From daf1fdc6ade7c89f4ffb4d156f58ad76475e3ca2 Mon Sep 17 00:00:00 2001 From: David Bauer Date: Mon, 5 Sep 2022 19:23:16 +0200 Subject: ath79: add support for ZTE MF281 Add support for the ZTE MF281 battery-powered WiFi router. Hardware -------- SoC: Qualcomm Atheros QCA9563 RAM: 128M DDR2 FLASH: 2M SPI-NOR (GigaDevice GD25Q16) 128M SPI-NAND (GigaDevice) WLAN: QCA9563 2T2R 802.11 abgn QCA9886 2T2R 802.11 nac WWAN: ASRMicro ASR1826 ETH: Qualcomm Atheros QCA8337 UART: 115200 8n1 Unpopulated connector next to SIM slot (SIM) GND - RX - TX - 3V3 Don't connect 3V3 BUTTON: Reset - WPS LED: 1x debug-LED (internal) LEDs on front of the device are controlled using the modem CPU and can not be controlled by OpenWrt Installation ------------ 1. Connect to the serial console. Power up the device and interrupt autoboot when prompted 2. Connect a TFTP server reachable at 192.168.1.66 to the ethernet port. Serve the OpenWrt initramfs image as "speedbox-2.bin" 3. Boot the initramfs image using U-Boot $ setenv serverip 192.168.1.66 $ setenv ipaddr 192.168.1.154 $ tftpboot 0x84000000 speedbox-2.bin $ bootm 4. Copy the OpenWrt factory image to the device using scp and write to the NAND flash $ mtd write /path/to/openwrt/factory.bin firmware WWAN ---- The WWAN card can be used with OpenWrt. Example configuration for connection with a unauthenticated dual-stack APN: network.lte=interface network.lte.proto='ncm' network.lte.device='/dev/ttyACM0' network.lte.pdptype='IPV4V6' network.lte.apn='internet.telekom' network.lte.ipv6='auto' network.lte.delay='10' The WWAN card is running a modified version of OpenWrt and handles power-management as well as the LED controller (AW9523). A root shell can be acquired by installing adb using opkg and executing "adb shell". Signed-off-by: David Bauer (cherry picked from commit 1e1695f959e678868bb7911d059b847f38fc9cf4) --- target/linux/ath79/dts/qca9563_zte_mf281.dts | 275 +++++++++++++++++++++ target/linux/ath79/image/nand.mk | 21 +- .../ath79/nand/base-files/etc/board.d/02_network | 4 + 3 files changed, 296 insertions(+), 4 deletions(-) create mode 100644 target/linux/ath79/dts/qca9563_zte_mf281.dts diff --git a/target/linux/ath79/dts/qca9563_zte_mf281.dts b/target/linux/ath79/dts/qca9563_zte_mf281.dts new file mode 100644 index 0000000000..2f4b7316bf --- /dev/null +++ b/target/linux/ath79/dts/qca9563_zte_mf281.dts @@ -0,0 +1,275 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +// Copyright (c) 2021 Cezary Jackiewicz +// Copyright (c) 2021, 2022 Lech Perczak +// Copyright (c) 2022 David Bauer + +#include "qca956x.dtsi" + +#include +#include +#include + +/ { + model = "ZTE MF281"; + compatible = "zte,mf281", "qca,qca9563"; + + aliases { + led-boot = &led_debug; + led-failsafe = &led_debug; + led-running = &led_debug; + led-upgrade = &led_debug; + label-mac-device = ð0; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&enable_wlan_led_gpio>; + + /* Hidden SMD LED below signal strength LEDs. + * Visible through slits underside of the case. + */ + led_debug: debug { + label = "green:debug"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + wps { + label = "wps"; + linux,code = ; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; + + /* This GPIO is used to reset whole board _including_ the modem */ + gpio-restart { + compatible = "gpio-restart"; + gpios = <&gpio 5 GPIO_ACTIVE_HIGH>; + active-delay = <3000>; + inactive-delay = <1000>; + }; +}; + +&spi { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0xa0000>; + read-only; + }; + + partition@80000 { + label = "u-boot-env"; + reg = <0xa0000 0x20000>; + read-only; + }; + }; + }; + + flash@1 { + compatible = "spi-nand"; + reg = <1>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "fota-flag"; + reg = <0x000000 0xa0000>; + read-only; + }; + + partition@a0000 { + label = "art"; + reg = <0xa0000 0x80000>; + read-only; + + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + cal_caldata_1000: cal@1000 { + reg = <0x1000 0x440>; + }; + + cal_caldata_5000: cal@5000 { + reg = <0x5000 0x2f20>; + }; + }; + + partition@120000 { + label = "mac"; + reg = <0x120000 0x80000>; + read-only; + + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_mac_0: macaddr@0 { + reg = <0x0 0x6>; + }; + }; + + partition@1a0000 { + label = "reserved2"; + reg = <0x1a0000 0xc0000>; + read-only; + }; + + partition@260000 { + label = "cfg-param"; + reg = <0x260000 0x400000>; + read-only; + }; + + partition@660000 { + label = "log"; + reg = <0x660000 0x400000>; + read-only; + }; + + partition@a60000 { + label = "oops"; + reg = <0xa60000 0xa0000>; + read-only; + }; + + partition@b00000 { + label = "reserved3"; + reg = <0xb00000 0x500000>; + read-only; + }; + + partition@1000000 { + label = "web"; + reg = <0x1000000 0x800000>; + read-only; + }; + + partition@1800000 { + label = "firmware"; + reg = <0x1800000 0x1d00000>; + + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "kernel"; + reg = <0x0 0x600000>; + }; + + partition@600000 { + label = "ubi"; + reg = <0x600000 0x1700000>; + }; + }; + + partition@3500000 { + label = "data"; + reg = <0x3500000 0x1900000>; + read-only; + }; + + partition@4e00000 { + label = "fota"; + reg = <0x4e00000 0x3200000>; + read-only; + }; + }; + }; +}; + +&mdio0 { + status = "okay"; + + phy0: ethernet-phy@0 { + reg = <0>; + phy-mode = "sgmii"; + + qca,ar8327-initvals = < + 0x04 0x00080080 /* PORT0 PAD MODE CTRL */ + 0x7c 0x0000007e /* PORT0_STATUS */ + >; + }; +}; + +ð0 { + status = "okay"; + + phy-mode = "sgmii"; + phy-handle = <&phy0>; + + nvmem-cells = <&macaddr_mac_0>; + nvmem-cell-names = "mac-address"; +}; + +&pcie { + status = "okay"; + + wifi@0,0 { + compatible = "qcom,ath10k"; + reg = <0x0 0 0 0 0>; + + nvmem-cells = <&macaddr_mac_0>, <&cal_caldata_5000>; + nvmem-cell-names = "mac-address", "pre-calibration"; + mac-address-increment = <1>; + }; +}; + +&pinmux { + enable_wlan_led_gpio: pinmux_wlan_led_gpio { + pinctrl-single,bits = <0x10 0x0 0xff000000>; + }; +}; + +&wmac { + status = "okay"; + + nvmem-cells = <&macaddr_mac_0>, <&cal_caldata_1000>; + nvmem-cell-names = "mac-address", "calibration"; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&usb_phy1 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; diff --git a/target/linux/ath79/image/nand.mk b/target/linux/ath79/image/nand.mk index 726fab068f..1d086b1918 100644 --- a/target/linux/ath79/image/nand.mk +++ b/target/linux/ath79/image/nand.mk @@ -305,7 +305,7 @@ define Device/netgear_wndr4500-v3 endef TARGET_DEVICES += netgear_wndr4500-v3 -define Device/zte_mf286_common +define Device/zte_mf28x_common SOC := qca9563 DEVICE_VENDOR := ZTE DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct @@ -315,8 +315,21 @@ define Device/zte_mf286_common IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata endef +define Device/zte_mf281 + $(Device/zte_mf28x_common) + DEVICE_MODEL := MF281 + KERNEL_SIZE := 6144k + IMAGE_SIZE := 29696k + IMAGES += factory.bin + IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \ + check-size + DEVICE_PACKAGES += ath10k-firmware-qca9888-ct kmod-usb-net-rndis \ + kmod-usb-acm comgt-ncm +endef +TARGET_DEVICES += zte_mf281 + define Device/zte_mf286 - $(Device/zte_mf286_common) + $(Device/zte_mf28x_common) DEVICE_MODEL := MF286 DEVICE_PACKAGES += ath10k-firmware-qca988x-ct kmod-usb-net-qmi-wwan \ kmod-usb-serial-option uqmi @@ -324,7 +337,7 @@ endef TARGET_DEVICES += zte_mf286 define Device/zte_mf286a - $(Device/zte_mf286_common) + $(Device/zte_mf28x_common) DEVICE_MODEL := MF286A DEVICE_PACKAGES += ath10k-firmware-qca9888-ct kmod-usb-net-qmi-wwan \ kmod-usb-serial-option uqmi @@ -332,7 +345,7 @@ endef TARGET_DEVICES += zte_mf286a define Device/zte_mf286r - $(Device/zte_mf286_common) + $(Device/zte_mf28x_common) DEVICE_MODEL := MF286R DEVICE_PACKAGES += ath10k-firmware-qca9888-ct kmod-usb-net-rndis kmod-usb-acm \ comgt-ncm diff --git a/target/linux/ath79/nand/base-files/etc/board.d/02_network b/target/linux/ath79/nand/base-files/etc/board.d/02_network index bda4eeb917..b533e5be6c 100644 --- a/target/linux/ath79/nand/base-files/etc/board.d/02_network +++ b/target/linux/ath79/nand/base-files/etc/board.d/02_network @@ -50,6 +50,10 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" ;; + zte,mf281) + ucidef_add_switch "switch0" \ + "0@eth0" "5:lan" + ;; zte,mf286|\ zte,mf286a|\ zte,mf286r) -- cgit v1.2.3