From 6165e4aab0e22b780b6b1dde887ed803a7c8210a Mon Sep 17 00:00:00 2001 From: Piotr Dymacz Date: Sun, 2 Jul 2017 18:32:38 +0200 Subject: ar71xx: add support for TP-Link TL-WR902AC v1 TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of TL-MR3020 (both devices use very similar enclosure, in same size). New device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC. Specification: - 650/391/216 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 1x USB 2.0 (GPIO-controlled power) - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz (QCA9531) - 1T1R 5 GHz (QCA9887) - 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch - UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper resitors are missing on TX/RX lines) - 1x micro USB (for power only) Flash instructions: Use "factory" image under vendor GUI. Recovery instructions: This device contains tftp recovery mode inside U-Boot. You can use it to flash LEDE (use "factory" image) or vendor firmware. 1. Configure PC with static IP 192.168.0.66/24 and tftp server. 2. Rename "lede-ar71xx-generic-tl-wr902ac-v1-squashfs-factory.bin" to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir. 3. Connect PC with LAN port, press the reset button, power up the router and keep button pressed until WPS LED lights up. 4. Router will download file from server, write it to flash and reboot. Root access over serial line in vendor firmware: root/sohoadmin. Signed-off-by: Piotr Dymacz --- target/linux/ar71xx/image/tp-link.mk | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) (limited to 'target/linux/ar71xx/image') diff --git a/target/linux/ar71xx/image/tp-link.mk b/target/linux/ar71xx/image/tp-link.mk index 8d6eb616f2..8422a1b2dd 100644 --- a/target/linux/ar71xx/image/tp-link.mk +++ b/target/linux/ar71xx/image/tp-link.mk @@ -1026,6 +1026,25 @@ define Device/tl-wr847n-v8 endef TARGET_DEVICES += tl-wr842n-v1 tl-wr842n-v2 tl-wr842n-v3 tl-wr843nd-v1 tl-wr847n-v8 +define Device/tl-wr902ac-v1 + DEVICE_TITLE := TP-LINK TL-WR902AC v1 + DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport \ + kmod-ath10k ath10k-firmware-qca9887 -swconfig -uboot-envtools + BOARDNAME := TL-WR902AC-V1 + DEVICE_PROFILE := TLWR902 + TPLINK_BOARD_ID := TL-WR902AC-V1 + TPLINK_HWID := 0x0 + SUPPORTED_DEVICES := tl-wr902ac-v1 + IMAGE_SIZE := 7360k + KERNEL := kernel-bin | patch-cmdline | lzma | mktplinkfw-kernel + IMAGES += factory.bin + IMAGE/factory.bin := append-rootfs | tplink-safeloader factory + IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade | \ + append-metadata | check-size $$$$(IMAGE_SIZE) + MTDPARTS := spi0.0:128k(u-boot)ro,7360k(firmware),640k(tplink)ro,64k(art)ro +endef +TARGET_DEVICES += tl-wr902ac-v1 + define Device/tl-wr940n-v4 $(Device/tplink-4mlzma) DEVICE_TITLE := TP-LINK TL-WR940N v4 -- cgit v1.2.3