From dc4eae7a8cf676911b0048b1e73c6f9adeea2f06 Mon Sep 17 00:00:00 2001 From: Christian Mehlis Date: Sun, 26 Feb 2017 12:25:57 +0100 Subject: ar71xx: Compex WPJ563 support Specification: - SoC: Qualcomm Atheros QCA9563 (775 MHz, MIPS 74Kc) - RAM: 128 MiB - Storage: 16MB NOR flash - Wireless: Built into QCA9563 (Dragonfly), PHY modes b/g/n, 3x3 MIMO - Ethernet: 2x1G Tested and working: - ethernet / switch / lan / wan - 2.4GHz SoC wifi - PCIe - leds - buzzer Ramload: - tftpboot 0x84000000 lede-ar71xx-generic-wpj563-16M-initramfs-uImage.bin - bootm 0x84000000 Install: - tftpboot 0x80500000 lede-ar71xx-generic-wpj563-16M-squashfs-sysupgrade.bin - erase 0x9f030000 +$filesize - erase 0x9f680000 +1 - cp.b $fileaddr 0x9f030000 $filesize Erasing 0x9f680000 is required because uboot defines "bootcmd=bootm 0x9f680000 || bootm 0x9f030000", so it first tries to boot the higher address. I think the 16 mb flash are intended to be used as 8+8mb for a fallback image. In my hardware only the lower address has a bootable image. But to make sure future hardware will boot lede too, I erase one block, so uboot will skip this address. Signed-off-by: Christian Mehlis --- target/linux/ar71xx/base-files/etc/board.d/02_network | 4 ++++ target/linux/ar71xx/base-files/etc/diag.sh | 3 +++ 2 files changed, 7 insertions(+) (limited to 'target/linux/ar71xx/base-files/etc') diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network b/target/linux/ar71xx/base-files/etc/board.d/02_network index e5892ac485..bf7c4dcd3c 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/02_network +++ b/target/linux/ar71xx/base-files/etc/board.d/02_network @@ -466,6 +466,10 @@ ar71xx_setup_interfaces() ucidef_add_switch "switch0" \ "5:lan" "1:wan" "6@eth0" ;; + wpj563) + ucidef_add_switch "switch0" \ + "0@eth0" "2:lan" "3:wan" + ;; wrt160nl) ucidef_set_interfaces_lan_wan "eth0.1" "eth1" ucidef_add_switch "switch0" \ diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh index fed51a17d7..3cde175664 100644 --- a/target/linux/ar71xx/base-files/etc/diag.sh +++ b/target/linux/ar71xx/base-files/etc/diag.sh @@ -469,6 +469,9 @@ get_status_led() { wpj558) status_led="$board:green:sig3" ;; + wpj563) + status_led="$board:green:sig1" + ;; wrt400n|\ wrt160nl) status_led="$board:blue:wps" -- cgit v1.2.3