aboutsummaryrefslogtreecommitdiffstats
path: root/tools
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for TP-Link CPE710-v1Andrew Cameron2021-09-251-0/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link CPE710-v1 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on the AP152 reference board Specifications: - SoC: QCA9563-AL3A MIPS 74kc @ 775MHz, AHB @ 258MHz - RAM: 128MiB DDR2 @ 650MHz - Flash: 16MiB SPI NOR Based on the GD25Q128 - Wi-Fi 5Ghz: ath10k chip (802.11ac for up to 867Mbps on 5GHz wireless data rate) Based on the QCA9896 - Ethernet: one 1GbE port - 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector - Power, LAN, WLAN5G Blue LEDs - 3x Blue LEDs Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 30-40 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP address:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net> [convert to nvmem, fix MAC assignment in 11-ath10k-caldata] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* tools/fakeroot: fix build error on macOSFelix Fietkau2021-09-251-0/+11
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add missing information to dlink headersAlan Luck2021-09-242-0/+168
| | | | | | | | | | | | Add additional header information required for newer bootloaders found on DIR-2660-A1 & A2. Also remove the MTD splitter compatible from the second firmware partition, as OpenWrt only supports handling of the first one. Signed-off-by: Alan Luck <luckyhome2008@gmail.com> [rephrase commit message, remove removal of read-only flags] Signed-off-by: David Bauer <mail@david-bauer.net>
* libtool: Revert "libtool: bump to 2.4.6"Hauke Mehrtens2021-09-2310-444/+334
| | | | | | | | | | This breaks the package builds using the SDK. The targets all build fine, but the package builder fails on many packages. The package builder uses the OpenWrt SDK. This reverts commit c377d874bededfad971530aeb7d7e1b43cd3e61a. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* libtool: bump to 2.4.6Eneas U de Queiroz2021-09-2010-334/+444
| | | | | | | | | | | | | | | | This updates libtool to its current release, from 2015. Current patches were renumbered and given a description text. The fix in 160-passthrough-ssp.patch is no longer needed. A patch to speed up build was cherry-picked, and another openwrt specific patch was needed to not use quotes in $(SHELL), to acommodate our "SHELL=/usr/bin/env bash" usage. The already present call to ./bootstrap ensures that generated files are refreshed, so the patches are applied only to their sources. Also, that bootstrap call was adjusted to run at the appropriate time when QUILT=1. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* tools/e2fsprogs: update to 1.46.4Rosen Penev2021-09-204-5/+5
| | | | | | Refresh patches. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/autoconf-archive: update to 2021.02.19Rosen Penev2021-09-201-2/+2
| | | | Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/sstrip: update to 3.2Rosen Penev2021-09-201-2/+2
| | | | Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/sparse: update to 0.6.4Rosen Penev2021-09-201-2/+2
| | | | Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/mtools: update to 4.0.35Rosen Penev2021-09-201-2/+2
| | | | Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/m4: update to 1.4.19Rosen Penev2021-09-203-145/+2
| | | | | | Remove upstreamed patches. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/fakeroot: update to 1.26Rosen Penev2021-09-205-328/+3
| | | | | | Remove upstreamed patches. Refresh other. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/bison: update to 3.8.1Rosen Penev2021-09-202-19/+2
| | | | | | Remove upstreamed patch. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/pkgconf: update to 1.8.0Rosen Penev2021-09-162-8/+12
| | | | | | Switch to compiling with meson for faster and more reliable compilation. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools: add mesonRosen Penev2021-09-164-1/+70
| | | | | | | | | | | | | meson is a next generation build system designed to have good defaults, simpler build files, and fast compilation. It is built upon python and uses ninja for compilation. The latter provides fast by default (parallel) and problem free compilation. There are over 40 packages already successfully using meson. The next commit will convert pkgconf to use meson compilation. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/mm-macros: removeRosen Penev2021-09-162-35/+1
| | | | | | | | | | | | ccaaab1c048159611e93a181dde740f49fa12483 says that this is in the codebase because of libsigc++, which is not in the codebase anymore. Neither in base nor in packages. It doesn't seem to be needed by anything else either. GNOME packages have transitioned to using meson, which does not use m4 files. Tested local compile with CONFIG_ALL. No problems seen. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* firmware-utils: tplink-safeloader: set EAP235-Wall v1 soft-versionSander Vanheule2021-09-131-1/+1
| | | | | | | | | | | | | | | | | | | Starting with v3 of the vendor firmware for the TP-Link EAP235-Wall v1, downgrades to firmware versions below v3 as not allowed. Since OpenWrt uses version 0.0.0 as a default, this causes the factory install to fail on devices with a recent firmware. This failure is associated by the following message on the device's serial console: EAP235/230-Wall forbid fw reverted from 3.x.x to lower version! Vendor firmware (v3) also uses build and release numbers to compare images, so identical version numbers are very unlikely to cause issues. Bump the firmware version to 3.0.0 to ensure users can install OpenWrt on their devices. Reported-by: Colton Conor <colton.conor@gmail.com> Tested-by: Colton Conor <colton.conor@gmail.com> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* firmware-utils: tplink-safeloader: improve soft-version customisationSander Vanheule2021-09-132-74/+95
| | | | | | | | | | | | | | | | Some devices using the safeloader firmware format require a minimum or specific version to be set in the soft-version metadata partition. Currently only custom text values can be provided, but not all device firmware support this format. Modify the device info struct to allow for more well-defined types of soft-version overwrites, and provide a few macros for easy value initialisation. Requires all existing values to be updated to match the new structure. Signed-off-by: Sander Vanheule <sander@svanheule.net> [Adapt TL-WA1201-V2 entry too] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* firmware-utils: tplink-safeloader: use revision fieldSander Vanheule2021-09-092-1/+3
| | | | | | | | | | | | | The structured soft-version partition has a field which contains a (source) revision number. Factory images used to include this, but it was accidentaly removed during an earlier refactoring. Include the source revision number again in the generated soft-version partition. Additionaly, also show this revision number when printing image info. Fixes: 1a211af2cb3b ("firmware-utils: tplink-safeloader: refactor meta-partition generation") Signed-off-by: Sander Vanheule <sander@svanheule.net>
* tools/libtool: update to 2.4.2Ivan Pavlov2021-09-079-48/+26
| | | | | | | Refresh patches. Remove upstreamed: 001-fix-func_append.patch Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
* firmware-utils: seama.h: replace LGPL-2.1-or-later boilerplate with SPDXRafał Miłecki2021-09-071-15/+1
| | | | | | | | | | | | | | | This was missed because scancode license scanner was confused by a slightly different than expected license text (96,75% license score). License text included "file" instead of "library" in the main part of the licensing info. It also used "The GNU C Library" instead of the standard "This library" in 2nd and 3rd paragraphs. The first paragraph clearly mentions LGPL-2.1-or-later and the use of "file" instead of "library" should not affect licensing. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* tools/findutils: fix build on macosKevin Darbyshire-Bryant2021-09-061-0/+4
| | | | | | | | Use same fix as homebrew: https://github.com/Homebrew/homebrew-core/pull/69761 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ath79: add support for TP-Link TL-WA1201 v2Robert Balas2021-09-051-1/+44
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device is a wireless access point working on the 2.4 GHz and 5 GHz band, based on Qualcomm/Atheros QCA9563 + QCA9886. Specification - 775 MHz CPU - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - QCA9563: 2.4 GHz 3x3 - QCA9886: 5 GHz - AR8033: 1x 1 Gbs Ethernet - 4x LED, WPS factory reset and power button - bare UART on PCB (accessible through testpoints) Methods for Flashing: - Apply factory image in OEM firmware web-gui. Wait a minute after the progress bar completes and restart the device. - Sysupgrade on top of existing OpenWRT image - Solder wires onto UART testpoints and attach a terminal. Boot the device and press enter to enter u-boot's menu. Then issue the following commands 1. setenv serverip your-server-ip setenv ipaddr your-device-ip 2. tftp 0x80060000 openwrt-squashfs.bin (Rembember output of size in hex, henceforth "sizeinhex") 3. erase 0x9f030000 +"sizeinhex" 4. cp.b 0x80060000 0x9f030000 0x"sizeinhex" 5. reboot Recover: - U-boot serial console Signed-off-by: Robert Balas <balasr@iis.ee.ethz.ch> [convert to nvmem] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* tools/libressl: update to 3.3.4Rosen Penev2021-09-051-2/+2
| | | | Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/cmake: update to 3.21.2Rosen Penev2021-09-053-4/+4
| | | | | | Refreshed patches. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/bison: update to 3.7.6Rosen Penev2021-09-051-2/+2
| | | | Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/dosfstools: update to 4.2Rosen Penev2021-09-052-29/+2
| | | | | | Remove upstream backport. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/findutils: update to 4.8.0Rosen Penev2021-09-051-2/+2
| | | | Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/tar: update to 1.34Rosen Penev2021-09-052-3/+3
| | | | | | Refresh patch. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/zstd: update to 1.5.0Rosen Penev2021-09-051-2/+2
| | | | Signed-off-by: Rosen Penev <rosenp@gmail.com>
* firmware-utils: mkmerakifw-old: Add le32 supportMatthew Hagan2021-08-311-22/+41
| | | | | | | | | | | | | mkmerakifw-old was created for the z1 which uses the AR9344 SoC with be32 addressing. The MX64/MX65 devices use the same header style, however these boards use a BCM NSP SoC with le32 addressing. Since we may be booting initramfs images with this header, which may be of any size, within reason, board->imagelen is set to 0. The kernel image shoule be limited in the image Makefile. Signed-off-by: Matthew Hagan <mnhagan88@gmail.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: fix build on not LinuxKevin Darbyshire-Bryant2021-08-212-2/+2
| | | | Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* firmware-utils: add support for ZyXEL ZLD firmwareVincent Wiemann2021-08-212-1/+832
| | | | | | | | | | | | | | | | This commit adds a tool for extracting and creating firmware archives for: - ZyXEL NWA5121-N - ZyXEL NWA5121-NI - ZyXEL NWA5123-NI - ZyXEL NWA5123-AC - ZyXEL NWA5301 - ZyXEL NWA3560N v2 - ZyXEL WAC6100 - ZyXEL WAC6500 And maybe others... Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com>
* firmware-utils: nand_ecc: replace GPL boilerplate with SPDXRafał Miłecki2021-08-091-15/+1
| | | | | | Cc: yajin <yajin@vm-kernel.org> Cc: Felix Fietkau <nbd@nbd.name> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: trx: replace GPL-2.0-or-later boilerplate with SPDXRafał Miłecki2021-08-091-14/+1
| | | | | | | This was missed because scancode license scanner was confused by comments about crc32buf(). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: osbridge-crc: replace GPL-2.0-only boilerplate with SPDXRafał Miłecki2021-08-091-5/+1
| | | | | | | | | This was missed because scancode license scanner was confused by comments about crc32buf(). Cc: Gabor Juhos <juhosg@openwrt.org> Cc: Gabor Juhos <juhosg@freemail.hu> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: mkmylofw: replace GPL-2.0-or-later boilerplate with SPDXRafał Miłecki2021-08-091-16/+1
| | | | | | | | | This was missed because scancode license scanner was confused by a comment about (no) copyrights in the init_crc_table(). Cc: Gabor Juhos <juhosg@openwrt.org> Cc: Gabor Juhos <juhosg@freemail.hu> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: mkmerakifw-old: replace GPL-2.0-only boilerplate with SPDXRafał Miłecki2021-08-091-5/+1
| | | | | | | | | This was missed because scancode license scanner was confused by a comment about Cisco's GPL code github repository. Cc: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Christian Lamparter <chunkeey@gmail.com>
* firmware-utils: add GPL 2.0 SPDX to files with no license infoRafał Miłecki2021-08-0613-0/+13
| | | | | | These files fall under the project license: GPL-2.0-only. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: tplink-safeloader: replace BSD-2-Clause boilerplate with SPDXRafał Miłecki2021-08-061-20/+1
| | | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Matthias Schiffer <mschiffer@universe-factory.net>
* firmware-utils: seama: replace BSD-3-Clause boilerplate with SPDXRafał Miłecki2021-08-061-31/+1
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: replace GPL 2.0+ boilerplate/reference with SPDXRafał Miłecki2021-08-0627-314/+28
| | | | | | | This uses "GPL-2.0-or-later" header for files identified using scancode license scanner with 100% score as GPL 2.0 or later. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: replace GPL 2.0 boilerplate/reference with SPDXRafał Miłecki2021-08-0637-218/+36
| | | | | | | | | This uses "GPL-2.0-only" header for files identified using scancode license scanner with 100% score as GPL 2.0. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
* ath79: add support for TP-Link RE455 v1Roberto Valentini2021-07-111-0/+40
| | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE455 v1 is a dual band router/range-extender based on Qualcomm/Atheros QCA9563 + QCA9880. This device is nearly identical to RE450 v3 Specification: - 775 MHz CPU - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 3T3R 5 GHz - 1x 10/100/1000 Mbps Ethernet (AR8033 PHY) - 7x LED, 4x button - UART header on PCB[1] Flash instruction: Apply factory image in OEM firmware web-gui. [1] Didn't work, probably need to short unpopulated resistor R64 and R69 as RE450v3 Signed-off-by: Roberto Valentini <valantin89@gmail.com>
* ath79: add support for TP-Link TL-WR941HP v1Diogenes Rengo2021-07-041-0/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm Atheros TP9343 (750 MHz) Flash: 8 Mb (GigaDevice GD25Q64CSIG) RAM: 64 Mb (Zentel A3R12E40DBF-8E) Serial: yes, 4-pin header Wlan: Qualcomm Atheros TP9343, antenna: MIM0 3x3:3 RP-SMA 3 x 2.4GHz power amp module Skyworks (SiGe) SE2576L Ethernet: Qualcomm Atheros TP9343 Lan speed: 100M ports: 4 Lan speed: 100M ports: 1 Other info: same case, ram and flash that TP-Link TL-WR841HP, different SOC https://forum.openwrt.org/t/adding-device-support-tp-link-wr941hp/ Label MAC addresses based on vendor firmware: LAN *:ee label WAN *:ef label +1 WLAN *:ee label The label MAC address found in "config" partition at 0x8 Flash instruction: Upload the generated factory firmware on web interface. Signed-off-by: Diogenes Rengo <rengocbx250@gmail.com> [remove various whitespace issues, squash commits, use short 0x0] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* tools/cmake: update to 3.20.3 + build with NinjaRosen Penev2021-06-201-3/+16
| | | | | | | | | | | | | | | | | | | Compile with Ninja. Ninja compiles faster and is more stable with parallel builds. Routines copied from cmake.mk. Speed improves from: Executed in 127.47 secs fish external usr time 17.02 mins 446.00 micros 17.02 mins sys time 1.18 mins 40.00 micros 1.18 mins to: Executed in 118.91 secs fish external usr time 17.28 mins 499.00 micros 17.28 mins sys time 1.13 mins 45.00 micros 1.13 mins Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/squashfskit4: fix compilation under big endianRosen Penev2021-06-203-6/+18
| | | | | | | | | | The macro used is for the wrong struct. Just byte swap manually. Refreshed patches. Tested on sparc64. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/e2fsprogs: update to 1.46.2Rosen Penev2021-06-201-3/+3
| | | | | | Fix wrong FPIC flag to fix compilation under sparc64 Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools/libressl: update to 3.3.3Rosen Penev2021-06-201-3/+3
| | | | | | Fix wrong FPIC variable usage. Fixes compilation under sparc64 host. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* treewide: remove BUILD_PARALLEL from CMake packagesRosen Penev2021-06-191-1/+0
| | | | | | | | | | | | | It's already default. The only exception is mt76 which has Ninja disabled. Found with: git grep BUILD_PARALLEL | cut -d ':' -f 1 | sort -u > par git grep cmake.mk | cut -d ':' -f 1 > cmake comm -1 -2 par cmake Signed-off-by: Rosen Penev <rosenp@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-03 20:13:02 +0000