From 796ad2f7ef6fefcf821a3b21cadfdb7ef3126e95 Mon Sep 17 00:00:00 2001 From: Perry Melange Date: Wed, 7 Aug 2019 19:25:13 +0200 Subject: ath79: add support for D-Link DIR-842 C3 Hardware spec of DIR-842 C3: SoC: QCA9563 DRAM: 128MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337N WiFi 5.8GHz: QCA9888 WiFi 2.4Ghz: QCA9563 USB: circuit onboard, but components are not soldered Flash instructions: 1. Upgrade the factory.bin through the factory web interface or the u-boot failsafe interface. The firmware will boot up correctly for the first time. Do not power off the device after OpenWrt has booted. Otherwise the u-boot will enter failsafe mode as the checksum of the firmware has been changed. 2. Upgrade the sysupgrade.bin in OpenWrt. After upgrading completes the u-boot won't complain about the firmware checksum and it's OK to use now. 3. If you powered off the device before upgrading the sysupgrade.bin, just upgrade the factory.bin through the u-boot failsafe interface and then goto step 2. Signed-off-by: Perry Melange --- target/linux/ath79/base-files/etc/board.d/01_leds | 1 + target/linux/ath79/base-files/etc/board.d/02_network | 2 ++ target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom | 1 + target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | 1 + 4 files changed, 5 insertions(+) (limited to 'target/linux/ath79/base-files') diff --git a/target/linux/ath79/base-files/etc/board.d/01_leds b/target/linux/ath79/base-files/etc/board.d/01_leds index 35cb74db28..aad41b0dad 100755 --- a/target/linux/ath79/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/base-files/etc/board.d/01_leds @@ -64,6 +64,7 @@ comfast,cf-e5) ;; dlink,dir-842-c1|\ dlink,dir-842-c2|\ +dlink,dir-842-c3|\ dlink,dir-859-a1) ucidef_set_led_switch "internet" "WAN" "$boardname:green:internet" "switch0" "0x20" ;; diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index 9c6429984f..e3c1f423f1 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -123,6 +123,7 @@ ath79_setup_interfaces() dlink,dir-835-a1|\ dlink,dir-842-c1|\ dlink,dir-842-c2|\ + dlink,dir-842-c3|\ dlink,dir-859-a1|\ engenius,epg5000|\ tplink,archer-c2-v3|\ @@ -316,6 +317,7 @@ ath79_setup_macs() ;; dlink,dir-842-c1|\ dlink,dir-842-c2|\ + dlink,dir-842-c3|\ dlink,dir-859-a1|\ nec,wg1200cr|\ wd,mynet-n750) diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom index a7d482580b..62d53248bc 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom @@ -107,6 +107,7 @@ case "$FIRMWARE" in ;; dlink,dir-842-c1|\ dlink,dir-842-c2|\ + dlink,dir-842-c3|\ dlink,dir-859-a1|\ nec,wg1200cr|\ wd,mynet-n750) diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index f6e2b801cb..501053e9d7 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -191,6 +191,7 @@ case "$FIRMWARE" in case $board in dlink,dir-842-c1|\ dlink,dir-842-c2|\ + dlink,dir-842-c3|\ nec,wg1200cr) ath10kcal_extract "art" 20480 12064 ath10kcal_patch_mac_crc $(mtd_get_mac_ascii devdata wlan5mac) -- cgit v1.2.3