From 1724d4e9ed7716a5444eca42adf045c2f3afc554 Mon Sep 17 00:00:00 2001 From: David Bauer Date: Thu, 27 Dec 2018 02:32:38 +0100 Subject: ath79: add support for devolo WiFi pro 1200e Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) 1x Atheros AR8033 WiFi2: QCA9558 2T2R WiFi5: QCA9880 2T2R BTN: 1x Reset LED: 1x LED blue 1x LED red BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to reset-button Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/ Signed-off-by: David Bauer --- target/linux/ath79/base-files/etc/board.d/02_network | 3 +++ .../linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | 4 ++++ 2 files changed, 7 insertions(+) (limited to 'target/linux/ath79/base-files') diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index 5e1df97a87..b2c7762bb5 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -58,6 +58,9 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "0@eth0" "1:lan:1" "3:lan:4" "4:lan:3" "5:lan:2" "2:wan" ;; + devolo,dvl1200e) + ucidef_set_interface_lan "eth0 eth1" + ;; dlink,dir-825-b1) ucidef_set_interface_wan "eth1" ucidef_add_switch "switch0" \ diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index da39fd7195..deaac72174 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -87,6 +87,10 @@ board=$(board_name) case "$FIRMWARE" in "ath10k/cal-pci-0000:00:00.0.bin") case $board in + devolo,dvl1200e) + ath10kcal_extract "art" 20480 2116 + ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary art 0) -1) + ;; glinet,gl-x750) ath10kcal_extract "art" 20480 2116 ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1) -- cgit v1.2.3