_CLK_KILL | BCM2708_CLK_PASSWD_MASK, -+ BCM2708_CLK_KILL | BCM2708_CLK_PASSWD); -+ } -+} -+ -+static void bcm2708_i2s_clear_fifos(struct bcm2708_i2s_dev *dev, -+ bool tx, bool rx) -+{ -+ int timeout = 1000; -+ uint32_t syncval; -+ uint32_t csreg; -+ uint32_t i2s_active_state; -+ uint32_t clkreg; -+ uint32_t clk_active_state; -+ uint32_t off; -+ uint32_t clr; -+ -+ off = tx ? BCM2708_I2S_TXON : 0; -+ off |= rx ? BCM2708_I2S_RXON : 0; -+ -+ clr = tx ? BCM2708_I2S_TXCLR : 0; -+ clr |= rx ? BCM2708_I2S_RXCLR : 0; -+ -+ /* Backup the current state */ -+ regmap_read(dev->i2s_regmap, BCM2708_I2S_CS_A_REG, &csreg); -+ i2s_active_state = csreg & (BCM2708_I2S_RXON | BCM2708_I2S_TXON); -+ -+ regmap_read(dev->clk_regmap, BCM2708_CLK_PCMCTL_REG, &clkreg); -+ clk_active_state = clkreg & BCM2708_CLK_ENAB; -+ -+ /* Start clock if not running */ -+ if (!clk_active_state) { -+ regmap_update_bits(dev->clk_regmap, BCM2708_CLK_PCMCTL_REG, -+ BCM2708_CLK_PASSWD_MASK | BCM2708_CLK_ENAB, -+ BCM2708_CLK_PASSWD | BCM2708_CLK_ENAB); -+ } -+ -+ /* Stop I2S module */ -+ regmap_update_bits(dev->i2s_regmap, BCM2708_I2S_CS_A_REG, off, 0); -+ -+ /* -+ * Clear the FIFOs -+ * Requires at least 2 PCM clock cycles to take effect -+ */ -+ regmap_update_bits(dev->i2s_regmap, BCM2708_I2S_CS_A_REG, clr, clr); -+ -+ /* Wait for 2 PCM clock cycles */ -+ -+ /* -+ * Toggle the SYNC flag. After 2 PCM clock cycles it can be read back -+ * FIXME: This does not seem to work for slave mode! -+ */ -+ regmap_read(dev->i2s_regmap, BCM2708_I2S_CS_A_REG, &syncval); -+ syncval &= BCM2708_I2S_SYNC; -+ -+ regmap_update_bits(dev->i2s_regmap, BCM2708_I2S_CS_A_REG, -+ BCM2708_I2S_SYNC, ~syncval); -+ -+ /* Wait for the SYNC flag changing it's state */ -+ while (--timeout) { -+ regmap_read(dev->i2s_regmap, BCM2708_I2S_CS_A_REG, &csreg); -+ if ((csreg & BCM2708_I2S_SYNC) != syncval) -+ break; -+ } -+ -+ if (!timeout) -+ dev_err(dev->dev, "I2S SYNC error!\n"); -+ -+ /* Stop clock if it was not running before */ -+ if (!clk_active_state) -+ bcm2708_i2s_stop_clock(dev); -+ -+ /* Restore I2S state */ -+ regmap_update_bits(dev->i2s_regmap, BCM2708_I2S_CS_A_REG, -+ BCM2708_I2S_RXON | BCM2708_I2S_TXON, i2s_active_state); -+} -+ -+static int bcm2708_i2s_set_dai_fmt(struct snd_soc_dai *dai, -+ unsigned int fmt) -+{ -+ struct bcm2708_i2s_dev *dev = snd_soc_dai_get_drvdata(dai); -+ dev->fmt = fmt; -+ return 0; -+} -+ -+static int bcm2708_i2s_set_dai_bclk_ratio(struct snd_soc_dai *dai, -+ unsigned int ratio) -+{ -+ struct bcm2708_i2s_dev *dev = snd_soc_dai_get_drvdata(dai); -+ dev->bclk_ratio = ratio; -+ return 0; -+} -+ -+ -+static int bcm2708_i2s_set_function(unsigned offset, int function) -+{ -+ #define GPIOFSEL(x) (0x00+(x)*4) -+ void __iomem *gpio = __io_address(GPIO_BASE); -+ unsigned alt = function <= 3 ? function + 4: function == 4 ? 3 : 2; -+ unsigned gpiodir; -+ unsigned gpio_bank = offset / 10; -+ unsigned gpio_field_offset = (offset - 10 * gpio_bank) * 3; -+ -+ if (offset >= BCM2708_NR_GPIOS) -+ return -EINVAL; -+ -+ gpiodir = readl(gpio + GPIOFSEL(gpio_bank)); -+ gpiodir &= ~(7 << gpio_field_offset); -+ gpiodir |= alt << gpio_field_offset; -+ writel(gpiodir, gpio + GPIOFSEL(gpio_bank)); -+ return 0; -+} -+ -+static void bcm2708_i2s_setup_gpio(void) -+{ -+ /* -+ * This is the common way to handle the GPIO pins for -+ * the Raspberry Pi. -+ * TODO Better way would be to handle -+ * this in the device tree! -+ */ -+ int pin,pinconfig,startpin,alt; -+ -+ /* SPI is on different GPIOs on different boards */ -+ /* for Raspberry Pi B+, this is pin GPIO18-21, for original on 28-31 */ -+ if (bcm2708_i2s_gpio==BCM2708_I2S_GPIO_AUTO) { -+ if ((system_rev & 0xffffff) >= 0x10) { -+ /* Model B+ */ -+ pinconfig=BCM2708_I2S_GPIO_PIN18; -+ } else { -+ /* original */ -+ pinconfig=BCM2708_I2S_GPIO_PIN28; -+ } -+ } else { -+ pinconfig=bcm2708_i2s_gpio; -+ } -+ -+ if (pinconfig==BCM2708_I2S_GPIO_PIN18) { -+ startpin=18; -+ alt=BCM2708_I2S_GPIO_PIN18_ALT; -+ } else if (pinconfig==BCM2708_I2S_GPIO_PIN28) { -+ startpin=28; -+ alt=BCM2708_I2S_GPIO_PIN28_ALT; -+ } else { -+ printk(KERN_INFO "Can't configure I2S GPIOs, unknown pin mode for I2S: %i\n",pinconfig); -+ return; -+ } -+ -+ /* configure I2S pins to correct ALT mode */ -+ for (pin = startpin; pin <= startpin+3; pin++) { -+ bcm2708_i2s_set_function(pin, alt); -+ } -+} -+ -+static int bcm2708_i2s_hw_params(struct snd_pcm_substream *substream, -+ struct snd_pcm_hw_params *params, -+ struct snd_soc_dai *dai) -+{ -+ struct bcm2708_i2s_dev *dev = snd_soc_dai_get_drvdata(dai); -+ -+ unsigned int sampling_rate = params_rate(params); -+ unsigned int data_length, data_delay, bclk_ratio; -+ unsigned int ch1pos, ch2pos, mode, format; -+ unsigned int mash = BCM2708_CLK_MASH_1; -+ unsigned int divi, divf, target_frequency; -+ int clk_src = -1; -+ unsigned int master = dev->fmt & SND_SOC_DAIFMT_MASTER_MASK; -+ bool bit_master = (master == SND_SOC_DAIFMT_CBS_CFS -+ || master == SND_SOC_DAIFMT_CBS_CFM); -+ -+ bool frame_master = (master == SND_SOC_DAIFMT_CBS_CFS -+ || master == SND_SOC_DAIFMT_CBM_CFS); -+ uint32_t csreg; -+ -+ /* -+ * If a stream is already enabled, -+ * the registers are already set properly. -+ */ -+ regmap_read(dev->i2s_regmap, BCM2708_I2S_CS_A_REG, &csreg); -+ -+ if (csreg & (BCM2708_I2S_TXON | BCM2708_I2S_RXON)) -+ return 0; -+ -+ -+ bcm2708_i2s_setup_gpio(); -+ -+ /* -+ * Adjust the data length according to the format. -+ * We prefill the half frame length with an integer -+ * divider of 2400 as explained at the clock settings. -+ * Maybe it is overwritten there, if the Integer mode -+ * does not apply. -+ */ -+ switch (params_format(params)) { -+ case SNDRV_PCM_FORMAT_S16_LE: -+ data_length = 16; -+ bclk_ratio = 50; -+ break; -+ case SNDRV_PCM_FORMAT_S24_LE: -+ data_length = 24; -+ bclk_ratio = 50; -+ break; -+ case SNDRV_PCM_FORMAT_S32_LE: -+ data_length = 32; -+ bclk_ratio = 100; -+ break; -+ default: -+ return -EINVAL; -+ } -+ -+ /* If bclk_ratio already set, use that one. */ -+ if (dev->bclk_ratio) -+ bclk_ratio = dev->bclk_ratio; -+ -+ /* -+ * Clock Settings -+ * -+ * The target frequency of the bit clock is -+ * sampling rate * frame length -+ * -+ * Integer mode: -+ * Sampling rates that are multiples of 8000 kHz -+ * can be driven by the oscillator of 19.2 MHz -+ * with an integer divider as long as the frame length -+ * is an integer divider of 19200000/8000=2400 as set up above. -+ * This is no longer possible if the sampling rate -+ * is too high (e.g. 192 kHz), because the oscillator is too slow. -+ * -+ * MASH mode: -+ * For all other sampling rates, it is not possible to -+ * have an integer divider. Approximate the clock -+ * with the MASH module that induces a slight frequency -+ * variance. To minimize that it is best to have the fastest -+ * clock here. That is PLLD with 500 MHz. -+ */ -+ target_frequency = sampling_rate * bclk_ratio; -+ clk_src = BCM2708_CLK_SRC_OSC; -+ mash = BCM2708_CLK_MASH_0; -+ -+ if (bcm2708_clk_freq[clk_src] % target_frequency == 0 -+ && bit_master && frame_master) { -+ divi = bcm2708_clk_freq[clk_src] / target_frequency; -+ divf = 0; -+ } else { -+ uint64_t dividend; -+ -+ if (!dev->bclk_ratio) { -+ /* -+ * Overwrite bclk_ratio, because the -+ * above trick is not needed or can -+ * not be used. -+ */ -+ bclk_ratio = 2 * data_length; -+ } -+ -+ target_frequency = sampling_rate * bclk_ratio; -+ -+ clk_src = BCM2708_CLK_SRC_PLLD; -+ mash = BCM2708_CLK_MASH_1; -+ -+ dividend = bcm2708_clk_freq[clk_src]; -+ dividend <<= BCM2708_CLK_SHIFT; -+ do_div(dividend, target_frequency); -+ divi = dividend >> BCM2708_CLK_SHIFT; -+ divf = dividend & BCM2708_CLK_DIVF_MASK; -+ } -+ -+ /* Set clock divider */ -+ regmap_write(dev->clk_regmap, BCM2708_CLK_PCMDIV_REG, BCM2708_CLK_PASSWD -+ | BCM2708_CLK_DIVI(divi) -+ | BCM2708_CLK_DIVF(divf)); -+ -+ /* Setup clock, but don't start it yet */ -+ regmap_write(dev->clk_regmap, BCM2708_CLK_PCMCTL_REG, BCM2708_CLK_PASSWD -+ | BCM2708_CLK_MASH(mash) -+ | BCM2708_CLK_SRC(clk_src)); -+ -+ /* Setup the frame format */ -+ format = BCM2708_I2S_CHEN; -+ -+ if (data_length >= 24) -+ format |= BCM2708_I2S_CHWEX; -+ -+ format |= BCM2708_I2S_CHWID((data_length-8)&0xf); -+ -+ switch (dev->fmt & SND_SOC_DAIFMT_FORMAT_MASK) { -+ case SND_SOC_DAIFMT_I2S: -+ data_delay = 1; -+ break; -+ default: -+ /* -+ * TODO -+ * Others are possible but are not implemented at the moment. -+ */ -+ dev_err(dev->dev, "%s:bad format\n", __func__); -+ return -EINVAL; -+ } -+ -+ ch1pos = data_delay; -+ ch2pos = bclk_ratio / 2 + data_delay; -+ -+ switch (params_channels(params)) { -+ case 2: -+ format = BCM2708_I2S_CH1(format) | BCM2708_I2S_CH2(format); -+ format |= BCM2708_I2S_CH1(BCM2708_I2S_CHPOS(ch1pos)); -+ format |= BCM2708_I2S_CH2(BCM2708_I2S_CHPOS(ch2pos)); -+ break; -+ default: -+ return -EINVAL; -+ } -+ -+ /* -+ * Set format for both streams. -+ * We cannot set another frame length -+ * (and therefore word length) anyway, -+ * so the format will be the same. -+ */ -+ regmap_write(dev->i2s_regmap, BCM2708_I2S_RXC_A_REG, format); -+ regmap_write(dev->i2s_regmap, BCM2708_I2S_TXC_A_REG, format); -+ -+ /* Setup the I2S mode */ -+ mode = 0; -+ -+ if (data_length <= 16) { -+ /* -+ * Use frame packed mode (2 channels per 32 bit word) -+ * We cannot set another frame length in the second stream -+ * (and therefore word length) anyway, -+ * so the format will be the same. -+ */ -+ mode |= BCM2708_I2S_FTXP | BCM2708_I2S_FRXP; -+ } -+ -+ mode |= BCM2708_I2S_FLEN(bclk_ratio - 1); -+ mode |= BCM2708_I2S_FSLEN(bclk_ratio / 2); -+ -+ /* Master or slave? */ -+ switch (dev->fmt & SND_SOC_DAIFMT_MASTER_MASK) { -+ case SND_SOC_DAIFMT_CBS_CFS: -+ /* CPU is master */ -+ break; -+ case SND_SOC_DAIFMT_CBM_CFS: -+ /* -+ * CODEC is bit clock master -+ * CPU is frame master -+ */ -+ mode |= BCM2708_I2S_CLKM; -+ break; -+ case SND_SOC_DAIFMT_CBS_CFM: -+ /* -+ * CODEC is frame master -+ * CPU is bit clock master -+ */ -+ mode |= BCM2708_I2S_FSM; -+ break; -+ case SND_SOC_DAIFMT_CBM_CFM: -+ /* CODEC is master */ -+ mode |= BCM2708_I2S_CLKM; -+ mode |= BCM2708_I2S_FSM; -+ break; -+ default: -+ dev_err(dev->dev, "%s:bad master\n", __func__); -+ return -EINVAL; -+ } -+ -+ /* -+ * Invert clocks? -+ * -+ * The BCM approach seems to be inverted to the classical I2S approach. -+ */ -+ switch (dev->fmt & SND_SOC_DAIFMT_INV_MASK) { -+ case SND_SOC_DAIFMT_NB_NF: -+ /* None. Therefore, both for BCM */ -+ mode |= BCM2708_I2S_CLKI; -+ mode |= BCM2708_I2S_FSI; -+ break; -+ case SND_SOC_DAIFMT_IB_IF: -+ /* Both. Therefore, none for BCM */ -+ break; -+ case SND_SOC_DAIFMT_NB_IF: -+ /* -+ * Invert only frame sync. Therefore, -+ * invert only bit clock for BCM -+ */ -+ mode |= BCM2708_I2S_CLKI; -+ break; -+ case SND_SOC_DAIFMT_IB_NF: -+ /* -+ * Invert only bit clock. Therefore, -+ * invert only frame sync for BCM -+ */ -+ mode |= BCM2708_I2S_FSI; -+ break; -+ default: -+ return -EINVAL; -+ } -+ -+ regmap_write(dev->i2s_regmap, BCM2708_I2S_MODE_A_REG, mode); -+ -+ /* Setup the DMA parameters */ -+ regmap_update_bits(dev->i2s_regmap, BCM2708_I2S_CS_A_REG, -+ BCM2708_I2S_RXTHR(1) -+ | BCM2708_I2S_TXTHR(1) -+ | BCM2708_I2S_DMAEN, 0xffffffff); -+ -+ regmap_update_bits(dev->i2s_regmap, BCM2708_I2S_DREQ_A_REG, -+ BCM2708_I2S_TX_PANIC(0x10) -+ | BCM2708_I2S_RX_PANIC(0x30) -+ | BCM2708_I2S_TX(0x30) -+ | BCM2708_I2S_RX(0x20), 0xffffffff); -+ -+ /* Clear FIFOs */ -+ bcm2708_i2s_clear_fifos(dev, true, true); -+ -+ return 0; -+} -+ -+static int bcm2708_i2s_prepare(struct snd_pcm_substream *substream, -+ struct snd_soc_dai *dai) -+{ -+ struct bcm2708_i2s_dev *dev = snd_soc_dai_get_drvdata(dai); -+ uint32_t cs_reg; -+ -+ bcm2708_i2s_start_clock(dev); -+ -+ /* -+ * Clear both FIFOs if the one that should be started -+ * is not empty at the moment. This should only happen -+ * after overrun. Otherwise, hw_params would have cleared -+ * the FIFO. -+ */ -+ regmap_read(dev->i2s_regmap, BCM2708_I2S_CS_A_REG, &cs_reg); -+ -+ if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK -+ && !(cs_reg & BCM2708_I2S_TXE)) -+ bcm2708_i2s_clear_fifos(dev, true, false); -+ else if (substream->stream == SNDRV_PCM_STREAM_CAPTURE -+ && (cs_reg & BCM2708_I2S_RXD)) -+ bcm2708_i2s_clear_fifos(dev, false, true); -+ -+ return 0; -+} -+ -+static void bcm2708_i2s_stop(struct bcm2708_i2s_dev *dev, -+ struct snd_pcm_substream *substream, -+ struct snd_soc_dai *dai) -+{ -+ uint32_t mask; -+ -+ if (substream->stream == SNDRV_PCM_STREAM_CAPTURE) -+ mask = BCM2708_I2S_RXON; -+ else -+ mask = BCM2708_I2S_TXON; -+ -+ regmap_update_bits(dev->i2s_regmap, -+ BCM2708_I2S_CS_A_REG, mask, 0); -+ -+ /* Stop also the clock when not SND_SOC_DAIFMT_CONT */ -+ if (!dai->active && !(dev->fmt & SND_SOC_DAIFMT_CONT)) -+ bcm2708_i2s_stop_clock(dev); -+} -+ -+static int bcm2708_i2s_trigger(struct snd_pcm_substream *substream, int cmd, -+ struct snd_soc_dai *dai) -+{ -+ struct bcm2708_i2s_dev *dev = snd_soc_dai_get_drvdata(dai); -+ uint32_t mask; -+ -+ switch (cmd) { -+ case SNDRV_PCM_TRIGGER_START: -+ case SNDRV_PCM_TRIGGER_RESUME: -+ case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: -+ bcm2708_i2s_start_clock(dev); -+ -+ if (substream->stream == SNDRV_PCM_STREAM_CAPTURE) -+ mask = BCM2708_I2S_RXON; -+ else -+ mask = BCM2708_I2S_TXON; -+ -+ regmap_update_bits(dev->i2s_regmap, -+ BCM2708_I2S_CS_A_REG, mask, mask); -+ break; -+ -+ case SNDRV_PCM_TRIGGER_STOP: -+ case SNDRV_PCM_TRIGGER_SUSPEND: -+ case SNDRV_PCM_TRIGGER_PAUSE_PUSH: -+ bcm2708_i2s_stop(dev, substream, dai); -+ break; -+ default: -+ return -EINVAL; -+ } -+ -+ return 0; -+} -+ -+static int bcm2708_i2s_startup(struct snd_pcm_substream *substream, -+ struct snd_soc_dai *dai) -+{ -+ struct bcm2708_i2s_dev *dev = snd_soc_dai_get_drvdata(dai); -+ -+ if (dai->active) -+ return 0; -+ -+ /* Should this still be running stop it */ -+ bcm2708_i2s_stop_clock(dev); -+ -+ /* Enable PCM block */ -+ regmap_update_bits(dev->i2s_regmap, BCM2708_I2S_CS_A_REG, -+ BCM2708_I2S_EN, BCM2708_I2S_EN); -+ -+ /* -+ * Disable STBY. -+ * Requires at least 4 PCM clock cycles to take effect. -+ */ -+ regmap_update_bits(dev->i2s_regmap, BCM2708_I2S_CS_A_REG, -+ BCM2708_I2S_STBY, BCM2708_I2S_STBY); -+ -+ return 0; -+} -+ -+static void bcm2708_i2s_shutdown(struct snd_pcm_substream *substream, -+ struct snd_soc_dai *dai) -+{ -+ struct bcm2708_i2s_dev *dev = snd_soc_dai_get_drvdata(dai); -+ -+ bcm2708_i2s_stop(dev, substream, dai); -+ -+ /* If both streams are stopped, disable module and clock */ -+ if (dai->active) -+ return; -+ -+ /* Disable the module */ -+ regmap_update_bits(dev->i2s_regmap, BCM2708_I2S_CS_A_REG, -+ BCM2708_I2S_EN, 0); -+ -+ /* -+ * Stopping clock is necessary, because stop does -+ * not stop the clock when SND_SOC_DAIFMT_CONT -+ */ -+ bcm2708_i2s_stop_clock(dev); -+} -+ -+static const struct snd_soc_dai_ops bcm2708_i2s_dai_ops = { -+ .startup = bcm2708_i2s_startup, -+ .shutdown = bcm2708_i2s_shutdown, -+ .prepare = bcm2708_i2s_prepare, -+ .trigger = bcm2708_i2s_trigger, -+ .hw_params = bcm2708_i2s_hw_params, -+ .set_fmt = bcm2708_i2s_set_dai_fmt, -+ .set_bclk_ratio = bcm2708_i2s_set_dai_bclk_ratio -+}; -+ -+static int bcm2708_i2s_dai_probe(struct snd_soc_dai *dai) -+{ -+ struct bcm2708_i2s_dev *dev = snd_soc_dai_get_drvdata(dai); -+ -+ dai->playback_dma_data = &dev->dma_data[SNDRV_PCM_STREAM_PLAYBACK]; -+ dai->capture_dma_data = &dev->dma_data[SNDRV_PCM_STREAM_CAPTURE]; -+ -+ return 0; -+} -+ -+static struct snd_soc_dai_driver bcm2708_i2s_dai = { -+ .name = "bcm2708-i2s", -+ .probe = bcm2708_i2s_dai_probe, -+ .playback = { -+ .channels_min = 2, -+ .channels_max = 2, -+ .rates = SNDRV_PCM_RATE_8000_192000, -+ .formats = SNDRV_PCM_FMTBIT_S16_LE -+ | SNDRV_PCM_FMTBIT_S24_LE -+ | SNDRV_PCM_FMTBIT_S32_LE -+ }, -+ .capture = { -+ .channels_min = 2, -+ .channels_max = 2, -+ .rates = SNDRV_PCM_RATE_8000_192000, -+ .formats = SNDRV_PCM_FMTBIT_S16_LE -+ | SNDRV_PCM_FMTBIT_S24_LE -+ | SNDRV_PCM_FMTBIT_S32_LE -+ }, -+ .ops = &bcm2708_i2s_dai_ops, -+ .symmetric_rates = 1 -+}; -+ -+static bool bcm2708_i2s_volatile_reg(struct device *dev, unsigned int reg) -+{ -+ switch (reg) { -+ case BCM2708_I2S_CS_A_REG: -+ case BCM2708_I2S_FIFO_A_REG: -+ case BCM2708_I2S_INTSTC_A_REG: -+ case BCM2708_I2S_GRAY_REG: -+ return true; -+ default: -+ return false; -+ }; -+} -+ -+static bool bcm2708_i2s_precious_reg(struct device *dev, unsigned int reg) -+{ -+ switch (reg) { -+ case BCM2708_I2S_FIFO_A_REG: -+ return true; -+ default: -+ return false; -+ }; -+} -+ -+static bool bcm2708_clk_volatile_reg(struct device *dev, unsigned int reg) -+{ -+ switch (reg) { -+ case BCM2708_CLK_PCMCTL_REG: -+ return true; -+ default: -+ return false; -+ }; -+} -+ -+static const struct regmap_config bcm2708_regmap_config[] = { -+ { -+ .reg_bits = 32, -+ .reg_stride = 4, -+ .val_bits = 32, -+ .max_register = BCM2708_I2S_GRAY_REG, -+ .precious_reg = bcm2708_i2s_precious_reg, -+ .volatile_reg = bcm2708_i2s_volatile_reg, -+ .cache_type = REGCACHE_RBTREE, -+ .name = "i2s", -+ }, -+ { -+ .reg_bits = 32, -+ .reg_stride = 4, -+ .val_bits = 32, -+ .max_register = BCM2708_CLK_PCMDIV_REG, -+ .volatile_reg = bcm2708_clk_volatile_reg, -+ .cache_type = REGCACHE_RBTREE, -+ .name = "clk", -+ }, -+}; -+ -+static const struct snd_soc_component_driver bcm2708_i2s_component = { -+ .name = "bcm2708-i2s-comp", -+}; -+ -+static const struct snd_pcm_hardware bcm2708_pcm_hardware = { -+ .info = SNDRV_PCM_INFO_INTERLEAVED | -+ SNDRV_PCM_INFO_JOINT_DUPLEX, -+ .formats = SNDRV_PCM_FMTBIT_S16_LE | -+ SNDRV_PCM_FMTBIT_S24_LE | -+ SNDRV_PCM_FMTBIT_S32_LE, -+ .period_bytes_min = 32, -+ .period_bytes_max = 64 * PAGE_SIZE, -+ .periods_min = 2, -+ .periods_max = 255, -+ .buffer_bytes_max = 128 * PAGE_SIZE, -+}; -+ -+static const struct snd_dmaengine_pcm_config bcm2708_dmaengine_pcm_config = { -+ .prepare_slave_config = snd_dmaengine_pcm_prepare_slave_config, -+ .pcm_hardware = &bcm2708_pcm_hardware, -+ .prealloc_buffer_size = 256 * PAGE_SIZE, -+}; -+ -+ -+static int bcm2708_i2s_probe(struct platform_device *pdev) -+{ -+ struct bcm2708_i2s_dev *dev; -+ int i; -+ int ret; -+ struct regmap *regmap[2]; -+ struct resource *mem[2]; -+ -+ /* Request both ioareas */ -+ for (i = 0; i <= 1; i++) { -+ void __iomem *base; -+ -+ mem[i] = platform_get_resource(pdev, IORESOURCE_MEM, i); -+ base = devm_ioremap_resource(&pdev->dev, mem[i]); -+ if (IS_ERR(base)) -+ return PTR_ERR(base); -+ -+ regmap[i] = devm_regmap_init_mmio(&pdev->dev, base, -+ &bcm2708_regmap_config[i]); -+ if (IS_ERR(regmap[i])) { -+ dev_err(&pdev->dev, "I2S probe: regmap init failed\n"); -+ return PTR_ERR(regmap[i]); -+ } -+ } -+ -+ dev = devm_kzalloc(&pdev->dev, sizeof(*dev), -+ GFP_KERNEL); -+ if (IS_ERR(dev)) -+ return PTR_ERR(dev); -+ -+ dev->i2s_regmap = regmap[0]; -+ dev->clk_regmap = regmap[1]; -+ -+ /* Set the DMA address */ -+ dev->dma_data[SNDRV_PCM_STREAM_PLAYBACK].addr = -+ (dma_addr_t)BCM2708_I2S_FIFO_PHYSICAL_ADDR; -+ -+ dev->dma_data[SNDRV_PCM_STREAM_CAPTURE].addr = -+ (dma_addr_t)BCM2708_I2S_FIFO_PHYSICAL_ADDR; -+ -+ /* Set the DREQ */ -+ dev->dma_data[SNDRV_PCM_STREAM_PLAYBACK].slave_id = -+ BCM2708_DMA_DREQ_PCM_TX; -+ dev->dma_data[SNDRV_PCM_STREAM_CAPTURE].slave_id = -+ BCM2708_DMA_DREQ_PCM_RX; -+ -+ /* Set the bus width */ -+ dev->dma_data[SNDRV_PCM_STREAM_PLAYBACK].addr_width = -+ DMA_SLAVE_BUSWIDTH_4_BYTES; -+ dev->dma_data[SNDRV_PCM_STREAM_CAPTURE].addr_width = -+ DMA_SLAVE_BUSWIDTH_4_BYTES; -+ -+ /* Set burst */ -+ dev->dma_data[SNDRV_PCM_STREAM_PLAYBACK].maxburst = 2; -+ dev->dma_data[SNDRV_PCM_STREAM_CAPTURE].maxburst = 2; -+ -+ /* BCLK ratio - use default */ -+ dev->bclk_ratio = 0; -+ -+ /* Store the pdev */ -+ dev->dev = &pdev->dev; -+ dev_set_drvdata(&pdev->dev, dev); -+ -+ ret = snd_soc_register_component(&pdev->dev, -+ &bcm2708_i2s_component, &bcm2708_i2s_dai, 1); -+ -+ if (ret) { -+ dev_err(&pdev->dev, "Could not register DAI: %d\n", ret); -+ ret = -ENOMEM; -+ return ret; -+ } -+ -+ ret = snd_dmaengine_pcm_register(&pdev->dev, -+ &bcm2708_dmaengine_pcm_config, -+ SND_DMAENGINE_PCM_FLAG_COMPAT); -+ if (ret) { -+ dev_err(&pdev->dev, "Could not register PCM: %d\n", ret); -+ snd_soc_unregister_component(&pdev->dev); -+ return ret; -+ } -+ -+ return 0; -+} -+ -+static int bcm2708_i2s_remove(struct platform_device *pdev) -+{ -+ snd_dmaengine_pcm_unregister(&pdev->dev); -+ snd_soc_unregister_component(&pdev->dev); -+ return 0; -+} -+ -+static struct platform_driver bcm2708_i2s_driver = { -+ .probe = bcm2708_i2s_probe, -+ .remove = bcm2708_i2s_remove, -+ .driver = { -+ .name = "bcm2708-i2s", -+ .owner = THIS_MODULE, -+ }, -+}; -+ -+module_platform_driver(bcm2708_i2s_driver); -+ -+MODULE_ALIAS("platform:bcm2708-i2s"); -+MODULE_DESCRIPTION("BCM2708 I2S interface"); -+MODULE_AUTHOR("Florian Meier "); -+MODULE_LICENSE("GPL v2"); ---- /dev/null -+++ b/sound/soc/bcm/bcm2708-i2s.h -@@ -0,0 +1,35 @@ -+/* -+ * I2S configuration for sound cards. -+ * -+ * Copyright (c) 2014 Daniel Matuschek -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License as published by -+ * the Free Software Foundation; either version 2 of the License, or -+ * (at your option) any later version. -+ * -+ * This program is distributed in the hope that it will be useful, -+ * but WITHOUT ANY WARRANTY; without even the implied warranty of -+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -+ * GNU General Public License for more details. -+ * -+ * You should have received a copy of the GNU General Public License -+ * along with this program; if not, write to the Free Software -+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA -+ */ -+ -+#ifndef BCM2708_I2S_H -+#define BCM2708_I2S_H -+ -+/* I2S pin assignment */ -+#define BCM2708_I2S_GPIO_AUTO 0 -+#define BCM2708_I2S_GPIO_PIN18 1 -+#define BCM2708_I2S_GPIO_PIN28 2 -+ -+/* Alt mode to enable I2S */ -+#define BCM2708_I2S_GPIO_PIN18_ALT 0 -+#define BCM2708_I2S_GPIO_PIN28_ALT 2 -+ -+extern void bcm2708_i2s_set_gpio(int gpio); -+ -+#endif -- cgit v1.2.3