From a462412977cc25b79a7a3479527e754d85c23fd7 Mon Sep 17 00:00:00 2001 From: Sven Eckelmann Date: Mon, 23 Nov 2020 13:41:34 +0100 Subject: ath79: add support for OpenMesh OM2P-HS v1 Device specifications: ====================== * Qualcomm/Atheros AR9341 rev 1 * 535/400/200 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2x 10/100 Mbps Ethernet * 2T2R 2.4 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x fast ethernet - eth0 + 802.3af POE + builtin switch port 1 + used as LAN interface - eth1 + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 .bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp .bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/.bin Signed-off-by: Sven Eckelmann [drop redundant status from eth1] Signed-off-by: Adrian Schmutzler --- package/boot/uboot-envtools/Makefile | 2 +- package/boot/uboot-envtools/files/ath79 | 1 + 2 files changed, 2 insertions(+), 1 deletion(-) (limited to 'package/boot/uboot-envtools') diff --git a/package/boot/uboot-envtools/Makefile b/package/boot/uboot-envtools/Makefile index 539e65e762..3493332cee 100644 --- a/package/boot/uboot-envtools/Makefile +++ b/package/boot/uboot-envtools/Makefile @@ -10,7 +10,7 @@ include $(TOPDIR)/rules.mk PKG_NAME:=uboot-envtools PKG_DISTNAME:=u-boot PKG_VERSION:=2020.04 -PKG_RELEASE:=11 +PKG_RELEASE:=12 PKG_SOURCE:=$(PKG_DISTNAME)-$(PKG_VERSION).tar.bz2 PKG_SOURCE_URL:= \ diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79 index a7564bc89e..bc69d35c96 100644 --- a/package/boot/uboot-envtools/files/ath79 +++ b/package/boot/uboot-envtools/files/ath79 @@ -86,6 +86,7 @@ netgear,wndr4300sw) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x40000" "0x20000" ;; openmesh,om2p-v4|\ +openmesh,om2p-hs-v1|\ openmesh,om2p-hs-v4|\ plasmacloud,pa300|\ plasmacloud,pa300e) -- cgit v1.2.3