From 72ef5945508193228544bcd7fcfe81b32e8dc042 Mon Sep 17 00:00:00 2001 From: Sven Eckelmann Date: Mon, 23 Nov 2020 13:41:34 +0100 Subject: ath79: Add support for OpenMesh OM5P-AN Device specifications: ====================== * Qualcomm/Atheros AR9344 rev 2 * 560/450/225 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 1T1R 2.4 GHz Wi-Fi * 2T2R 5 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + 10/100 Mbps Ethernet + builtin switch port 1 + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 .bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp .bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/.bin Signed-off-by: Sven Eckelmann --- target/linux/ath79/generic/base-files/etc/board.d/01_leds | 4 ++++ .../ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom | 3 ++- target/linux/ath79/generic/base-files/lib/upgrade/platform.sh | 3 ++- 3 files changed, 8 insertions(+), 2 deletions(-) (limited to 'target/linux/ath79/generic/base-files') diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index 7b27dd8910..14b38b4e66 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -271,6 +271,10 @@ openmesh,om2p-hs-v4) ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth0" ucidef_set_led_switch "lan" "LAN" "blue:lan" "switch0" "0x02" ;; +openmesh,om5p-an) + ucidef_set_led_netdev "lan" "LAN" "blue:lan" "eth0" + ucidef_set_led_switch "wan" "WAN" "blue:wan" "switch0" "0x02" + ;; pcs,cr3000) ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth1" ucidef_set_led_switch "lan1" "LAN1" "blue:lan1" "switch0" "0x04" diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom index 89a6adf5a6..10421c2e28 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom @@ -127,7 +127,8 @@ case "$FIRMWARE" in caldata_extract "art" 0x1000 0x1000 ;; openmesh,mr600-v1|\ - openmesh,mr600-v2) + openmesh,mr600-v2|\ + openmesh,om5p-an) caldata_extract "ART" 0x5000 0x440 ;; wd,mynet-n600|\ diff --git a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh index 20041e4c95..b7e2930129 100644 --- a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh +++ b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh @@ -80,7 +80,8 @@ platform_do_upgrade() { openmesh,om2p-hs-v3|\ openmesh,om2p-hs-v4|\ openmesh,om2p-lc|\ - openmesh,om5p) + openmesh,om5p|\ + openmesh,om5p-an) PART_NAME="inactive" platform_do_upgrade_openmesh "$1" ;; -- cgit v1.2.3