aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
...
* x86: DRM: add x64 subtarget supportLucian Cristian2019-02-172-4/+117
| | | | | | copy settings from generic subtarget Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* x86: video: disable builtin radeon DRM driverLucian Cristian2019-02-172-2/+2
| | | | | | | builtin driver can't access the /lib/firmware while booting, module driver will be able to read and load the firmware files Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* kernel: disable CONFIG_USB_IMX21_HCD in default for kernel 4.14Yangbo Lu2019-02-173-1/+2
| | | | | | | | | | | CONFIG_USB_IMX21_HCD should be handled in generic config and module package. So moved it into generic config. This also fixed build issue (kernel config question) of layerscape armv8_32b since it also used ARCH_MXC. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> [Deactivate CONFIG_USB_IMX21_HCD also for kernel 4.19] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: fix: A64 unstable timerOskari Lemmela2019-02-177-0/+660
| | | | | | | | Backport A64 unstable timer patches from linux 5.1 Signed-off-by: Oskari Lemmela <oskari@lemmela.net> [Split the single patch into the two original patches] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: add support for Sinovoip Banana Pi M2 PlusPawel Dembicki2019-02-172-1/+12
| | | | | | | | | | | | | | | | | | | CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K @ 1.2 Ghz GPU: Mali400MP2 GPU @ 600MHz (supports OpenGL ES 2.0) Memory: 1GB DDR3 (shared with GPU) Onboard: Storage TF card (Max. 64GB) / MMC card slot Onboard: Network 10/100M Ethernet RJ45 (Realtek RTL8211E) Onboard: Network BT4.0/WiFi 802.11 b/g/n (Ampak AP6212) Onboard header: SPI, I2C, GPIO, UART USB 2.0: Two USB 2.0 HOST, One USB 2.0 OTG Untested: Audio, Video Not working: Bluetooth Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* x86: image: add test module to bootloaderTomasz Maciej Nowak2019-02-171-2/+2
| | | | | | | | | | | | It was previously added in 546fced, which was part of "intel-microcode: load as early as possible" series. Unfortunately the conditionals added to GRUB config caused error on boot, because on sysupgrade, bootloader is not updated and is left with old features/modules. Since this module is needed for early microcode load and transition to this needs to be done step by step, enable the test module now, so that every newly created image has it already embedded. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* build: remove leftovers from previous x86 commitsTomasz Maciej Nowak2019-02-172-9/+1
| | | | | | | | | | | | | | | | | VBoxManage is not used and the image is created with proper permisions: 0f5d0f6 image: use internal qemu-img for vmdk and vdi images drop host dependencies on qemu-utils and VirtualBox Unreachable config symbols: 9e0759e x86: merge all geode based subtargets into one No need to define those symbols since x86_64 is subtarget of x86: 196fb76 x86: make x86_64 a subtarget instead of a standalone target Unreachable config symbols, so remove GRUB_ROOT: 371b382 x86: remove the xen_domu subtarget Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ar71xx: Fix 5 GHz MAC address for Archer C60 v2Adrian Schmutzler2019-02-171-1/+6
| | | | | | | | Looks like C60 v2 needs the MAC address to be calculated manually, while the C60 v1 gets it correctly without manual interference. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: Remove CONFIG_UDF_NLS for kernel 4.19Rosen Penev2019-02-171-1/+0
| | | | | | kernel 4.18 removed the symbol and made NLS implicit. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* kernel: bump 4.19 to 4.19.23Koen Vandeputte2019-02-157-15/+15
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.101Koen Vandeputte2019-02-151-1/+1
| | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-3819 Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ipq40xx: fix ipq40xx_setup_macs for Linksys EA6350v3Oever González2019-02-141-1/+1
| | | | | | | | | | | | | This commit fixes the script that sets the MAC address of the LAN switch. The LAN MAC address should be the WAN MAC address plus one. Without this patch the WAN and the LAN interface will use the same MAC address and an error will be generated. With this patch all interfaces will have a different MAC address, consecutive in the following order: WAN, LAN, radio0 and radio1. Signed-off-by: Oever González <notengobattery@gmail.com>
* ipq8064: Enabling sata port ipq8064 based devicesRoman Glova2019-02-141-0/+2
| | | | | | | | | | | | | | | | | | | | | | (original text here: https://patchwork.kernel.org/patch/8686761/) On some SOCs PORTS_IMPL register value is never programmed by the BIOS and left at zero value. Which means that no sata ports are avaiable for software. AHCI driver used to cope up with this by fabricating the port_map if the PORTS_IMPL register is read zero, but recent patch broke this workaround as zero value was valid for nvme disks. This patch adds ports-implemented dt bindings as workaround for this issue in a way that DT can dictate the port_map incase where the SOCs does not program it already. This patch is equal to commits: 67f8425d0ee1 ("ipq8064: dts: force AP148 SATA port mapping") 2e7a2c91019c ("ARM: dts: qcom: Move common nodes to ipq8064-v.1.0.dtsi") in the upstream linux kernel. Signed-off-by: Roman Glova <roman_glova@epam.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added upstream commits, reorg' commit message]
* ath79: add support for I-O DATA WN-AC1600DGRINAGAKI Hiroshi2019-02-148-16/+84
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC1600DGR is a 2.4/5 GHz band 11ac router, based on Qualcomm Atheros QCA9557. Specification: - SoC: Qualcomm Atheros QCA9557 - RAM: 128 MB - Flash: 16 MB - WLAN: 2.4/5 GHz - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 3T3R (QCA9880) - Ethernet: 5x 10/100/1000 Mbps - Switch: QCA8337N - LED/key: 6x/6x(4x buttons, 1x slide switch) - UART: through-hole on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port of WN-AC1600DGR 2. Connect power cable to WN-AC1600DGR and turn on it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Alternative flash instruction using initramfs image: 1. Prepare a computer and TFTP server software with the IP address "192.168.99.8" and renamed OpenWrt initramfs image "uImageWN-AC1600DGR" 2. Connect between WN-AC1600DGR and the computer with UART 3. Connect power cable to WN-AC1600DGR, press "4" on the serial console and enter the U-Boot console 4. execute "tftpboot" command on the console and download initramfs image from the TFTP server 5. execute "bootm" command and boot OpenWrt 6. On initramfs image, download the sysupgrade image to the device and perform sysupgrade with it 7. Wait ~150 seconds to complete flashing This commit also removes unnecessary "qca,no-eeprom" property from the ath10k wifi node. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: fix qca955x dual pci resource allocationSantiago Piccinini2019-02-141-1/+1
| | | | | | | | Tested with a dual pci QCA9558 board (LibreRouter v1) in three configurations: enabling pcie0 only, pcie1 only and both enabled. Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed ML notice]
* ath79: fix qca955x pcie0 memory sizeSantiago Piccinini2019-02-141-1/+1
| | | | | | | | | Datasheet states that both PCI ranges are of 0x2000000 size: 0x1000_0000-0x11FF_FFF and 0x1200_0000-0x13FF_0000. Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net> Reviewed-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed ML notice]
* ipq40xx: add support for ASUS LyraMarius Genheimer2019-02-1410-6/+652
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: Qualcomm IPQ4019 (Dakota) 717 MHz, 4 cores RAM: 256 MiB (Nanya NT5CC128M16IP-DI) FLASH: 128 MiB (Macronix NAND) WiFi0: Qualcomm IPQ4019 b/g/n 2x2 WiFi1: Qualcomm IPQ4019 a/n/ac 2x2 WiFi2: Qualcomm Atheros QCA9886 a/n/ac BT: Atheros AR3012 IN: WPS Button, Reset Button OUT: RGB-LED via TI LP5523 9-channel Controller UART: Front of Device - 115200 N-8 Pinout 3.3v - RX - TX - GND (Square is VCC) Installation: 1. Transfer OpenWRT-initramfs image to the device via SSH to /tmp. Login credentials are identical to the Web UI. 2. Login to the device via SSH. 3. Flash the initramfs image using > mtd-write -d linux -i openwrt-image-file 4. Power-cycle the device and wait for OpenWRT to boot. 5. From there flash the OpenWRT-sysupgrade image. Ethernet-Ports: Although labeled identically, the port next to the power socket is the LAN port and the other one is WAN. This is the same behavior as in the stock firmware. Signed-off-by: Marius Genheimer <mail@f0wl.cc> [Dropped setup_mac 02_network in favour of 05_set_iface_mac_ipq40xx.sh, reorderd 02_network entries, added board.bin WA for the QCA9886 from ath79, minor dts touchup, added rng to 4.19 dts] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: ea6350v3: 4.19: enable pseudo rng supportChristian Lamparter2019-02-141-0/+4
| | | | | | | Robert Marko made a big effort to enable the rng on all ipq40xx for 4.19, so let's continue the quest. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* gemini: Name binary "bootpart.tar.gz"Linus Walleij2019-02-141-2/+2
| | | | | | | | | | This factory binary i supposed to actually be unzipped and untarred by the user as part of the installation process (this NAS boots from harddisk), so name it "bootpart.tar.gz" and not "factory.bin" so it is helpful for users. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: Add missing config option for kernel 4.19Daniel Engberg2019-02-141-0/+1
| | | | | | Add CONFIG_USB_ROLE_SWITCH otherwise Octeon 4.19 fails compile Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* mpc85xx: 4.19: add missing symbolPawel Dembicki2019-02-141-0/+1
| | | | | | | | OCEDO Panda was added in b368373f, but only for 4.14 config. This patch fix 4.19 build for generic and p2020 subtarget. Signed-off-by: Pawel Dembicki <p.dembicki@wb.com.pl>
* ramips: change status LED for Buffalo WHR-G300NINAGAKI Hiroshi2019-02-141-6/+5
| | | | | | | | | | | Buffalo WHR-G300N has a LED for power status indication, but it is not connected to the GPIO and cannot be controlled by the kernel. So, WHR-G300N uses "ROUTER" LED as the system status LED instead. This commit changes it to use "DIAG" LED insted of "ROUTER" like WHR-G301N in ath79 target. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: various Netgear R6120 fixesDavid Bauer2019-02-143-12/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The R6120 has no 5GHz WLAN LED, the assigned GPIO in fact controls the WAN LED. Renames the LED accordingly in the device-tree. Removes the 5GHz WLAN LED trigger. Adds the correct WAN port LED trigger. ---- Currently, the MAC address for the Netgear R6120 is read from the NVRAM partition. The offset for the MAC address however is not consistent across devices or firmware versions. Switch to using the factory partition like all other Netgear devices do. ---- The LAN ports of the R6120 are labled in reverse on the casing. Adjust LuCI switchport numbering accordingly. ---- The WiFi eeprom offsets for the R6120 are currently wrong (5GHz offset is bigger than the partition itself). Fixes poor performance on 2.4 and 5 GHz. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for I-O DATA WN-AC1167GRINAGAKI Hiroshi2019-02-144-0/+258
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC1167GR is a 2.4/5 GHz band 11ac router, based on MediaTek MT7620A. Specification: - SoC : MediaTek MT7620A - RAM : DDR2 64 MB - Flash : SPI-NOR 8MB - WLAN : 2.4/5 GHz, 2T2R - 2.4 GHz: MT7620A (SoC) - 5 GHz : MT7612E - Ethernet: 10/100/1000 Mbps (ext. MT7530) - LED/key : 4x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J2: TX, GND, RX, Vcc from SoC side - 115200n8 Flash instruction using factory image: 1. Boot WN-AC1167GR normaly 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: proper indentation in image/common-tp-link.mkPaul Wassi2019-02-141-1/+1
| | | | | | Add two spaces for proper indentation in image/common-tp-link.mk Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: fix port order on TL-WR841ND-v7Paul Wassi2019-02-141-3/+3
| | | | | | | | The switch ports are seen one to one on the case. Also remove unneeded secondary port numbers in this case statement. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: change ledtrig on GL.iNet AR150Paul Wassi2019-02-141-1/+1
| | | | | | | | | Change the ledtrig for LAN from netdev to switch. Although eth1 comes out of the device at a single port, this port is a switch-port and therefore the LED must be triggered by that. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: rename TP-LINK to TP-LinkPaul Wassi2019-02-146-34/+34
| | | | | | Remove inconsistencies in the vendor's name. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ar71xx: fix TL-MR3220-v2 switch port orderPaul Wassi2019-02-141-1/+1
| | | | | | | Fix the switch port order for proper display on high level interfaces. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ar71xx: fix TL-WR741ND-v4 switch port orderPaul Wassi2019-02-141-1/+5
| | | | | | | Fix the switch port order for proper display on high level interfaces. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: rename TL-WR740ND-v4 to TL-WR740N-v4Paul Wassi2019-02-144-7/+7
| | | | | | Give the device the same name it had in ar71xx. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: fix TL-WR741ND-v4 switch port orderPaul Wassi2019-02-141-1/+1
| | | | | | | Fix the switch port order for proper display on high level interfaces. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* kernel: bump 4.19 to 4.19.21Koen Vandeputte2019-02-145-79/+13
| | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 0007-ARM-dts-Fix-up-the-D-Link-DIR-685-MTD-partition-info.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.99Koen Vandeputte2019-02-1432-119/+69
| | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 950-0434-mmc-bcm2835-Recover-from-MMC_SEND_EXT_CSD.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.156Koen Vandeputte2019-02-142-7/+7
| | | | | | | | | Refreshed all patches. Compile-tested on: ar7 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: enable CONFIG_BPF_JIT by defaultTony Ambardar2019-02-113-3/+3
| | | | | | | | | | | | | | | | | | Enable the built-in BPF JIT compiler for all 4.9, 4.14 and 4.19 kernels, which should speed up cBPF and eBPF-based packet filtering (tc, iptables) and packet sniffing (libpcap, tcpdump, fwknopd, etc). This has minimal kernel size impact, increasing the size of uImage-lzma (normally ~2 MB on mips_24kc or mips64el_mips64) by 5 KB for the MIPS32 arch cBPF JIT and by 9 KB for the MIPS64 arch eBPF JIT, on kernel 4.14. With JIT enabled (cBPF only), the standard BPF test module (test_bpf.ko) running on a DIR-835 (mips_24kc) used 33 CPU seconds, but 68 without JIT. This change aligns with the notion of OpenWRT as the network go-to swiss army knife for packet handling, especially on CPU-constrained platforms. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ath79: add support for Xiaomi Mi Router 4QDavid Bauer2019-02-113-0/+165
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9561 RAM: 64M DDR2 FLASH: 16M SPI-NOR ETH: 1x WAN - 2x LAN WiFi: QCA9561 3T3R BTN: 1x Reset - 1x WPS LED: 1x Blue - 1x Red - 1x Yellow UART: TX - GND - RX - VCC (From ethernet port) 115200n8 - 3.3V Installation ------------ 1. Connect to the device via UART. 2. Interrupt the U-Boot on power-on by pressing enter when prompted. 3. Connect you computer to one of the routers LAN ports. Assign yourself the IP 192.168.31.10/24. Copy the OpenWRT initramfs image to a tftp server root directory. Rename the image to 'x4q.bin'. 4. Load the initramfs image to the router by executing following command in U-Boot. The image will boot afterwards. > tftpboot 0x81000000 x4q.bin; bootm 5. SCP the sysupgrade-image into '/tmp'. Remember to assign yourself an IP in 192.168.1.0/24 for this step! 6. Install OpenWRT permanently by executing > sysupgrade -n /tmp/<OpenWRT-sysupgrade-image> Signed-off-by: David Bauer <mail@david-bauer.net>
* gemini: Fix kmod-led-trig-heartbeat typoLinus Walleij2019-02-111-1/+1
| | | | | | | | It's kmod-ledtrig-* not kmod-led-trig-*. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> [extended subject] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ar71xx: add rssileds for xw devicesKoen Vandeputte2019-02-111-0/+1
| | | | | | | | | | | Commit 7ebbbda29377 ("ar71xx: ubnt-(xm,xw): fix LED RSSI indication") adds support for using the RSSI strenght via LEDS. The rssileds package addition got lost during altering the patch. Add it again to fix this. Fixes: 7ebbbda29377 ("ar71xx: ubnt-(xm,xw): fix LED RSSI indication") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: fold xt_FLOWOFFLOAD fixes into the main patchFelix Fietkau2019-02-093-144/+37
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* netfilter: fix checking method of conntrack helperHsiuWen Yen2019-02-091-0/+51
| | | | | | | | | | | | | | | | This patch uses nfct_help() to detect whether an established connection needs conntrack helper instead of using test_bit(IPS_HELPER_BIT, &ct->status). The reason for this modification is that IPS_HELPER_BIT is only set when the conntrack helper is attached by explicit CT target. However, in the case that a device enables conntrack helper via the other ways (e.g., command "echo 1 > /proc/sys/net/netfilter/nf_conntrack_helper") , the status of IPS_HELPER_BIT will not present any change. That means the IPS_HELPER_BIT might lose the checking ability in the context. Signed-off-by: HsiuWen Yen <y.hsiuwen@gmail.com>
* ar71xx: ubnt-(xm,xw): fix LED RSSI indicationLech Perczak2019-02-082-5/+6
| | | | | | | | | | | | | | | | | When mapping for RSSI LEDs was defined for interface wlan0 on Ubiquiti XM and XW family, it missed connection to actual interface. Therefore create the mapping to interface, so RSSI LEDs work without additional configuration, after starting rssileds service. Also add the required package for this. While at that, remove coefficients needed for PWM LEDs, as XM and XW boards do not support PWM LEDs. Tested-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Lech Perczak <lech.perczak@gmail.com> [Squashed commits + remove custom device_packages + slighty rewrite the commit msg] Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: fix RB941-2nD detectionJulien Rabier2019-02-081-1/+1
| | | | | | | | | | | | Some hAP lite routers aren't detected because /proc/cpuinfo shows "RouterBOARD RB941-2nD" instead of "RouterBOARD 941-2nD". Fix that. Signed-off-by: Julien Rabier <taziden@flexiden.org> [Alter string to include all flavours + slight rewrite of commit msg] Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: fix Arduino Yun enabling of level shifters outputsEdoardo Scaglia2019-02-081-2/+2
| | | | | | | | | | | | | | | As show in Arduino Yun schematic [1] GPIO 21 and 22 are connected to output enable pin (OE) of two NTB01xx level shifters. NTB01xx datasheets [2] [3] states that OE pin are active-high therefore we should initialize GPIO 21 (DS_GPIO_OE) and GPIO 22 (DS_GPIO_OE2) accordingly to actually enable level shifters outputs. [1] https://www.arduino.cc/en/uploads/Main/arduino-Yun-schematic.pdf [2] https://www.nxp.com/docs/en/data-sheet/NTB0102.pdf [3] https://www.nxp.com/docs/en/data-sheet/NTB0104.pdf Signed-off-by: Edoardo Scaglia <edoardo.87@gmail.com>
* kernel: add missing symbols to 4.19Petr Štetiar2019-02-081-0/+10
| | | | | | | | | | | | While preparing 4.19 for imx6 and test building it with CONFIG_ALL_KMODS=y with verbose mode enabled, I was asked by kernel config about few missing symbols/modules Let's add them to the generic config. Signed-off-by: Petr Štetiar <ynezz@true.cz> [slight rewrite of commit log] Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.20Koen Vandeputte2019-02-083-82/+8
| | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 100-arm-cns3xxx-fix-writing-to-wrong-PCI-registers-after.patch Altered patches: - 721-phy_packets.patch Compile-tested on: imx6 Runtime-tested on: imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.98Koen Vandeputte2019-02-086-87/+13
| | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 100-arm-cns3xxx-fix-writing-to-wrong-PCI-registers-after.patch Altered patches: - 721-phy_packets.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.155Koen Vandeputte2019-02-085-84/+10
| | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 100-arm-cns3xxx-fix-writing-to-wrong-PCI-registers-after.patch Altered patches: - 721-phy_packets.patch Compile-tested on: ar7 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: ag71xx: Fix tx queue timeouts during ifupPetr Štetiar2019-02-071-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On ath79 and UBNT Bullet M XW (ar9342) I was experiencing weird issues during network setup[1] which I was able to reproduce easily with following commands: uci set network.lan.ipaddr='192.168.1.20' uci commit network ifup lan Which resulted after some time in: ... WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:461 dev_watchdog+0x16c/0x280 NETDEV WATCHDOG: eth0 (ag71xx): transmit queue 0 timed out ... Sometimes I wasn't able to use networking anymore, sometimes it was enough to just ifdown/ifup lan and network was backup. On ar71xx it was all working just fine. I've found out, that it was happening because ag71xx_poll() wasn't called, thus the TX queue wasn't emptied. The ag71xx_poll() is being called from napi hrtimer, which is enabled by napi_schedule() in ar71xx_interrupt(), but since no interrupts were ever fired again after ag71xx_stop() was called, it was always leading to tx queue timeouts: *** ag71xx_hard_start_xmit() eth0: packet injected into TX queue eth0: raw intr=00000001 TXPS POLL eth0: enable polling mode eth0: processing TX ring, flush=no eth0: disable polling mode, rx=1, tx=1,limit=32 ( `ifup lan done here` ) *** ag71xx_stop() *** ag71xx_open() *** ag71xx_hw_enable() IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready *** ag71xx_hard_start_xmit() eth0: packet injected into TX queue *** ag71xx_hard_start_xmit() eth0: packet injected into TX queue ... WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:320 dev_watchdog+0x164/0x274 So I've looked at ag71xx_stop() in ar71xx, added the missing bits to ath79 and fixed this issue. 1. https://github.com/openwrt/openwrt/pull/1635#issuecomment-448638246 Signed-off-by: Petr Štetiar <ynezz@true.cz> [move ag->link before ag71xx_hw_disable to retain ordering as original] Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: rename symbol in kernel 4.19 configKoen Vandeputte2019-02-071-1/+1
| | | | | | | | A symbol was renamed upstream starting from kernel 4.18 [1] Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> [1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?h=v5.0-rc5&id=34b13e5e4641c0e9e0aad471a6d8dfb7999276f1
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-24 17:50:35 +0000