From b74f63f81d6121b5eace3f0c0c87399f7e0fde92 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?=E5=BC=A0=E9=B9=8F?= Date: Tue, 17 Jul 2018 18:08:10 +0800 Subject: ar71xx:add support for E558 v2 MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Qxwlan E558 v2 is based on Qualcomm QCA9558 + AR8327. Specification: - 720/600/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 8/16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz (QCA9558) - 3x 10/100/1000 Mbps Ethernet (one port with PoE support) - 4x miniPCIe slot (USB 2.0 bus only) - 1x microSIM slot - 5x LED (4 driven by GPIO) - 1x button (reset) - 1x 3-pos switch - 1x DC jack for main power input (9-48 V) - UART (JP5) and LEDs (J8) headers on PCB Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Signed-off-by: 张鹏 --- .../ar71xx/files/arch/mips/ath79/Kconfig.openwrt | 11 ++ target/linux/ar71xx/files/arch/mips/ath79/Makefile | 1 + .../ar71xx/files/arch/mips/ath79/mach-e558-v2.c | 170 +++++++++++++++++++++ .../linux/ar71xx/files/arch/mips/ath79/machtypes.h | 1 + 4 files changed, 183 insertions(+) create mode 100644 target/linux/ar71xx/files/arch/mips/ath79/mach-e558-v2.c (limited to 'target/linux/ar71xx/files/arch') diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt index 4ae6e6dcc8..3cd90a446b 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt +++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt @@ -711,6 +711,17 @@ config ATH79_MACH_E2100L select ATH79_DEV_WMAC select ATH79_NVRAM +config ATH79_MACH_E558_V2 + bool "Qxwlan E558 v2 support" + select SOC_QCA955X + select ATH79_DEV_AP9X_PCI if PCI + select ATH79_DEV_ETH + select ATH79_DEV_GPIO_BUTTONS + select ATH79_DEV_LEDS_GPIO + select ATH79_DEV_M25P80 + select ATH79_DEV_USB + select ATH79_DEV_WMAC + config ATH79_MACH_E600G_V2 bool "Qxwlan E600G/E600GAC v2 support" select SOC_QCA953X diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile b/target/linux/ar71xx/files/arch/mips/ath79/Makefile index 996fd4c68a..690738e1e6 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile +++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile @@ -112,6 +112,7 @@ obj-$(CONFIG_ATH79_MACH_DR344) += mach-dr344.o obj-$(CONFIG_ATH79_MACH_DR531) += mach-dr531.o obj-$(CONFIG_ATH79_MACH_DRAGINO2) += mach-dragino2.o obj-$(CONFIG_ATH79_MACH_E1700AC_V2) += mach-e1700ac-v2.o +obj-$(CONFIG_ATH79_MACH_E558_V2) += mach-e558-v2.o obj-$(CONFIG_ATH79_MACH_E600G_V2) += mach-e600g-v2.o obj-$(CONFIG_ATH79_MACH_EAP120) += mach-eap120.o obj-$(CONFIG_ATH79_MACH_EAP300V2) += mach-eap300v2.o diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-e558-v2.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-e558-v2.c new file mode 100644 index 0000000000..c067d58bbb --- /dev/null +++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-e558-v2.c @@ -0,0 +1,170 @@ +/* + * Qxwlan E558 v2 board support + * + * Copyright (C) 2017 Peng Zhang + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published + * by the Free Software Foundation. + */ + +#include +#include +#include +#include +#include + +#include + +#include "common.h" +#include "dev-ap9x-pci.h" +#include "dev-eth.h" +#include "dev-gpio-buttons.h" +#include "dev-leds-gpio.h" +#include "dev-m25p80.h" +#include "dev-spi.h" +#include "dev-usb.h" +#include "dev-wmac.h" +#include "machtypes.h" +#include "pci.h" + +#define E558_V2_GPIO_LED_WLAN 13 +#define E558_V2_GPIO_LED_SYSTEM 14 +#define E558_V2_GPIO_LED_QSS 15 + +#define E558_V2_GPIO_BTN_RESET 16 + +#define E558_V2_KEYS_POLL_INTERVAL 20 /* msecs */ +#define E558_V2_KEYS_DEBOUNCE_INTERVAL (3 * E558_V2_KEYS_POLL_INTERVAL) + +static struct gpio_led e558_v2_leds_gpio[] __initdata = { + { + .name = "e558-v2:green:qss", + .gpio = E558_V2_GPIO_LED_QSS, + .active_low = 1, + }, + { + .name = "e558-v2:green:system", + .gpio = E558_V2_GPIO_LED_SYSTEM, + .active_low = 1, + }, + { + .name = "e558-v2:green:wlan", + .gpio = E558_V2_GPIO_LED_WLAN, + .active_low = 1, + }, +}; + +static struct gpio_keys_button e558_v2_gpio_keys[] __initdata = { + { + .desc = "reset", + .type = EV_KEY, + .code = KEY_RESTART, + .debounce_interval = E558_V2_KEYS_DEBOUNCE_INTERVAL, + .gpio = E558_V2_GPIO_BTN_RESET, + .active_low = 1, + }, +}; + +/* GMAC0 of the AR8327 switch is connected to the QCA9558 SoC via SGMII */ +static struct ar8327_pad_cfg e558_v2_ar8327_pad0_cfg = { + .mode = AR8327_PAD_MAC_SGMII, + .sgmii_delay_en = true, +}; + +/* GMAC6 of the AR8327 switch is connected to the QCA9558 SoC via RGMII */ +static struct ar8327_pad_cfg e558_v2_ar8327_pad6_cfg = { + .mode = AR8327_PAD_MAC_RGMII, + .txclk_delay_en = true, + .rxclk_delay_en = true, + .txclk_delay_sel = AR8327_CLK_DELAY_SEL1, + .rxclk_delay_sel = AR8327_CLK_DELAY_SEL2, +}; + +static const struct ar8327_led_info e558_v2_leds_qca8334[] = { + AR8327_LED_INFO(PHY2_0, HW, "e558-v2:green:wan"), + AR8327_LED_INFO(PHY3_0, HW, "e558-v2:green:lan1"), + AR8327_LED_INFO(PHY4_0, HW, "e558-v2:green:lan2"), +}; + +static struct ar8327_led_cfg e558_v2_ar8327_led_cfg = { + .led_ctrl0 = 0xc737c737, + .led_ctrl1 = 0x00000000, + .led_ctrl2 = 0x00000000, + .led_ctrl3 = 0x0030c300, + .open_drain = false, +}; + +static struct ar8327_platform_data e558_v2_ar8327_data = { + .pad0_cfg = &e558_v2_ar8327_pad0_cfg, + .pad6_cfg = &e558_v2_ar8327_pad6_cfg, + .port0_cfg = { + .force_link = 1, + .speed = AR8327_PORT_SPEED_1000, + .duplex = 1, + .txpause = 1, + .rxpause = 1, + }, + .port6_cfg = { + .force_link = 1, + .speed = AR8327_PORT_SPEED_1000, + .duplex = 1, + .txpause = 1, + .rxpause = 1, + }, + .led_cfg = &e558_v2_ar8327_led_cfg, + .leds = e558_v2_leds_qca8334, + .num_leds = ARRAY_SIZE(e558_v2_leds_qca8334), +}; + +static struct mdio_board_info e558_v2_mdio0_info[] = { + { + .bus_id = "ag71xx-mdio.0", + .phy_addr = 0, + .platform_data = &e558_v2_ar8327_data, + }, +}; + +static void __init e558_v2_setup(void) +{ + u8 *mac = (u8 *) KSEG1ADDR(0x1f050400); + u8 *art = (u8 *) KSEG1ADDR(0x1f061000); + + ath79_register_m25p80(NULL); + ath79_register_leds_gpio(-1, ARRAY_SIZE(e558_v2_leds_gpio), + e558_v2_leds_gpio); + + ath79_register_gpio_keys_polled(-1, E558_V2_KEYS_POLL_INTERVAL, + ARRAY_SIZE(e558_v2_gpio_keys), + e558_v2_gpio_keys); + + ath79_register_mdio(0, 0x0); + mdiobus_register_board_info(e558_v2_mdio0_info, + ARRAY_SIZE(e558_v2_mdio0_info)); + + ath79_setup_qca955x_eth_cfg(QCA955X_ETH_CFG_RGMII_EN); + + /* GMAC0 is connected to the RMGII interface */ + ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII; + ath79_eth0_data.phy_mask = BIT(0); + ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev; + ath79_eth0_pll_data.pll_1000 = 0x56000000; + ath79_init_mac(ath79_eth0_data.mac_addr, mac, 1); + ath79_register_eth(0); + + /* GMAC1 is connected to the SGMII interface */ + ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII; + ath79_eth1_data.speed = SPEED_1000; + ath79_eth1_data.duplex = DUPLEX_FULL; + ath79_eth1_pll_data.pll_1000 = 0x03000101; + ath79_init_mac(ath79_eth1_data.mac_addr, mac, 0); + ath79_register_eth(1); + + ath79_register_pci(); + ath79_register_usb(); + ath79_register_wmac(art, NULL); +} + +MIPS_MACHINE(ATH79_MACH_E558_V2, "E558-V2", "Qxwlan E558 v2", + e558_v2_setup); + diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h index 09b62ddee8..de1efab3a2 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h +++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h @@ -105,6 +105,7 @@ enum ath79_mach_type { ATH79_MACH_DR531, /* Wallys DR531 */ ATH79_MACH_DRAGINO2, /* Dragino Version 2 */ ATH79_MACH_E1700AC_V2, /* Qxwlan E1700AC v2 */ + ATH79_MACH_E558_V2, /* Qxwlan E558 v2 */ ATH79_MACH_E600G_V2, /* Qxwlan E600G v2 */ ATH79_MACH_E600GAC_V2, /* Qxwlan E600GAC v2 */ ATH79_MACH_EAP120, /* TP-LINK EAP120 */ -- cgit v1.2.3