From 59c2f9eaad5688af523ff60d2f83d5d81447009b Mon Sep 17 00:00:00 2001 From: Daniele Castro Date: Thu, 10 Sep 2020 21:14:11 +0200 Subject: bcm63xx: add support for Technicolor TG582n MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Technicolor TG582n has a similar PCB as the OpenWrt's ADB P.DG A4001N1 with LEDs connected to different GPIO PINs in active low configuration. Hardware: * Board ID: DANT-1 * SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350 * RAM DDR2: 64 Mbyte - Winbond W9751G6KB-25 * Serial flash: 16 Mbyte - MXIC MX25L6445EMI * Ethernet: 4x Ethernet 10/100 baseT * Wifi 2.4GHz: Broadcom Corporation BCM43227 Wireless Network Adapter (rev 30) * LEDs: 2x Power, 1x Ethernet, 1x Broadband, 2x Wi-Fi, 2x WPS, 4x ethernet * Buttons: 1x Reset, 1x WPS, 1x WiFi * UART: 1x TTL 115200n8, VCC GND TX RX, on J3 connector (short R62 and R63) Installation via CFE: * Stock CFE has to be overwritten with a generic 6328 one that can upload .bin images with no signature check (cfe6328_configured.bin) * Connect a serial port to the board * Stop the CFE boot process after power on by pressing enter * Set static IP 192.168.2.10 and subnet mask 255.255.255.0 * Navigate to http://192.168.2.50/ * Upload the OpenWrt image file PCB: |GPIO: |TG582n: LED2R |488(08) |red Power LED2G |484(04) |green Power LED10R |486(06) | LED13G |485(05) |green Ethernet LED11R |494(14) | LED14G |491(11) |green Broadband LED5R |487(07) |red Internet LED5G |481(01) |green Internet LED12R |498(18) | LED12G |499(19) | LED6R |482(02) |red Wi-Fi LED6G |483(03) |green Wi-Fi LED7R |490(10) |red WPS LED7G |489(09) |green WPS LED4 |508(28) |ethernet port 4 LED3 |507(27) |ethernet port 3 LED9 |506(26) |ethernet port 2 LED8 |505(25) |ethernet port 1 SW3 |503(23) |key Reset SW5 |504(24) |key WPS SW4 |495(15) |key Wi-Fi SW6 |493(13) | SW1 |492(12) | Signed-off-by: Daniele Castro [Fix base-files, refresh patch] Signed-off-by: Álvaro Fernández Rojas --- .../bcm63xx/patches-5.4/512-board_bcm6328.patch | 51 ++++++++++++++++++++-- 1 file changed, 48 insertions(+), 3 deletions(-) (limited to 'target/linux/bcm63xx/patches-5.4/512-board_bcm6328.patch') diff --git a/target/linux/bcm63xx/patches-5.4/512-board_bcm6328.patch b/target/linux/bcm63xx/patches-5.4/512-board_bcm6328.patch index ebe1ac4d94..ae0c538660 100644 --- a/target/linux/bcm63xx/patches-5.4/512-board_bcm6328.patch +++ b/target/linux/bcm63xx/patches-5.4/512-board_bcm6328.patch @@ -1,6 +1,6 @@ --- a/arch/mips/bcm63xx/boards/board_bcm963xx.c +++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -348,6 +348,568 @@ static struct board_info __initdata boar +@@ -348,6 +348,611 @@ static struct board_info __initdata boar }, }, }; @@ -524,6 +524,49 @@ + }, +}; + ++static struct board_info __initdata board_TG582N = { ++ .name = "DANT-1", ++ .expected_cpu_id = 0x6328, ++ ++ .has_pci = 1, ++ .has_ohci0 = 1, ++ .has_ehci0 = 1, ++ .num_usbh_ports = 1, ++ ++ .has_enetsw = 1, ++ .enetsw = { ++ .used_ports = { ++ [0] = { ++ .used = 1, ++ .phy_id = 1, ++ .name = "Port 1", ++ }, ++ [1] = { ++ .used = 1, ++ .phy_id = 2, ++ .name = "Port 2", ++ }, ++ [2] = { ++ .used = 1, ++ .phy_id = 3, ++ .name = "Port 3", ++ }, ++ [3] = { ++ .used = 1, ++ .phy_id = 4, ++ .name = "Port 4", ++ }, ++ }, ++ }, ++ ++ .use_fallback_sprom = 1, ++ .fallback_sprom = { ++ .type = SPROM_BCM43225, ++ .pci_bus = 1, ++ .pci_dev = 0, ++ }, ++}; ++ +static struct board_info __initdata board_TG582N_TELECOM_ITALIA = { + .name = "DANT-V", + .expected_cpu_id = 0x6328, @@ -569,7 +612,7 @@ #endif /* CONFIG_BCM63XX_CPU_6328 */ /* -@@ -703,6 +1265,18 @@ static const struct board_info __initcon +@@ -703,6 +1308,19 @@ static const struct board_info __initcon #endif /* CONFIG_BCM63XX_CPU_6318 */ #ifdef CONFIG_BCM63XX_CPU_6328 &board_96328avng, @@ -583,12 +626,13 @@ + &board_FAST2704V2, + &board_PDG_A4001N_A_000_1A1_AX, + &board_PDG_A4101N_A_000_1A1_AE, ++ &board_TG582N, + &board_TG582N_TELECOM_ITALIA, + &board_R5010UNV2, #endif /* CONFIG_BCM63XX_CPU_6328 */ #ifdef CONFIG_BCM63XX_CPU_6338 &board_96338gw, -@@ -742,7 +1316,21 @@ static struct of_device_id const bcm963x +@@ -742,7 +1360,22 @@ static struct of_device_id const bcm963x { .compatible = "sagem,fast-2704n", .data = &board_FAST2704N, }, #endif /* CONFIG_BCM63XX_CPU_6318 */ #ifdef CONFIG_BCM63XX_CPU_6328 @@ -606,6 +650,7 @@ + { .compatible = "sagem,fast-2704-v2", .data = &board_FAST2704V2, }, + { .compatible = "sercomm,ad1018", .data = &board_AD1018, }, + { .compatible = "sercomm,ad1018-nor", .data = &board_AD1018, }, ++ { .compatible = "technicolor,tg582n", .data = &board_TG582N, }, + { .compatible = "technicolor,tg582n-telecom-italia", .data = &board_TG582N_TELECOM_ITALIA, }, #endif /* CONFIG_BCM63XX_CPU_6328 */ #ifdef CONFIG_BCM63XX_CPU_6338 -- cgit v1.2.3