From bc18c2bfe7a80630eea15aa71800b0829ce32634 Mon Sep 17 00:00:00 2001 From: Daniel Gimpelevich Date: Fri, 31 Aug 2018 19:28:35 -0700 Subject: ath79: add support for Bluesocket BSAP1880 board MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This board was used in dual-band 802.11n enterprise access points, models BSAP-1800v2 and BSAP-1840, introduced in 2010 by Bluesocket, which was acquired by Adtran in 2011, who has now EOL'ed them. They differed only in that the BSAP-1840's antennae were detachable, while the BSAP-1800v2's were inside the case. They have an external RJ-45 console port, which works with standard Cisco 72-3383-01 console cables. Specification: - System-On-Chip: AR7161 - CPU/Speed: 600 MHz - Flash-Chip: Macronix MX25L12845E - Flash size: 16 MiB - RAM: 64 MiB - Wireless No1: Lite-On WN2601A card: AR9160/AR9103 2.4GHz 802.11bgn - Wireless No2: Lite-On WN2502A card: AR9160/AR9106 5GHz 802.11an - PHY: Vitesse VSC8601, Rev. B Installation: 1. Connect to the serial console using a terminal that supports YMODEM at 115200 bps, 8 data bits, no parity, 1 stop bit 2. Interrupt the bootloader using its password, which is: r00t 3. Issue the "fis init" command, confirming if prompted 4. Look at the length of the openwrt-ath79-generic-*-squashfs-kernel.bin file, and substitute it below, instead of where I have "LeNgTh" 5. Issue the following command, and upload this file using YMODEM protocol load -r -v -b 0x80060000 -m ymodem 6. Issue the following commands, substituting as mentioned above: fis create -b 0x80060000 -l LeNgTh vmlinux_2 load -r -v -b 0x80100000 -m ymodem 7. Using YMODEM, upload openwrt-ath79-generic-*-squashfs-rootfs.bin 8. Issue the "fis free" command, and for the first range in its response, use a hexadecimal calculator to subtract the start from the end in order to substitute it below, with the leading "0x" to specify it in hexadecimal, instead of where I have "LeNgTh" 9. Issue the following commands, substituting as mentioned above: fis create -b 0x80100000 -l LeNgTh -e 0 -r 0 rootfs reset 10.Wait for the status LED to go solid green Tested-by: Brian Gonyer Signed-off-by: Daniel Gimpelevich [fixed obsolete $ARGV in platform_do_upgrade] Signed-off-by: Petr Štetiar --- target/linux/ath79/base-files/etc/board.d/02_network | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'target/linux/ath79/base-files/etc/board.d/02_network') diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index f7cac3e300..56650c3f6b 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -9,6 +9,8 @@ ath79_setup_interfaces() local board="$1" case "$board" in + adtran,bsap1800-v2|\ + adtran,bsap1840|\ aruba,ap-105|\ avm,fritz300e|\ devolo,dvl1200i|\ @@ -269,6 +271,11 @@ ath79_setup_macs() local board="$1" case "$board" in + adtran,bsap1800-v2|\ + adtran,bsap1840) + fconfig -s -w -d $(find_mtd_part "RedBoot config") -n boot_cntb -x 0 + lan_mac=$(mtd_get_mac_binary "Board data" 2) + ;; avm,fritz300e) lan_mac=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)")) ;; -- cgit v1.2.3