aboutsummaryrefslogtreecommitdiffstats
path: root/tools/firmware-utils
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for TP-Link RE350K v1Piotr Dymacz2019-03-111-0/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE350K v1 (FCC ID: TE7RE350K) is a wall-plug AC1200 Wi-Fi range extender with 'Kasa Smart' support. Device is based on Qualcomm/Atheros QCA9558 + QCA9882 + AR8035 platform and is available only on US market. Specification: - 720/600/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of flash (SPI NOR) - 1x 1 Gbps Ethernet (AR8035) - 2T2R 2.4 GHz (QCA9558), with ext. PA (SE2565T) and LNA (SKY65971-11) - 2T2R 5 GHz (QCA9882), with ext. PA (SE5003L1-R) and LNA (SKY65981-11) - 2x U.FL connector on PCB - 2x dual-band PCB antennas - 1x LED, 2x dual-color LED (all driven by GPIO) - 3x button (app config, led, reset) - 1x mechanical on/off slide switch - 1x UART (4-pin, 2.54 mm pitch) header on PCB - 1x JTAG (8-pin, 1.27 mm pitch) header on PCB Flash instruction: Use 'factory' image directly in vendor GUI (default IP: 192.168.0.254, default credentials: admin/admin). Warning: This device does not include any kind of recovery mechanism in U-Boot. Vendor firmware access: You can access vendor firmware over serial (RX line requires jumper resistor in R306 place, near XTAL) with: root/sohoadmin credentials. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* firmware-tools/ptgen: Allow generation 0 size partitionsLinus Walleij2019-02-201-2/+9
| | | | | | | | | | | | The firmware on the D-Link DNS-313 NAS require two blank partitions before the boot partition. Support this if explicitly requested with a "-n" flag. Tested on the D-Link DNS-313. Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [Broken out from original patch] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* ath79: add support for TP-Link Archer C2 V3 (AC900)Skirmantas Lauzikas2019-01-271-0/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the TP-link Archer C2 V3 (AC900). Specifications: - CPU: QCA9563 750Mhz - Ram: 64MB (DDR2) - Flash: 8MB (SPI NOR) - Ethernet: 5x 10/100/1000 - Wifi: QCA9563 bgn + QCA9887 an+ac - 9x Leds, 2x buttons Flash instructions: Upload openwrt-ath79-generic-tplink_archer-c2-v3-squashfs-factory.bin via the router Web interface and flash as normal firmware update. Signed-off-by: Skirmantas Lauzikas <skirmantas.lauzikas@blackraven.lt> [reorder entries, fix trailing whitespace in dts, add firmware partition compatible string, remove led default off states, use default on state for system led, reuse tplink-safeloader-uimage image build recipe, squash with dynamic partitioning commit, reword commit message, add installation instructions] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* firmware-utils: tplink-safeloader: Fix for Archer C2 V3 image generationSkirmantas Lauzikas2019-01-271-1/+2
| | | | | | | | | | | Fix for factory image generation, so that stock firmware will accept the openwrt image. Ref: https://forum.openwrt.org/t/support-for-tp-link-archer-c2-v3/15617/17 Signed-off-by: Skirmantas Lauzikas <skirmantas.lauzikas@blackraven.lt> [reword commit message, use correct order for conditions, trim trailing whitespace] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* tools: tplink-safeloader: add C7v5 RU SupportMichael Gray2019-01-271-1/+2
| | | | | | The added entry originates from TP-Links latest Archer C7 v5 RU firmware. Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
* tools: mktplinkfw2: add split-uboot layoutDavid Bauer2019-01-261-0/+6
| | | | | | | This commit adds the split-uboot partition layout used by the Archer C50 v4 to mktplinkfw2. Signed-off-by: David Bauer <mail@david-bauer.net>
* firmware-utils: mksercommfw: overhaul image creationMathias Kresin2019-01-152-272/+111
| | | | | | | | | | | | | | | | | | | | Move the zip compression into a build recipe. Pad the image using the existing build recipes as well to remove duplicate functionality Change the code to append header and footer in two steps. Allow to use a fixed filename as the netgear update image does. Use a fixed timestamp within the zip archive to make the images reproducible. Due to the changes we are now compatible to the gnu89 c standard used by default on the buildbots and we don't need to force a more recent standard anymore. Beside all changes, the footer still looks wrong in compare to the netgear update image. Signed-off-by: Mathias Kresin <dev@kresin.me>
* firmware-utils: mkdlinkfw: fix buildMathias Kresin2019-01-131-1/+1
| | | | | | | | | | | | | While we don't need the gnu99 option anymore, we still need to force the c99 standard to fix the following build error on the build bots: src/mkdlinkfw.c: In function 'find_auh_headers': src/mkdlinkfw.c:267:3: error: 'for' loop initial declarations are only allowed in C99 or C11 mode for (int i = 0; i < header_counter; i++) { ^ src/mkdlinkfw.c:267:3: note: use option -std=c99, -std=gnu99, -std=c11 or -std=gnu11 to compile your code Signed-off-by: Mathias Kresin <dev@kresin.me>
* firmware-utils: mkdlinkfw: fix error handlingMathias Kresin2019-01-131-3/+3
| | | | | | | fread() doesn't set errno, ferror need to be used to check for errors. While at it, check if we read the expect number of elements. Signed-off-by: Mathias Kresin <dev@kresin.me>
* firmware-utils: mkdlinkfw: create reproducible headerMathias Kresin2019-01-131-3/+18
| | | | | | | | Use the SOURCE_DATE_EPOCH environment variable if set instead of the current time. The used timestamp matches the timestamp of the latest commit this way and make the images reproducible. Signed-off-by: Mathias Kresin <dev@kresin.me>
* firmware-utils: mkdlinkfw: cleanup codeMathias Kresin2019-01-134-42/+5
| | | | | | | Drop unused function and macros. With the cleanup the gnu extension typeof isn't used any longer and the gnu99 compile flag can be dropped. Signed-off-by: Mathias Kresin <dev@kresin.me>
* tools/firmware-utils: fix sysupgrade typo in mkdapimg2Hans Dedecker2019-01-121-1/+1
| | | | Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* tools/firmware-utils: fix sysupgrade typo in mkdapimgHans Dedecker2019-01-121-1/+1
| | | | Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ath79: add support for TP-Link Archer C6 v2Georgi Vlaev2018-12-311-0/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for TP-Link Archer C6 v2 (EU) Hardware specification: - SOC: Qualcomm QCA9563 @ 775MHz - Flash: GigaDevice GD25Q64CSIG (8MiB) - RAM: Zentel A3R1GE40JBF (128 MiB DDR2) - Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) QCA9563 integrated (3x3) - 5GHz (ac) Qualcomm QCA9886 (2x2) - Button: 1x power, 1x reset, 1x wps - LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps - UART: There's no UART header on the board Flash instructions: Upload openwrt-ath79-generic-tplink_archer-c6-v2-squashfs-factory.bin via the router Web interface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the router 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherC6v2_tp_recovery.bin. 4. Connect power cable to router, press and hold the reset button and turn the router on 5. Keep the reset button pressed until the WPS LED lights up 6. Wait ~150 seconds to complete flashing According to the GPL source the non-EU variant has different GPIOs assigned to some of the LEDs and buttons. The flash layout might be different as well. The wikidevi entry for Archer A6/C6 assumes they are identical. Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
* firmware-utils: add hex pattern mode for xorimageINAGAKI Hiroshi2018-12-241-3/+36
| | | | | | | | | | | | This commit adds "hex pattern mode" to xorimage. This mode allows xor with a hexadecimal pattern that cannot be expressed with ASCII charactors. usage (example): xorimage -i firmware.bin -o firmware.bin.new -p 6A57190601121E4C -x Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (fix checkpatch)
* ath79: add support for TP-Link Archer A7Karl-Felix Glatzer2018-12-171-1/+41
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for TP-Link Archer A7 Specification: - SOC: QCA9563 - Flash: 16 MiB (SPI) - RAM: 128 MiB (DDR2) - Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) SoC internal - 5GHz (ac) QCA988x - USB: 1x USB 2.0 port - Button: 1x power, 1x reset, 1x wps - LED: 10x LEDs - UART: holes in PCB - Vcc, GND, RX, TX from ethernet port side - 115200n8 Flash instructions: Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin via the Webinterface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the Archer A7 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherC7v5_tp_recovery.bin 2. Connect power cable to Archer A7, press and hold the reset button and turn the router on 3. Keep the reset button pressed for ~5 seconds 4. Wait ~150 seconds to complete flashing Changes since first revision: - Flash instructions using stock image webinterface - Changed "Version 5" in model string to "v5" - Split DTS file in qca9563_tplink_archer-x7-v5.dtsi and qca9563_tplink_archer-a7-v5.dts - Firmware image is now build with dynamic partitioning - Default to ath10k-ct Changes since second revision: - Changed uboot@0 to uboot@20000 in DTS file - Fixed ordering issue in board led script - Specify firmware partition format in DTS file - Rebased Makefile device definition on common Device/tplink-safeloader-uimage definition - Merged switch section in network script (same configuration as tplink,tl-wdr3600 and tplink,tl-wdr4300) Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
* ramips: use new image build code for D-Link DCS-930 familyMathias Kresin2018-12-122-40/+0
| | | | | | | | | | | | Drop the factory images and the firmware tool to create them. They don't work any more, since the factory image has an uImage header covering the whole kernel + rootfs. This way the uImage splitter will not be able to find the rootfs and the kernel will panic later on. The factory images were most likely added at a time the board had distinct partitions for kernel and rootfs. Signed-off-by: Mathias Kresin <dev@kresin.me>
* tools: tplink-safeloader: add C7v5 EU SupportListDavid Bauer2018-11-231-1/+5
| | | | | | | | | | Currently flash from WebIF is broken for Archer C7 v5 EU models as their SupportList entries are missing. The added entries originate from TP-Links latest Archer C7 v5 EU firmware. Signed-off-by: David Bauer <mail@david-bauer.net>
* tools: firmware-utils: mksercommfw build on DarwinKevin Darbyshire-Bryant2018-11-091-2/+21
| | | | | | | | | asm/byteorder.h & hence __cpu_to_be32() doesn't exist on Darwin Shamelessly copy some byte swap functions from oseama.c Acked-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ramips: fix netgear r6120 factory image generationKoen Vandeputte2018-11-081-169/+317
| | | | | | | | | | | | | | | | | | | | | | | as indicated in commit c5bf408ed6bd "(ramips: fix image generation for mt76x8") more rework was needed to fix the other issues. Building on another machine, but using the same arch, showed the application failing again for different reasons. Fix this by completely rewriting the application, fixing following found issues: - buffer overflows, resulting in stack corruption - flaws in memory requirement calculations (too small, too large) - memory leaks - missing bounds checking on string handling - non-reproducable images, by using unitilized memory in checksum calculation - missing error handling, resulting in succes on specific image errors - endianness errors when building on BE machines - various minor build warnings - documentation did not match the code actions (header item locations) - allowing input to be decimal, hex or octal now Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: fix image generation for mt76x8Koen Vandeputte2018-11-061-1/+1
| | | | | | | | | | | | | | | | | | | | | Buildbot fails to generate images for targets also generating a Sercomm binary with following error: Opening file: /mnt/ramdisk/koen/firmware/builds/owrt_mt76x8/build_dir/target-mipsel_24kc_musl/linux-ramips_mt76x8/tmp/openwrt-ramips-mt76x8-netgear_r6120-squashfs-factory.img.rootfs.zip Filesize: 3648606 . mksercommfw: malloc.c:2427: sysmalloc: Assertion `(old_top == initial_top (av) && old_size == 0) || ((unsigned long) (old_size) >= MINSIZE && prev_inuse (old_top) && ((unsigned long) old_end & (pagesize - 1)) == 0)' failed. Makefile:287: recipe for target '/mnt/ramdisk/koen/firmware/builds/owrt_mt76x8/build_dir/target-mipsel_24kc_musl/linux-ramips_mt76x8/tmp/openwrt-ramips-mt76x8-netgear_r6120-squashfs-factory.img' failed Debugging using valgrind shows stack corruption due to a buffer overflow. The author of the generator assumes the filename ends with "root", while it should be "rootfs". Fix this by accounting for the 2 missing characters which solves the build issues. More work is required to cleanup this source, which will be done later on. Reported-by: Hannu Nyman <hannu.nyman@iki.fi> Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: fix sysupgrade generation for some targetsKoen Vandeputte2018-10-291-12/+6
| | | | | | | | | | | | | | | | | These targets are already defined as having a dynamic partition but the safeloader was not adapted for them. This causes a build warning for the sysupgrade image being too big. Targets: - c58-v1 - c60-v1 - c60-v2 - TL-WR1043 v5 - TL-WR902AC v1 - TL-WR942N V1 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: switch more targets to dynamic partitioningKoen Vandeputte2018-10-291-30/+13
| | | | | | | | | | | | | Targets: - TP-LINK ER355 - TP-LINK C25 V1 - TP-LINK C59 V1 - TP-LINK C7 V4 - TP-LINK C7 V5 Fixes build issues seen due to the kernel being too big Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: switch TP-Link RE450 v1 to dynamic partitioningRadek Dostál2018-10-291-7/+2
| | | | | | | | | | | | | | | | | As mentioned in commit 5f24933 recent changes on ar71xx (switch to 4.14, memory compaction, ...) cause an increase in kernel size, making it too big for RE450. RE450 images were not build due to the following error message: os-image partition too big (more than 1572864 bytes): Success Tested on RE450, device boots and was used to send this patch. Reported-by: Enrico Mioso <mrkiko.rs@gmail.com> Suggested-by: David Bauer <mail@david-bauer.net> Signed-off-by: Radek Dostál <rd@radekdostal.com> [rewrote commit msg keeping it tight + fixed SoB lines] Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* mkfwimage: Add image type definition for WA imagesTobias Schramm2018-10-072-47/+129
| | | | | | | | | | | | | This patch adds a new type of ubiquiti image, the WA image. First seen on the NanoStation AC loco the generic name implies that we will see this type of image on more ubiquiti devices thus it makes sense to implement it in mkfwimage. The main difference is that WA images are signed. The "END" header has been replaced by a "ENDS" header followed by a 2048 bit RSA signature. This signature is not being generated by mkfwimage and filled with 0x00. Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* firmware-utils: mkedimaximg: add "big-endianness mode" optionINAGAKI Hiroshi2018-09-101-8/+35
| | | | | | | | | In addition to the default little-endianness format, I added a mode so that we can generate firmware with big-endianness format. example: ELECOM WRC-300GHBK2-I (QCA9563) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* build: add mkrasimageDavid Bauer2018-08-282-0/+460
| | | | | | | | | | | | | | | The current make-ras.sh image generation script for the ZyXEL NBG6617 has portability issues with bash. Because of this, factory images are currently not built correctly by the OpenWRT buildbots. This commit replaces the make-ras.sh by C-written mkrasimage. The new mkrasimage is also compatible with other ZyXEL devices using the ras image-format. This is not tested with the NBG6616 but it correctly builds the header for ZyXEL factory image. Signed-off-by: David Bauer <mail@david-bauer.net>
* firmware-utils/mksercommfw: fix build with clang/macOSRyan Mounce2018-08-141-1/+1
| | | | | | | | fixes error: non-void function 'main' should return a value Fixes: FS#1770 Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* firmware-utils/mksercommfw: fix musl buildAndy Walsh2018-08-131-0/+1
| | | | | | * add missing <sys/types.h> for musl Signed-off-by: Andy Walsh <andy.walsh44+github@gmail.com>
* firmware-utils: add sercomm/netgear toolLudwig Thomeczek2018-08-132-0/+255
| | | | | | | | | | | This adds a tool to generate a firmware file accepted by Netgear or sercomm devices. They use a zip-packed rootfs with header and a custom checksum. The generated Image can be flashed via the nmrpflash tool or the webinterface of the router. Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
* ar71xx: add support for TP-LINK CPE510 V2.0Andrew Cameron2018-08-021-1/+11
| | | | | | | | Adds Support for the TP-LINK CPE510 V2.0 by TP-Link. The hardware is almost the same as the CPE510 V1.0 Follow the same processes as for the CPE510 V1.0 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* ar71xx: add support for TP-Link Archer C59 v2Keith Maika2018-07-301-0/+41
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C59v2 is a dual-band AC1350 router based on Qualcomm/Atheros QCA9561+QCA9886 chips. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - USB 2.0 port - UART header on PCB Flash instruction: - via web UI: 1. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin 2. Login to router and open the Advanced tab 3. Navigate to System Tools -> Firmware Upgrade 4. Upload firmware using the Manual Upgrade form - via TFTP: 1. Set PC to fixed ip address 192.168.0.66 2. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Keith Maika <keithm@aoeex.com>
* firmware-utils: tplink-safeloader: add calloc error handlingHyeonsik Song2018-07-041-0/+4
| | | | Signed-off-by: Hyeonsik Song <blogcin@naver.com>
* ath79: add support for TP-Link RE450 v2Peter Lundkvist2018-07-021-0/+40
| | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE450 v2 is a dual band router/range-extender based on Qualcomm/Atheros QCA9563 + QCA9880. Specification: - 775 MHz CPU - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 3T3R 5 GHz - 1x 10/100/1000 Mbps Ethernet (AR8033 PHY) - 7x LED, 4x button - UART header on PCB (needs unmounted R64 & R69 0201 resistors/jumpers) Flash instruction: Apply factory image in OEM firmware web-gui. U-Boot does not seem to have any recovery functions, so debricking requires connection via UART. Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
* firmware-utils: tplink-safeloader: switch tl-wr1043nd-v4 to dynamic partitionsLucian Cristian2018-06-271-7/+2
| | | | | | | Use the new dynamic partition split in tplink-safeloader so we no longer have to worry about kernel size increases. Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* firmware-utils: tplink-safeloader: switch RE350 to dynamic partitionsAlex Maclean2018-06-261-6/+2
| | | | | | | Use the new dynamic partition split in tplink-safeloader so we no longer have to worry about kernel size increases. Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* firmware-utils: tplink-safeloader: add dynamic partitionsAlex Maclean2018-06-261-13/+58
| | | | | | | | | | | | | | | | | Add support to dynamically split the firmware partition into os-image and file-system partitions. This is done by replacing those entries in the partition table with a single unified firmware partition, which is then split according to actual kernel image size. The factory image will have the file-system partition aligned to a 64K erase block, but the sysupgrade image skips this and aligns only the JFFS2 EOF marker to squeeze out more space. This should prevent further creeping updates to the kernel partition size while maximizing space for the overlay filesystem on smaller devices. Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* firmware-utils: mktplinkfw: add rootfs offset for combined imagesAlex Maclean2018-06-261-1/+10
| | | | | | | | | | | Add an option (-O) to calculate rootfs offset for combined images. This is needed for the TP-Link mtdsplit driver to locate the rootfs when the start is not aligned to an erase block. This will be the case for sysupgrade images produced by tplink-safeloader with upcoming dynamic partition splitting. Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* ar71xx: Add support for TP-Link CPE210 v2Adrian Schmutzler2018-06-231-0/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This PR adds support for a popular low-cost 2.4GHz N based AP Specifications: - SoC: Qualcomm Atheros QCA9533 (650MHz) - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 2.4GHz N based built into SoC 2x2 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Notes: TP-Link does not use bootstrap registers so without this patch reference clock detects as 40MHz while it is actually 25MHz. This is due to messed up bootstrap resistor configuration on the PCB. Provided GPL code just forces 25MHz reference clock. That causes booting with completely wrong clocks, for example, CPU tries to boot at 1040MHz while the stock is 650MHz. So this PR depends on PR #672 to remove 40MHz reference clock. Thanks to Sven Eckelmann <sven@narfation.org> for properly patching that. Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: add support for TP-LINK Archer C7 v5Arvid E. Picciani2018-06-201-1/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C7 v5 is a dual-band AC1750 router, based on Qualcomm/Atheros QCA9563+QCA9880. Specification: - 750/400/250 MHz (CPU/DDR/AHB - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 3T3R 5 GHz - 5x 10/100/1000 Mbps Ethernet - 10x LED, 2x button - UART header on PCB Flash instruction: 1. Upload lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin via Web interface Flash instruction using TFTP recovery: 1. Set PC to fixed ip address 192.168.0.66 2. Download lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin and rename it to ArcherC7v5_tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Arvid E. Picciani <aep@exys.org>
* ath79: add tl-wr1043nd-v4 support everything is workingLucian Cristian2018-06-181-2/+2
| | | | | | | tplink-safeloader: resize kernel partition kernel 4.14 is much bigger, resize the partition Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ipq806x: increase kernel partition size for the TP-Link Archer C2600Stefan Lippers-Hollmann2018-05-221-2/+7
| | | | | | | | | | | | | | | | | | The default image does not fit 2 MB anymore, expand os-image partition to 4 MB. Upgrading works transparently via sysupgrade in both directions. Another option would have been to merge "os-image" and "rootfs" into a single "firmware" partition using MTD_SPLIT_TPLINK_FW, but just changing the sizes of the existing partitioning has been deemed safer and actually tested on an affected device; the maximum for rootfs changes from 27 MB to 25 MB. Run-tested on TP-Link Archer C2600. Signed-off-by: Joris de Vries <joris@apptrician.nl> [slh: extend comments and commit message, rename rootfs] Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* firmware-utils: add DNS-313 image header toolLinus Walleij2018-05-052-0/+240
| | | | | | | | This tool is used to create headers on images for the D-Link DNS-313 in gemini target. Will be used after switching gemini to 4.14 kernel. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* firmware-utils: tplink-safeloader: increase RE350 kernel sizeAlex Maclean2018-04-231-3/+3
| | | | | | | | 4.14 increased kernel size, so grow the kernel partition by 128K to compensate. Fixes FS#1479. Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* ar71xx: increase kernel partition size for CPE/WBS 210/510Matthias Schiffer2018-04-101-8/+8
| | | | Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* firmware-utils: tplink-safeloader: move CPE/WBS 210/510 version metainfo to ↵Matthias Schiffer2018-04-101-20/+20
| | | | | | | | | the end Having the metainfo between kernel and rootfs prevents us from resizing the kernel partition as necessary. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: add support for TP-Link Archer C60 v2Henryk Heisig2018-04-071-0/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C60 v2 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561 + QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Flash instruction (web): Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and use OEM System Tools - Firmware Upgrade site. Flash instruction (recovery): 1. Set PC to fixed IP address 192.168.0.66 2. Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery Flash instruction (under U-Boot, using UART): tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin erase 0x9f030000 +$filesize cp.b $fileaddr 0x9f030000 $filesize reset Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* firmware-utils: image generator for D-Link DAP-1330Nicolò Veronese2018-04-052-0/+205
| | | | Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
* firmware-utils: mkdlinkfw: compile as gnu99Mathias Kresin2018-03-191-1/+1
| | | | | | Compile as gnu99 to fix the build. Signed-off-by: Mathias Kresin <dev@kresin.me>
* firmware-utils: add JBOOT bootloader image supportPawel Dembicki2018-03-184-0/+921
| | | | | | | Tested on D-Link DWR-116. Based on mktplinkfw. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>