From 59c2f9eaad5688af523ff60d2f83d5d81447009b Mon Sep 17 00:00:00 2001 From: Daniele Castro Date: Thu, 10 Sep 2020 21:14:11 +0200 Subject: bcm63xx: add support for Technicolor TG582n MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Technicolor TG582n has a similar PCB as the OpenWrt's ADB P.DG A4001N1 with LEDs connected to different GPIO PINs in active low configuration. Hardware: * Board ID: DANT-1 * SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350 * RAM DDR2: 64 Mbyte - Winbond W9751G6KB-25 * Serial flash: 16 Mbyte - MXIC MX25L6445EMI * Ethernet: 4x Ethernet 10/100 baseT * Wifi 2.4GHz: Broadcom Corporation BCM43227 Wireless Network Adapter (rev 30) * LEDs: 2x Power, 1x Ethernet, 1x Broadband, 2x Wi-Fi, 2x WPS, 4x ethernet * Buttons: 1x Reset, 1x WPS, 1x WiFi * UART: 1x TTL 115200n8, VCC GND TX RX, on J3 connector (short R62 and R63) Installation via CFE: * Stock CFE has to be overwritten with a generic 6328 one that can upload .bin images with no signature check (cfe6328_configured.bin) * Connect a serial port to the board * Stop the CFE boot process after power on by pressing enter * Set static IP 192.168.2.10 and subnet mask 255.255.255.0 * Navigate to http://192.168.2.50/ * Upload the OpenWrt image file PCB: |GPIO: |TG582n: LED2R |488(08) |red Power LED2G |484(04) |green Power LED10R |486(06) | LED13G |485(05) |green Ethernet LED11R |494(14) | LED14G |491(11) |green Broadband LED5R |487(07) |red Internet LED5G |481(01) |green Internet LED12R |498(18) | LED12G |499(19) | LED6R |482(02) |red Wi-Fi LED6G |483(03) |green Wi-Fi LED7R |490(10) |red WPS LED7G |489(09) |green WPS LED4 |508(28) |ethernet port 4 LED3 |507(27) |ethernet port 3 LED9 |506(26) |ethernet port 2 LED8 |505(25) |ethernet port 1 SW3 |503(23) |key Reset SW5 |504(24) |key WPS SW4 |495(15) |key Wi-Fi SW6 |493(13) | SW1 |492(12) | Signed-off-by: Daniele Castro [Fix base-files, refresh patch] Signed-off-by: Álvaro Fernández Rojas --- target/linux/bcm63xx/base-files/etc/board.d/01_leds | 4 ++++ target/linux/bcm63xx/base-files/etc/board.d/02_network | 1 + target/linux/bcm63xx/base-files/etc/uci-defaults/09_fix_crc | 1 + 3 files changed, 6 insertions(+) (limited to 'target/linux/bcm63xx/base-files') diff --git a/target/linux/bcm63xx/base-files/etc/board.d/01_leds b/target/linux/bcm63xx/base-files/etc/board.d/01_leds index 5a2a933b0c..299bb117e9 100755 --- a/target/linux/bcm63xx/base-files/etc/board.d/01_leds +++ b/target/linux/bcm63xx/base-files/etc/board.d/01_leds @@ -94,6 +94,10 @@ sercomm,h500-s-lowi|\ sercomm,h500-s-vfes) ucidef_set_led_netdev "wan" "WAN" "green:internet" "eth0.2" ;; +technicolor,tg582n) + ucidef_set_led_netdev "wlan0" "WIFI" "green:wifi" "wlan0" + ucidef_set_led_usbdev "usb" "USB" "red:power" "1-1" + ;; technicolor,tg582n-telecom-italia) ucidef_set_led_netdev "wlan0" "WIFI" "green:wifi" "wlan0" ucidef_set_led_usbdev "usb1" "USB1" "green:service" "1-1" diff --git a/target/linux/bcm63xx/base-files/etc/board.d/02_network b/target/linux/bcm63xx/base-files/etc/board.d/02_network index 9c9047b2fb..700439ec36 100755 --- a/target/linux/bcm63xx/base-files/etc/board.d/02_network +++ b/target/linux/bcm63xx/base-files/etc/board.d/02_network @@ -39,6 +39,7 @@ huawei,echolife-hg655b|\ nucom,r5010un-v2|\ sagem,fast-2504n|\ sagem,fast-2704-v2|\ +technicolor,tg582n|\ technicolor,tg582n-telecom-italia|\ zyxel,p870hw-51a-v2) ucidef_add_switch "switch0" \ diff --git a/target/linux/bcm63xx/base-files/etc/uci-defaults/09_fix_crc b/target/linux/bcm63xx/base-files/etc/uci-defaults/09_fix_crc index 9b94a23eaf..a176eb1735 100644 --- a/target/linux/bcm63xx/base-files/etc/uci-defaults/09_fix_crc +++ b/target/linux/bcm63xx/base-files/etc/uci-defaults/09_fix_crc @@ -34,6 +34,7 @@ case "$(board_name)" in nucom,r5010un-v2|\ observa,vh4032n|\ t-com,speedport-w-303v|\ + technicolor,tg582n|\ technicolor,tg582n-telecom-italia|\ telsey,cpva502plus|\ telsey,cpva642|\ -- cgit v1.2.3