From 213250b56bb4a3043dcb5a48e2f849b9e45967d7 Mon Sep 17 00:00:00 2001 From: Davide Fioravanti Date: Sun, 19 Jan 2020 21:05:31 +0100 Subject: ath79: add support for TP-Link Archer D7/D7b v1 TP-Link Archer D7 v1 is a dual-band AC1750 router + modem. The router section is based on Qualcomm/Atheros QCA9558 + QCA9880. The "DSL" section is based on BCM6318 but it's currently not supported. The Archer D7b seems to differ from the Archer D7 only in the partition table. Router section - Specification: 775/650/258 MHz (CPU/DDR/AHB) 128 MB of RAM (DDR2) 16 MB of FLASH (SPI NOR) 3T3R 2.4 GHz 3T3R 5 GHz 4x 10/100/1000 Mbps Ethernet 7x LED, 2x button UART header on PCB Known issues: - Broadband LED (missing GPIO - probably driven by the BCM6318) - Internet LED (missing GPIO - probably driven by the BCM6318) - WIFI LED (working only for one interface at a time, while in the OEM firmware works for both wifi interfaces; thus, this patch does not set a trigger by default) - DSL not working (eth0) UART connection --------------- J1 HEADER (Qualcomm CPU) . VCC . GND . RX O TX J41 HEADER (Broadcom CPU) . VCC . GND . RX O TX The following instructions require a connection to the J1 UART header and are tested for the Archer D7 v1. For the Archer D7b v1, names should be changed accordingly. Flash instructions under U-Boot, using UART ------------------------------------------ 1. Press "tpl" to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d7-v1-squashfs-sysupgrade.bin erase 0x9f020000 +f90000 cp.b 0x81000000 0x9f020000 0xf90000 reset Initramfs instructions under U-Boot for testing, using UART ---------------------------------------------------------- 1. Press "tpl" to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d7-v1-initramfs-kernel.bin bootm 0x81000000 4. Here you can backup the original firmware and/or flash the sysupgrade openwrt if you want Restore the original firmware ----------------------------- 0. Backup every partition using the OpenWrt web interface 1. Download the OEM firmware from the TP-Link website 2. Extract the bin file in a folder (eg. Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin) 3. Remove the U-Boot and the Broadcom image part from the file. Issue the following command: dd if="Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin" of="Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin.mod" skip=257 bs=512 count=31872 4. Double check the .mod file size. It must be 16318464 bytes. 5. Flash it using the OpenWrt web interface. Force the update if needed. WARNING: Remember to NOT keep settings. 5b. (Alternative to 5.) Flash it using the U-Boot and UART connection. Issue below commands in the U-Boot: tftpboot 0x81000000 Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin.mod erase 0x9f020000 +f90000 cp.b 0x81000000 0x9f020000 0xf90000 reset Signed-off-by: Davide Fioravanti [cosmetic DTS changes, remove TPLINK_HWREVADD := 0, do not use two phyXtpt at once, add missing buttons, minor commit message adjustments] Signed-off-by: Adrian Schmutzler --- .../generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'target/linux/ath79/generic/base-files/etc/hotplug.d') diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 43c2f9ced5..d354c7eaec 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -99,6 +99,11 @@ case "$FIRMWARE" in caldata_extract "art" 0x5000 0x844 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary romfile 0xf100) +2) ;; + tplink,archer-d7-v1|\ + tplink,archer-d7b-v1) + caldata_extract "art" 0x5000 0x844 + ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary romfs 0xf100) +2) + ;; tplink,re350k-v1) caldata_extract "art" 0x5000 0x844 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary config 0x10008) +2) -- cgit v1.2.3