aboutsummaryrefslogtreecommitdiffstats
path: root/tools/firmware-utils
Commit message (Collapse)AuthorAgeFilesLines
* firmware-utils: mkmerakifw-old: replace GPL-2.0-only boilerplate with SPDXRafał Miłecki2021-08-091-5/+1
| | | | | | | | | This was missed because scancode license scanner was confused by a comment about Cisco's GPL code github repository. Cc: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Christian Lamparter <chunkeey@gmail.com>
* firmware-utils: add GPL 2.0 SPDX to files with no license infoRafał Miłecki2021-08-0613-0/+13
| | | | | | These files fall under the project license: GPL-2.0-only. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: tplink-safeloader: replace BSD-2-Clause boilerplate with SPDXRafał Miłecki2021-08-061-20/+1
| | | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Matthias Schiffer <mschiffer@universe-factory.net>
* firmware-utils: seama: replace BSD-3-Clause boilerplate with SPDXRafał Miłecki2021-08-061-31/+1
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: replace GPL 2.0+ boilerplate/reference with SPDXRafał Miłecki2021-08-0627-314/+28
| | | | | | | This uses "GPL-2.0-or-later" header for files identified using scancode license scanner with 100% score as GPL 2.0 or later. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: replace GPL 2.0 boilerplate/reference with SPDXRafał Miłecki2021-08-0637-218/+36
| | | | | | | | | This uses "GPL-2.0-only" header for files identified using scancode license scanner with 100% score as GPL 2.0. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
* ath79: add support for TP-Link RE455 v1Roberto Valentini2021-07-111-0/+40
| | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE455 v1 is a dual band router/range-extender based on Qualcomm/Atheros QCA9563 + QCA9880. This device is nearly identical to RE450 v3 Specification: - 775 MHz CPU - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 3T3R 5 GHz - 1x 10/100/1000 Mbps Ethernet (AR8033 PHY) - 7x LED, 4x button - UART header on PCB[1] Flash instruction: Apply factory image in OEM firmware web-gui. [1] Didn't work, probably need to short unpopulated resistor R64 and R69 as RE450v3 Signed-off-by: Roberto Valentini <valantin89@gmail.com>
* ath79: add support for TP-Link TL-WR941HP v1Diogenes Rengo2021-07-041-0/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm Atheros TP9343 (750 MHz) Flash: 8 Mb (GigaDevice GD25Q64CSIG) RAM: 64 Mb (Zentel A3R12E40DBF-8E) Serial: yes, 4-pin header Wlan: Qualcomm Atheros TP9343, antenna: MIM0 3x3:3 RP-SMA 3 x 2.4GHz power amp module Skyworks (SiGe) SE2576L Ethernet: Qualcomm Atheros TP9343 Lan speed: 100M ports: 4 Lan speed: 100M ports: 1 Other info: same case, ram and flash that TP-Link TL-WR841HP, different SOC https://forum.openwrt.org/t/adding-device-support-tp-link-wr941hp/ Label MAC addresses based on vendor firmware: LAN *:ee label WAN *:ef label +1 WLAN *:ee label The label MAC address found in "config" partition at 0x8 Flash instruction: Upload the generated factory firmware on web interface. Signed-off-by: Diogenes Rengo <rengocbx250@gmail.com> [remove various whitespace issues, squash commits, use short 0x0] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* firmware-utils: tplink-safeloader: support Archer A6 v3 CAStijn Segers2021-06-201-0/+1
| | | | | | | | | The Canadian edition of the TP-Link Archer A6 v3 uses a different header, but otherwise it's identical to the already supported EU/US editions. Signed-off-by: Stijn Segers <foss@volatilesystems.org> Tested-by: Brian Lee <dev@leebrian.me> Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
* ramips: add support for TP-Link Archer C6 v3Amish Vishwakarma2021-06-131-0/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The patch adds support for the TP-Link Archer C6 v3 (FCC ID TE7A6V3) The patch adds identification changes to the existing TP-Link Archer A6, by Vinay Patil <post2vinay@gmail.com>, which has identical hardware. Specification ------------- MediaTek MT7621 SOC RAM: 128MB DDR3 SPI Flash: W25Q128 (16MB) Ethernet: MT7530 5x 1000Base-T WiFi 5GHz: Mediatek MT7613BE WiFi 2.4GHz: Mediatek MT7603E UART/Serial: 115200 8n1 Device Configuration & Serial Port Pins --------------------------------------- ETH Ports: LAN4 LAN3 LAN2 LAN1 WAN _______________________ | | Serial Pins: | VCC GND TXD RXD | |_____________________| LEDs: Power Wifi2G Wifi5G LAN WAN Build Output ------------ The build will generate following set of files [1] openwrt-ramips-mt7621-tplink_archer-c6-v3-initramfs-kernel.bin [2] openwrt-ramips-mt7621-tplink_archer-c6-v3-squashfs-factory.bin [3] openwrt-ramips-mt7621-tplink_archer-c6-v3-squashfs-sysupgrade.bin How to Use - Flashing from TP-Link Web Interface ------------------------------------------------ * Go to "Advanced/System Tools/Firmware Update". * Click "Browse" and upload the OpenWrt factory image: factory.bin[2] * Click the "Upgrade" button, and select "Yes" when prompted. TFTP Booting ------------ Setup a TFTP boot server with address 192.168.0.5. While starting U-boot press '4' key to stop autoboot. Copy the initramfs-kernel.bin[1] to TFTP server folder, rename as test.bin From u-boot command prompt run tftpboot followed by bootm. Recovery -------- Archer A6 V3 has recovery page activated if SPI booting from flash fails. Recovery page can be activated by powercycling the router four times before the boot process is complete. Note: TFTP boot can be activated only from u-boot serial console. Device recovery address: 192.168.0.1 Signed-off-by: Amish Vishwakarma <vishwakarma.amish@gmail.com> [fix indent] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: use dynamic partitioning for TP-Link CPE seriesMichael Pratt2021-06-051-22/+11
| | | | | | | | | | | | | | | | | | | | | | | | | CPExxx and WBSxxx boards with AR9344 SOC use the OKLI lzma kernel loader with the offset of 3 blocks of length 4k (0x3000) in order to have a fake "kernel" that cannot grow larger than how it is defined in the now static OEM partition table. Before recent changes to the mtdsplit driver, the uImage parser for OKLI only supported images that started exactly on an eraseblock boundary. The mtdsplit parser for uImage now supports identifying images with any magic number value and at any offset from the eraseblock boundary using DTS properties to define those values. So, it is no longer necessary to use fixed sizes for kernel and rootfs Tested-by: Andrew Cameron <apcameron@softhome.net> [CPE510 v2] Tested-by: Bernhard Geier <freifunk@geierb.de> [WBS210 v2] Tested-by: Petrov <d7c48mWsPKx67w2@gmail.com> [CPE210 v1] Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ramips: add support for TP-Link Archer C6U v1 (EU)Georgi Vlaev2021-05-261-0/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for TP-Link Archer C6U v1 (EU). The device is also known in some market as Archer C6 v3. This patch supports only Archer C6U v1 (EU). Specifications: -------------- * SoC: Mediatek MT7621AT 2C2T, 880MHz * RAM: 128MB DDR3 * Flash: 16MB SPI NOR flash (Winbond 25Q128) * WiFi 5GHz: Mediatek MT7613BEN (2x2:2) * WiFi 2.4GHz: Mediatek MT7603EN (2x2:2) * Ethernet: MT7630, 5x 1000Base-T. * LED: Power, WAN, LAN, WiFi 2GHz and 5GHz, USB * Buttons: Reset, WPS. * UART: Serial console (115200 8n1), J1(GND:3) * USB: One USB2 port. Installation: ------------ Install the OpenWrt factory image for C6U is from the TP-Link web interface. 1) Go to "Advanced/System Tools/Firmware Update". 2) Click "Browse" and upload the OpenWrt factory image: openwrt-ramips-mt7621-tplink_archer-c6u-v1-squashfs-factory.bin. 3) Click the "Upgrade" button, and select "Yes" when prompted. Recovery to stock firmware: -------------------------- The C6U bootloader has a failsafe mode that provides a web interface (running at 192.168.0.1) for reverting back to the stock TP-Link firmware. The failsafe interface is triggered from the serial console or on failed kernel boot. Unfortunately, there's no key combination that enables the failsafe mode. This gives us two options for recovery: 1) Recover using the serial console (J1 header). The recovery interface can be selected by hitting 'x' when prompted on boot. 2) Trigger the bootloader failsafe mode. A more dangerous option is force the bootloader into recovery mode by erasing the OpenWrt partition from the OpenWrt's shell - e.g "mtd erase firmware". Please be careful, since erasing the wrong partition can brick your device. MAC addresses: ------------- OEM firmware configuration: D8:07:B6:xx:xx:83 : 5G D8:07:B6:xx:xx:84 : LAN (label) D8:07:B6:xx:xx:84 : 2.4G D8:07:B6:xx:xx:85 : WAN Signed-off-by: Georgi Vlaev <georgi.vlaev@konsulko.com>
* ramips: add support for TP-Link Archer A6 v3Vinay Patil2021-05-261-1/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The patch adds support for the TP-Link Archer A6 v3 The router is sold in US and India with FCC ID TE7A6V3 Specification ------------- MediaTek MT7621 SOC RAM: 128MB DDR3 SPI Flash: W25Q128 (16MB) Ethernet: MT7530 5x 1000Base-T WiFi 5GHz: Mediatek MT7613BE WiFi 2.4GHz: Mediatek MT7603E UART/Serial: 115200 8n1 Device Configuration & Serial Port Pins --------------------------------------- ETH Ports: LAN4 LAN3 LAN2 LAN1 WAN _______________________ | | Serial Pins: | VCC GND TXD RXD | |_____________________| LEDs: Power Wifi2G Wifi5G LAN WAN Build Output ------------ The build will generate following set of files [1] openwrt-ramips-mt7621-tplink_archer-a6-v3-initramfs-kernel.bin [2] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-factory.bin [3] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-sysupgrade.bin How to Use - Flashing from TP-Link Web Interface ------------------------------------------------ * Go to "Advanced/System Tools/Firmware Update". * Click "Browse" and upload the OpenWrt factory image: factory.bin[2] * Click the "Upgrade" button, and select "Yes" when prompted. TFTP Booting ------------ Setup a TFTP boot server with address 192.168.0.5. While starting U-boot press '4' key to stop autoboot. Copy the initramfs-kernel.bin[1] to TFTP server folder, rename as test.bin From u-boot command prompt run tftpboot followed by bootm. Recovery -------- Archer A6 V3 has recovery page activated if SPI booting from flash fails. Recovery page can be activated from serial console only. Press 'x' while u-boot is starting Note: TFTP boot can be activated only from u-boot serial console. Device recovery address: 192.168.0.1 Thanks to: Frankis for Randmon MAC address fix. Signed-off-by: Vinay Patil <post2vinay@gmail.com> [remove superfluous factory image definition, whitespacing] Signed-off-by: David Bauer <mail@david-bauer.net>
* firmware-utils: fix coverity zytrx.c resource leakKevin Darbyshire-Bryant2021-05-201-1/+3
| | | | | | | | | | | | | | | fix coverity resource leak warning: *len = stat.st_size; mapped = mmap(NULL, stat.st_size, PROT_READ, MAP_SHARED, fd, 0); if (close(fd) < 0) CID 1484880: Resource leaks (RESOURCE_LEAK) Variable "mapped" going out of scope leaks the storage it points to. return NULL; return mapped; } Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* firmware-utils: zytrx: Add util for ZyXEL specific headerBjørn Mork2021-05-092-0/+227
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL NR7101 prepend an additional header to U-Boot images. This header use the TRX magic 0x30524448 (HDR0), but is incompatible with TRX images. This code is reverse-engineered based on matching 32 bit numbers found in the header with lengths and different checksum calculations of the vendor images found on the device. The result was matched against the validation output produced by the bootloader to name the associated header fields. Example bootloader validation output: Zyxel TRX Image 1 --> Found! Header Checksum OK ============ZyXEL header information================== chipId : MT7621A boardId : NR7101 modelId : 07 01 00 01 kernel_len : (14177560) kernelChksum : (0x8DD31F69) swVersionInt : 1.00(ABUV.0)D1 swVersionExt : 1.00(ABUV.0)D1 Zyxel TRX Image 2 --> Found! Header Checksum OK ============ZyXEL header information================== chipId : MT7621A boardId : NR7101 modelId : 07 01 00 01 kernel_len : (14176660) kernelChksum : (0x951A7637) swVersionInt : 1.00(ABUV.0)D0 swVersionExt : 1.00(ABUV.0)D0 ================================================= Check image validation: Image1 Header Magic Number --> OK Image2 Header Magic Number --> OK Image1 Header Checksum --> OK Image2 Header Checksum --> OK Image1 Data Checksum --> OK Image2 Data Checksum --> OK Image1 Stable Flag --> Stable Image1 Try Counter --> 0 Image1: OK Image2: OK The coverage and algorithm for the kernelChksum field is unknown. This field is not validated by the bootloader or the OEM firmware upgrade tool. It is therefore set to a static value for now. The swVersion fields contain free form string values. The OEM firmware use ZyXEL structured version numbers as shown above. The strings are not interpreted or validated on boot, so they can be repurposed for anything we want the bootloader to display to the user. But the OEM web GUI fails to flash images with freeform strings. The purpose of the other strings in the header is not known. The values appear to be static. We assume they are fixed for now, until we have other examples. One of these strings is the platform name, which is taken as an input parameter for support other members of the device family. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* tplink-safeloader: fix product_name of TP-Link AD7200Alex Henrie2021-05-061-1/+1
| | | | | | | | | | | | | | The stock firmware does not accept firmware with "Talon" in the name. Tested on firmware version 1.0.10 Build 20160902 rel. 57400 which came preinstalled, as well as latest firmware version 2.0.1 Build 20170103 rel.71053 flashed from AD7200v1-up-ver2-0-1-P1[20170103-rel71053]_2017-01-04_10.08.28.bin. Fixes: 1a775a4fd033 ("ipq806x: add support for TP-Link Talon AD7200") Signed-off-by: Alex Henrie <alexhenrie24@gmail.com> [added details about vendor firmware] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* firmware-utils: tplink-safeloader: support displaying fw infoRafał Miłecki2021-04-141-4/+127
| | | | | | | | | | Add "-i" option for reading & displaying firmware info. First it lists in-firmware partitions ("fwup-ptn"). Then it checks for human understandable partitions and prints data found in each of them. This new feature is meant for development & debug purposes. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: mkmylofw: fix blocks paddingRafał Miłecki2021-04-131-1/+1
| | | | | | | | | | | | | | | The old code didn't make sense as it was using "len" variable which was guaranteed to be always 0. Loop right above broken code is: while (len > 0) { } With this recent ALIGN macro fix this resulted in subtracting block size from 0 and calling write_out_padding() with a negative length. To calculate amount of bytes needed for padding & alignment it should be enough to use % 4. Fixes: a2f66229450d ("firmware-utils: fix few random warnings") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: zyimage: drop POSIX SOURCE definesRafał Miłecki2021-04-131-2/+0
| | | | | | | | | | This fixes: src/zyimage.c:10:0: warning: "_POSIX_SOURCE" redefined src/zyimage.c:11:0: warning: "_POSIX_C_SOURCE" redefined This change has been tested on Linux with -Wextra and on Mac OS. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* tplink-safeloader: fix C7v5 factory flashing from vendor fw > v1.1.xPetr Štetiar2021-04-131-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently it's not possible to flash factory images on devices shipped with vendor firmware versions 1.1.0 Build 20201120 rel. 50406 (published 2020-12-22): (curFw_ver, newFw_ver) == (1.1, 1.0) [NM_Error](nm_checkSoftVer) 00848: Firmwave not supports, check failed. [NM_Error](nm_checkUpdateContent) 01084: software version dismatched [NM_Error](nm_buildUpgradeStruct) 01188: checkUpdateContent failed. They've even following note in release notes: Note: You will be unable to downgrade to the previous firmware version after updating this firmware. This version check in vendor firmware is implemented in /usr/bin/nvrammanager binary likely as following C code[1]: sscanf(buf, "%d.%d.%*s",&upd_fw_major, &upd_fw_minor); ... if (((int)upd_fw_major < (int)cur_fw_major) || ((ret = 1, cur_fw_major == upd_fw_major && (upd_fw_minor < (int)cur_fw_minor)))) { ret = 0; printf("[NM_Error](%s) %05d: Firmwave not supports, check failed.\r\n\r\n","nm_checkSoftVer" ,0x350); } ... return ret; So in order to fix this and make it future proof it should be enough to ship our factory firmware images with major version 7 (lucky number). Tested on latest firmware version 1.1.2 Build 20210125 rel.37999: Firmwave supports, check OK. (curFw_ver, newFw_ver) == (1.1, 7.0) check firmware ok! Flashing back to vendor firmware c7v5_us-up-ver1-1-2-P1[20210125-rel37999]_2021-01-25_10.33.55.bin works as well: U-Boot 1.1.4-gbec22107-dirty (Nov 18 2020 - 18:19:12) ... Firmware downloaded... filesize = 0xeeae77 fileaddr = 0x80060000. Firmware Recovery file length : 15642231 Firmware process id 2. handle_fw_cloud 146 Image verify OK! Firmware file Verify ok! product-info:product_name:Archer C7 product_ver:5.0.0 special_id:55530000 [Error]sysmgr_cfg_checkSupportList(): 1023 @ specialId 45550000 NOT Match. Firmware supports, check OK. Firmware Recovery check ok! 1. https://gist.github.com/ynezz/2e0583647d863386a66c3d231541b6d1 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* firmware-utils: add -Wall to most toolsRafał Miłecki2021-04-091-43/+43
| | | | | | This helps spotting possible problems Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: fix -Wpointer-sign warningsRafał Miłecki2021-04-0918-54/+81
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: fix -Wmaybe-uninitialized warningsRafał Miłecki2021-04-096-4/+18
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: fix few random warningsRafał Miłecki2021-04-097-7/+3
| | | | | | | | | 1. -Wunused-label 2. -Wparentheses 3. -Wmisleading-indentation 4. -Wformat-overflow Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: fix unused variable warningsRafał Miłecki2021-04-0920-60/+18
| | | | | | | | This fixes warnings from the: 1. -Wunused-variable 2. -Wunused-but-set-variable Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: fix all -Wformat warningsRafał Miłecki2021-04-092-3/+3
| | | | | | | 1. Use %hhu for uint8_t 2. Use %z for size_t Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: bcm4908img: convert into a packageRafał Miłecki2021-04-082-998/+0
| | | | | | | | | | bcm4908img is a tool managing BCM4908 platform images. It's used for creating them as well as checking, modifying and extracting data from. It's required by both: host (for building firmware images) and target (for sysupgrade purposes). Make it a host/target package. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: bcm4908img: fix uninitialized var usageRafał Miłecki2021-04-081-3/+7
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: bcm4908img: extract bootfs without paddingRafał Miłecki2021-04-071-6/+27
| | | | | | | | JFFS2 bootfs partition in a BCM4908 image usually includes some padding. For flashing it individually (writing to designed MTD partition) we want just JFFS2 data. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: bcm4908img: fix extracting cferomRafał Miłecki2021-04-071-1/+1
| | | | | | Fix offset to extract proper data when image contains vendor header. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: bcm4908img: support extracting bootfs & rootfsRafał Miłecki2021-04-071-0/+35
| | | | | | | It's required for upgrading firmware using single partitions instead of just blindly writing whole image. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: bcm4908img: replace size with offsetRafał Miłecki2021-04-071-20/+35
| | | | | | | It's much easier to operate on BCM4908 image data with absolute offset of each section stored. It doesn't require summing sizes over and over. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: bcm4908img: add bootfs supportRafał Miłecki2021-04-051-3/+337
| | | | | | | | | | | | This adds support for accessing bootfs JFFS2 partition in the BCM4908 image. Support includes: 1. Listing files 2. Renaming file (requires unchanged name length) Above commands are useful for flashing BCM4908 images which by defualt come with cferom.000 file and require renaming it. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: bcm4908img: support extracting image dataRafał Miłecki2021-04-051-0/+87
| | | | | | It's useful for upgrading cferom, firmware, etc. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: bcm4908img: find cferom sizeRafał Miłecki2021-04-051-0/+31
| | | | | | | It's important for modifying / extracting firmware content. cferom is optional image content at the file beginning. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: bcm4908img: use "info" command displaying file infoRafał Miłecki2021-04-051-11/+20
| | | | | | | BCM4908 image format contains some info that may be useful for info / debugging purposes. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: bcm4908img: support reading from stdinRafał Miłecki2021-04-051-8/+38
| | | | | | | 1. Don't allow pipe stdin as we need to fseek() 2. Don't alow TTY as it doesn't make sense for binary input Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: bcm4908img: detect Netgear vendor firmwareRafał Miłecki2021-04-051-25/+33
| | | | | | | | Netgear uses CHK header which needs to be skipped when validating BCM4908 image. Detect it directly in the bcm4908img tool. Dealing with binary structs and endianess is way simpler in C. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: bcm4908img: extract parsing codeRafał Miłecki2021-04-051-37/+67
| | | | | | | | Move code parsing existing firmware file to separated function. This cleans up existing code and allows reusing parsing code for other commands. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: bcm4908kernel: name struct fieldsRafał Miłecki2021-03-241-8/+8
| | | | | | Less magic names / values. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: bcm4908img: name fields & valuesRafał Miłecki2021-03-241-8/+22
| | | | | | Less magic numbers Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* tools: otrx: allow own magicHauke Mehrtens2021-03-151-2/+13
| | | | | | | | | This allows to specify an own magic instead of using the default magic value TRX_MAGIC. If no own magic is specified the default one will be used. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* firmware-utils/ptgen: remove unused variable assignmentDaniel Golle2021-03-141-1/+0
| | | | | | | | | | | | | | | | Discovered by coverty: CID 1473630: Code maintainability issues (UNUSED_VALUE) Assigning value from "type_to_guid_and_name(type, &name)" to "part_guid" here, but that stored value is overwritten before it can be used. Remove the now redundant assignment of part_guid which is also set conditionally later on. Fixes: 4a078bd135 ("firmware-utils/ptgen: fix partition guid and name") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* firmware-utils/ptgen: change GPT to LBA addressingOskari Lemmela2021-03-031-13/+20
| | | | | | | | | Do not align partitions with sectors. Only kb align for GPT is supported. Use 254 heads and 63 sectors for PMBR. Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
* firmware-utils/ptgen: add support for hybrid MBROskari Lemmela2021-03-031-11/+28
| | | | | | | | | | | Adding -H option copies partition to MBR after pmbr entry. Max 3 partitions can be copied to MBR. Hybrid MBR is needed only in special cases. For example mt7622 SD card boot needs MBR entry with boot flag enabled. Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
* firmware-utils/ptgen: fix partition guid and nameOskari Lemmela2021-03-031-2/+3
| | | | | | | guid and name function should be called before storing partition info. Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
* firmware-utils/ptgen: fix compile warningsOskari Lemmela2021-03-031-2/+2
| | | | | | remove extra arguments from printf message Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
* firmware-utils/ptgen: set GPT partition attributes and nameDaniel Golle2021-02-281-10/+71
| | | | | | | | | | | Allow setting GPT partition names as used by TF-A bl2 to identify the FIP volume to load from eMMC and SD-card. While at it, also allow setting 'required' attribute as it should be used for volumes which are essential for the system to boot. Also properly handle setting the LEGACY_BOOT flag on the partition selected as 'active', as this is how it is specified in the spec. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: mt7621: add TP-Link EAP235-Wall supportSander Vanheule2021-02-191-0/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The TP-Link EAP235-Wall is a wall-mounted, PoE-powered AC1200 access point with four gigabit ethernet ports. When connecting to the device's serial port, it is strongly advised to use an isolated UART adapter. This prevents linking different power domains created by the PoE power supply, which may damage your devices. The device's U-Boot supports saving modified environments with `saveenv`. However, there is no u-boot-env partition, and saving modifications will cause the partition table to be overwritten. This is not an issue for running OpenWrt, but will prevent the vendor FW from functioning properly. Device specifications: * SoC: MT7621DAT * RAM: 128MiB * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (MT7603EN): b/g/n, 2x2 * Wireless 5GHz (MT7613BEN): a/n/ac, 2x2 * Ethernet: 4× GbE * Back side: ETH0, PoE PD port * Bottom side: ETH1, ETH2, ETH3 * Single white device LED * LED button, reset button (available for failsafe) * PoE pass-through on port ETH3 (enabled with GPIO) Datasheet of the flash chip specifies a maximum frequency of 33MHz, but that didn't work. 20MHz gives no errors with reading (flash dump) or writing (sysupgrade). Device mac addresses: Stock firmware uses the same MAC address for ethernet (on device label) and 2.4GHz wireless. The 5GHz wireless address is incremented by one. This address is stored in the 'info' ('default-mac') partition at an offset of 8 bytes. From OEM ifconfig: eth a4:2b:b0:...:88 ra0 a4:2b:b0:...:88 rai0 a4:2b:b0:...:89 Flashing instructions: * Enable SSH in the web interface, and SSH into the target device * run `cliclientd stopcs`, this should return "success" * upload the factory image via the web interface Debricking: U-boot can be interrupted during boot, serial console is 57600 baud, 8n1 This allows installing a sysupgrade image, or fixing the device in another way. * Access serial header from the side of the board, close to ETH3, pin-out is (1:TX, 2:RX, 3:GND, 4:3.3V), with pin 1 closest to ETH3. * Interrupt bootloader by holding '4' during boot, which drops the bootloader into its shell * Change default 'serverip' and 'ipaddr' variables (optional) * Download initramfs with `tftpboot`, and boot image with `bootm` # tftpboot 84000000 openwrt-initramfs.bin # bootm Revert to stock: Using the tplink-safeloader utility from the firmware-utils package, TP-Link's firmware image can be converted to an OpenWrt-compatible sysupgrade image: $ ./staging_dir/host/bin/tplink-safeloader -B EAP235-WALL-V1 \ -z EAP235-WALLv1_XXX_up_signed.bin -o eap235-sysupgrade.bin This can then be flashed using the OpenWrt sysupgrade interface. The image will appear to be incompatible and must be force flashed, without keeping the current configuration. Known issues: - DFS support is incomplete (known issue with MT7613) - MT7613 radio may stop responding when idling, reboot required. This was an issue with the ddc75ff704 version of mt76, but appears to have improved/disappeared with bc3963764d. Error notice example: [ 7099.554067] mt7615e 0000:02:00.0: Message 73 (seq 1) timeout Hardware was kindly provided for porting by Stijn Segers. Tested-by: Stijn Segers <foss@volatilesystems.org> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* tplink-safeloader: add support for TP-Link Archer A7 v5 (RU)Alexey Kunitskiy2021-02-051-1/+2
| | | | | | | | | | | | | | | | | | | Although provided in separate zip archives, the firmwares for EU and RU version are byte-identical. This adds the missing ID compared to the support-list in the vendor firmware. Note (since I checked it anyway): Partitions and support list are unchanged for all three existing firmware versions: * 20200721-rel40773 * 20201029-rel43238 * 20201120-rel50399 Signed-off-by: Alexey Kunitskiy <alexey.kv@gmail.com> [rewrite commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-03 22:05:11 +0000