From a4c0c031b8c51daf52ba2947ce139b37bae47086 Mon Sep 17 00:00:00 2001 From: Sven Eckelmann Date: Mon, 23 Nov 2020 13:41:34 +0100 Subject: ath79: Add support for OpenMesh OM5P-AC v2 Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/200 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi (11n) * 2T2R 5 GHz Wi-Fi (11ac) * 4x GPIO-LEDs (3x wifi, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + AR8031 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas This device support is based on the partially working stub from commit 53c474abbdfe ("ath79: add new OF only target for QCA MIPS silicon"). Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 .bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp .bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/.bin Signed-off-by: Sven Eckelmann (cherry picked from commit 1699c1dc7f26b332f868d338457abfbe716d6ba0) --- .../generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | 7 ++----- target/linux/ath79/generic/base-files/lib/upgrade/platform.sh | 3 ++- 2 files changed, 4 insertions(+), 6 deletions(-) (limited to 'target/linux/ath79/generic/base-files') diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 14103a7310..69735f3360 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -100,12 +100,9 @@ case "$FIRMWARE" in ath10k_patch_mac $(mtd_get_mac_binary art 0xc) ;; openmesh,mr1750-v1|\ - openmesh,mr1750-v2) - caldata_extract "ART" 0x5000 0x844 - ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16) - ;; + openmesh,mr1750-v2|\ openmesh,om5p-ac-v2) - caldata_extract "art" 0x5000 0x844 + caldata_extract "ART" 0x5000 0x844 ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16) ;; qihoo,c301) diff --git a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh index f8b1c13677..1240ef51e8 100644 --- a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh +++ b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh @@ -78,7 +78,8 @@ platform_do_upgrade() { openmesh,om2p-hs-v3|\ openmesh,om2p-hs-v4|\ openmesh,om2p-lc|\ - openmesh,om5p) + openmesh,om5p|\ + openmesh,om5p-ac-v2) PART_NAME="inactive" platform_do_upgrade_openmesh "$1" ;; -- cgit v1.2.3