aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: fix system LED names on Archer C5/C7Tomislav Požega2019-07-281-2/+2
| | | | | | | | Move system LED board definitions of Archer C5/C7 to reflect actual system LED colour used Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com> (cherry picked from commit a73934fc9ad05207e79a3e58abc3d14eee28b6f2)
* ar71xx: Archer C7 v1 LED names and RFKILL fixesTomislav Požega2019-07-281-10/+10
| | | | | | | | | | | All leds on these boards are green. v1 has RFKILL GPIO 23 for production units (it had GPIO 13 only for test phase units, and these are rather very rare to find). As for the previous attempt to fix this and revert due to WDR boards have blue leds, it was wrong: WDR board does not use common setup (false). Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com> (cherry picked from commit c79c001b593bd826d51722f2c83ad8770255f3b3)
* ar71xx: update qca-usb-quirks patchTomislav Požega2019-07-281-1/+1
| | | | | | | | Base address for USB0 has changed from 0x18116c94 on AR934X to 0x18116d94 on QCA9558. CP Typo remained for years here... Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com> (cherry picked from commit fd5aa19480b92045db224a2d2450680e9fe66385)
* ramips: add support for ASUS RT-AC57UDavid Bauer2019-07-213-4/+167
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621AT RAM: 128M (Winbond W631GG6KB-15) FLASH: 16MB (Spansion S25FL128SA) WiFi: MediaTek MT7603EN bgn 2SS WiFi: MediaTek MT7612EN nac 2SS BTN: Reset - WPS LED: - Power - LAN {1-4} - WAN - WiFi 2.4 GHz - WiFi 5 GHz - USB UART: UART is present next to the Power LED. TX - RX - GND - 3V3 / 57600-8N1 3V3 is the nearest one to the Power LED. Installation ------------ Via TFTP: 1. Set your computers IP-Address to 192.168.1.75. 2. Power up the Router with the Reset button pressed. 3. Release the Reset button after 5 seconds. 4. Upload OpenWRT sysupgrade image via TFTP: > tftp -4 -v -m binary 192.168.1.1 -c put <IMAGE> Via SSH: Note: User/password for SSH is identical with the one used in the Web-interface. 1. Complete the initial setup wizard. 2. Activate SSH under "Administration" -> "System". 3. Transfer the OpenWrt sysupgrade image via scp: > scp owrt.bin admin@192.168.1.1:/tmp 4. Connect via SSH to the router. > ssh admin@192.168.1.1 5. Write the OpenWrt image to flash. > mtd-write -i /tmp/owrt.bin -d linux 6. Reboot the router > reboot Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 14e0e4f138e35c3e2a15cc3a836c939547ee053b)
* ath79: add support for devolo WiFi pro 1750xDavid Bauer2019-07-214-1/+64
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm Atheros QCA9558 RAM: 128M DDR2 FLASH: 16MiB ETH: 1x Atheros AR8035 (PoE in) WiFi2: QCA9558 3T3R WiFi5: QCA9880 3T3R BTN: 1x Reset LED: 1x LED Power (non-controllable) 1x LED Status (internal) 1x LED LAN (controlled by PHY) 1x LED WLAN BEEP: 1x GPIO attached piezo beeper UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad) Header is located next to external-LED header. Installation ------------ Make sure you set a password for the root user as prompted on first setup! 1. Upload OpenWRT sysupgrade image via SSH to the device. Use /tmp as the destination folder on the device. User is root, password the one set in the web interface. 2. Install OpenWRT with > sysupgrade -n -F /tmp/<openwrt-image-name> Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit cb3cd526948af3f69da1af18e035177a0a8f58e3)
* ar71xx: enable SGMII fixup on Mikrotik wAP ACEtienne Champetier2019-07-211-0/+16
| | | | | | | | | | | | | | | | | fixes intermittent loss of connectivity on 1Gbit port, with log message: > 803x_aneg_done: SGMII link is not ok Thanks to David Bauer for pointing me in the right direction. I just had to figure out the right bus_id, which you find in this log: > ag71xx ag71xx.1: connected to PHY at gpio-1:00 [uid=004dd074, driver=Atheros 8031 ethernet] Fixes FS#2236 Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com> [Wrapped commit message - Fixed whitespace erors] Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 2a7519e29d6cbbe1eb73623ef35add0ef596fb5f)
* mt7620: disable image generation for Netgear EX2700Petr Štetiar2019-07-201-1/+1
| | | | | | | | | Image generation is currently failing on builbots due to the following error: WARNING: Image file [...] mt7620-ex2700-squashfs-factory.bin is too big Signed-off-by: Petr Štetiar <ynezz@true.cz>
* x86: add modern network modules to Generic targetAlberto Bursi2019-07-201-1/+2
| | | | | | | | | | | | | | | | Many Atom-based embedded/industrial x86 boards can't run 64bit operating systems due to either processor or board firmware limitations, but they have modern interfaces (PCIe) or have modern Intel gigabit controllers onboard. With the current default package selection for x86 Generic target their network won't work. Add the modern gigabit network modules needed or most likely going to be used as add-in cards, similar to what is the list on x86_64 target. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it> [fixed whitespace issue] Signed-off-by: Petr Štetiar <ynezz@true.cz> (cherry picked from commit bb27cde2579b0273c464e5ccd3dda7d14e84fd23)
* ath25: disable image generation for ubnt2 and ubnt5 devicesPetr Štetiar2019-07-201-2/+2
| | | | | | | | | | | | | | | | Image generations is currently failing on builbots due to the following errors: mkfwimage -B XS2 -v XS2 [...] ath25-ubnt2-squashfs-sysupgrade.bin ERROR: Failed creating firmware layout description - error code: -2 mkfwimage -B XS5 -v XS5 [...] ath25-ubnt5-squashfs-sysupgrade.bin ERROR: Failed creating firmware layout description - error code: -2 That cryptic -2 error simply means, that kernel+rootfs doesn't fit into the firmware partition. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: Use -v1 suffix for TP-Link WDR3600/4300Adrian Schmutzler2019-07-175-14/+14
| | | | | | | | | | | | | | | In ath79, identifiers tplink_tl-wdr3600 and tplink_tl-wdr4300 have been used while most other TP-Link devices include the revision. Although there actually is only one major revision of these devices, they bear the revision on their bottom (v1.x). TP-Link also refers to the devices as V1 on its web page. This patch thus adds -v1 to both so it is more consistent with other devices and with what you would expect from reading the on-device sticker and the support pages. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: ar9330: add missing watchdog nodePetr Štetiar2019-07-171-0/+10
| | | | | | | | | It was reported in FS#2385, that Carambola2 doesn't currently have working watchdog so fix it by adding watchdog node. Ref: FS#2385 Signed-off-by: Petr Štetiar <ynezz@true.cz> (cherry picked from commit 0893f28e19afbd9d4081f59df10631d6ef02e0d7)
* ar71xx: fix nand init issues on some rb2011 devicesKoen Vandeputte2019-07-121-1/+5
| | | | | | | | | | | | | | | | | | | | While flashing lots of RB2011 devices, I noticed that some of them refused to boot properly, failing over the NAND parameters. Checking in detail shows that some device seem to use another NAND flash which only support standard 2048-byte pages, without 512-byte subpage support. This commit disables usage of these small subpage completely. Advantages: - Both NAND's with(out) subpage support are working now - The nand speed increases a bit (measured roughly 1%) in typical usecases Disadvantages: - The maximum storage capacity decreases by ~0.2% as small changes can consume a full page (2048 bytes) now. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.133Koen Vandeputte2019-07-121-5/+5
| | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-3900 Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: cherry pick patch removing __linux__ checkFredrik Olofsson2019-07-101-0/+47
| | | | | | | | | | | This is already included in newer upstream. Needed to build BPF programs using the MIPS kernel include files. Without this patch, clang fails with "#error Use a Linux compiler or give up." in sgidefs.h when building BPF programs. Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com> (cherry-picked from commit 7d96c301d6afc9f360c26b404e435e8e03c1e207)
* kernel: bump 4.14 to 4.14.132Koen Vandeputte2019-07-094-7/+7
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* mpc85xx: Use gzip compressed kernel on HiveAP-330Pawel Dembicki2019-07-051-1/+1
| | | | | | | | | | | | | | | | | | | After commit 1e41de2f48 ("mpc85xx: convert TL-WDR4900 v1 to simpleImage") XZ compression of zImage was enabled. This change exposed a problem with the HiveAP-330 images, which was fixed by foregoing the compression on the kernel altogether with commit 98089bb8ba8 ("mpc85xx: Use uncompressed kernel on the HiveAP-330"). This patch adds back the gzip compression of the kernel image by utilizing the generic OpenWRT uImage method instead of relying on the PowerPC bootwrapper script that did it previously. Compile-tested: p1020/hiveap-330 Tested-by: Chris Blake <chrisrblake93@gmail.com> [run-tested] Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [filled in even more text]
* lantiq: enable STP where referencedMathias Kresin2019-07-032-0/+2
| | | | | | | | | | | While moving common used parts to dtsi files, the was disabled by default but not enabled for all boards using the STP. Fixes: f519fea4c6db ("lantiq: kernel 4.14: cleanup dts files") Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* ar71xx: fix ath79/rb4xx IRQ initialization on kernel 4.14W. Michael Petullo2019-07-031-1/+1
| | | | | | | | | | | | | Apply the same approach as in commit 3b53d6fdbc24 ("ar71xx: fix pci irq init on kernel 4.14") to fix IRQ initialization for ath79-based chipsets on rb4xx. Ref: PR#2182 Acked-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: W. Michael Petullo <mike@flyn.org> [commit ref fix] Signed-off-by: Petr Štetiar <ynezz@true.cz> (cherry picked from commit 8c7d6c47a7893db689e50e1917479ad07a96547a)
* mvebu: Fix platform.sh for non-generic espressobin versionsBrett Mastbergen2019-06-281-2/+4
| | | | | | | | | When the non-generic espressobin targets were added these board checks were not updated. One side effect of this is that config is not saved during an upgrade of -emmc,-v7, or -v7-emmc devices. Signed-off-by: Brett Mastbergen <bmastbergen@untangle.com> (cherry picked from commit 95c1dc5e8678a1fd87234a4d77c8c6643703023c)
* mvebu: fix regression for non-generic ESPRESSObin versionsVladimir Vid2019-06-282-2/+6
| | | | | | | | | | | | | | When targets for multiple ESPRESSObin devices were added, not all files were updated which means any ESPRESSObin version beside generic won't have proper networking, sysupgrade and uboot-env. This patch fixes the issue. * fixup network detection * fixup uboot-env * fixup platform.sh for sysupgrade Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr> (cherry picked from commit bc47285cb3c0125424e628521f905f1f0d7b4cef)
* mvebu: image: fix generic-arm64.bootscript mmc selectionVladimir Vid2019-06-281-2/+8
| | | | | | | | | | | Not all versions of ESPRESSObin require SD card, but can be booted from the internal emmc flash (mmc dev 1) instead. Add a simple check in the bootscript to see which mmc device is detected and boot from it using mmcdev variable. Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl> Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr> (cherry picked from commit 008b41b9b0ddd4c5c877a769a85d27eb9c4e21a4)
* ramips: mt7621: add IRQ for GPIO nodeChuanhong Guo2019-06-271-0/+3
| | | | | | | This makes interrupt-based gpio-keys working. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> (cherry picked from commit 110daa16e44bb53941a18396ab6a7d9fdd1fa362)
* layerscape: drop pause frame support for aquantia phyYangbo Lu2019-06-261-52/+10
| | | | | | | | | | | | An aquantia phy patch which dropped pause frame support was missing when integrated LSDK-19.03 kernel patches into OpenWrt. Without this patch, LS1043A 10G port would not work. So apply it. Patch link https://source.codeaurora.org/external/qoriq/qoriq-components/ linux/commit/?h=linux-4.14&id=66346b115818365cfaf99d292871b19f0a1d2850 Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* kernel: bump 4.14 to 4.14.130Koen Vandeputte2019-06-257-10/+10
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* apm821xx: fix bogus key-presses on bootChristian Lamparter2019-06-245-0/+37
| | | | | | | | | | | | | | | | | | | | | | | "There are often transient line events when the system is powered up and initialized and it is often necessary for the gpio_chip driver to clear any interrupt flags in hardware before setting up the gpio chip, especially the irqchip portions of it." <http://lists.infradead.org/pipermail/openwrt-devel/2019-June/017630.html> This patch adds a fix for the APM821XX's interrupt controller to clear any bogus pending toggled interrupts that happens on various APM821XX boards on boot. The patch also changes the debouce-interval from the default 5ms debounce interval to 60ms all around. The default setting caused on occasions that the button state became stuck in a pressed state, even though the button was released. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: Use uncompressed kernel on the HiveAP-330Chris Blake2019-06-241-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It seems that newer builds of OpenWRT have a gzip kernel larger than 2MB~, which for some reason fails to boot on this board. However, we have 8MB of kernel space and currently the uncompressed kernel is 6.5MB~, so we have some space to grow until a better solution is worked out. Before: ## Booting kernel from Legacy Image at ee840000 ... Image Name: Linux-4.19.53 Created: 2019-06-22 11:17:48 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 2315724 Bytes = 2.2 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02000000 ... Image Name: OpenWrt fake ramdisk Created: 2019-06-22 11:17:48 UTC Image Type: PowerPC Linux RAMDisk Image (uncompressed) Data Size: 0 Bytes = 0 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at ec000000 Booting using the fdt blob at 0xec000000 Uncompressing Kernel Image ... Error: Bad gzipped data GUNZIP: uncompress, out-of-mem or overwrite error - must RESET board to recover Loading Ramdisk to 10000000, end 10000000 ... OK Loading Device Tree to 00ffa000, end 00fffc78 ... OK ft_fixup_l2cache: FDT_ERR_NOTFOUND After: ## Booting kernel from Legacy Image at ee840000 ... Image Name: POWERPC OpenWrt Linux-4.19.53 Created: 2019-06-22 11:17:48 UTC Image Type: PowerPC Linux Kernel Image (uncompressed) Data Size: 6724584 Bytes = 6.4 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02000000 ... Image Name: OpenWrt fake ramdisk Created: 2019-06-22 11:17:48 UTC Image Type: PowerPC Linux RAMDisk Image (uncompressed) Data Size: 0 Bytes = 0 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at ec000000 Booting using the fdt blob at 0xec000000 Loading Kernel Image ... OK OK Loading Ramdisk to 10000000, end 10000000 ... OK Loading Device Tree to 00ffa000, end 00fffc78 ... OK Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [75 cpl limit]
* ipq40xx: Linksys: sysupgrade: Ensure OEM volumes are removedJeff Kletsky2019-06-241-20/+22
| | | | | | | | | | | | | | | | | | When OEM volumes are present in the [alt_]firmware partition, sysupgrade will write a new kernel, but will fail to write the root file system. The next boot will hang indefinitely Waiting for root device /dev/ubiblock0_0... Modified ipq40xx/base-files/lib/upgrade/linksys.sh to remove both `squashfs` and `ubifs` if found on the target firmware partition's UBI device. Run-tested-on: Linksys EA8300 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [applied some shellcheck suggestions as well]
* kernel: bump 4.14 to 4.14.129Koen Vandeputte2019-06-247-26/+8
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: update act_ctinfoKevin Darbyshire-Bryant2019-06-201-10/+28
| | | | | | | | Follow upstream changes - header file changes no executable difference at all Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> (cherry picked from commit 5273fb6b21b953428e2f9ea5892872db5aaf22c1)
* ath79: Add SUPPORTED_DEVICES for Archer C7 v1/v2Adrian Schmutzler2019-06-201-0/+2
| | | | | | | | The identifier for both devices is "archer-c7" on ar71xx, set here: https://github.com/openwrt/openwrt/blob/master/target/linux/ar71xx/base-files/lib/ar71xx.sh#L348 https://github.com/openwrt/openwrt/blob/master/target/linux/ar71xx/base-files/lib/ar71xx.sh#L511 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 4.14 to 4.14.128Koen Vandeputte2019-06-2010-22/+22
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: base-files: fix board detect on new MikroTik devicesHenryk Heisig2019-06-191-147/+165
| | | | | | | | | | | | | | | | | | | | Move all MikroTik devices to new function to increase script execution speed. Machine name in new version of MikroTik RouterBOARD devices add "RB" before model name: Old machine name: MikroTik RouterBOARD 951Ui-2nD New: MikroTik RouterBOARD RB951Ui-2nD So this patch should fix it for all currently supported MikroTik boards. Tested-by: Cezary Jackiewicz <cezary@eko.one.pl> [wAP R-2nD] Signed-off-by: Henryk Heisig <hyniu@o2.pl> [rebased,commit message facelift,script fixes] Signed-off-by: Petr Štetiar <ynezz@true.cz> [spotted missing 922UAGS-5HPacD] Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.127Koen Vandeputte2019-06-188-11/+11
| | | | | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-11479 - CVE-2019-11478 - CVE-2019-11477 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.126Koen Vandeputte2019-06-184-9/+120
| | | | | | | | | | | | | | | | | | Refreshed all patches. Altered patches: - 816-pcie-support-layerscape.patch This patch also restores the initial implementation of the ath79 perfcount IRQ issue. (78ee6b1a40b5) It was wrongfully backported upstream initially and got reverted now. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* mvebu: fixes commit 4089df4f4b0dGeorge Amanakis2019-06-171-1/+1
| | | | | | | | | | | | | err_free_stats has been deprecated. Replace with err_netdev. Compile-tested on: mvebu Runtime-tested on: mvebu Fixes: 4089df4f4b0d ("kernel: bump 4.14 to 4.14.125 (FS#2305 FS#2297)") Signed-off-by: George Amanakis <gamanakis@gmail.com> [altered hashes] Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> (cherry picked from commit 1e3800df1808b4a5a977c3a9651958611df51c83)
* kernel: backport 4.18 patch adding DMI_PRODUCT_SKURafał Miłecki2019-06-171-0/+57
| | | | | | | | | | It's needed for applying some hardware quirks. This fixes: drivers/net/wireless/broadcom/brcm80211/brcmfmac/dmi.c:60:20: error: 'DMI_PRODUCT_SKU' undeclared here (not in a function); did you mean 'DMI_PRODUCT_UUID'? DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "T8"), Fixes: c52054e568d1 ("mac80211: brcm: backport remaining brcmfmac 5.2 patches") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 4d11c4c3784196ed3e5b5a1f81fa415d99ef32b0)
* kernel: mt29f_spinand: fix memory leak during page programMantas Pucka2019-06-151-0/+90
| | | | | | | | | Memory is allocated with devm_kzalloc() on every page program and leaks until device is closed (which never happens). Convert to kzalloc() and handle error paths manually. Signed-off-by: Mantas Pucka <mantas@8devices.com>
* kernel: bump 4.14 to 4.14.125 (FS#2305 FS#2297)Koen Vandeputte2019-06-1226-1101/+350
| | | | | | | | | | | | | | | | Refreshed all patches. This bump contains upstream commits which seem to avoid (not properly fix) the errors as seen in FS#2305 and FS#2297 Altered patches: - 403-net-mvneta-convert-to-phylink.patch - 410-sfp-hack-allow-marvell-10G-phy-support-to-use-SFP.patch Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: drop everything not on kernel version 4.14Daniel Golle2019-06-12738-113992/+0
| | | | | | | | | | * Remove testing patches for kernel version 4.19 * remove targets ar7, ixp4xx, orion Those targets are still on kernel 4.9, patches for 4.14 were not ready in time. They may be readded once people prepare and test patches for kernel 4.14. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: Remove redundant LED-casesKristian Evensen2019-06-101-68/+32
| | | | | | | 01_leds has several redundant LED-cases. This commit cleans up the file by merging these cases into shared cases. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ath79: Add support for TP-Link Archer C25 v1Adrian Schmutzler2019-06-106-9/+231
| | | | | | | | | | | | | | | | | The TP-Link Archer C25 is a low-cost dual-band router. Specification: - CPU: Atheros QCA9561 775 MHz - RAM: 64 MB - Flash: 8 MB - Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887 - NET: 5x 10/100 Mbps Ethernet Some LEDs are controlled by an additional 74HC595 chip, but not all of them as e.g. for the C59. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Reorder some TP-Link Archer devices in 01_ledsAdrian Schmutzler2019-06-101-8/+8
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7620: select kmod-rt2800-pci driver for RT5592Deng Qingfang2019-06-101-1/+3
| | | | | | | | | | | ASUS RP-N53 and Buffalo WHR-600D use RT5592 for 5GHz wireless After commit 367813b9b17 the driver for RT5592 (rt2800pci) is not selected by default anymore, which broke their 5GHz wireless Add it back to device packages Fixes: 367813b9b17 ("ramips: mt7620: fix dependencies") Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ath79: migrate Archer C7 5GHz radio device pathsDavid Santamaría Rogado2019-06-101-6/+20
| | | | | | | | | | | | | | | | | | When upgrading a TP-Link Archer C7 v2 from ar71xx to ath79, the 5ghz radio stops working because the device path changed. Some people subtitute the unsupported QCA9880v1 in the Archer v1 with supported QCA9880v2 radio. Since the stock radio doesn't work, so it's safe to apply the change also for the Archer v1 images as well. Also this patch renames the migration file and variables from wmac to wifi. Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed comment, added return 0 (not that it matters since uci is clever, see 00-wmac-migration thread), reworded commit message]
* ath79: Consistently label art partition with lower caseAdrian Schmutzler2019-06-1019-36/+33
| | | | | | | | This patch harmonizes the label and alias for art partitions across ath79. Since lower case seems to be more frequent, use that consistently. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Read MAC addresses from flash in 11-ath10k-caldataAdrian Schmutzler2019-06-101-14/+23
| | | | | | | | | | In commit c3a8518 eth0 and eth1 have been swapped for some devices, but 11-ath10k-caldata has not been updated. Instead of fixing this by swapping eth0/eth1, this patch will read addresses from flash (as done for several devices already) so adjustments due to eth order become obsolete. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Consistently label info partitionAdrian Schmutzler2019-06-107-15/+9
| | | | | | | | | | | | | | | | The info/product-info partition, which frequently contains MAC adresses, is typically assigned the 'info' alias in DTS, but then labelled with 'info', 'product-info' or 'config'. This leads to different aliases if used for setting MAC adresses in DTS compared to when using e.g. mtd_get_mac_binary. Occationally, also multiple switch-case entries are used just because of different labelling. This patch relabels those partitions in ath79 to consistently use 'info'. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mpc85xx: re-enable TL-WDR4900v1 imagesPawel Dembicki2019-06-101-1/+1
| | | | | | | | | This reverts commit 324e94f31bfd ("mpc85xx: disable bricking TL-WDR4900v1 images") The previous commit fixes the TL-WDR4900v1. Enable the target again. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: convert TL-WDR4900 v1 to simpleImageChristian Lamparter2019-06-108-212/+165
| | | | | | | | | | | | | | | | | Converts the TP-Link WDR4900 v1 to use the simpleImage in the hopes of prolonging the life of the device. While at it, the patch makes the fdt.bin an ARTIFACT and sets the KERNEL_SIZE to 2684 KiB as a precaution since the stock u-boot is using a fixed kernel size. Note: Give the image some time, it will take much longer to extract and boot. [tested for 4.14/4.19] Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Co-authored-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kirkwood: image: fix unwanted 2nd inclusion of kernelPetr Štetiar2019-06-091-5/+5
| | | | | | | | | | | | | | | | | | | In commit d2e18dae2892 ("kirkwood: cleanup image build code") the image build code was refactored, setting KERNEL_IN_UBI=0 which doesn't work as the KERNEL_IN_UBI needs to be unset in order to make it working as intended, which leads to factory images with two kernels in them: binwalk --keep-going openwrt-kirkwood-cisco_on100-squashfs-factory.bin MD5 Checksum: c33e3d1eb0cb632bf0a4dc287592eb70 DECIMAL HEX DESCRIPTION ------------------------------------------------------------------------------- 0 0x0 uImage header [...] "ARM OpenWrt Linux-4.14.123" 5769216 0x580800 uImage header [...] "ARM OpenWrt Linux-4.14.123" Cc: Mathias Kresin <dev@kresin.me> Ref: https://bugs.openwrt.org/index.php?do=details&task_id=2285 Fixes: d2e18dae2892 ("kirkwood: cleanup image build code") Signed-off-by: Petr Štetiar <ynezz@true.cz>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 21:53:08 +0000