aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* bmips: dgnd3700v2: fix network configÁlvaro Fernández Rojas2022-05-231-0/+1
| | | | | | | ucidef_set_bridge_device is needed for DGND3700v2 network config since VLAN 1 must be used for the switch to be correctly configured. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm27xx: add pwm-fan dependency to RPi PoEÁlvaro Fernández Rojas2022-05-221-1/+1
| | | | | | This is needed for the fan in the PoE hat to work. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* realtek: replace RTL93xx GPIO patchesSander Vanheule2022-05-224-64/+234
| | | | | | | | | | | Patches to support the SoC's GPIO controller for RTL930x and RTL931x devices have been accepted upstream. Replace the current preliminary patch with the upstream ones, excluding devictree binding changes. The updated patches add GPIO IRQ balancing support on RTL930x, but this cannot be used until these devices also support SMP. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* mediatek: mt7622: add support for ELECOM WRC-X3200GST3INAGAKI Hiroshi2022-05-214-5/+464
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-X3200GST3 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on MT7622B. Specifications: - SoC : MediaTek MT7622B - RAM : DDR3 512 MiB (Nanya NT5CC256M16ER-EK) - Flash : SPI-NAND 128 MiB (Winbond W25N01GVZEIG) - WLAN : 2.4/5 GHz 4T4R - 2.4 GHz : MediaTek MT7622B (SoC) - 5 GHz : MediaTek MT7915A - Ethernet : 5x 10/100/1000 Mbps - Switch : MediaTek MT7531 - LEDs/Keys : 6x/4x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J19: 3.3V, GND, TX, RX from power jack side - 115200n8 - Power : 12 VDC, 1.5 A Flash instruction using factory image: 1. Boot WRC-X3200GST3 normally with "Router" mode 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button 4. Wait ~120 seconds to complete flashing MAC Addresses: LAN : 04:AB:18:xx:xx:77 (Factory, 0x7FFF4 (hex)) WAN : 04:AB:18:xx:xx:78 (Factory, 0x7FFFA (hex)) 2.4 GHz: 04:AB:18:xx:xx:79 (Factory, 0x4 (hex)) 5 GHz : 04:AB:18:xx:xx:7A (none) Note: - currently, there is no "phy1tpt" trigger for 5 GHz wlan (MT7915) in "trigger" file of LEDs, use "phy1radio" trigger instead Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: NanoBeam M5 fix target_devicesJan-Niklas Burfeind2022-05-212-2/+2
| | | | | | | | | | Update the name of for the Ubiquiti NanoBeam M5 to match the auto-generated one at runtime. Otherwise sysupgrade complains about mismatching device names. This also required renaming the DTS. Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
* ath79: add support for Ubiquiti NanoBeam M5Jan-Niklas Burfeind2022-05-212-0/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ubiquiti NanoBeam M5 devices are CPE equipment for customer locations with one Ethernet port and a 5 GHz 300Mbps wireless interface. Specificatons: - Atheros AR9342 - 535 MHz CPU - 64 MB RAM - 8 MB Flash - 1x 10/100 Mbps Ethernet with passive PoE input (24 V) - 6 LEDs of which four are rssi - 1 reset button - UART (4-pin) header on PCB Notes: The device was supported by OpenWrt in ar71xx. Flash instructions (web/ssh/tftp): Loading the image via ssh vias a stock firmware prior "AirOS 5.6". Downgrading stock is possible. * Flashing is possible via AirOS software update page: The "factory" ROM image is recognized as non-native and then installed correctly. AirOS warns to better be familiar with the recovery procedure. * Flashing can be done via ssh, which is becoming difficult due to legacy keyexchange methods. This is an exempary ssh-config: KexAlgorithms +diffie-hellman-group1-sha1 HostKeyAlgorithms ssh-rsa PubkeyAcceptedKeyTypes ssh-rsa User ubnt The password is ubnt. Connecting via IPv6 link local worked best for me. 1. scp the factory image to /tmp 2. fwupdate.real -m /tmp/firmware_image_file.bin -d * Alternatively tftp is possible: 1. Configure PC with static IP 192.168.1.2/24. 2. Enter the rescue mode. Power off the device, push the reset button on the device (or the PoE) and keep it pressed. Power on the device, while still pushing the reset button. 3. When all the leds blink at the same time, release the reset button. 4. Upload the firmware image file via TFTP: tftp 192.168.1.20 tftp> bin tftp> trace Packet tracing on. tftp> put firmware_image.bin Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
* ath79: add support for MikroTik hAP (RB951Ui-2nD)Maciej Krüger2022-05-216-0/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The MikroTik hAP (product code RB951Ui-2nD) is an indoor 2.4Ghz AP with a 2 dBi integrated antenna built around the Atheros QCA9531 SoC. Specifications: - SoC: Atheros QCA9531 - RAM: 64 MB - Storage: 16 MB NOR - Winbond 25Q128FVSG - Wireless: Atheros QCA9530 (SoC) 802.11b/g/n 2x2 - Ethernet: Atheros AR934X switch, 5x 10/100 ports, 10-28 V passive PoE in port 1, 500 mA PoE out on port 5 - 8 user-controllable LEDs: · 1x power (green) · 1x user (green) · 4x LAN status (green) · 1x WAN status (green) · 1x PoE power status (red) See https://mikrotik.com/product/RB951Ui-2nD for more details. Notes: The device was already supported in the ar71xx target. Flashing: TFTP boot initramfs image and then perform sysupgrade. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Signed-off-by: Maciej Krüger <mkg20001@gmail.com>
* ath79: add support for MikroTik RouterBOARD hAP ac liteThibaut VARÈNE2022-05-217-0/+142
| | | | | | | | | | | | | | | | | | | | | | | | | | | The MikroTik RB952Ui-5ac2nD (sold as hAP ac lite) is an indoor 2.4Ghz and 5GHz AP/router with a 2 dBi integrated antenna. See https://mikrotik.com/product/RB952Ui-5ac2nD for more details. Specifications: - SoC: QCA9533 - RAM: 64MB - Storage: 16MB NOR - Wireless: QCA9533 802.11b/g/n 2x2 / QCA9887 802.11a/n/ac 2x2 - Ethernet: AR934X switch, 5x 10/100 ports, 10-28 V passive PoE in port 1, 500 mA PoE out on port 5 - 6 user-controllable LEDs: - 1x user (green) - 5x port status (green) Flashing: TFTP boot initramfs image and then perform sysupgrade. The "Internet" port (port number 1) must be used to upload the TFTP image, then connect to any other port to access the OpenWRT system. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* bcm27xx: sound-soc-rpi-cirrus: fix packageÁlvaro Fernández Rojas2022-05-201-2/+4
| | | | | | Fix kmod-sound-soc-rpi-cirrus package dependencies. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: add linux v5.15 supportÁlvaro Fernández Rojas2022-05-20133-0/+20886
| | | | | | | | Build system: x86_64 Build-tested: generic, smp Run-tested: generic/AR-5387un, smp/VR-3032u Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm27xx: modules: video: fix whitespaceÁlvaro Fernández Rojas2022-05-201-1/+1
| | | | | | No idea how this ended up here v2... Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm27xx: enable PWM drivers in configÁlvaro Fernández Rojas2022-05-205-18/+18
| | | | | | Removes PWM module package. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: rework ARCH_HAS_SYNC_DMA_FOR_CPU_ALL patchÁlvaro Fernández Rojas2022-05-201-25/+39
| | | | | | Let's disable ARCH_HAS_SYNC_DMA_FOR_CPU_ALL only for BCM6358. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: remove linux 5.10 compatibilityÁlvaro Fernández Rojas2022-05-2062-9491/+0
| | | | | | | A devent amount of patches have been upstreamed, so maintaining linux 5.10 on this target makes no sense. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: switch to linux 5.15Álvaro Fernández Rojas2022-05-201-2/+1
| | | | | | | I tested it locally and I couldn't find any regressions, so let's give this a wider test :). Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: add linux v5.15 supportÁlvaro Fernández Rojas2022-05-2026-4/+1894
| | | | | | | | Build system: x86_64 Build-tested: generic, nand Run-tested: generic/AR-5387un, nand/VR-3032u Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm27xx: base-files: align network filesÁlvaro Fernández Rojas2022-05-192-4/+6
| | | | | | | | - Use the same order for /etc/board.d/02_network and /lib/preinit/05_set_preinit_iface_brcm2708. - Add missing RPi 400 and CM4 to /lib/preinit/05_set_preinit_iface_brcm2708. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm27xx: diag.sh: fix whitespaceÁlvaro Fernández Rojas2022-05-191-1/+1
| | | | | | No idea how this ended up here... Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ipq40xx: mikrotik: dont include ath10k-board-qca4019 by defaultRobert Marko2022-05-191-0/+1
| | | | | | | | | | | Since MikroTik subtarget now uses dynamic BDF loading its crucial that it doesnt include the board-2.bin at all which is provided by the ath10k-board-qca4019 package. So to resolve this dont include the ath10k-board-qca4019 package on the MikroTik subtarget. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq-wifi: remove packaged BDF-s for MikroTik devicesRobert Marko2022-05-191-6/+4
| | | | | | | | | | | Since we now provide the BDF-s for MikroTik IPQ40xx devices on the fly, there is noneed to include package and ship them like we do now. This also resolves the performance issues that happen as MikroTik changes the boards and ships them under the same revision but they actually ship with and require a different BDF. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: mikrotik: provide BDF-s on demandRobert Marko2022-05-191-0/+23
| | | | | | | | | | | Since we now can pass the API 1 BDF-s aka board.bin to the ath10k driver per radio lets use that to provide the BDF-s for MikroTik devices. This also resolves the performance issues that happen as MikroTik changes the boards and ships them under the same revision but they actually ship with and require a different BDF. Signed-off-by: Robert Marko <robimarko@gmail.com>
* config: limit CONFIG_DEBUG_INFO to top-level generic configsTony Ambardar2022-05-1818-19/+0
| | | | | | | | | | Remove redundant target-level entries, noting that these settings will be configured from "Kernel build options" of Kconfig. Signed-off-by: Tony Ambardar <itugrok@yahoo.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> [remove from new configs introduced after patch submission] Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: add DEBUG_INFO_REDUCED config optionStijn Tintel2022-05-182-2/+0
| | | | | | | | Add DEBUG_INFO_REDUCED as a kernel config option and remove it from the kernel configs. This is in preparation of the upcoming option to enable BTF typeinfo, which is incompatible with DEBUG_INFO_REDUCED. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* layerscape/armv8_64b: enable DEBUG_INFO_REDUCEDStijn Tintel2022-05-181-1/+0
| | | | | | | | | | | | | We currently enable DEBUG_INFO_REDUCED for all targets via the generic kernel config. There is only one subtarget, layerscape/armv8_64b, that overrides this setting. As there is no explanation for this in the commit message that introduced this, and question to its author went unanswered, let's simply drop this symbol from the subtarget config. This way, we have consistency across the tree, and we do not have to introduce a special case when moving this symbol to an OpenWrt kernel config option. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: backport build fix for tools/resolve_btfidsStijn Tintel2022-05-182-0/+108
| | | | | | | Building tools/resolve_btfids requires libelf and zlib. Without this build fix, the kernel build system will not find these dependencies. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* bcm27xx: add CPU_FREQ_GOV_SCHEDUTILJohn Audia2022-05-173-0/+7
| | | | | | | | | This is enabled upstream for bcm2709, bcm2710 and bcm2711. https://github.com/raspberrypi/linux/blob/dff79e31c3b05a50f725442c1fc19a6194491523/arch/arm/configs/bcm2709_defconfig#L51 https://github.com/raspberrypi/linux/blob/dff79e31c3b05a50f725442c1fc19a6194491523/arch/arm/configs/bcm2711_defconfig#L51 Signed-off-by: John Audia <graysky@archlinux.us> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm27xx: remove linux 5.10 configsÁlvaro Fernández Rojas2022-05-174-1721/+0
| | | | | | Sorry, I missed these when removing linux v5.10 support... Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm27xx: remove linux 5.10 compatibilityÁlvaro Fernández Rojas2022-05-17718-220355/+2
| | | | Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm27xx: switch to 5.15Álvaro Fernández Rojas2022-05-171-2/+1
| | | | | | | I tested it locally and I couldn't find any regressions, so let's give this a wider test :). Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm27xx: add support for linux v5.15Álvaro Fernández Rojas2022-05-17924-1/+265734
| | | | | | | | | Build system: x86_64 Build-tested: bcm2708, bcm2709, bcm2710, bcm2711 Run-tested: bcm2708/RPiB+, bcm2709/RPi3B, bcm2710/RPi3B, bcm2711/RPi4B Signed-off-by: Marty Jones <mj8263788@gmail.com> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: Add missing devm_regulator_get_exclusive()Hauke Mehrtens2022-05-171-0/+79
| | | | | | | | | | | This backports a patch from Linux 5.10.116 to fix a compile problem introduced in 5.10.114. drivers/usb/phy/phy-generic.c could not find devm_regulator_get_exclusive(). Fixes: 8592df67f40b ("kernel: bump 5.10 to 5.10.114") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 5.15 to 5.15.40John Audia2022-05-165-10/+5
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.39John Audia2022-05-1632-1822/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Removed upstreamed: backport-5.15/850-v5.17-0001-PCI-pci-bridge-emul-Add-description-for-class_revisi.patch backport-5.15/850-v5.17-0002-PCI-pci-bridge-emul-Add-definitions-for-missing-capa.patch backport-5.15/850-v5.17-0003-PCI-aardvark-Add-support-for-DEVCAP2-DEVCTL2-LNKCAP2.patch backport-5.15/850-v5.17-0004-PCI-aardvark-Clear-all-MSIs-at-setup.patch backport-5.15/850-v5.17-0005-PCI-aardvark-Comment-actions-in-driver-remove-method.patch backport-5.15/850-v5.17-0006-PCI-aardvark-Disable-bus-mastering-when-unbinding-dr.patch backport-5.15/850-v5.17-0007-PCI-aardvark-Mask-all-interrupts-when-unbinding-driv.patch backport-5.15/850-v5.17-0008-PCI-aardvark-Fix-memory-leak-in-driver-unbind.patch backport-5.15/850-v5.17-0009-PCI-aardvark-Assert-PERST-when-unbinding-driver.patch backport-5.15/850-v5.17-0010-PCI-aardvark-Disable-link-training-when-unbinding-dr.patch backport-5.15/850-v5.17-0011-PCI-aardvark-Disable-common-PHY-when-unbinding-drive.patch pending-5.15/850-0001-PCI-aardvark-Replace-custom-PCIE_CORE_INT_-macros-wi.patch pending-5.15/850-0004-PCI-aardvark-Rewrite-IRQ-code-to-chained-IRQ-handler.patch pending-5.15/850-0005-PCI-aardvark-Check-return-value-of-generic_handle_do.patch pending-5.15/850-0006-PCI-aardvark-Make-MSI-irq_chip-structures-static-dri.patch pending-5.15/850-0007-PCI-aardvark-Make-msi_domain_info-structure-a-static.patch pending-5.15/850-0008-PCI-aardvark-Use-dev_fwnode-instead-of-of_node_to_fw.patch pending-5.15/850-0009-PCI-aardvark-Refactor-unmasking-summary-MSI-interrup.patch pending-5.15/850-0010-PCI-aardvark-Add-support-for-masking-MSI-interrupts.patch pending-5.15/850-0011-PCI-aardvark-Fix-setting-MSI-address.patc pending-5.15/850-0012-PCI-aardvark-Enable-MSI-X-support.patch pending-5.15/850-0013-PCI-aardvark-Add-support-for-ERR-interrupt-on-emulat.patch pending-5.15/850-0015-PCI-aardvark-Optimize-writing-PCI_EXP_RTCTL_PMEIE-an.patch pending-5.15/850-0016-PCI-aardvark-Add-support-for-PME-interrupts.patch pending-5.15/850-0017-PCI-aardvark-Fix-support-for-PME-requester-on-emulat.patch pending-5.15/850-0018-PCI-aardvark-Use-separate-INTA-interrupt-for-emulate.patch pending-5.15/850-0019-PCI-aardvark-Remove-irq_mask_ack-callback-for-INTx-i.patch pending-5.15/850-0020-PCI-aardvark-Don-t-mask-irq-when-mapping.patch pending-5.15/850-0021-PCI-aardvark-Drop-__maybe_unused-from-advk_pcie_disa.patch pending-5.15/850-0022-PCI-aardvark-Update-comment-about-link-going-down-af.patch All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.115John Audia2022-05-1627-159/+43
| | | | | | | | | | | | | Removed upstreamed: backport-5.10/850-v5.17-0004-PCI-aardvark-Clear-all-MSIs-at-setup.patch pending-5.10/850-0002-PCI-aardvark-Fix-reading-MSI-interrupt-number.patch All other patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.114John Audia2022-05-1616-30/+30
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B Run-tested: bcm2711/RPi4B Signed-off-by: John Audia <therealgraysky@proton.me>
* ramips: Add support for SERCOMM NA502SAndreas Böhler2022-05-164-0/+379
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The SERCOMM NA502s is a smart home gateway manufactured by SERCOMM and sold under different brands (among others, A1 Telekom Austria SmartHome Premium Gateway). It has multi-protocol radio support in addition to LAN and WiFi. Note: BLE and audio are currently unsupported. Specifications -------------- - MT7621ST 880MHz, Single-Core, Dual-Thread - MT7603EN 2.4GHz WiFi - MT7662EN 5GHz WiFi + BLE - 128MiB NAND - 256MiB DDR3 RAM - SD3503 ZWave Controller - EM357 Zigbee Coordinator - Telit UMTS module - Rechargeable battery - speaker and microphone MAC address assignment ---------------------- LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the OEM firmware does not enable 5GHz WiFi. Installation ------------ Attach serial console, then boot the initramfs image via TFTP. Once inside OpenWrt, run sysupgrade -n with the sysupgrade file. Attention: The device has a dual-firmware design. We overwrite kernel2, since kernel1 contains an automatic recovery image. If you get NAND ECC errors and are stuck with bad eraseblocks, try to erase the mtd partition first with mtd unlock ubi mtd erase ubi This should only be needed once. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ramips: add led_source for Asus RT-AC1200 devicesTamas Balogh2022-05-151-0/+1
| | | | | | | | | | | | | | | this adds the mediatek,led_source dts binding for Asus RT-AC1200 devices' dtsi, for correct switch LED behavior. The dts-binding is introduced in commit: 65dc9e0980255b15402c45b840f239b85be59b3d Without this, we only have constantly very fast blinking LEDs, which don't react on any traffic or LAN events at all. Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
* IPQ4019: AVM FRITZ!Box 7530: Remove NAND ECC restrictions from DTSAndreas Böhler2022-05-151-0/+3
| | | | | | | | | Some revisions of the FRITZ!7530 use a Toshiba NAND with 8 bit ECC in contrast to the Macronix NAND with 4 bit ECC. This removes the hardcoded ECC strength and step size as set in qcom-ipq4019.dtsi, thus relying on the kernel NAND detection routines to correclty set up the ECC parameters. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* kernel: add support for Toshiba TC58NVG0S3HTA00 NAND flashAndreas Böhler2022-05-152-0/+72
| | | | | | | The Toshiba TC58NVG0S3HTA00 is detected with 64 byte OOB while the flash has 128 byte OOB. This adds a static NAND ID entry to correct this. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ath79: ZTE MF286[A,R]: add "Power button blocker" GPIO switchLech Perczak2022-05-151-0/+20
| | | | | | | | | | | | | | | ZTE MF286A and MF286R feature a "power switch override" GPIO in stock firmware as means to prevent power interruption during firmware update, especially when used with internal battery. To ensure that this GPIO is properly driven as in stock firmware, configure it with userspace GPIO switch. It was observed that on some units, the modem would not be restarted together with the board itself on reboot, this should help with that as well. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ipq40xx: revert Cell-C RTL30VW to legacy caldata extractionPawel Dembicki2022-05-152-15/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This partially reverts commit cfc13c44595d ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data"). After switching to nvmem RTL30VW, wifi was broken: [ 19.118319] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 [ 19.118377] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 19.130285] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b [ 19.159092] ath10k_ahb a000000.wifi: failed to fetch board data for bus=ahb,vendor=0000,device=0000,subsystem-vendor=0000,subsystem-device=0000,variant=cellc,rtl30vw from ath10k/QCA4019/hw1.0/board-2.bin [ 19.238764] ath10k_ahb a000000.wifi: failed to fetch board-2.bin or board.bin from ath10k/QCA4019/hw1.0 [ 19.238847] ath10k_ahb a000000.wifi: failed to fetch board file: -12 [ 19.247362] ath10k_ahb a000000.wifi: could not probe fw (-12) [ 20.190797] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 [ 20.190853] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 20.202893] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b [ 20.231357] ath10k_ahb a800000.wifi: failed to fetch board data for bus=ahb,vendor=0000,device=0000,subsystem-vendor=0000,subsystem-device=0000,variant=cellc,rtl30vw from ath10k/QCA4019/hw1.0/board-2.bin [ 20.317318] ath10k_ahb a800000.wifi: failed to fetch board-2.bin or board.bin from ath10k/QCA4019/hw1.0 [ 20.317399] ath10k_ahb a800000.wifi: failed to fetch board file: -12 [ 20.326098] ath10k_ahb a800000.wifi: could not probe fw (-12) Bootloader mangles in NAND partitions and removes precal@X nodes in working system: root@OpenWrt:~# echo $(cat /sys/firmware/devicetree/base/soc/spi@78b5000/flash@0/partitions/partition@170000/label) 0:ART root@OpenWrt:~# ls /sys/firmware/devicetree/base/soc/spi@78b5000/flash@0/partitions/partition@170000/ label name reg Revert to legacy method fixed the problem. Fixes: cfc13c44595d ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data") Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ath79: fix I2C on GL-AR300M devicesPtilopsis Leucotis2022-05-151-0/+9
| | | | | | | | | | | On GL-AR300M Series GPIO17 described as I2C SDA in Device Tree. Because of GPIO_OUT_FUNCTION4 register was not initialized on start, GPIO17 was uncontrollable, it always in high state. According to QCA9531 documentation, default setting of GPIO17 is SYS_RST_L. In order to make GPIO17 controllable, it should write value 0x00 on bits [15:8] of GPIO_OUT_FUNCTION4 register, located at 0x1804003C address. Signed-off-by: Ptilopsis Leucotis <PtilopsisLeucotis@yandex.com>
* mpc85xx: enable error reporting for RAM and PCIeJosef Schlehofer2022-05-141-0/+4
| | | | | | | | | | | | | | | | | | | | All Freescale processors used in this target are capable to detect error and correction. [1] It can not be used as kernel module. [2] This is helpful to report hardware errors. It enables three kernel options: - EDAC, which is a subsystem - EDAC_LEGACY_SYSFS, it enables sysfq nodes - MP85XX, support for Freescale MPC8349, MPC8560, MPC8540, MPC8548, T4240 EDAC is already enabled for following targets: qoriq, octeon, octeontx and zynq. [1] https://cateee.net/lkddb/web-lkddb/EDAC.html [2] https://patchwork.ozlabs.org/patch/554908/ Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* ipq-wifi: drop upstreamed board-2.binChristian Lamparter2022-05-143-20/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The BDFs for the: Aruba AP-303 ASUS RT-AC42U AVM FRITZ!Repeater 1200 Buffalo WTR-M2133HP Cell C RTL30VW D-Link DAP-2610 EnGenius EAP2200 EnGenius EMD1 EnGenius EMR3500 EnGenius EMR5000 EZVIZ CS-W3-WD1200G EUP Google Wifi Linksys MR8300 V1.0 Luma WRTQ-329ACN MobiPromo CM520-79F NEC Platforms WG2600HP3 Plasma Cloud PA1200 (updated version) Plasma Cloud PA2200 ZTE MF286D were upstreamed to the ath10k-firmware repository and landed in linux-firmware.git. Furthermore the BDFs for the: 8devices Habanero OpenMesh A62 OpenMesh A42 AVM FRITZ!Box 4040 have been updated. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: Lyra: update RGB LED-Controller node for 5.10+Christian Lamparter2022-05-142-47/+78
| | | | | | | | | | | | | | | | | | | | | | Add the reg and color property to each channel node. This update is to accommodate the multicolor framework. Refer to: <https://lore.kernel.org/all/20200622185919.2131-9-dmurphy@ti.com> <https://lore.kernel.org/all/20210818070209.1540451-1-michal.vokac@ysoft.com> Note: There is only a single extremely bright RGB-LED. The RGB-color channels (i.e.: blue-0, blue-1 and blue-2) are running in parallel to increase the current delivery beyond what a single PWM-output on the LED controller could do. BugLink: https://github.com/openwrt/openwrt/issues/9851 Reported-By: Thomas Bøge <thomas@boegenielsen.dk> Tested-By: Thomas Bøge <thomas@boegenielsen.dk> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: use nested fixed-partitionsChristian Lamparter2022-05-142-24/+47
| | | | | | | | This makes it possible to fix Netgear WNDAP620+660 DTS ugliness. Bring back the dtb and firmware partitions for the WNDR4700. Thank you, mans0n. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* bcm53xx: remove MR32's specific get_leds_dt codeChristian Lamparter2022-05-142-31/+0
| | | | | | | the existing diag.sh code will pick up the LED by itself. This is not/no longer needed. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* lantiq: xway: disable unused switch driversAleksander Jan Bajkowski2022-05-141-3/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | None of the devices supported by target xway are using Realtek RTL8366S, RTL8367A and RTL8367B switches. The switches mentioned earlier were enabled when bumping the kernel version to 3.7 in commit 3a948770cf46 ("add linux-v3.7"). Switches used by individual devices are listed below. Device Switch PHY Arcadyan ARV4510PW Infineon ADM6996I int. switch Arcadyan ARV4519PW Atheros AR8216 int. switch Arcadyan ARV7506PW11 Realtek RTL8306G int. switch Arcadyan ARV7510PW22 Atheros AR8216 int. switch Arcadyan ARV7518PW Atheros AR8216 int. switch Arcadyan ARV7519PW Atheros RTL8306G int. switch Arcadyan ARV7525PW N/A IC+ IP101A Arcadyan ARV752DPW Realtek RTL8306G int. switch Arcadyan ARV752DPW22 Atheros AR8216 int. switch Arcadyan ARV8539PW22 Atheros AR8216 int. switch AVM Fritzbox 7312 int. SoC Atheros AR8030-A AVM Fritzbox 7320 int. SOC Lantiq PEF7071V AudioCodes MediaPack MP-252 Infineon ADM6996I int. switch BT Home Hub 2B Infineon ADM6996I int. switch BT Home Hub 3A Infineon PSB6972 Lantiq PEF7071V Buffalo WBMR-HP-G300H-A Atheros AR8316 int. switch Buffalo WBMR-HP-G300H-B Atheros AR8316 int. switch Lantiq EASY50712 Infinein ADM6996I int. switch Netgear DGN3500 Realtek RTL8366RB int. switch Netgear DGN3500B Realtek RTL8366RB int. switch Siemens Gigaset sx76x Infineon ADM6996I int. switch ZTE H201L Realtek RTL8306G int. switch ZyXEL P-2601HN-F1 Realtek RTL8306E int. switch ZyXEL P-2601HN-F3 Realtek RTL8306E int. switch Reduces uncompressed kernel size by 36 kB. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> (checkpatch.pl fixes) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: fix booting on Samknows SK-WB8Piotr Dymacz2022-05-131-0/+1
| | | | | | | | This fixes a well known "LZMA ERROR 1" error, reported previously on numerous of similar devices. Fixes: #9824 Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* realtek: do not reset SerDes on link changeBirger Koblitz2022-05-112-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Do not reset the RTL930x SerDes on link changes, instead set up the SDS with internal PHYs for the SFP+ ports only. This fixes the 8 1GBit ports on the Zyxel XGS1250 which do not work without this patch. A complete SerDes reset was performed on all SerDes links. For copper 1Gbit ports, this is commonly a single XGMII link to an RTL8218D. There is however no support for setting up the XGMII link on RTL9300/RTL9310, thereby wiping the (RX/TX) setup done by u-boot and breaking the 1GBit ports. No SerDes reset should be done for these links. The handling of SGMII/HiSGMII, 1000BX or 10GR links is actually entirely different. All these modes need to be suitably RX calibrated and the pre- main and post- amplifiers set up properly for TX. The 10GBit SFP+ fiber links are recalibrated instead of reset, which e.g. is necessary when someone pulls a module out and puts another in. This makes swapping out 10GBit fiber modules possible. 1GBit modules are not yet supported, nor any modules with an internal phy. Tested-by: Stijn Segers <foss@volatilesystems.org> Signed-off-by: Birger Koblitz <git@birger-koblitz.de> [rewrite commit message based on discussion] Link: http://lists.infradead.org/pipermail/openwrt-devel/2022-May/038623.html Signed-off-by: Sander Vanheule <sander@svanheule.net>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-01 20:20:01 +0000