aboutsummaryrefslogtreecommitdiffstats
path: root/tools/firmware-utils/src
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for TP-Link RE220 v2Rowan Border2020-06-301-0/+43
| | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE220 v2 is a wireless range extender with Ethernet and 2.4G and 5G WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN. This port of OpenWRT leverages work done by Andreas Böhler <dev@aboehler.at> for the TP-Link RE200 v2 as both devices share the same SoC, flash layout and GPIO pinout. Specifications MediaTek MT7628AN (580 Mhz) 64 MB of RAM 8 MB of FLASH 2T2R 2.4 GHz and 1T1R 5 GHz 1x 10/100 Mbps Ethernet UART header on PCB (57600 8n1) 8x LED (GPIO-controlled), 2x button There are 2.4G and 5G LEDs in red and green which are controlled separately. Web Interface Installation It is possible to upgrade to OpenWrt via the web interface. Simply flash the -factory.bin from OEM. In contrast to a stock firmware, this will not overwrite U-Boot. Signed-off-by: Rowan Border <rowanjborder@gmail.com>
* ath79: add support for TP-Link CPE610 v2Andrew Cameron2020-06-201-0/+40
| | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link CPE610 v2 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on Atheros AR9344 Specifications: - 560/450/225 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 64 MB of DDR2 RAM - 8 MB of SPI-NOR Flash - 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector - Power, LAN, WLAN5G green LEDs - 3x green RSSI LEDs Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* mkchkimg: use higher version codeJoseph C. Lehner2020-06-091-7/+2
| | | | | | | | | | | This patch changes the version code of the image header from `1.1.99_0.0.0.0` to `99.99.99_99.99.99.99`. This is neccessary on some devices where the stock firmware checks the version field, possibly preventing third-party firmware from being installed. Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org> Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
* ath79: add support for TP-Link RE450 v3Andreas Wiese2020-05-311-0/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE450 v3 is a dual band router/range-extender based on Qualcomm/Atheros QCA9563 + QCA9880. This device is nearly identical to RE450 v2 besides a modified flash layout (hence I think force-flashing a RE450v2 image will lead to at least loss of MAC address). Specification: - 775 MHz CPU - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 3T3R 5 GHz - 1x 10/100/1000 Mbps Ethernet (AR8033 PHY) - 7x LED, 4x button- - possible UART header on PCB¹ Flash instruction: Apply factory image in OEM firmware web-gui. ¹ Didn't check to connect as I didn't even manage to connect on RE450v2 (AFAIU it requires disconnecting some resistors, which I was too much of a coward to do). But given the similarities to v2 I think it's the same or very similar procedure (and most likely also the only way to debrick). Signed-off-by: Andreas Wiese <aw-openwrt@meterriblecrew.net> [remove dts-v1 and compatible in DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* firmware-utils: mkfwimage: add support for Ubiquiti XC devicesRoger Pueyo Centelles2020-05-171-0/+9
| | | | | | | | This commit adds support for Ubiquiti devices based on the XC board type, such as the PowerBeam 5AC 500. The factory binary structure is the same as the WA type. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* firmware-utils: ptgen: add GPT support李国2020-03-311-23/+318
| | | | | | | | | | | | | | | | Add GPT support to ptgen, so we can generate EFI bootable images. Introduced two options: -g generate GPT partition table -G GUID use GUID for disk and increase last bit for all partitions We drop The alternate partition table to reduce size, This may cause problems when generate vmdk images or vdi images. We have to pad enough sectors when generate these images. Signed-off-by: 李国 <uxgood.org@gmail.com> [fixed compilation on macOS] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* tplink-safeloader: update soft_ver for TP-Link Archer C6 v2 (EU)Georgi Vlaev2020-03-301-1/+1
| | | | | | | | | | | | The last couple of TP-Link firmware releases for Archer C6 v2 (EU) have switched to version 1.2.x. Bump the soft_ver to "1.2.1" to allow firmware updates from the vendor web interface. TP-Link vendor firmware releases supported by this change: * Archer C6(EU)_V2_200110: soft_ver:1.2.1 Build 20200110 rel.60119 * Archer C6(EU)_V2_191014: soft_ver:1.2.0 Build 20191014 rel.33289 Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
* ath79: add support for TP-Link Archer C60 v3Adrian Schmutzler2020-03-181-0/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C60 v3 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561 + QCA9886. It seems to be identical to the v2 revision, except that it lacks a WPS LED and has different GPIO for amber WAN LED. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 6x LED, 2x button - UART header on PCB Flash instruction (WebUI): Download *-factory.bin image and upload it via the firmwary upgrade function of the stock firmware WebUI. Flash instruction (TFTP): 1. Set PC to fixed IP address 192.168.0.66 2. Download *-factory.bin image and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery While TFTP works for OpenWrt images, my device didn't accept the only available official firmware "Archer C60(EU)_V3.0_190115.bin". In contrast to earlier revisions (v2), the v3 contains the (same) MAC address twice, once in 0x1fa08 and again in 0x1fb08. While the partition-table on the device refers to the latter, the firmware image contains a different partition-table for that region: name device firmware factory-boot 0x00000-0x1fb00 0x00000-0x1fa00 default-mac 0x1fb00-0x1fd00 0x1fa00-0x1fc00 pin 0x1fd00-0x1fe00 0x1fc00-0x1fd00 product-info 0x1fe00-0x1ff00 0x1fd00-0x1ff00 device-id 0x1ff00-0x20000 0x1ff00-0x20000 While the MAC address is present twice, other data like the PIN isn't, so with the partitioning from the firmware image the PIN on the device would actually be outside of its partition. Consequently, the patch uses the MAC location from the device (which is the same as for the v2). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mkrasimage: fix segmentation faultMichael T Farnworth2020-03-011-9/+10
| | | | | | | | | | | | | Code was attempting to determine the size of the file before it was actually known and allocating insufficient memory space. Images above a certain size caused a segmentation fault. Moving the calloc() ensured ensured that large images didn't result in a buffer overflow on memcpy(). Signed-off-by: Michael T Farnworth <michael@turf.org> [fixed name in From to match one in SoB] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* firmware-utils: add lxlfw tool for generating Luxul firmwaresDan Haab2020-02-071-0/+282
| | | | | | It's a simple tool prepending image with a Luxul header. Signed-off-by: Dan Haab <dan.haab@legrand.com>
* ramips: add support for TP-Link RE200 v2Andreas Böhler2020-02-011-0/+43
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE200 v2 is a wireless range extender with Ethernet and 2.4G and 5G WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN. Specifications -------------- - MediaTek MT7628AN (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 1x 10/100 Mbps Ethernet - UART header on PCB (57600 8n1) - 8x LED (GPIO-controlled), 2x button There are 2.4G and 5G LEDs in red and green which are controlled separately. MAC addresses ------------- The MAC address assignment matches stock firmware, i.e.: LAN : *:0D 2.4G: *:0E 5G : *:0F Installation ------------ Web Interface ------------- It is possible to upgrade to OpenWrt via the web interface. Simply flash the -factory.bin from OEM. In contrast to a stock firmware, this will not overwrite U-Boot. Serial console -------------- Opening the case is quite hard, since it is welded together. Rename the OpenWrt factory image to "test.bin", then plug in the device and quickly press "2" to enter flash mode (no line feed). Follow the prompts until OpenWrt is installed. Unfortunately, this devices does not offer a recovery mode or a tftp installation method. If the web interface upgrade fails, you have to open your device and attach serial console. Additonal notes --------------- It is possible to flash back to stock by using tplink-safeloader to create a sysupgrade image based on a stock update. After the first boot, it is necessary upgrade to another stock image, otherwise subsequent boots fail with LZMA ERROR 1 and you have to attach serial to recover the device. Signed-off-by: Andreas Böhler <dev@aboehler.at> [remove DEVICE_VARS change] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: use dynamic partitioning for TP-Link TL-WA850RE v2Adrian Schmutzler2020-01-221-2/+1
| | | | | | | This moves the TP-Link TL-WA850RE v2 to dynamic partitioning and will allow to use this for ath79 as well. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* tools: tplink-safeloader: update soft_ver for TP-Link Archer C6 v2 (EU)Anderson Vulczak2020-01-191-1/+1
| | | | | | | | | | | | | | | | This patch updates "soft_ver" for TP-Link Archer C6 v2 (EU). It makes possible to upload OpenWrt on lastest vendor's firmware as the web-based updater checks for major.minor version during upload. Due to that on next major/minor version update TP-Link will stop us from using the web-based firmware update tool, so it will require a new patch on soft_ver to match major and minor version. Up to today's latest stock firmware the patch (major.minor.patch) version does not matters, that allows downgrade from 1.1.4 to 1.1.1 but do not allow downgrade from 1.1.X to 1.0.X. Signed-off-by: Anderson Vulczak <andi@andi.com.br>
* ramips: add support for TP-Link RE305 v1Steffen Förster2020-01-181-0/+36
| | | | | | | | | | | | | | | | | | | | | | Specification: SoC: MediaTek MT7628AN RAM: 64MiB Flash: 8MiB Wifi: - 2.4GHz: MT7628AN - 5GHz: MT7612EN LAN: 1x 10/100 Mbps Flash instructions: Flash factory image through stock firmware WEB UI. Back to stock is possible by using TFTP and stripping down the Firmware provided by TP-Link to a initramfs. The flash space between 0x650000 and 0x7f0000 is blank in the stock firmware so I left it out as well. Signed-off-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
* firmware-utils/mktitanimg: fix possible resource leakAndrea Dalla Costa2020-01-141-0/+1
| | | | | | Add missing call to `fclose` for file pointer `nsp_image`. Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
* firmware-utils/mksenaofw: fix possible memory leakAndrea Dalla Costa2020-01-141-0/+2
| | | | | | Add missing calls to `free` for variable `pmodel`. Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
* firmware-utils/mkfwimage: fix possible memory and resource leakAndrea Dalla Costa2020-01-142-0/+6
| | | | | | | | | Add missing calls to `free` for variable `mem`. Add missing call to `fclose` for variable `f`. The same changes were made in both `mkfwimage.c` and `mkfwimage2.c`. Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
* firmware-utils/mkchkimg: fix possible resource leaksAndrea Dalla Costa2020-01-141-0/+8
| | | | | | | | Add missing `fclose` calls for file pointers `kern_fp`, `fs_fp` and `out_fp`. Not closing files could lead to resource leaks. Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
* firmware-utils: fix possible memory leak and resource leakAndrea Dalla Costa2020-01-141-0/+3
| | | | | | | | | | Add missing calls to `free` for variable `buffer`. This could lead to a memory leak. Add missing call to `close` for file pointer `fdin`. This could lead to a resource leak. Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
* firmware-utils/dgfirmare: fix possible resource leakAndrea Dalla Costa2020-01-141-0/+6
| | | | | | | | Add missing calls to `fclose` in functions `write_img`, `write_rootfs` and `write_kernel`. The not-closed files could lead to resource leaks. Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
* firmware-utils: mkfwimage: add support for Ubiquiti SW devicesTobias Schramm2020-01-121-0/+9
| | | | | | | | This commit adds support for Ubiquiti ToughSwitch XP (and probably also EdgeSwitch XP) devices. They are mostly based on the same hardware as MX devices. Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ramips: add support for TP-Link RE200 v1Andreas Böhler2019-12-311-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE200 v1 is a wireless range extender with Ethernet and 2.4G and 5G WiFi with internal antennas. It's based on MediaTek MT7620A+MT7610EN. Specifications -------------- - MediaTek MT7620A (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 1x 10/100 Mbps Ethernet - UART header on PCB (57600 8n1) - 8x LED (GPIO-controlled; only 6 supported), 2x button There are 2.4G and 5G LEDs in red and green which are controlled separately. The 5G LED is currently not supported, since the GPIOs couldn't be determined. Installation ------------ Web Interface ------------- It is possible to upgrade to OpenWrt via the web interface. However, the OEM firmware upgrade file is required and a tool to fix the MD5 sum of the header. This procedure overwrites U-Boot and there is not failsafe / recovery mode present! To prepare an image, you need to take the header and U-Boot (i.e. 0x200 + 0x20000 bytes) from an OEM firmware file and attach the factory image to it. Then fix the header MD5Sum1. Serial console -------------- Opening the case is quite hard, since it is welded together. Rename the OpenWrt factory image to "test.bin", then plug in the device and quickly press "2" to enter flash mode (no line feed). Follow the prompts until OpenWrt is installed. Unfortunately, this devices does not offer a recovery mode or a tftp installation method. If the web interface upgrade fails, you have to open your device and attach serial console. Since the web upgrade overwrites the boot loader, you might also brick your device. Additional notes ---------------- MAC address assignment is based on stock-firmware. For me, the device assigns the MAC on the label to Ethernet and the 2.4G WiFi, while the 5G WiFi has a separate MAC with +2. *:88 Ethernet/2.4G label, uboot 0x1fc00, userconfig 0x0158 *:89 unused userconfig 0x0160 *:8A 5G not present in flash This seems to be the first ramips device with a TP-Link v1 header. The original firmware has the string "EU" embedded, there might be some region- checking going on during the firmware upgrade process. The original firmware also contains U-Boot and thus overwrites the boot loader during upgrade. In order to flash back to stock, the first header and U-Boot need to be stripped from the original firmware. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ath79: generate firmware image for aircube-ispChristian Mauderer2019-12-311-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds a "factory" image for the aircube-isp devices. Note that the firmware can't be uploaded without prior special preparation. For the most recent instructions on how to do that, visit the OpenWRT wiki page of the Ubiquiti airCube ISP for details: https://openwrt.org/toh/ubiquiti/ubiquiti_aircube_isp Current procedure: With the original firmware 2.5.0 it is possible to upload and execute a script via the configuration. To do that download and unpack the original configuration, adapt uhttpd config to execute another lua handler (placed in the config directory) and pack and upload it again. The lua handler can call a script that mounts an overlayfs and modifies the "fwupdate.real" binary so that an unsigned image is accepted. The overlayfs is necessary because a security system (called tomoyo) doesn't allow binaries in other locations than /sbin/fwupdate.real (and maybe some more) to access the flash when executed via network. A big thanks to Torvald Menningen (Snap) from the OpenWRT forum for finding out how to patch the binary so that it accepts an unsigned image. The current step-by-step procedure is: - Use a version 2.5.0 of the original firmware. This is important because a binary file will be modified. - Download a configuration. - Unpack it (it's just a tar gz file without an ending). - Add the following to uhttpd: `````` config 'uhttpd' 'other' list listen_http 0.0.0.0:8080 list listen_http [::]:8080 option 'home' '/tmp/persistent/config/patch/www' option lua_prefix '/lua' option lua_handler '/tmp/persistent/config/patch/handler.lua' `````` - Create a `patch` subfolder. - Create a `patch/www` subfolder. - Create a `patch/handler.lua` with the following content: `````` function handle_request(env) uhttpd.send("Status: 200 OK\r\n") uhttpd.send("Content-Type: text/plain\r\n\r\n") local command = "/bin/sh /tmp/persistent/config/patch/patch.sh 2>&1" local proc = assert(io.popen(command)) for line in proc:lines() do uhttpd.send(line.."\r\n") end proc:close() end `````` - Create a `patch/patch.sh` with the following content: `````` #!/bin/sh -x set -e set -u set -x UBNTBOX_PATCHED="/tmp/fwupdate.real" MD5FILE="/tmp/patchmd5" cat <<EOF > ${MD5FILE} c33235322da5baca5a7b237c09bc8df1 /sbin/fwupdate.real EOF # check md5 of files that will be patched if ! md5sum -c ${MD5FILE} then echo "******** Error when checking files. Refuse to do anything. ********" exit 0 fi # prepare some overlay functionality LOWERDIR="/tmp/lower_root" mkdir -p ${LOWERDIR} mount -t squashfs -oro /dev/mtdblock3 ${LOWERDIR} overlay_some_path() { PATH_TO_OVERLAY=$1 ALIAS=$2 UPPERDIR="/tmp/over_${ALIAS}" WORKDIR="/tmp/over_${ALIAS}_work" mkdir -p ${UPPERDIR} mkdir -p ${WORKDIR} mount -t overlay -o lowerdir=${LOWERDIR}${PATH_TO_OVERLAY},upperdir=${UPPERDIR},workdir=${WORKDIR} overlay ${PATH_TO_OVERLAY} } # patch the ubntbox binary. overlay_some_path "/sbin" "sbin" echo -en '\x10' | dd of=/sbin/fwupdate.real conv=notrunc bs=1 count=1 seek=24598 echo "******** Done ********" `````` - Repack the configuration. - Upload it via the normal web interface. - Wait about a minute. The webserver should restart. - Now there is a second web server at port 8080 which can call the lua script. Visit the page with a web browser. Link is for example http://192.168.1.1:8080/lua - You should see the output of the script with a "*** Done ***" at the end. Note that the patches are not permanent. If you restart the router you have to re-visit the link (but not re-upload the config). - Now you can upload an unsigned binary via the normal web interface. Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
* tools: tplink-safeloader: fix whitespace issuesAdrian Schmutzler2019-11-271-42/+42
| | | | | | | | | This replaces tabs by spaces when preceding an equal sign. This improves consistency in the file and makes the indent look correct on all platforms. While at it, also fix one case of inconsistent leading spaces. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link Archer C6 v2 (US) and A6 (US/TW)Anderson Vulczak2019-11-271-1/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch is based on #1689 and adds support for TP-Link Archer C6 v2 (US) and A6 (US/TW). The hardware is the same as EU and RU variant, except for GPIOs (LEDS/Buttons), flash(chip/partitions) and UART being available on the board. - SOC: Qualcomm QCA9563 @ 775MHz - Flash: GigaDevice GD25Q127CS1G (16MiB) - RAM: Zentel A3R1GE40JBF (128 MiB DDR2) - Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) QCA9563 integrated (3x3) - 5GHz (ac) Qualcomm QCA9886 (2x2) - Button: 1x power, 1x reset, 1x wps - LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps - UART: 115200, 8n1 (header available on board) Known issues: - Wireless: 5GHz is known to have lower RSSI signal, it affects speed and range. Flash instructions: Upload openwrt-ath79-generic-tplink_archer-c6-v2-us-squashfs-factory.bin via the router Web interface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the router 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherA6v2_tp_recovery.bin. 4. Connect power cable to router, press and hold the reset button and turn the router on 5. Keep the reset button pressed until the WPS LED lights up 6. Wait ~150 seconds to complete flashing Flash partitioning: I've followed #1689 for defining the partition layout for this patch. The partition named as "tplink" @ 0xfd0000 is marked as read only as it is where some config for stock firmware are stored. On stock firmware those stock partitions starts at 0xfd9400 however I had not been able to make it functional starting on the same address as on stock fw, so it has been partitioned following #1689 and not the stock partition layout for this specific partition. Due to that firmware/rootfs partition lenght is 0xf80000 and not 0xf89400 as stock. According to the GPL code, the EU/RU/JP variant does have different GPIO pins assignment to LEDs and buttons, also the flash memory layout is different. GPL Source Code: https://static.tp-link.com/resources/gpl/gpl-A6v2_us.tar.gz Signed-off-by: Anderson Vulczak <andi@andi.com.br> [wrap commit message, remove soft_ver change for C6 v2 EU, move LED aliases to DTS files, remove dts-v1 in DTSI, node/property reorder in DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* tplink-safeloader: shorten version number of TP-Link WBS210 v2Bernhard Geier2019-11-231-3/+3
| | | | | | | | | "2.0" instead of "2.00" is sufficient and more in line with the other definitions. Signed-off-by: Bernhard Geier <freifunk@geierb.de> [commit message/title adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for the TP-LINK WBS510 V1Andrew Cameron2019-11-221-1/+2
| | | | | | | | | | | | | | | | | | | | | | This adds support for a popular low-cost 5GHz N based AP Specifications: - SoC: Atheros AR9344 - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power - Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* ath79: add support for the TP-LINK WBS510 V2Andrew Cameron2019-11-221-0/+33
| | | | | | | | | | | | | | | | | | | | | | This adds support for a popular low-cost 5GHz N based AP Specifications: - SoC: Atheros AR9344 - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power - Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* ath79: add support for the TP-LINK CPE220 V3Andrew Cameron2019-11-061-0/+41
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for a popular low-cost 2.4GHz N based AP Specifications: SoC: Qualcomm Atheros QCA9533 (650MHz) RAM: 64MB Storage: 8 MB SPI NOR Wireless: 2.4GHz N based built into SoC 2x2 Ethernet: 2x 100/10 Mbps, integrated into SoC Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 This also applies some minor changes to the common DTSI: - use &wmac for label-mac-device, as this one is actually set up in common DTSI - move &eth0 to parent DTSI - fix several leading spaces, added/removed newlines Signed-off-by: Andrew Cameron <apcameron@softhome.net> [DTS style fixes/improvements, updated commit message/title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link WBS210 v2Bernhard Geier2019-11-031-0/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link WBS210 v2 is an outdoor wireless CPE for 2.4 GHz with two Ethernet ports based on Atheros AR9344 The device is the same as TP-Link CPE220 v2, but with higher TX power (27 dBm instead of 12 dBm) and two antenna connectors instead of built-in antennas. Specifications: - SoC: Atheros AR9344 - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 2.4GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power - Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP: 192.168.0.100 Stock device TFTP adress: 192.168.0.254 The TP-Link WBS devices use the same GPIOs as the CPE devices, except for the link4 LED. For this one, WBS devices use "2", while CPE devices use "16". (Tested on WBS210 v2) Signed-off-by: Bernhard Geier <freifunk@geierb.de> [added comment about GPIO] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* tools/mkrasimage: Add support for 128k header sizeAndré Valentin2019-10-271-3/+8
| | | | | | 128k header size support is needed for ZyXEL NBG6716. Signed-off-by: André Valentin <avalentin@marcant.net>
* ar71xx: improve support for TP-Link CPE510 v2Adrian Schmutzler2019-10-211-12/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes commit bae927c551fd ("ar71xx: add support for TP-LINK CPE510 V2.0") where the support for this device wasn't optimal. Device support for the CPE510v2 so far has been a hack to enable flashing with CPE510v1 images. Those even have different hardware (e.g. additional ethernet port). With this patch, we provide proper support for this device in ar71xx. Installation: - Flash factory image through stock firmware WEB UI or through TFTP - To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. - Rename factory image to recovery.bin - Stock TFTP server IP: 192.168.0.100 - Stock device TFTP address: 192.168.0.254 Fixes: bae927c551fd ("ar71xx: add support for TP-LINK CPE510 V2.0") Signed-off-by: Andrew Cameron <apcameron@softhome.net> [Rebased onto revert commit, changed comments in mach-cpe510.c, changed commit title and description, fixed eth0 MAC address, removed eth1 initialization] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [squashed revert, added fixes tag] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* tplink-safeloader: fix compilation warningsIlya Gordeev2019-10-191-12/+13
| | | | Signed-off-by: Ilya Gordeev <Mirraz@users.noreply.github.com>
* ath79: add support for TP-Link CPE220 v2Adrian Schmutzler2019-08-071-1/+41
| | | | | | | | | | | | | | | | | | | | | | | | | This seems to be identical to CPE210 v1 despite having removable antennas. Specifications: * SoC: Qualcomm Atheros AR9344 (560 MHz) * RAM: 64MB * Storage: 8 MB * Wireless: 2.4GHz N based built into SoC 2x2 * Ethernet: 2x 100/10 Mbps, integrated into SoC, 24V POE IN Installation: Flash factory image through stock firmware WEB UI or through TFTP: To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP address:192.168.0.254 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* tplink-safeloader: increase kernel partition for CPE/WBSx10v1Adrian Schmutzler2019-08-071-8/+8
| | | | | | | | | | | | | This is a preparation for ath79 support of the CPE210/CPE510 v1. Kernel size is chosen equal to the latest update for CPE610 v1. This also updates the partition size in ar71xx target, so code remains consistent if someone looks up the device. Since CPE210, CPE510, WBS210 and WBS510 (all v1) share the same partition layout definition, and are on deprecated target anyway, this changes them all at once. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* firmware-utils: uimage_padhdr: fix Coverity issuePetr Štetiar2019-08-041-12/+12
| | | | | | | | | | | | | | | | | | | Fixes following issue reported by Coverity scan: *** CID 1452085: Security best practices violations (TOCTOU) /tools/firmware-utils/src/uimage_padhdr.c: 100 in main() 94 95 if (!infname || !outfname) { 96 usage(argv[0]); 97 exit(1); 98 } 99 >>> CID 1452085: Security best practices violations (TOCTOU) >>> Calling function "stat" to perform check on "infname". 100 if (stat(infname, &statbuf) < 0) { Fixes: a1c6a316d299 ("ramips: add support for Fon FON2601") Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for Fon FON2601NOGUCHI Hiroshi2019-07-261-0/+157
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FON2601 is a wireless router. Specification: - SoC: Mediatek MT7620A (580MHz) - RAM: 128 MiB - ROM: 16 MiB SPI Flash - Wireless: for 11b/g/n (upto 300 Mbps): MT7620A built-in WMAC for 11a/n/ac (upto 867 Mbps): MT7662E - Ethernet LAN: 1 port, upto 100 Mbps - Ethernet WAN: 1 port, upto 1000 Mbps - USB: 1 port (USB 2.0 host) - LEDs: 4 (all can be controlled by SoC's GPIO) - buttons: 1 (Displayed as "WPS" on enclosure) - serial port: 57600n8 pins: Vcc(3.3V), Rx, Tx, GND (left to right, viewed from outside of board) Installation (only available via UART): 1. download sysupgrade binary image by wget command 2. write sysupgrade binary image to Flash command is: mtd write sysupgrade.bin firmware 3. reboot Important Notice: Only one button is displayed as "WPS" on enclosure. However, it is configured as "reset" (factory resetting feature). Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com> [removed unrelated openwrt-keyring revert, missing -Wall for uimage_padhdr] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* firmware-utils: mkfwimage: fix build failure on macOS with gcc 9Petr Štetiar2019-07-191-2/+3
| | | | | | | | | | | | | | | | | Fixes following errors: src/mkfwimage.c:279:8: error: format specifies type 'long' but the argument has type 'off_t' (aka 'long long') [-Werror,-Wformat] d->stats.st_size, ^~~~~~~~~~~~~~~~ src/mkfwimage.c:280:8: error: format specifies type 'long' but the argument has type 'long long' [-Werror,-Wformat] d->partition_length - d->stats.st_size); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ src/mkfwimage.c:378:6: error: format specifies type 'unsigned long' but the argument has type 'long long' [-Werror,-Wformat] d->stats.st_size - d->partition_length); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Reported-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* firmware-utils: mkfwimage: fix more errors reported by gcc-6/7/9Petr Štetiar2019-07-192-12/+14
| | | | | | | | | | | | | | | | | | | | | src/mkfwimage.c:276:8: error: format '%lld' expects argument of type 'long long int', but argument 4 has type '__off_t' {aka 'const long int'} [-Werror=format=] src/fw.h:71:36: error: format '%llu' expects argument of type 'long long unsigned int', but argument 6 has type '__off_t' {aka 'long int'} [-Werror=format=] inlined from 'main' at src/mkfwimage.c:543:12: /string_fortified.h:106:10: error: '__builtin_strncpy' output truncated before terminating nul copying 4 bytes from a string of the same length [-Werror=stringop-truncation] inlined from 'write_part' at src/mkfwimage.c:235:2, string_fortified.h:106:10: error: '__builtin_strncpy' specified bound 16 equals destination size [-Werror=stringop-truncation] inlined from 'main' at src/mkfwimage.c:477:5: string_fortified.h:106:10: error: '__builtin_strncpy' specified bound 256 equals destination size [-Werror=stringop-truncation] inlined from 'main' at src/mkfwimage.c:496:5: string_fortified.h:106:10: error: '__builtin_strncpy' specified bound 4096 equals destination size [-Werror=stringop-truncation] inlined from 'main' at src/mkfwimage.c:481:5: string_fortified.h:106:10: error: '__builtin_strncpy' specified bound 4096 equals destination size [-Werror=stringop-truncation] inlined from 'main' at src/mkfwimage.c:485:5: string_fortified.h:106:10: error: '__builtin_strncpy' specified bound 16 equals destination size [-Werror=stringop-truncation] Runtested on ath79 and UBNT Bullet M XW. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* firmware-utils: mkfwimage: fix more errorsKevin Darbyshire-Bryant2019-07-191-4/+4
| | | | | | | | | Fix 4 errors reported by gcc 9 3 mismatched format type errors 1 unused variable error Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* firmware-utils: mkfwimage: provide human readable errorPetr Štetiar2019-07-191-1/+7
| | | | | | | | | | | | | While looking at the ath25 build breakage of 19.07 images today I've encountered following error: mkfwimage -B XS5 -v [...] ath25-ubnt5-squashfs-sysupgrade.bin.new ERROR: Failed creating firmware layout description - error code: -2 Which is barely human readable and needs poking into the source code, so this patch makes the error more verbose and usable by mere mortals. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* firmware-utils: mkfwimage: enable extra compiler checks and fix themPetr Štetiar2019-07-191-5/+4
| | | | | | | Let's enforce additional automatic checks enforced by the compiler in order to catch possible errors during compilation. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add support for TP-Link CPE510-v2/v3Andrew Cameron2019-07-181-0/+85
| | | | | | | | | | | | | | | | | | | | | | | | | TP-Link CPE510-v2/v3 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on Atheros AR9344 Specifications: - Based on the same underlying hardware as the TP-Link CPE510 - Power, LAN, and 4 green LEDs - 1 10/100Mbps Shielded Ethernet Port (Passive PoE in) - Built-in 13dBi 2x2 dual-polarized directional MIMO antenna - Adjustable transmission power from 0 to 23dBm/200mw Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net> [whitespace fixes] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for TP-Link RE650 v1Georgi Vlaev2019-07-171-0/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE650 v1 is a dual-band AC2600 range extender, based on MediaTek MT7621A and MT7615E. According to the wikidevi entry for RE650 this device is identical with TP-Link RE500 as hardware. This patch supports only RE650. Hardware specification: - SoC 880 MHz - MediaTek MT7621AT - 128 MB of DDR3 RAM - 16 MB - Winbond 25Q128FVSG - 4T4R 2.4 GHz - MediaTek MT7615E - 4T4R 5 GHz - MediaTek MT7615E - 1x 1 Gbps Ethernet - MT7621AT integrated - 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2)) - 4x buttons (Reset, Power, WPS, LED) - UART header (J1) - 2:GND, 3:RX, 4:TX Serial console @ 57600,8n1 Flash instructions: Upload openwrt-ramips-mt7621-tplink_re650-v1-squashfs-factory.bin from the RE650 web interface. TFTP recovery to stock firmware: Unfortunately, I can't find an easy way to recover the RE without opening the device and using modified binaries. The TFTP upload will only work if selected from u-boot, which means you have to open the device and attach to the serial console. The TFTP update procedure does *not* accept the published vendor firmware binaries. However, it allows to flash kernel + rootfs binaries, and this works if you have a backup of the original contents of the flash. It's probably possible to create special image out of the vendor binaries and use that as recovery image. Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com> [re-added variables for kernel header] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: increase kernel partition size for CPE610v1Andrew Cameron2019-07-071-2/+2
| | | | | | | | | Increase the Kernel partition to address the issue discussed here https://forum.openwrt.org/t/cpe610-v1-sysupgrade-bin-missing-too-big/39637/5 Switch Back to the okli Loader to support increased partition size Signed-off-by: Andrew Cameron <apcameron@softhome.net> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [add <> for e-mail]
* ath79: add support for TP-Link CPE610-v1Andrew Cameron2019-06-241-0/+39
| | | | | | | | | | | | | | | | | | | | | TP-Link CPE610-v1 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on Atheros AR9344 Specifications: - Based on the same underlying hardware as the TP-Link CPE510 - Power, LAN, WLAN5G green LEDs - 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* firmware-utils: jcgimage: add support for 4MiB+ imagesDavide Fioravanti2019-05-311-5/+19
| | | | | | | | | | | | | The first version of this script allowed just 4Mb factory images. With this patch is possible to set the maximum size of the payload. For an 8Mb flash, the corresponding maxsize is: 8 * 1024 * 1024 - 5 * 64 * 1024 = 8388608 - 327680 = 8060928 If the -m argument is not set, the default maximum size will be used for backward compatibility. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* firmware-utils: jcgimage: fix style and compiler warningsDavide Fioravanti2019-05-311-48/+46
| | | | | | Fixed some compilation warnings. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* tools/firmware-utils: mktplinkfw2: add Qualcomm layoutsDavide Fioravanti2019-05-181-0/+12
| | | | | | | This commit adds the partition layout used by the TP-Link Archer D50 and probably by the TP-Link Archer D7 to mktplinkfw2. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* ipq40xx: add factory image for EnGenius ENS620EXTSteve Glennon2019-05-111-27/+177
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Extended mksenaofw to support new "capwap" header structure. This supports flashing from factory 3.0.0, 3.0.1, 3.1.0 and 3.5.5 firmware. Note that the factory image format changes for 3.1 and later firmware, and that the 3.1.0 and 3.5.5 Engenius firmware will refuse the factory_30.bin file. Similarly, the 3.0.0 and 3.0.1 Engenius firmware will refuse the factory_35.bin file. Flashing from the Engenius 3.1.0 firmware with the factory_35.bin firmware has not been tested, as 3.1.0 firmware (Engenius "middleFW") is only intended as part of the upgrade path to 3.5.5 firmware. Modified ipq40xx image Makefile to appropriately invoke mksenaofw with new parameters to configure the capwap header. Note that there is currently no method to return to factory firmware, so this is a one-way street. Path from factory 3.0.0 and 3.0.1 (EnGenius) software to OpenWrt is to navigate to 192.168.1.1 on the stock firmware and navigate to the firmware menu. Then copy the URL you have for that page, something like http://192.168.1.1/cgi-bin/luci/;stok=12345abcdef/admin/system/flashops and replace the trailing /admin/system/flashops with just /easyflashops You should then be presented with a simple "Firmware Upgrade" page. On that page, BE SURE TO CLEAR the "Keep Settings:" checkbox. Choose the openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_30.bin, click "Upgrade" and on the following page select "Proceed". Path from factory 3.5.5 (EnGenius) software to OpenWrt is simply to use the stock firmware update menu. Choose the openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_35.bin and click "Upload" and "Proceed". The device should then flash the OpenWrt firmware and reboot. Note that this resets the device to a default configuration with Wi-Fi disabled, LAN1/PoE acting as a WAN port (running DHCP client) and LAN2 acting as a LAN port with a DHCP server on 192.168.1.x (AP is at 192.168.1.1) Signed-off-by: Steve Glennon <s.glennon@cablelabs.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [sorry, for unfixing the 80-lines eyesores.]