From 97f561725962ddb8823b2e01563a0f37f7930477 Mon Sep 17 00:00:00 2001 From: Sven Eckelmann Date: Mon, 23 Nov 2020 13:41:34 +0100 Subject: ath79: Add support for OpenMesh OM5P-AC v1 Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/240 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi (11n) * 2T2R 5 GHz Wi-Fi (11ac) * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + AR8035 ethernet PHY (SGMII) + 10/100/1000 Mbps Ethernet + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 .bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp .bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/.bin Signed-off-by: Sven Eckelmann --- .../ath79/dts/qca9558_openmesh_om5p-ac-v1.dts | 216 +++++++++++++++++++++ 1 file changed, 216 insertions(+) create mode 100644 target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v1.dts (limited to 'target/linux/ath79/dts') diff --git a/target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v1.dts b/target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v1.dts new file mode 100644 index 0000000000..de21f0119f --- /dev/null +++ b/target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v1.dts @@ -0,0 +1,216 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca955x.dtsi" + +#include +#include + +/ { + compatible = "openmesh,om5p-ac-v1", "qca,qca9558"; + model = "OpenMesh OM5P-AC v1"; + + chosen { + /delete-property/ bootargs; + }; + + aliases { + serial0 = &uart; + led-boot = &led_power_blue; + led-failsafe = &led_power_blue; + led-running = &led_power_blue; + led-upgrade = &led_power_blue; + label-mac-device = ð0; + }; + + leds { + compatible = "gpio-leds"; + + led_power_blue: power_blue { + label = "blue:power"; + gpios = <&gpio 18 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + wan_blue { + label = "blue:wan"; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + }; + + lan_blue { + label = "blue:lan"; + gpios = <&gpio 20 GPIO_ACTIVE_LOW>; + }; + + wifi_green { + label = "green:wifi"; + gpios = <&gpio 21 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + wifi_yellow { + label = "yellow:wifi"; + gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + }; + + wifi_red { + label = "red:wifi"; + gpios = <&gpio 23 GPIO_ACTIVE_LOW>; + }; + }; + + i2c { + compatible = "i2c-gpio"; + gpios = <&gpio 11 GPIO_ACTIVE_HIGH /* sda */ + &gpio 12 GPIO_ACTIVE_HIGH /* scl */ + >; + #address-cells = <1>; + #size-cells = <0>; + + i2c-gpio,scl-open-drain; + i2c-gpio,sda-open-drain; + + tmp423a@4c { + compatible = "ti,tmp423"; + reg = <0x4c>; + }; + }; + + watchdog { + compatible = "linux,wdt-gpio"; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + hw_algo = "toggle"; + /* hw_margin_ms is actually 300s but driver limits it to 60s */ + hw_margin_ms = <60000>; + always-running; + }; +}; + +&spi { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <40000000>; + + /* partitions are passed via bootloader */ + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x040000>; + read-only; + }; + + partition@40000 { + label = "u-boot-env"; + reg = <0x040000 0x010000>; + }; + + partition@50000 { + label = "custom"; + reg = <0x050000 0x060000>; + read-only; + }; + + partition@b0000 { + label = "inactive"; + reg = <0x0b0000 0x7a0000>; + }; + + partition@850000 { + label = "inactive2"; + reg = <0x850000 0x7a0000>; + }; + + art: partition@ff0000 { + label = "ART"; + reg = <0xff0000 0x010000>; + read-only; + }; + }; + }; +}; + +&mdio0 { + status = "okay"; + + phy-mask = <0x6>; + + phy1: ethernet-phy@1 { + reg = <1>; + eee-broken-100tx; + eee-broken-1000t; + }; + + phy2: ethernet-phy@2 { + reg = <2>; + eee-broken-100tx; + eee-broken-1000t; + at803x-override-sgmii-link-check; + }; +}; + +ð0 { + status = "okay"; + + pll-data = <0x82000101 0x80000101 0x80001313>; + + nvmem-cells = <&macaddr_art_0>; + nvmem-cell-names = "mac-address"; + + phy-mode = "rgmii-id"; + phy-handle = <&phy1>; + + gmac-config { + device = <&gmac>; + rgmii-enabled = <1>; + rxd-delay = <3>; + rxdv-delay = <3>; + txd-delay = <0>; + txen-delay = <0>; + }; +}; + +ð1 { + status = "okay"; + + pll-data = <0x03000101 0x80000101 0x80001313>; + + nvmem-cells = <&macaddr_art_6>; + nvmem-cell-names = "mac-address"; + + qca955x-sgmii-fixup; + + phy-handle = <&phy2>; +}; + +&wmac { + status = "okay"; + + mtd-cal-data = <&art 0x1000>; + nvmem-cells = <&macaddr_art_0>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <2>; +}; + +&pcie1 { + status = "okay"; +}; + +&art { + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_art_0: macaddr@0 { + reg = <0x0 0x6>; + }; + + macaddr_art_6: macaddr@6 { + reg = <0x6 0x6>; + }; +}; -- cgit v1.2.3