From d43b963b3d1172fbe7e3f57f88da11e4d7e54c95 Mon Sep 17 00:00:00 2001 From: Adrian Schmutzler Date: Sat, 15 Aug 2020 17:21:35 +0200 Subject: bcm63xx: reorganize board patches This renames board patches to make finding devices easier and reorders them based on their board. The devices are grouped based on the board/cpu_id. New device patches should be numbered based on their group. Signed-off-by: Adrian Schmutzler --- .../bcm63xx/patches-5.4/511-board_V2500V.patch | 93 ---------------------- 1 file changed, 93 deletions(-) delete mode 100644 target/linux/bcm63xx/patches-5.4/511-board_V2500V.patch (limited to 'target/linux/bcm63xx/patches-5.4/511-board_V2500V.patch') diff --git a/target/linux/bcm63xx/patches-5.4/511-board_V2500V.patch b/target/linux/bcm63xx/patches-5.4/511-board_V2500V.patch deleted file mode 100644 index e72c208cb3..0000000000 --- a/target/linux/bcm63xx/patches-5.4/511-board_V2500V.patch +++ /dev/null @@ -1,93 +0,0 @@ ---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c -+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c -@@ -429,6 +429,27 @@ static struct board_info __initdata boar - .force_duplex_full = 1, - }, - }; -+ -+static struct board_info __initdata board_V2500V_BB = { -+ .name = "V2500V_BB", -+ .expected_cpu_id = 0x6348, -+ -+ .has_pci = 1, -+ -+ .has_enet0 = 1, -+ .enet0 = { -+ .has_phy = 1, -+ .use_internal_phy = 1, -+ }, -+ -+ .has_enet1 = 1, -+ .enet1 = { -+ .has_phy = 1, -+ .phy_id = 0, -+ .force_speed_100 = 1, -+ .force_duplex_full = 1, -+ }, -+}; - #endif /* CONFIG_BCM63XX_CPU_6348 */ - - /* -@@ -693,6 +714,7 @@ static const struct board_info __initcon - &board_96348_D4PW, - &board_spw500v, - &board_96348sv, -+ &board_V2500V_BB, - #endif /* CONFIG_BCM63XX_CPU_6348 */ - #ifdef CONFIG_BCM63XX_CPU_6358 - &board_96358vw, -@@ -733,6 +755,7 @@ static struct of_device_id const bcm963x - { .compatible = "brcm,bcm96348gw-10", .data = &board_96348gw_10, }, - { .compatible = "brcm,bcm96348gw-11", .data = &board_96348gw_11, }, - { .compatible = "brcm,bcm96348gw-a", .data = &board_96348gw_a, }, -+ { .compatible = "bt,voyager-2500v-bb", .data = &board_V2500V_BB, }, - { .compatible = "d-link,dsl-2640b-b", .data = &board_96348_D4PW, }, - { .compatible = "davolink,dv-201amr", .data = &board_DV201AMR, }, - { .compatible = "dynalink,rta1025w", .data = &board_rta1025w_16, }, -@@ -794,6 +817,22 @@ void __init board_bcm963xx_init(void) - val &= MPI_CSBASE_BASE_MASK; - } - boot_addr = (u8 *)KSEG1ADDR(val); -+ pr_info("Boot address 0x%08x\n",(unsigned int)boot_addr); -+ -+ /* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */ -+ /* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/ -+ /* Loading firmware from the CFE Prompt always loads to Bank 0 */ -+ /* Do an early check of CFE and then select bank 0 */ -+ -+ if (boot_addr == (u8 *)0xbf800000) { -+ u8 *tmp_boot_addr = (u8*)0xbfc00000; -+ -+ bcm63xx_nvram_init(tmp_boot_addr + BCM963XX_NVRAM_OFFSET); -+ if (!strcmp(bcm63xx_nvram_get_name(), "V2500V_BB")) { -+ pr_info("V2500V: nvram bank 0\n"); -+ boot_addr = tmp_boot_addr; -+ } -+ } - - /* dump cfe version */ - cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET; ---- a/arch/mips/bcm63xx/dev-flash.c -+++ b/arch/mips/bcm63xx/dev-flash.c -@@ -21,6 +21,7 @@ - #include - #include - -+#include - #include - #include - #include -@@ -256,6 +257,13 @@ int __init bcm63xx_flash_register(void) - val = bcm_mpi_readl(MPI_CSBASE_REG(0)); - val &= MPI_CSBASE_BASE_MASK; - -+ /* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */ -+ /* Loading from CFE always uses Bank 0 */ -+ if (!strcmp(board_get_name(), "V2500V_BB")) { -+ pr_info("V2500V: Start in Bank 0\n"); -+ val = val + 0x400000; // Select Bank 0 start address -+ } -+ - mtd_resources[0].start = val; - mtd_resources[0].end = 0x1FFFFFFF; - } -- cgit v1.2.3