From 5b37b52e69884c6c843738cc45ed8a1deba0eba3 Mon Sep 17 00:00:00 2001 From: Sven Eckelmann Date: Mon, 23 Nov 2020 13:41:34 +0100 Subject: ath79: Add support for OpenMesh OM2P-HS v4 Device specifications: ====================== * Qualcomm/Atheros QCA9533 v2 * 650/600/217 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2x 10/100 Mbps Ethernet * 2T2R 2.4 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x fast ethernet - eth0 + 24V passive POE (mode B) + used as WAN interface - eth1 + 802.3af POE + builtin switch port 1 + used as LAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 .bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp .bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/.bin Signed-off-by: Sven Eckelmann --- target/linux/ath79/generic/base-files/etc/board.d/01_leds | 3 ++- target/linux/ath79/generic/base-files/etc/board.d/02_network | 1 + 2 files changed, 3 insertions(+), 1 deletion(-) (limited to 'target/linux/ath79/generic/base-files/etc') diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index 8095712e88..5795e2a0ae 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -230,7 +230,8 @@ netgear,wnr2200-16m) ucidef_set_led_switch "lan3amber" "LAN3 (amber)" "amber:lan3" "switch0" "0x08" "0x02" ucidef_set_led_switch "lan4amber" "LAN4 (amber)" "amber:lan4" "switch0" "0x10" "0x02" ;; -openmesh,om2p-v4) +openmesh,om2p-v4|\ +openmesh,om2p-hs-v4) ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth0" ucidef_set_led_switch "lan" "LAN" "blue:lan" "switch0" "0x02" ;; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index fa98b18e59..f78fdeea9c 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -153,6 +153,7 @@ ath79_setup_interfaces() comfast,cf-e314n-v2|\ compex,wpj531-16m|\ openmesh,om2p-v4|\ + openmesh,om2p-hs-v4|\ plasmacloud,pa300|\ plasmacloud,pa300e|\ tplink,cpe210-v1|\ -- cgit v1.2.3