aboutsummaryrefslogtreecommitdiffstats
path: root/tools
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for TP-Link RE200 v2Andreas Böhler2020-02-011-0/+43
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE200 v2 is a wireless range extender with Ethernet and 2.4G and 5G WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN. Specifications -------------- - MediaTek MT7628AN (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 1x 10/100 Mbps Ethernet - UART header on PCB (57600 8n1) - 8x LED (GPIO-controlled), 2x button There are 2.4G and 5G LEDs in red and green which are controlled separately. MAC addresses ------------- The MAC address assignment matches stock firmware, i.e.: LAN : *:0D 2.4G: *:0E 5G : *:0F Installation ------------ Web Interface ------------- It is possible to upgrade to OpenWrt via the web interface. Simply flash the -factory.bin from OEM. In contrast to a stock firmware, this will not overwrite U-Boot. Serial console -------------- Opening the case is quite hard, since it is welded together. Rename the OpenWrt factory image to "test.bin", then plug in the device and quickly press "2" to enter flash mode (no line feed). Follow the prompts until OpenWrt is installed. Unfortunately, this devices does not offer a recovery mode or a tftp installation method. If the web interface upgrade fails, you have to open your device and attach serial console. Additonal notes --------------- It is possible to flash back to stock by using tplink-safeloader to create a sysupgrade image based on a stock update. After the first boot, it is necessary upgrade to another stock image, otherwise subsequent boots fail with LZMA ERROR 1 and you have to attach serial to recover the device. Signed-off-by: Andreas Böhler <dev@aboehler.at> [remove DEVICE_VARS change] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* tools/gmp: update to 6.2.0Hannu Nyman2020-01-251-2/+2
| | | | | | | | Update GNU gmp to version 6.2.0 Release notes: https://gmplib.org/gmp6.2.html Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ar71xx: use dynamic partitioning for TP-Link TL-WA850RE v2Adrian Schmutzler2020-01-221-2/+1
| | | | | | | This moves the TP-Link TL-WA850RE v2 to dynamic partitioning and will allow to use this for ath79 as well. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* tools/bison: update to 3.5Hannu Nyman2020-01-212-3/+3
| | | | | | | | | | | | | | | Update bison to 3.5 Release notes: https://lists.gnu.org/archive/html/info-gnu/2019-12/msg00002.html Note for future: release notes mention that YYPRINT macro is declared deprecated, but apparently still works for now. I found one possible use of that in scripts/config/zconf.tab.c_shipped That might be modernized at some point, but as the file is synced with the one from upstream Linux, it might get fixed there. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* tools: tplink-safeloader: update soft_ver for TP-Link Archer C6 v2 (EU)Anderson Vulczak2020-01-191-1/+1
| | | | | | | | | | | | | | | | This patch updates "soft_ver" for TP-Link Archer C6 v2 (EU). It makes possible to upload OpenWrt on lastest vendor's firmware as the web-based updater checks for major.minor version during upload. Due to that on next major/minor version update TP-Link will stop us from using the web-based firmware update tool, so it will require a new patch on soft_ver to match major and minor version. Up to today's latest stock firmware the patch (major.minor.patch) version does not matters, that allows downgrade from 1.1.4 to 1.1.1 but do not allow downgrade from 1.1.X to 1.0.X. Signed-off-by: Anderson Vulczak <andi@andi.com.br>
* ramips: add support for TP-Link RE305 v1Steffen Förster2020-01-181-0/+36
| | | | | | | | | | | | | | | | | | | | | | Specification: SoC: MediaTek MT7628AN RAM: 64MiB Flash: 8MiB Wifi: - 2.4GHz: MT7628AN - 5GHz: MT7612EN LAN: 1x 10/100 Mbps Flash instructions: Flash factory image through stock firmware WEB UI. Back to stock is possible by using TFTP and stripping down the Firmware provided by TP-Link to a initramfs. The flash space between 0x650000 and 0x7f0000 is blank in the stock firmware so I left it out as well. Signed-off-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
* tools/cmake: update to 3.16.2Hannu Nyman2020-01-184-9/+9
| | | | | | | | | Update cmake to 3.16.2 and refresh patches. Release notes: https://cmake.org/cmake/help/v3.16/release/3.16.html Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ccache: update to 3.7.7DENG Qingfang2020-01-162-3/+3
| | | | | | | | | Update ccache to 3.7.7 Release notes: https://ccache.dev/releasenotes.html#_ccache_3_7_7 Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* wrt350nv2-builder: Fix memory leakAndrea Dalla Costa2020-01-141-0/+1
| | | | | | | Add missing call to `free` for variable `buffer` in function `create_bin_file`. Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
* firmware-utils/mktitanimg: fix possible resource leakAndrea Dalla Costa2020-01-141-0/+1
| | | | | | Add missing call to `fclose` for file pointer `nsp_image`. Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
* firmware-utils/mksenaofw: fix possible memory leakAndrea Dalla Costa2020-01-141-0/+2
| | | | | | Add missing calls to `free` for variable `pmodel`. Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
* firmware-utils/mkfwimage: fix possible memory and resource leakAndrea Dalla Costa2020-01-142-0/+6
| | | | | | | | | Add missing calls to `free` for variable `mem`. Add missing call to `fclose` for variable `f`. The same changes were made in both `mkfwimage.c` and `mkfwimage2.c`. Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
* firmware-utils/mkchkimg: fix possible resource leaksAndrea Dalla Costa2020-01-141-0/+8
| | | | | | | | Add missing `fclose` calls for file pointers `kern_fp`, `fs_fp` and `out_fp`. Not closing files could lead to resource leaks. Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
* firmware-utils: fix possible memory leak and resource leakAndrea Dalla Costa2020-01-141-0/+3
| | | | | | | | | | Add missing calls to `free` for variable `buffer`. This could lead to a memory leak. Add missing call to `close` for file pointer `fdin`. This could lead to a resource leak. Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
* firmware-utils/dgfirmare: fix possible resource leakAndrea Dalla Costa2020-01-141-0/+6
| | | | | | | | Add missing calls to `fclose` in functions `write_img`, `write_rootfs` and `write_kernel`. The not-closed files could lead to resource leaks. Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
* firmware-utils: mkfwimage: add support for Ubiquiti SW devicesTobias Schramm2020-01-121-0/+9
| | | | | | | | This commit adds support for Ubiquiti ToughSwitch XP (and probably also EdgeSwitch XP) devices. They are mostly based on the same hardware as MX devices. Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* make_ext4fs: Update to version 2020-01-05Hauke Mehrtens2020-01-052-14/+3
| | | | | | | 5c201be Add LDFLAGS when building libsparse.a ec17045 make_ext4fs: fix build on musl systems Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: add support for TP-Link RE200 v1Andreas Böhler2019-12-311-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE200 v1 is a wireless range extender with Ethernet and 2.4G and 5G WiFi with internal antennas. It's based on MediaTek MT7620A+MT7610EN. Specifications -------------- - MediaTek MT7620A (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 1x 10/100 Mbps Ethernet - UART header on PCB (57600 8n1) - 8x LED (GPIO-controlled; only 6 supported), 2x button There are 2.4G and 5G LEDs in red and green which are controlled separately. The 5G LED is currently not supported, since the GPIOs couldn't be determined. Installation ------------ Web Interface ------------- It is possible to upgrade to OpenWrt via the web interface. However, the OEM firmware upgrade file is required and a tool to fix the MD5 sum of the header. This procedure overwrites U-Boot and there is not failsafe / recovery mode present! To prepare an image, you need to take the header and U-Boot (i.e. 0x200 + 0x20000 bytes) from an OEM firmware file and attach the factory image to it. Then fix the header MD5Sum1. Serial console -------------- Opening the case is quite hard, since it is welded together. Rename the OpenWrt factory image to "test.bin", then plug in the device and quickly press "2" to enter flash mode (no line feed). Follow the prompts until OpenWrt is installed. Unfortunately, this devices does not offer a recovery mode or a tftp installation method. If the web interface upgrade fails, you have to open your device and attach serial console. Since the web upgrade overwrites the boot loader, you might also brick your device. Additional notes ---------------- MAC address assignment is based on stock-firmware. For me, the device assigns the MAC on the label to Ethernet and the 2.4G WiFi, while the 5G WiFi has a separate MAC with +2. *:88 Ethernet/2.4G label, uboot 0x1fc00, userconfig 0x0158 *:89 unused userconfig 0x0160 *:8A 5G not present in flash This seems to be the first ramips device with a TP-Link v1 header. The original firmware has the string "EU" embedded, there might be some region- checking going on during the firmware upgrade process. The original firmware also contains U-Boot and thus overwrites the boot loader during upgrade. In order to flash back to stock, the first header and U-Boot need to be stripped from the original firmware. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ath79: generate firmware image for aircube-ispChristian Mauderer2019-12-311-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds a "factory" image for the aircube-isp devices. Note that the firmware can't be uploaded without prior special preparation. For the most recent instructions on how to do that, visit the OpenWRT wiki page of the Ubiquiti airCube ISP for details: https://openwrt.org/toh/ubiquiti/ubiquiti_aircube_isp Current procedure: With the original firmware 2.5.0 it is possible to upload and execute a script via the configuration. To do that download and unpack the original configuration, adapt uhttpd config to execute another lua handler (placed in the config directory) and pack and upload it again. The lua handler can call a script that mounts an overlayfs and modifies the "fwupdate.real" binary so that an unsigned image is accepted. The overlayfs is necessary because a security system (called tomoyo) doesn't allow binaries in other locations than /sbin/fwupdate.real (and maybe some more) to access the flash when executed via network. A big thanks to Torvald Menningen (Snap) from the OpenWRT forum for finding out how to patch the binary so that it accepts an unsigned image. The current step-by-step procedure is: - Use a version 2.5.0 of the original firmware. This is important because a binary file will be modified. - Download a configuration. - Unpack it (it's just a tar gz file without an ending). - Add the following to uhttpd: `````` config 'uhttpd' 'other' list listen_http 0.0.0.0:8080 list listen_http [::]:8080 option 'home' '/tmp/persistent/config/patch/www' option lua_prefix '/lua' option lua_handler '/tmp/persistent/config/patch/handler.lua' `````` - Create a `patch` subfolder. - Create a `patch/www` subfolder. - Create a `patch/handler.lua` with the following content: `````` function handle_request(env) uhttpd.send("Status: 200 OK\r\n") uhttpd.send("Content-Type: text/plain\r\n\r\n") local command = "/bin/sh /tmp/persistent/config/patch/patch.sh 2>&1" local proc = assert(io.popen(command)) for line in proc:lines() do uhttpd.send(line.."\r\n") end proc:close() end `````` - Create a `patch/patch.sh` with the following content: `````` #!/bin/sh -x set -e set -u set -x UBNTBOX_PATCHED="/tmp/fwupdate.real" MD5FILE="/tmp/patchmd5" cat <<EOF > ${MD5FILE} c33235322da5baca5a7b237c09bc8df1 /sbin/fwupdate.real EOF # check md5 of files that will be patched if ! md5sum -c ${MD5FILE} then echo "******** Error when checking files. Refuse to do anything. ********" exit 0 fi # prepare some overlay functionality LOWERDIR="/tmp/lower_root" mkdir -p ${LOWERDIR} mount -t squashfs -oro /dev/mtdblock3 ${LOWERDIR} overlay_some_path() { PATH_TO_OVERLAY=$1 ALIAS=$2 UPPERDIR="/tmp/over_${ALIAS}" WORKDIR="/tmp/over_${ALIAS}_work" mkdir -p ${UPPERDIR} mkdir -p ${WORKDIR} mount -t overlay -o lowerdir=${LOWERDIR}${PATH_TO_OVERLAY},upperdir=${UPPERDIR},workdir=${WORKDIR} overlay ${PATH_TO_OVERLAY} } # patch the ubntbox binary. overlay_some_path "/sbin" "sbin" echo -en '\x10' | dd of=/sbin/fwupdate.real conv=notrunc bs=1 count=1 seek=24598 echo "******** Done ********" `````` - Repack the configuration. - Upload it via the normal web interface. - Wait about a minute. The webserver should restart. - Now there is a second web server at port 8080 which can call the lua script. Visit the page with a web browser. Link is for example http://192.168.1.1:8080/lua - You should see the output of the script with a "*** Done ***" at the end. Note that the patches are not permanent. If you restart the router you have to re-visit the link (but not re-upload the config). - Now you can upload an unsigned binary via the normal web interface. Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
* tools: qemu: Add patches to support adapter_type and monolithicFlatBrett Mastbergen2019-12-2312-0/+2340
| | | | | | | Its way more trouble to update this to a newer version of qemu than it is to backport the two additional features we need. Signed-off-by: Brett Mastbergen <bmastbergen@untangle.com>
* tools: tplink-safeloader: fix whitespace issuesAdrian Schmutzler2019-11-271-42/+42
| | | | | | | | | This replaces tabs by spaces when preceding an equal sign. This improves consistency in the file and makes the indent look correct on all platforms. While at it, also fix one case of inconsistent leading spaces. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link Archer C6 v2 (US) and A6 (US/TW)Anderson Vulczak2019-11-271-1/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch is based on #1689 and adds support for TP-Link Archer C6 v2 (US) and A6 (US/TW). The hardware is the same as EU and RU variant, except for GPIOs (LEDS/Buttons), flash(chip/partitions) and UART being available on the board. - SOC: Qualcomm QCA9563 @ 775MHz - Flash: GigaDevice GD25Q127CS1G (16MiB) - RAM: Zentel A3R1GE40JBF (128 MiB DDR2) - Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) QCA9563 integrated (3x3) - 5GHz (ac) Qualcomm QCA9886 (2x2) - Button: 1x power, 1x reset, 1x wps - LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps - UART: 115200, 8n1 (header available on board) Known issues: - Wireless: 5GHz is known to have lower RSSI signal, it affects speed and range. Flash instructions: Upload openwrt-ath79-generic-tplink_archer-c6-v2-us-squashfs-factory.bin via the router Web interface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the router 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherA6v2_tp_recovery.bin. 4. Connect power cable to router, press and hold the reset button and turn the router on 5. Keep the reset button pressed until the WPS LED lights up 6. Wait ~150 seconds to complete flashing Flash partitioning: I've followed #1689 for defining the partition layout for this patch. The partition named as "tplink" @ 0xfd0000 is marked as read only as it is where some config for stock firmware are stored. On stock firmware those stock partitions starts at 0xfd9400 however I had not been able to make it functional starting on the same address as on stock fw, so it has been partitioned following #1689 and not the stock partition layout for this specific partition. Due to that firmware/rootfs partition lenght is 0xf80000 and not 0xf89400 as stock. According to the GPL code, the EU/RU/JP variant does have different GPIO pins assignment to LEDs and buttons, also the flash memory layout is different. GPL Source Code: https://static.tp-link.com/resources/gpl/gpl-A6v2_us.tar.gz Signed-off-by: Anderson Vulczak <andi@andi.com.br> [wrap commit message, remove soft_ver change for C6 v2 EU, move LED aliases to DTS files, remove dts-v1 in DTSI, node/property reorder in DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* tools/expat: change package source to GitHubDavid Bauer2019-11-241-1/+1
| | | | | | | According to the SourceForge page, the project is migrating to GitHub. Thus, change the source of the package to GitHub. Signed-off-by: David Bauer <mail@david-bauer.net>
* ccache: update to 3.7.6DENG Qingfang2019-11-242-3/+3
| | | | | | | | | Update ccache to 3.7.6 Release notes: https://ccache.dev/releasenotes.html#_ccache_3_7_6 Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* tools/quilt: update to 0.66Hannu Nyman2019-11-243-4/+4
| | | | | | | | | Update quilt to version 0.66 Release notes at: http://git.savannah.nongnu.org/cgit/quilt.git/tree/NEWS?id=294006e12 Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* tplink-safeloader: shorten version number of TP-Link WBS210 v2Bernhard Geier2019-11-231-3/+3
| | | | | | | | | "2.0" instead of "2.00" is sufficient and more in line with the other definitions. Signed-off-by: Bernhard Geier <freifunk@geierb.de> [commit message/title adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for the TP-LINK WBS510 V1Andrew Cameron2019-11-221-1/+2
| | | | | | | | | | | | | | | | | | | | | | This adds support for a popular low-cost 5GHz N based AP Specifications: - SoC: Atheros AR9344 - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power - Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* ath79: add support for the TP-LINK WBS510 V2Andrew Cameron2019-11-221-0/+33
| | | | | | | | | | | | | | | | | | | | | | This adds support for a popular low-cost 5GHz N based AP Specifications: - SoC: Atheros AR9344 - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power - Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* ath79: add support for the TP-LINK CPE220 V3Andrew Cameron2019-11-061-0/+41
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for a popular low-cost 2.4GHz N based AP Specifications: SoC: Qualcomm Atheros QCA9533 (650MHz) RAM: 64MB Storage: 8 MB SPI NOR Wireless: 2.4GHz N based built into SoC 2x2 Ethernet: 2x 100/10 Mbps, integrated into SoC Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 This also applies some minor changes to the common DTSI: - use &wmac for label-mac-device, as this one is actually set up in common DTSI - move &eth0 to parent DTSI - fix several leading spaces, added/removed newlines Signed-off-by: Andrew Cameron <apcameron@softhome.net> [DTS style fixes/improvements, updated commit message/title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* tools/automake: Revert "Do not use $(V) - force AM_V=1"Fredrik Olofsson2019-11-061-13/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit 43365ca66253 ("Do not use $(V) - force AM_V=1") as it breaks verbose output in automake packages, deviating from the upstream and expected behaviour. As you can see, neither make command outputs the expected verbose compile command lines: ``` $ make package/mtd-utils/{clean,compile} V=sc ... CCLD lsmtd CC nand-utils/nanddump.o CCLD nanddump ... ``` ``` $ make -C build_dir/target*/mtd-utils-2.1.1 clean ... $ make -C build_dir/target*/mtd-utils-2.1.1 V=1 ... CC lib/libmtd.o CC lib/libfec.o CC lib/common.o CC lib/libcrc32.o ``` The original reason for this commit was some packages failing to build if V is set to something other than 0 or 1. See the discussion in PR https://github.com/openwrt/openwrt/pull/2481 for how to fix this in the package Makefile. Ref: PR#2481 Acked-by: Mirko Vogt <mirko-openwrt@nanl.de> Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com> [commit title/description facelift] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for TP-Link WBS210 v2Bernhard Geier2019-11-031-0/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link WBS210 v2 is an outdoor wireless CPE for 2.4 GHz with two Ethernet ports based on Atheros AR9344 The device is the same as TP-Link CPE220 v2, but with higher TX power (27 dBm instead of 12 dBm) and two antenna connectors instead of built-in antennas. Specifications: - SoC: Atheros AR9344 - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 2.4GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power - Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP: 192.168.0.100 Stock device TFTP adress: 192.168.0.254 The TP-Link WBS devices use the same GPIOs as the CPE devices, except for the link4 LED. For this one, WBS devices use "2", while CPE devices use "16". (Tested on WBS210 v2) Signed-off-by: Bernhard Geier <freifunk@geierb.de> [added comment about GPIO] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* rules.mk: remove "$(STAGING_DIR)/include"Sebastian Kemper2019-11-021-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | "$(STAGING_DIR)/include" was carried over from buildroot-ng to OpenWrt in commit 60c1f0f64d23003a19a07d6b9638542130f6641d. buildroot has dropped this directory a long time ago. In OpenWrt the directory is still created by the PrepareStaging macro and is part of the default TARGET_CPPFLAGS. But nothing at all installs headers into this directory, nor should anything be installed under this path. Removing this directory from TARGET_CPPFLAGS will cut down the log noise a bit. Not only will CPPFLAGS be shorter, there will be less warnings set off by "-Wmissing-include-dirs" (or even failures when paired with "-Werror"). After all the directory does not even _exist_ in the SDKs, which are used on the build bots when building packages (see [1] and [2]). make[8]: Entering directory '/builder/shared-workdir/build/sdk/build_dir/target-aarch64_generic_musl/libmbim-1.20.0/src/common' CC libmbim_common_la-mbim-common.lo cc1: error: /builder/shared-workdir/build/sdk/staging_dir/target-aarch64_generic_musl/include: No such file or directory [-Werror=missing-include-dirs] cc1: all warnings being treated as errors [1] https://github.com/openwrt/packages/issues/10377 [2] https://github.com/openwrt/packages/pull/10378 Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net> Acked-by: Jo-Philipp Wich <jo@mein.io> Acked-by: Rosen Penev <rosenp@gmail.com>
* tools/mkrasimage: Add support for 128k header sizeAndré Valentin2019-10-271-3/+8
| | | | | | 128k header size support is needed for ZyXEL NBG6716. Signed-off-by: André Valentin <avalentin@marcant.net>
* tools: keep stamp file in $(STAGING_DIR_HOST)Yousong Zhou2019-10-241-2/+2
| | | | Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ar71xx: improve support for TP-Link CPE510 v2Adrian Schmutzler2019-10-211-12/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes commit bae927c551fd ("ar71xx: add support for TP-LINK CPE510 V2.0") where the support for this device wasn't optimal. Device support for the CPE510v2 so far has been a hack to enable flashing with CPE510v1 images. Those even have different hardware (e.g. additional ethernet port). With this patch, we provide proper support for this device in ar71xx. Installation: - Flash factory image through stock firmware WEB UI or through TFTP - To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. - Rename factory image to recovery.bin - Stock TFTP server IP: 192.168.0.100 - Stock device TFTP address: 192.168.0.254 Fixes: bae927c551fd ("ar71xx: add support for TP-LINK CPE510 V2.0") Signed-off-by: Andrew Cameron <apcameron@softhome.net> [Rebased onto revert commit, changed comments in mach-cpe510.c, changed commit title and description, fixed eth0 MAC address, removed eth1 initialization] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [squashed revert, added fixes tag] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* tplink-safeloader: fix compilation warningsIlya Gordeev2019-10-191-12/+13
| | | | Signed-off-by: Ilya Gordeev <Mirraz@users.noreply.github.com>
* tools/e2fsprogs: Update to version 1.45.4Josef Schlehofer2019-10-081-2/+2
| | | | | | Fixes CVE-2019-5094 Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* expat: Update to version 2.2.9Josef Schlehofer2019-10-061-2/+2
| | | | | | Fixes CVE-2019-15903 Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* ccache: update to 3.7.4DENG Qingfang2019-09-262-3/+3
| | | | | | | | | Update ccache to 3.7.4 Release notes: https://ccache.dev/releasenotes.html#_ccache_3_7_4 Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* tools/coreutils: install "touch"Felix Fietkau2019-09-251-1/+1
| | | | | | | Fixes error in setting SOURCE_DATE_EPOCH timestamp on files on rootfs prepare on non-Linux systems Signed-off-by: Felix Fietkau <nbd@nbd.name>
* scons: move to packages feedPetr Štetiar2019-09-154-62/+1
| | | | | | | | | | | | | | This patch removes scons host build tool, as commit 7087efd72a8d ("scons: move host build tool to a proper place") in the packages feed has moved scons into the new home. There are currently no packages in the master tree which would need scons, yet scons is build always as part of host tools, just in order to satisfy host build dependency of few packages in the packages feeds. Ref: https://github.com/openwrt/packages/pull/9584 Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* tools/mkimage: Update U-Boot to version 2019.07Hauke Mehrtens2019-09-0410-159/+212
| | | | | | | | | | | | | This updates the U-Boot which provides the host tools like mkimage to version 2019.07. The patches were cleaned up and it was checked if this still compiles on Linux and FreeBSD. CONFIG_FIT_SIGNATURE_MAX_SIZE is set to the default value. The patch for libressl was merged upstream. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* upslug2: Update to git repositoryRosen Penev2019-09-032-297/+7
| | | | | | | | | | | | | | This has two improvements over the current version. An autotools fix and application of the wrt350v2 patch. Cleaned up Makefile as a result of makefiles being fixed. Note that this package is not really used as it depends on orion, which is classified as broken. This is the last package that uses svn in the tree. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* tools: libelf: fix headers to trigger -Wundef warningsJo-Philipp Wich2019-09-031-0/+198
| | | | | | | | | | | | When libelf from tools/ is used for building the kernel, compilation aborts due to access to undefined defines since Kbuild adds -Wundef to the compiler flags. Patch the header files to use `#if defined(...)` instead of `#if ...` to prevent such issues. Ref: https://github.com/NixOS/nixpkgs/issues/59929 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* tools: libelf: install pkg-config fileJo-Philipp Wich2019-09-031-1/+3
| | | | | | | Install the pkg-config definition for libelf in order to allow the kernel build process discover it later on. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* tools/cmake: Update to 3.15.1Daniel Engberg2019-09-015-33/+22
| | | | | | | | | | | | Update CMake to 3.15.1 Refresh patches Remove inofficial fossies.org and replace with GitHub (link on official site) Remove 150-C-feature-checks-Match-warnings-more-strictly.patch as it's a no longer needed backport from upstream. Disable ccache if GCC is 4.8, 4.9 or 5.X to avoid build failures. Reference: https://github.com/openwrt/openwrt/pull/1929 Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* tools/mtd-utils: update to 2.1.1DENG Qingfang2019-08-273-14/+16
| | | | Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* make-ext4fs: update to HEAD of 2017-05-29 - eebda1Christian Lamparter2019-08-241-3/+3
| | | | | | | | | | | | | Update make-ext4fs to commit eebda1d55d9701ace2700d7ae461697fadf52d1f git log --pretty=oneline --abbrev-commit 484903e4..eebda1d5 eebda1d make_ext4: Add strict prototypes. bb9cf91 make_ext4fs: Remove off64_t in favor of standard off_t Created with the help of the make-package-update-commit.sh script. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* tools/e2fsprogs: Update to 1.45.3Daniel Engberg2019-08-174-36/+13
| | | | | | | | | Update e2fsprogs to 1.45.3 Remove OpenBSD patch Remove Darwin patch, neither macports or brew patches these files Add patch to avoid crond detection on host OS Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* tools/patch: apply upstream patch for cve-2019-13638Russell Senior2019-08-132-1/+39
| | | | | | | | | | | | GNU patch through 2.7.6 is vulnerable to OS shell command injection that can be exploited by opening a crafted patch file that contains an ed style diff payload with shell metacharacters. The ed editor does not need to be present on the vulnerable system. This is different from CVE-2018-1000156. https://nvd.nist.gov/vuln/detail/CVE-2019-13638 Signed-off-by: Russell Senior <russell@personaltelco.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 05:24:32 +0000