From a736d912e2bad6c470c73fbf47c45ec3017371af Mon Sep 17 00:00:00 2001 From: Steven Lin Date: Mon, 2 Sep 2019 10:39:45 +0800 Subject: ipq40xx: add support for EnGenius EAP2200 SOC: IPQ4019 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB FLASH: NOR 4 MiB + NAND 128 MiB ETH: Qualcomm Atheros QCA8072 WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11a/n/ac 2:2x2 WLAN2: Qualcomm Atheros QCA9888 5GHz 802.11a/n/ac 2:2x2 INPUT: WPS Button LEDS: Power, LAN1, LAN2, WLAN 2.4GHz, WLAN 5GHz-1, WLAN 5GHz-2, OPMODE 1. Load Ramdisk via U-Boot To set up the flash memory environment, do the following: a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters: * 115200bps * 8N1 b. Confirm that the PC is connected to the board using one of the Ethernet ports. c. Set a static ip 192.168.99.8 for Ethernet that connects to board. d. The PC must have a TFTP server launched and listening on the interface to which the board is connected. e. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown. U-BOOT> set serverip 192.168.99.9 && tftpboot 0x84000000 192.168.99.8:openwrt.itb && bootm Signed-off-by: Steven Lin [copied 4.19 dts to 5.4] Signed-off-by: Christian Lamparter --- package/firmware/ipq-wifi/Makefile | 2 ++ .../firmware/ipq-wifi/board-engenius_eap2200.qca4019 | Bin 0 -> 24324 bytes .../firmware/ipq-wifi/board-engenius_eap2200.qca9888 | Bin 0 -> 12172 bytes 3 files changed, 2 insertions(+) create mode 100644 package/firmware/ipq-wifi/board-engenius_eap2200.qca4019 create mode 100644 package/firmware/ipq-wifi/board-engenius_eap2200.qca9888 (limited to 'package/firmware') diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index 610dee18e0..fc1b10343e 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -28,6 +28,7 @@ ALLWIFIBOARDS:= \ aruba_ap-303 \ avm_fritzrepeater-1200 \ dlink_dap2610 \ + engenius_eap2200 \ engenius_emd1 \ ezviz_cs-w3-wd1200g-eup \ linksys_ea8300 \ @@ -95,6 +96,7 @@ endef $(eval $(call generate-ipq-wifi-package,aruba_ap-303,Aruba AP-303)) $(eval $(call generate-ipq-wifi-package,avm_fritzrepeater-1200,AVM FRITZRepeater 1200)) $(eval $(call generate-ipq-wifi-package,dlink_dap2610,D-Link DAP-2610)) +$(eval $(call generate-ipq-wifi-package,engenius_eap2200,EnGenius EAP2200)) $(eval $(call generate-ipq-wifi-package,engenius_emd1,EnGenius EMD1)) $(eval $(call generate-ipq-wifi-package,ezviz_cs-w3-wd1200g-eup,EZVIZ CS-W3-WD1200G EUP)) $(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300)) diff --git a/package/firmware/ipq-wifi/board-engenius_eap2200.qca4019 b/package/firmware/ipq-wifi/board-engenius_eap2200.qca4019 new file mode 100644 index 0000000000..337d896d1e Binary files /dev/null and b/package/firmware/ipq-wifi/board-engenius_eap2200.qca4019 differ diff --git a/package/firmware/ipq-wifi/board-engenius_eap2200.qca9888 b/package/firmware/ipq-wifi/board-engenius_eap2200.qca9888 new file mode 100644 index 0000000000..2e938f4785 Binary files /dev/null and b/package/firmware/ipq-wifi/board-engenius_eap2200.qca9888 differ -- cgit v1.2.3