From 8a4dc6f48c0a4503b655195846ae1bff9a691a40 Mon Sep 17 00:00:00 2001 From: Christian Mauderer Date: Fri, 15 Mar 2019 21:02:54 +0100 Subject: ath79: add support for Ubiquiti airCube ISP MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The Ubiquiti Network airCube ISP is a cube shaped 2.4 GHz with internal 2x2 MIMO antennas. It can be supplied via a USB connector or via PoE. There are for 10/100 Mbps ports (1 * WAN + 3 * LAN). There is an optional PoE passthrough from the first LAN port to the WAN port. SoC: Qualcomm / Atheros QCA9533-BL3A RAM: 64 MB DDR2 Flash: 16 MB SPI NOR Ethernet: 4x 10/100 Mbps (1 WAN + 3 LAN) LEDS: 1x via a SPI controller (not yet supported) Buttons: 1x Reset Serial: 1x (only RX and TX); 115200 baud, 8N1 Missing points: - LED not yet supported - Factory upgrade via web IF or TFTP recovery not yet supported (Needs RSA signed images, for details see PR#1958) The serial port is on a four pin connextor labeled J1 and located between Ethernet and USB connector. The pinout is: 1. 3V3 (out) 2. Rx (in) 3. Tx (out) 4. GND Upgrading via serial port / U-Boot: - Connect the serial port via a level converter - Power the system and stop U-Boot with pressing any key when `Hit any key to stop autoboot` is displayed. Note: Pressing space multiple times untill U-Boot reaches that location works well. - Connect a PC with the IP 192.168.1.100 (or some other in that net) running a TFTP-Server to one of the LAN ports. Copy the sysupgrade image to the server. - Set the U-Boot server IP with setenv serverip 192.168.1.100 - Load the flash image to RAM with tftpboot 0x81000000 sysupgrade.bin - Erase the flash with erase 0x9f050000 0x9ffaffff - Write the new flash content with cp 0x81000000 0x9f050000 ${filesize} - Reset the device with reset Signed-off-by: Christian Mauderer [removed full stop in subject and added lockdown note to commit message] Signed-off-by: Petr Štetiar --- target/linux/ath79/base-files/etc/board.d/02_network | 5 +++++ target/linux/ath79/base-files/etc/board.d/03_gpio_switches | 3 +++ 2 files changed, 8 insertions(+) (limited to 'target/linux/ath79/base-files/etc/board.d') diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index e399210b2b..4651669d31 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -233,6 +233,11 @@ ath79_setup_interfaces() tplink,tl-wr941-v2) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan" ;; + ubnt,acb-isp) + ucidef_set_interface_wan "eth0" + ucidef_add_switch "switch0" \ + "0@eth1" "2:lan:1" "3:lan:3" "4:lan:2" + ;; ubnt,routerstation-pro) ucidef_set_interface_wan "eth0" ucidef_add_switch "switch0" \ diff --git a/target/linux/ath79/base-files/etc/board.d/03_gpio_switches b/target/linux/ath79/base-files/etc/board.d/03_gpio_switches index c852b77d79..6a51a79790 100755 --- a/target/linux/ath79/base-files/etc/board.d/03_gpio_switches +++ b/target/linux/ath79/base-files/etc/board.d/03_gpio_switches @@ -26,6 +26,9 @@ librerouter,librerouter-v1) ubnt,nanostation-ac) ucidef_add_gpio_switch "poe_passthrough" "PoE Passthrough" "3" ;; +ubnt,acb-isp) + ucidef_add_gpio_switch "poe_passthrough" "PoE Passthrough" "11" + ;; esac board_config_flush -- cgit v1.2.3