aboutsummaryrefslogtreecommitdiffstats
path: root/tools
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for TP-Link RE650 v1Georgi Vlaev2019-07-171-0/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE650 v1 is a dual-band AC2600 range extender, based on MediaTek MT7621A and MT7615E. According to the wikidevi entry for RE650 this device is identical with TP-Link RE500 as hardware. This patch supports only RE650. Hardware specification: - SoC 880 MHz - MediaTek MT7621AT - 128 MB of DDR3 RAM - 16 MB - Winbond 25Q128FVSG - 4T4R 2.4 GHz - MediaTek MT7615E - 4T4R 5 GHz - MediaTek MT7615E - 1x 1 Gbps Ethernet - MT7621AT integrated - 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2)) - 4x buttons (Reset, Power, WPS, LED) - UART header (J1) - 2:GND, 3:RX, 4:TX Serial console @ 57600,8n1 Flash instructions: Upload openwrt-ramips-mt7621-tplink_re650-v1-squashfs-factory.bin from the RE650 web interface. TFTP recovery to stock firmware: Unfortunately, I can't find an easy way to recover the RE without opening the device and using modified binaries. The TFTP upload will only work if selected from u-boot, which means you have to open the device and attach to the serial console. The TFTP update procedure does *not* accept the published vendor firmware binaries. However, it allows to flash kernel + rootfs binaries, and this works if you have a backup of the original contents of the flash. It's probably possible to create special image out of the vendor binaries and use that as recovery image. Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com> [re-added variables for kernel header] Signed-off-by: David Bauer <mail@david-bauer.net>
* tools/gengetopt: Update to 2.23Daniel Engberg2019-07-084-29/+38
| | | | | | | | | Update gengetopt to 2.23 Remove 100-dependency_fix.patch, fixed upstream Rework no tests and docs patch Fix typo in copyright section Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* ath79: increase kernel partition size for CPE610v1Andrew Cameron2019-07-071-2/+2
| | | | | | | | | Increase the Kernel partition to address the issue discussed here https://forum.openwrt.org/t/cpe610-v1-sysupgrade-bin-missing-too-big/39637/5 Switch Back to the okli Loader to support increased partition size Signed-off-by: Andrew Cameron <apcameron@softhome.net> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [add <> for e-mail]
* ath79: add support for TP-Link CPE610-v1Andrew Cameron2019-06-241-0/+39
| | | | | | | | | | | | | | | | | | | | | TP-Link CPE610-v1 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on Atheros AR9344 Specifications: - Based on the same underlying hardware as the TP-Link CPE510 - Power, LAN, WLAN5G green LEDs - 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* tools/bison: Update to 3.4.1Daniel Engberg2019-06-223-16/+3
| | | | | | | Update bison to 3.4.1 Remove 010-intl-stub-compat.patch Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* tools/ccache: update to 3.7.1Deng Qingfang2019-06-082-3/+3
| | | | | | | | | Update ccache to 3.7.1 Release notes: https://ccache.dev/releasenotes.html#_ccache_3_7_1 Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* firmware-utils: jcgimage: add support for 4MiB+ imagesDavide Fioravanti2019-05-311-5/+19
| | | | | | | | | | | | | The first version of this script allowed just 4Mb factory images. With this patch is possible to set the maximum size of the payload. For an 8Mb flash, the corresponding maxsize is: 8 * 1024 * 1024 - 5 * 64 * 1024 = 8388608 - 327680 = 8060928 If the -m argument is not set, the default maximum size will be used for backward compatibility. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* firmware-utils: jcgimage: fix style and compiler warningsDavide Fioravanti2019-05-311-48/+46
| | | | | | Fixed some compilation warnings. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* Revert "bc: update to 1.07.1"Hans Dedecker2019-05-222-15/+20
| | | | | | | | | This reverts commit 0111b86f1db501d57bfee8a313fe5bebdf8b2ed9 as it breaks on Linux distributions without ed support ./fix-libmath_h: line 1: ed: command not found Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* bc: update to 1.07.1Deng Qingfang2019-05-222-20/+15
| | | | | | | Update bc to 1.07.1 Use GNU mirror Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* scons: update to 3.0.5Deng Qingfang2019-05-181-2/+2
| | | | | | Update scons to 3.0.5 Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* tools/firmware-utils: mktplinkfw2: add Qualcomm layoutsDavide Fioravanti2019-05-181-0/+12
| | | | | | | This commit adds the partition layout used by the TP-Link Archer D50 and probably by the TP-Link Archer D7 to mktplinkfw2. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* ipq40xx: add factory image for EnGenius ENS620EXTSteve Glennon2019-05-112-28/+178
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Extended mksenaofw to support new "capwap" header structure. This supports flashing from factory 3.0.0, 3.0.1, 3.1.0 and 3.5.5 firmware. Note that the factory image format changes for 3.1 and later firmware, and that the 3.1.0 and 3.5.5 Engenius firmware will refuse the factory_30.bin file. Similarly, the 3.0.0 and 3.0.1 Engenius firmware will refuse the factory_35.bin file. Flashing from the Engenius 3.1.0 firmware with the factory_35.bin firmware has not been tested, as 3.1.0 firmware (Engenius "middleFW") is only intended as part of the upgrade path to 3.5.5 firmware. Modified ipq40xx image Makefile to appropriately invoke mksenaofw with new parameters to configure the capwap header. Note that there is currently no method to return to factory firmware, so this is a one-way street. Path from factory 3.0.0 and 3.0.1 (EnGenius) software to OpenWrt is to navigate to 192.168.1.1 on the stock firmware and navigate to the firmware menu. Then copy the URL you have for that page, something like http://192.168.1.1/cgi-bin/luci/;stok=12345abcdef/admin/system/flashops and replace the trailing /admin/system/flashops with just /easyflashops You should then be presented with a simple "Firmware Upgrade" page. On that page, BE SURE TO CLEAR the "Keep Settings:" checkbox. Choose the openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_30.bin, click "Upgrade" and on the following page select "Proceed". Path from factory 3.5.5 (EnGenius) software to OpenWrt is simply to use the stock firmware update menu. Choose the openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_35.bin and click "Upload" and "Proceed". The device should then flash the OpenWrt firmware and reboot. Note that this resets the device to a default configuration with Wi-Fi disabled, LAN1/PoE acting as a WAN port (running DHCP client) and LAN2 acting as a LAN port with a DHCP server on 192.168.1.x (AP is at 192.168.1.1) Signed-off-by: Steve Glennon <s.glennon@cablelabs.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [sorry, for unfixing the 80-lines eyesores.]
* tools/ccache: update to 3.7Deng Qingfang2019-04-292-5/+4
| | | | | | | | | Update ccache to 3.7 Release notes: https://ccache.dev/releasenotes.html#_ccache_3_7 Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* tools: cbootimage: depend on automakeTomasz Maciej Nowak2019-04-071-1/+1
| | | | | | | Fix missing aclocal reported by buildbot. Fixes: 8595bb0 ("tools: add cbootimage for tegra") Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* firmware-utils: fix nec-enc build on older architecturesChristian Lamparter2019-04-061-1/+1
| | | | | | | | | | | | | | | | | | | | This patch enable gnu99 mode for the nec-enc utility which fixes the following build-breaking errors on some older architectures. nec-enc.c: In function ‘xor_data’: nec-enc.c:34:2: error: ‘for’ loop initial declarations are only allowed in C99 or C11 mode for (int i = 0; i < len; i++) { ^~~ nec-enc.c:34:2: note: use option -std=c99, -std=gnu99, -std=c11 or -std=gnu11 to compile your code nec-enc.c: In function ‘main’: nec-enc.c:101:3: error: ‘for’ loop initial declarations are only allowed in C99 or C11 mode for (int i = 0; i < n; i++) { ^~~ Spotted-By: Buildbot Fixes: fac27643f057 ("firmware-utils: add nec-enc") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* firmware-utils: add nec-encINAGAKI Hiroshi2019-04-062-0/+130
| | | | | | | | | | | | | | | | | | | | nec-enc provides firmware encoding/decoding with model specific key for NEC devices. known devices: - Aterm WF1200CR - Aterm WG1200CR - Aterm WG2600HS usage: nec-enc -i infile -o outfile -k key Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [checkpatch fixes, marked usage as noreturn, added static function, moved buf* from stack to the global data segment]
* tools/xz: Compile with PIC to fix linking errorsRosen Penev2019-04-061-2/+3
| | | | | | | | | | | I made a similar change to this here: https://github.com/openwrt/packages/pull/8159 However, it turns out this did not fix the problem as the problem has to do with tools/xz and not the xz package. The error is the same and causes linking errors as can be seen above. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools: tplink-safeloader: add C7v5 KR SupportMichael Gray2019-04-061-1/+2
| | | | | | The added entry originates from TP-Links latest Archer C7 v5 KR firmware. Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
* tools: add cbootimage-configs for tegraTomasz Maciej Nowak2019-04-062-1/+33
| | | | | | | This provides board configuraion tables for various Tegra boards needed by cbootimage tool to create flashable bootloader images. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* tools: add cbootimage for tegraTomasz Maciej Nowak2019-04-062-0/+33
| | | | | | | | | | | | | | | | | Tegra BCT and bootable flash image generator/compiler >From documentation: This project provides a tool which compiles BCT (Boot Configuration Table) images to place into the boot flash of a Tegra-based device. The tool will either: a) Compile a textual representation of a BCT into a binary image. b) Generate an entire boot image from a previously compiled BCT and a bootloader binary. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: Add support for TP-Link CPE210 v3Mario Schroen2019-04-021-0/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: Qualcomm Atheros QCA9533 (650MHz) * RAM: 64MB * Storage: 8 MB SPI NOR * Wireless: 2.4GHz N based built into SoC 2x2 * Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN Installation: Flash factory image through stock firmware WEB UI or TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Thanks to robimarko for the work inside the ar71xx tree. Thanks to adrianschmutzler for deep discussion and fixes. Signed-off-by: Mario Schroen <m.schroen@web.de> [Split into DTS/DTSI, read-only config partition in DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [renamed dtsi filename, light subject touches] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ar71xx: Use dynamic partitions for TP-Link CPE210 v2Adrian Schmutzler2019-04-021-2/+1
| | | | | | | This is also helpful to add support in ath79. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* tools/ccache: update to 3.6Deng Qingfang2019-03-242-3/+3
| | | | | | Update ccache to 3.6 Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* firmware-utils: mkdlinkfw: add kernel image offsetPawel Dembicki2019-03-241-4/+9
| | | | | | | | Some boards with JBOOT have partiton between bootloader and kernel image. This patch add possibility to change kernel partition start address. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* Revert "tools/cmake: Update to 3.14.0"Stijn Tintel2019-03-175-8/+33
| | | | | | | | The cmake bump to 3.14.0 breaks build on all targets. Revert it for now. This reverts commit a3446257a8737bfc2899c5911791873561feecc7. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* tools/libelf: Add mirrors as main site is deadDaniel Engberg2019-03-171-2/+3
| | | | | | Main site hasn't resolved for days so just add a few mirrors instead Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* tools/cmake: Update to 3.14.0Daniel Engberg2019-03-165-33/+8
| | | | | | | | | | Update CMake to 3.14.0 Refresh patches Remove inofficial fossies.org and replace with GitHub (link on official site) Remote 150-C-feature-checks-Match-warnings-more-strictly.patch as it's a no longer needed backport from upstream. Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* ath79: add support for TP-Link RE350K v1Piotr Dymacz2019-03-111-0/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE350K v1 (FCC ID: TE7RE350K) is a wall-plug AC1200 Wi-Fi range extender with 'Kasa Smart' support. Device is based on Qualcomm/Atheros QCA9558 + QCA9882 + AR8035 platform and is available only on US market. Specification: - 720/600/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of flash (SPI NOR) - 1x 1 Gbps Ethernet (AR8035) - 2T2R 2.4 GHz (QCA9558), with ext. PA (SE2565T) and LNA (SKY65971-11) - 2T2R 5 GHz (QCA9882), with ext. PA (SE5003L1-R) and LNA (SKY65981-11) - 2x U.FL connector on PCB - 2x dual-band PCB antennas - 1x LED, 2x dual-color LED (all driven by GPIO) - 3x button (app config, led, reset) - 1x mechanical on/off slide switch - 1x UART (4-pin, 2.54 mm pitch) header on PCB - 1x JTAG (8-pin, 1.27 mm pitch) header on PCB Flash instruction: Use 'factory' image directly in vendor GUI (default IP: 192.168.0.254, default credentials: admin/admin). Warning: This device does not include any kind of recovery mechanism in U-Boot. Vendor firmware access: You can access vendor firmware over serial (RX line requires jumper resistor in R306 place, near XTAL) with: root/sohoadmin credentials. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* tools: tar: update to version 1.32Daniel Golle2019-03-101-2/+2
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* cmake: match warnings more strictly in C++ feature checksMoritz Warning2019-03-101-0/+25
| | | | | | | | | Require the word "warning" to appear at the start of a line, after whitespace, or after a `:`. This is the same that CTest launchers use to match warnings. It avoids matching "warning" inside file paths. Fixed in cmake 3.14.0. Signed-off-by: Moritz Warning <moritzwarning@web.de>
* tools/mkimage: use http download server (fixes FS#2052)Felix Fietkau2019-03-071-3/+1
| | | | | | | Fixes timeouts with trying to access the FTP site. Also remove mirror2.openwrt.org, which does not keep current tarballs Signed-off-by: Felix Fietkau <nbd@nbd.name>
* tools: squashfskit4 should only depend on coreutils on non-linux systemsFelix Fietkau2019-03-031-1/+2
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* tools/squashfskit: fix version detection on non-linux systemAlexander Couzens2019-03-032-1/+22
| | | | | | | | | | | | gnu date is present in our staging_dir which means squashfskit will fail to build. Prevent also a race condition if coreutils is build after squashfskit. To prevent a race condition, depend on coreutils. Acked-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* tools: migrate from squashfs4 to squashfskit4Alexander Couzens2019-02-2812-1406/+8
| | | | | | | | | squashfskit is a fork of the squashfs-tools. squashfskit creates reproducible filesystems and includes many of the distro patches. Signed-off-by: Alexander Couzens <lynxis@fe80.eu> Tested-by: Paul Spooren <mail@aparcar.org>
* tools/isl: update to 0.20Syrone Wong2019-02-261-2/+2
| | | | Signed-off-by: Syrone Wong <wong.syrone@gmail.com>
* gemini: Generate harddisk image for DNS-313Linus Walleij2019-02-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | This makes OpenWrt build an Ext2+Ext4 partitioned image for the D-Link DNS-313 with two blank partitions, a boot partition on /dev/sda3 and a rootfs partition on /dev/sda4. This uses the methods already used in apm821xx including the tricks to convert the generated Ext2 filesystem partition to version 1 so that the firmware bootloader will properly recognize it. We patch a bit around the build files to make sure we get the rootfs size set and that genext2fs is properly built. Tested on the D-Link DNS-313. Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [Fixing and tricksing] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* firmware-tools/ptgen: Allow generation 0 size partitionsLinus Walleij2019-02-201-2/+9
| | | | | | | | | | | | The firmware on the D-Link DNS-313 NAS require two blank partitions before the boot partition. Support this if explicitly requested with a "-n" flag. Tested on the D-Link DNS-313. Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [Broken out from original patch] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* tools/mpfr: Update to 4.0.2Daniel Engberg2019-02-102-5/+5
| | | | | | | | | Update mpfr to 4.0.2 Use official site as last resort Force thread-safety functionality Refresh patches Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* tools/bison: Update to 3.3.2Daniel Engberg2019-02-102-14/+14
| | | | | | | | Update bison to 3.3.2 Enable pthreads support Refresh patches Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* tools/sed: Update to 4.7Daniel Engberg2019-02-101-2/+3
| | | | | | | Update sed to 4.7 Enable pthreads support Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* tools/tar: Update to 1.31Daniel Engberg2019-02-103-6/+6
| | | | | | | | | Update tar to 1.31 Fixes CVE-2018-20482 Switch to tar.xz tarball Refresh patches Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* ath79: add support for TP-Link Archer C2 V3 (AC900)Skirmantas Lauzikas2019-01-271-0/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the TP-link Archer C2 V3 (AC900). Specifications: - CPU: QCA9563 750Mhz - Ram: 64MB (DDR2) - Flash: 8MB (SPI NOR) - Ethernet: 5x 10/100/1000 - Wifi: QCA9563 bgn + QCA9887 an+ac - 9x Leds, 2x buttons Flash instructions: Upload openwrt-ath79-generic-tplink_archer-c2-v3-squashfs-factory.bin via the router Web interface and flash as normal firmware update. Signed-off-by: Skirmantas Lauzikas <skirmantas.lauzikas@blackraven.lt> [reorder entries, fix trailing whitespace in dts, add firmware partition compatible string, remove led default off states, use default on state for system led, reuse tplink-safeloader-uimage image build recipe, squash with dynamic partitioning commit, reword commit message, add installation instructions] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* firmware-utils: tplink-safeloader: Fix for Archer C2 V3 image generationSkirmantas Lauzikas2019-01-271-1/+2
| | | | | | | | | | | Fix for factory image generation, so that stock firmware will accept the openwrt image. Ref: https://forum.openwrt.org/t/support-for-tp-link-archer-c2-v3/15617/17 Signed-off-by: Skirmantas Lauzikas <skirmantas.lauzikas@blackraven.lt> [reword commit message, use correct order for conditions, trim trailing whitespace] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* tools: tplink-safeloader: add C7v5 RU SupportMichael Gray2019-01-271-1/+2
| | | | | | The added entry originates from TP-Links latest Archer C7 v5 RU firmware. Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
* tools: mktplinkfw2: add split-uboot layoutDavid Bauer2019-01-261-0/+6
| | | | | | | This commit adds the split-uboot partition layout used by the Archer C50 v4 to mktplinkfw2. Signed-off-by: David Bauer <mail@david-bauer.net>
* tools/sed: fix incorrect dependency.Kuang Rufan2019-01-221-2/+3
| | | | | | sed shall depend on xz instead of xz depends on sed. Signed-off-by: Kuang Rufan <master@a1983.com.cn>
* firmware-utils: mksercommfw: overhaul image creationMathias Kresin2019-01-152-272/+111
| | | | | | | | | | | | | | | | | | | | Move the zip compression into a build recipe. Pad the image using the existing build recipes as well to remove duplicate functionality Change the code to append header and footer in two steps. Allow to use a fixed filename as the netgear update image does. Use a fixed timestamp within the zip archive to make the images reproducible. Due to the changes we are now compatible to the gnu89 c standard used by default on the buildbots and we don't need to force a more recent standard anymore. Beside all changes, the footer still looks wrong in compare to the netgear update image. Signed-off-by: Mathias Kresin <dev@kresin.me>
* tools: zip: add option for reproducible archivesMathias Kresin2019-01-151-0/+145
| | | | | | | | | | | Add the option -mt/--mtime to pass a timestamp which is used as filedate for the containing files. So far, it isn't used for anything written to the extra fields, therefore requires the -X (eXclude eXtra file attributes) parameter to be effective. Signed-off-by: Mathias Kresin <dev@kresin.me>
* tools: add zip utilityMathias Kresin2019-01-159-1/+234
| | | | | | | One image requires a zip compressed image, so add the zip util found in the packages feed, and extend it with some useful debian patches. Signed-off-by: Mathias Kresin <dev@kresin.me>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-15 12:09:38 +0000