aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* kernel: bump 5.4 to 5.4.52John Audia2020-07-1724-133/+103
| | | | | | | | | update_kernel.sh refreshed all patches, no human interaction was needed Build system: x86_64 Run-tested: Netgear R7800 (ipq806x) Signed-off-by: John Audia <graysky@archlinux.us>
* ramips: add arl_table support for MT7530Salvatore Mesoraca2020-07-171-0/+119
| | | | | | | Use switch.h API to expose MT7530's ARL table to user space. Signed-off-by: Salvatore Mesoraca <salvatore@samknows.com>
* mvebu: add Kobol Helios 4 deviceAlberto Bursi2020-07-179-0/+100
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Helios 4 is a NAS from Kobol that is powered by an Armada 38x MicroSOM from Solidrun, similarly to Clearfog. This device has: -Armada 38x CPU (dual core ARMv7 1.6 Ghz) -2 GB of ECC RAM -Gigabit ethernet (Marvell) -2x USB 3.0 ports -4x Sata 3.0 ports -i2c header (J9 |>GND|SDA|SCL|VCC) -2x 3-pin fan headers with PWM -micro-usb port is a TTL/UART to USB converter connected to TTL -MicroSD card slot -System, 4xSata and 1xUSB LEDs NOT WORKING: fan control Fan Control requires a kernel patch that is available in the Armbian project (the "default firmware" of this device) and named mvebu-gpio-remove-hardcoded -timer-assignment This patch isn't acceptable by OpenWrt, it should be upstreamed. I also have that patch in my own local OpenWrt builds, in case you want a more clean and less confusing patch for upstreaming. To install, write the disk image on a micro SD card with dd or win32 disk imager, insert the card in the slot. Check that the dip switch battery for boot selection is as follows Switch 1 and 2 down/off, switches 3, 4, 5 up/on. Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
* ramips: add support for D-Link DIR-867/DIR-882 A1Mateus B. Cassiano2020-07-166-152/+275
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given the similarity of these devices, this patch also introduces a common DTS shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1. Specifications: * Board: AP-MTKH7-0002 * SoC: MediaTek MT7621AT * RAM: 128 MB (DDR3) * Flash: 16 MB (SPI NOR) * WiFi: MediaTek MT7615N (x2) * Switch: 1 WAN, 4 LAN (Gigabit) * Ports: 1 USB 2.0, 1 USB 3.0 * Buttons: Reset, WiFi Toggle, WPS * LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green), WiFi 5G (green), USB 2.0 (green), USB 3.0 (green) Notes: * WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips * DIR-867 wireless chips are limited to 3x3 streams at hardware level * USB ports and related LEDs available only on DIR-882 Serial port: * Parameters: 57600, 8N1 * Location: J1 header (close to the Reset, WiFi and WPS buttons) * Pinout: 1 - VCC 2 - RXD 3 - TXD 4 - GND Installation: * D-Link Recovery GUI: power down the router, press and hold the reset button, then re-plug it. Keep the reset button pressed until the power LED starts flashing orange, manually assign a static IP address under the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1 * Some modern browsers may have problems flashing via the Recovery GUI, if that occurs consider uploading the firmware through cURL: curl -v -i -F "firmware=@file.bin" 192.168.0.1 Signed-off-by: Mateus B. Cassiano <mbc07@live.com> [move DEVICE_VARIANT to individual definitions] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Linksys EA7300 v1Santiago Rodriguez-Papa2020-07-169-159/+238
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: * SoC: MediaTek MT7621A (880 MHz 2c/4t) * RAM: Nanya NT5CC128M16IP-DIT (256M DDR3-1600) * Flash: Macronix MX30LF1G18AC-TI (128M NAND) * Eth: MediaTek MT7621A (10/100/1000 Mbps x5) * Radio: MT7615N (2.4 GHz & 5 GHz) 4 antennae: 1 internal and 3 non-deatachable * USB: 3.0 (x1) * LEDs: White (x1 logo) Green (x6 eth + wps) Orange (x5, hardware-bound) * Buttons: Reset (x1) WPS (x1) Everything works! Been running it for a couple weeks now and haven't had any problems. Please let me know if you run into any. Installation: Flash factory image through GUI. This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. Signed-off-by: Santiago Rodriguez-Papa <contact@rodsan.dev> [use v1 only, minor DTS adjustments, use LINKSYS_HWNAME and add it to DEVICE_VARS, wrap DEVICE_PACKAGES, adjust commit message/title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: provide common definition for ELECOM WRC GS devicesAdrian Schmutzler2020-07-167-35/+24
| | | | | | | | | | | | | | Add a common definition for ELECOM WRC "GS" devices to mt7621.mk to not repeat the same assignments five times. To keep the naming consistent, slightly rename the DTSI and the factory image recipe as well. Note that elecom_wrc-1167ghbk2-s uses a slightly different build recipe for the factory image, so we keep it separate. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com> [WRC-1750GSV]
* ramips: add support for ELECOM WRC-1750GS/GSVINAGAKI Hiroshi2020-07-163-0/+106
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1750GS is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on MT7621A. WRC-1750GSV has the same hardware with WRC-1750GS. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : SPI-NOR 16 MiB - WLAN : 2.4/5 GHz 3T3R (2x MediaTek MT7615) - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (SoC) - LED/keys : 4x/6x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J4: 3.3V, GND, TX, RX from ethernet port side - 57600n8 - Power : 12VDC, 1.5A Flash instruction using factory image: 1. Boot WRC-1750GS (or WRC-1750GSV) normally 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button for WRC-1750GS : wrc-1750gs-squashfs-factory.bin for WRC-1750GSV: wrc-1750gsv-squashfs-factory.bin 4. Wait ~120 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* mediatek: backport latest pci/e driver from upstreamJohn Crispin2020-07-167-24/+1932
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* mediatek: generate UBI images for the rev boardJohn Crispin2020-07-163-2/+48
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* mediatek: minor fix to eip97 driverJohn Crispin2020-07-161-2/+2
| | | | | | This patch makes the driver work on the newer v2.3 core. Signed-off-by: John Crispin <john@phrozen.org>
* ath79: harmonize model names for Ubiquiti devicesAdrian Schmutzler2020-07-1517-27/+26
| | | | | | | | | | | | | | | | | | | | This harmonizes the model names for the ath79 Ubiquiti devices by applying a few minor cosmetic adjustments: - Removes hyphens where they are not found in the product names (Ubiquiti uses hyphens only for the abbreviated version names like UAP-AC-PRO which we don't use anyway.) - Add (XM) suffix for DTS model strings to help with distinguishing them from their XW counterparts. - Remove DEVICE_VARIANT for LAP-120 which actually was an alternate device name. - Generally make DTS model names and those from generic-ubnt.mk more consistent. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Ubiquiti PowerBridge MVieno Hakkerinen2020-07-155-0/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Ubiquiti PowerBridge M, which has the same board/LEDs as the Bullet M XM, but different case and antennas. Specifications: - AR7241 SoC @ 400 MHz - 64 MB RAM - 8 MB SPI flash - 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in - Internal antenna: 25 dBi - POWER/LAN green LEDs - 4x RSSI LEDs (red, orange, green, green) - UART (115200 8N1) on PCB Flashing via WebUI: Upload the factory image via the stock firmware web UI. Attention: airOS firmware versions >= 5.6 have a new bootloader with an incompatible partition table! Please downgrade to <= 5.5 _before_ flashing OpenWrt! Refer to the device's Wiki page for further information. Flashing via TFTP: Same procedure as other Bullet M (XM) boards. - Use a pointy tool (e.g., pen cap, paper clip) and keep the reset button on the device or on the PoE supply pressed - Power on the device via PoE (keep reset button pressed) - Keep pressing until LEDs flash alternatively LED1+LED3 => LED2+LED4 => LED1+LED3, etc. - Release reset button - The device starts a TFTP server at 192.168.1.20 - Set a static IP on the computer (e.g., 192.168.1.21/24) - Upload via tftp the factory image: $ tftp 192.168.1.20 tftp> bin tftp> trace tftp> put openwrt-ath79-generic-xxxxx-ubnt_powerbridge-m-squashfs-factory.bin Signed-off-by: Vieno Hakkerinen <vieno@hakkerinen.eu>
* ipq40xx: fix ethernet vlan double taggingJohn Crispin2020-07-142-11/+36
| | | | | | | | As the the SoC uses implicit vlan tagging for dual MAC support, the offload feature breaks when using double tagging. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: John Crispin <john@phrozen.org>
* ipq40xx: merge all ar40xx patches into one single patchJohn Crispin2020-07-142-30/+22
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ipq806x: really fix aliases node for Qualcomm IPQ8064/DB149Adrian Schmutzler2020-07-142-2/+12
| | | | | | | | | | | | | | | Having looked at this again, it appears that only gsbi2_serial is actually enabled for this device, so the entry in the broken aliases node was correct. Therefore, this needs to set its own serial0 instead of inheriting "serial0 = &gsbi4_serial;" from DTSI. Do this with the correctly named aliases node now. Fixes: c83f7b6d217f ("ipq806x: fix aliases node name for Qualcomm IPQ8064/DB149") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: use consistent DT labels for gsbiX_serialAdrian Schmutzler2020-07-142-4/+4
| | | | | | | | | | Kernel uses the label gsbiX_serial, so let's adjust our labels to this naming scheme. This is cosmetic, and actually only already existing gsbi4_serial has been used at all. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: fix aliases node name for Qualcomm IPQ8064/DB149Adrian Schmutzler2020-07-142-11/+1
| | | | | | | | | | | | | | | | | | | | | | | This device uses a node incorrectly named "alias" instead of "aliases" since it was introduced. Remove it without replacement, as the definitions in it don't seem to be required anyway: The serial0 definition has never been effective anyway and this would be the only device deviating from the common setting "serial0 = &gsbi4_serial;" for ipq8064. (So, maybe the wrong node prevented us from finding out about the wrong serial definition?) The mdio-gpio0 alias was supposed to be removed in d2a2eb7e48f6 anyway, the redundant definition in the alias node was just overlooked back then. Fixes: 0fd202f3e563 ("ipq806x: add db149 dts files") Fixes: d2a2eb7e48f6 ("ipq806x: replace caf nss-gmac driver by upstream stmmac") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: use rgmii-id instead of rgmii in ubnt,lap-120Roger Pueyo Centelles2020-07-131-3/+2
| | | | | | | | | | | Since commit 6f2e1b7485 (ath79: disable delays on AT803X config init) the incoming incoming traffic on the ubnt,lap-120 devices Ethernet port was not making it through. Using rgmii-id instead of rgmii (same configuration as ubnt,litebeam-ac-gen2) fixes it. Fixes FS#2893. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ramips: add support for D-Link DIR-878 A1Mathieu Martin-Borret2020-07-133-1/+198
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: MT7621AT RAM: 128MB Flash: 16MB NOR SPI flash WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz) LAN: 5x1000M Firmware layout is Uboot with extra 96 bytes in header Base PCB is AP-MTKH7-0002 LEDs Power Green,Power Orange,Internet Green,Internet Orange LEDs "2.4G" Green & "5G" Green connected directly to wifi module Buttons Reset,WPS,WIFI Flashing instructions: Upload image via emergency recovery mode Push and hold reset button (on the back of the device) until power led starts flashing (about 10 secs or so) while powering the device on. Give it ~30 seconds, to boot the recovery mode GUI Connect your client computer to LAN1 of the device Set your client IP address manually to 192.168.0.2 / 255.255.255.0. Call the recovery page for the device at http://192.168.0.1 Use the provided emergency web GUI to upload and flash a new firmware to the device. Some browsers/OS combinations are known not to work, so if you don't see the percentage complete displayed and moving within a few seconds, restart the procedure from scratch and try anoher one, or try the command line way. Alternative method using command line on Linux: curl -v -i -F "firmware=@openwrt-xxxx-squashfs-factory.bin" 192.168.0.1 Signed-off-by: Mathieu Martin-Borret <mathieu.mb@protonmail.com> [use of generic uimage-padhdr in image generation code] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: mtdsplit_uimage: add SGE parserMathieu Martin-Borret2020-07-131-0/+38
| | | | | | | Adding SGE parser for SGE (T&W) Shenzhen Gongjin Electronics to add 96 bytes padding the the firmware image Signed-off-by: Mathieu Martin-Borret <mathieu.mb@protonmail.com>
* rockchip: don't disable timer LED triggerDavid Bauer2020-07-131-1/+0
| | | | | | | | The timer LED trigger is enabled in all targets (except for lantiq xway-legacy). It's necessary for the OpenWrt preinit LED pattern to work. Signed-off-by: David Bauer <mail@david-bauer.net>
* rockchip: use downstream GPIO button implementationDavid Bauer2020-07-132-2/+1
| | | | | | | | Use the OpenWrt netlink GPIO button implementation to forward button presses to procd. This is necessary to make failsafe-mode access using a button possible. Signed-off-by: David Bauer <mail@david-bauer.net>
* bcm47xx: disable image for Linksys WRT160n v3Adrian Schmutzler2020-07-131-0/+1
| | | | | | | | | | | | The device can only hold 3.6 MB, but newer images (since 18.06) are bigger, so flashing a new version fails. This disables default build for this device based on the bug report referenced below. Fixes: FS#1963 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: consolidate Netgear devices for mt7628Adrian Schmutzler2020-07-137-283/+151
| | | | | | | | | | | | | | | This creates a common DTSI and shared image definition for the relatively similar Netgear devices for mt7628 platform. As a side effect, this raises SPI flash frequency for the R6120, as it's expected to work there as well if it works for R6080 and R6020. Based on the data from the other devices, it also seems probable the 5g MAC address for R6120 could be extracted from the caldata, and the mtd-mac-address there could be dropped. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: fix dsa binding for TP-Link TL-WR941ND v2Chuanhong Guo2020-07-122-13/+9
| | | | | | | | | upstream changed dt-bindings for marvell 88e6060 to use mdio-device and dropped support for legacy bindings. fix it in our local dts. Fixes: FS#2524 Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: qihoo,c301: use phy-supply for usb vbusChuanhong Guo2020-07-121-2/+2
| | | | | | | | Linux phy subsystem provides support for a phy regulator defined via phy-supply property. Use it to turn on usb power only when usb is probed. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* mvebu: add support for MACCHIATObin Single ShotTomasz Maciej Nowak2020-07-123-6/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for Marvell MACCHIATObin Single Shot, cortex-a72 based Marvell ARMADA 8040 Community board. Single Shot was broken as the device tree is different on the Double Shot Board. Specifications: - Quad core Cortex-A72 (up to 2GHz) - DDR4 DIMM slot with optional ECC and single/dual chip select support - Dual 10GbE (1/2.5/10GbE) SFP+ 2.5GbE (1/2.5GbE) via SFP 1GbE via copper - SPI Flash - 3 X SATA 3.0 connectors - MicroSD connector - eMMC - PCI x4 3.0 slot - USB 2.0 Headers (Internal) - USB 3.0 connector - Console port (UART) over microUSB connector - 20-pin Connector for CPU JTAG debugger - 2 X UART Headers - 12V input via DC Jack - ATX type power connector - Form Factor: Mini-ITX (170 mm x 170 mm) More details at http://macchiatobin.net Installation: Write the Image to your Micro SD Card and insert it in the MACCHIATObin Single Shot SD Card Slot. In the U-Boot Environment: 1. reset U-Boot environment: env default -a saveenv 2. prepare U-Boot with boot script: setenv bootcmd "load mmc 1:1 0x4d00000 boot.scr; source 0x4d00000" saveenv or manually (hanging lines indicate wrapped one-line command): setenv fdt_name armada-8040-mcbin-singleshot.dtb setenv image_name Image setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr $image_name;ext4load mmc 1:1 $fdt_addr $fdt_name;setenv bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti $kernel_addr - $fdt_addr' saveenv On newer Bootloaders (18.12) the Variables have been changed, use: setenv fdt_name armada-8040-mcbin-singleshot.dtb setenv image_name Image setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr_r $image_name;ext4load mmc 1:1 $fdt_addr_r $fdt_name;setenv bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti $kernel_addr_r - $fdt_addr_r' Reported-by: Alexandra Alth <alexandra@alth.de> Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> Tested-by: Alexandra Alth <alexandra@alth.de> [add specs and installation as provided by Alexandra Alth] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: consolidate recipes with uimage_padhdrAdrian Schmutzler2020-07-113-13/+8
| | | | | | | | | | | There are already two very similar recipes using uimage_padhdr in ramips target, and a third one is about to be added. Make the recipe more generic, so redefinitions are not necessary anymore. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Bjørn Mork <bjorn@mork.no> [Zyxel WAP6805]
* mvebu: fix support for Marvell 8040 MACCHIATOBinAdrian Schmutzler2020-07-114-5/+19
| | | | | | | | | | | | | | | | | | | | | | Between kernels 4.20 and 5.0, a new variant of this board has been introduced ("Single Shot"), and the existing one has been renamed with the appendix "Double Shot". [1] This also adjusted the first compatible in the list: marvell,armada8040-mcbin -> marvell,armada8040-mcbin-doubleshot This patch updates the OpenWrt implementation of this device by adjusting the relevant references to that compatible (i.e., our board name). To still provide support for 4.19 with our setup, this adds a small patch to change the compatible there as well. [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=b1f0bbe2700051886b954192b6c1751233fe0f52 Cc: Tomasz Maciej Nowak <tomek_n@o2.pl> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* bcm63xx: R5010UNv2: fix flash partitions for 16MB flashDaniel González Cabanelas2020-07-111-5/+5
| | | | | | | | | | | The router Nucom R5010UN v2 has the partitions defined for a 8MB flash, but the flash chip is 16MB size. We are wasting half of the flash. Fix it and use generic names for partitions. Fixes: 474cde61234c ("brcm63xx: probe SPI flash through DT") Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
* build: improve ccache supportRoman Yeryomin2020-07-112-7/+3
| | | | | | | | | | | | | | | | | | Set CCACHE_DIR to $(TOPDIR)/.ccache and CCACHE_BASEDIR to $(TOPDIR). This allows to do clean and dirclean. Cache hit rate for test build after dirclean is ~65%. If CCACHE is enabled stats are printed out at the end of building process. CCACHE_DIR config variable allows to override default, which could be useful when sharing cache with many builds. cacheclean make target allows to clean the cache. Changes from v1: - remove ccache directory using CCACHE_DIR variable - remove ccache leftovers from sdk and toolchain make files - introduce CONFIG_CCACHE_DIR variable - introduce cacheclean make target Signed-off-by: Roman Yeryomin <roman@advem.lv>
* ramips: mt7621: refactor set affinity scriptDENG Qingfang2020-07-111-19/+7
| | | | | | | | The current one only looks for mt76x2e and mt7603e, and does not work for 2 or more same Wi-Fi chips. Refactor the script to cover those cases. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* layerscape: define IMAGE_SIZE and LS_SYSUPGRADE_IMAGE_SIZEYangbo Lu2020-07-113-10/+18
| | | | | | | | | Define 64m IMAGE_SIZE for flash firmware.bin since the flash size is 64MB. Define 48m LS_SYSUPGRADE_IMAGE_SIZE for flash sysupgrade.bin which contains maximum 16MB kernel and 32MB rootfs according to memory map. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: support sysupgrade for SD card ext4 rootfsYangbo Lu2020-07-114-6/+141
| | | | | | Support sysupgrade for SD card ext4 rootfs. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: support sysupgrade for squashfs rootfsYangbo Lu2020-07-113-7/+29
| | | | | | | Support sysupgrade for all Layerscape boards with squashfs rootfs. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: fix board name for SD card bootYangbo Lu2020-07-111-0/+13
| | | | | | | | | Many Layerscape boards support both flash boot and SD card boot. And different firmware and sysupgrade.bin are built for the two boot methods. To identify them, a fix could be done on board name by adding a postfix "-sdboot" for SD card boot. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: add compatible for board ls1043ardbYangbo Lu2020-07-111-0/+28
| | | | | | Backport a dts patch which added compatible for ls1043ardb. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: convert to squashfs rootfs for QSPI NOR bootYangbo Lu2020-07-111-17/+5
| | | | | | | | | | | There had been an issue in Layerscape QSPI driver for very long time, which made squashfs,jffs2 rootfs not work on QSPI NOR. And the ubifs had been used as a workaround. Now the issue has been fixed. So convert to use squashfs,jffs2 rootfs on QSPI NOR for Layerscape boards (LS1012ARDB/LS1046ARDB/ LS1088ARDB), and update u-boot bootargs for booting. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* toolchain/wrapper.sh: fix remaining shellcheck warningsPetr Štetiar2020-07-111-8/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes following warnings: In target/toolchain/files/wrapper.sh line 18: REALNAME=$(readlink -f $0) ^-- SC2086: Double quote to prevent globbing and word splitting. -- In target/toolchain/files/wrapper.sh line 20: REALNAME_BASE=$(basename $REALNAME) ^-------^ SC2086: Double quote to prevent globbing and word splitting. -- In target/toolchain/files/wrapper.sh line 21: REALNAME_DIR=$(dirname $REALNAME) ^-------^ SC2086: Double quote to prevent globbing and word splitting. -- In target/toolchain/files/wrapper.sh line 74: exec $TARGET_TOOLCHAIN_TRIPLET-$BINARY.bin $GCC_SYSROOT_FLAGS $TARGET_FUNDAMENTAL_CFLAGS $TARGET_ROOTFS_CFLAGS "$@" ^-----------------------^ SC2086: Double quote to prevent globbing and word splitting. -- In target/toolchain/files/wrapper.sh line 77: exec $TARGET_TOOLCHAIN_TRIPLET-$BINARY.bin $LD_SYSROOT_FLAGS $TARGET_FUNDAMENTAL_LDFLAGS "$@" ^-----------------------^ SC2086: Double quote to prevent globbing and word splitting. -- In target/toolchain/files/wrapper.sh line 80: exec $TARGET_TOOLCHAIN_TRIPLET-$BINARY.bin $TARGET_FUNDAMENTAL_ASFLAGS "$@" ^-----------------------^ SC2086: Double quote to prevent globbing and word splitting. -- In target/toolchain/files/wrapper.sh line 83: exec $TARGET_TOOLCHAIN_TRIPLET-$BINARY.bin "$@" ^-----------------------^ SC2086: Double quote to prevent globbing and word splitting. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* toolchain/wrapper.sh: Replace read with read -rRosen Penev2020-07-111-1/+1
| | | | | | | | Without -r, backslashes would get mangled. Found with shellcheck. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: kernel: fix awake-rt305x-dwc2 patchAlexey Dobrovolsky2020-07-111-7/+7
| | | | | | | | | | | | | At this point in v5.4 kernel we cannot use dwc2_readl() and dwc2_writel() since they rely on the value hsotg->needs_byte_swap which cannot be obtained before the controller wakes up. We should use readl() and writel() to wake up the controller before calling dwc2_check_core_endianness(). Fixes: 6be0da90a165 ("ramips: refresh patches") Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com> [fixed Fixes: tag] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kirkwood: add support for Check Point L-50Pawel Dembicki2020-07-117-0/+589
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Check Point L-50 from 600/1100 series routers. Specification: -CPU: Marvell Kirkwood 88F6281 1200MHz -RAM: 512MB -Flash: NAND 512MB -WiFi: mPCIe card based on Atheros AR9287 b/g/n -WAN: 1 Gigabit Port (Marvell 88E1116R PHY) -LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+4)) -USB: 2x USB2.0 -Express card slot -SD card slot -Serial console: RJ-45 115200 8n1 -Unsupported DSL Known issues: -DSL not supported -Expresscard not tested Installation: Step one -> backup: make backup u-boot and env for revert stock posibility make backup dsl_mac_addr, dmz_mac_addr, eth1addr, ethaddr and all lanX_mac_addr Step two -> Use kwboot tool to upload openwrt u-boot to RAM: run kwboot: "kwboot -B 115200 /dev/ttyUSB0 -b u-boot.kwb -p -t" end start u-boot Step three -> Restore macs (e.g. below): setenv eth1addr 00:1C:XX:XX:XX:6C setenv ethaddr 00:1C:XX:XX:XX:6B setenv lan1_mac_addr 00:1C:XX:XX:XX:6C setenv lan2_mac_addr 00:1C:XX:XX:XX:6D setenv lan3_mac_addr 00:1C:XX:XX:XX:6E setenv lan4_mac_addr 00:1C:XX:XX:XX:6F setenv lan5_mac_addr 00:1C:XX:XX:XX:70 setenv lan6_mac_addr 00:1C:XX:XX:XX:71 setenv lan7_mac_addr 00:1C:XX:XX:XX:72 setenv lan8_mac_addr 00:1C:XX:XX:XX:73 setenv dmz_mac_addr 00:1C:XX:XX:XX:74 setenv dsl_mac_addr 00:1C:XX:XX:XX:75 Step four -> flash u-boot: mw 0x0800000 0xffff 0x100000 nand erase 0x0 100000 tftp 0x0800000 openwrt-kirkwood-l50-u-boot.kwb nand write 0x0800000 0x0 0x100000 saveenv Step five -> run initramfs image: tftpboot 0x02000000 openwrt.bin; bootm 0x02000000; Step six -> install sysupgrade OpenWrt image: copy to /tmp/ sysupgrade image run sysupgrade Back to stock: Restore original u-boot end env. Install factory image via stock u-boot. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kernel: bump 5.4 to 5.4.51John Audia2020-07-114-67/+6
| | | | | | | | | | | | | | | | | | | | | update via update_kernel.sh -v -u 5.4 Removed upstreamed patches: 350-MIPS-Add-missing-EHB-in-mtc0-mfc0-sequence-for-DSPen.patch Script refreshed patches: 902-debloat_proc.patch 904-debloat_dma_buf.patch Attempted merge conflict in following patches: 0024-MIPS-lantiq-revert-DSA-switch-driver-PMU-clock-chang.patch Build system: x86_64 Build tested: ipq806x (Netgear R7800) Signed-off-by: John Audia <graysky@archlinux.us> [fixed sha256sum of the tarball] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq806x: enable Linksys EA8500 eth1 interfacePawel Dembicki2020-07-113-1/+3
| | | | | | | | | | | | | At this moment Linksys EA8500 uses only eth0. This patch change switch registers, which allow to use eth1 as lan and eth0 as wan. The method work with similar Linksys EA7500V1 and it work with EA8500. Suggested-by: Sungbo Eo <mans0n@gorani.run> Tested-by: Brian Onn <brian.a.onn@gmail.com> Tested-by: Adrian Panella <ianchi74@outlook.com> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ath79: disable TP-Link TL-WR941ND v2Adrian Schmutzler2020-07-111-1/+1
| | | | | | | | | | | | | The support for this device's Marvell MV88E6060 switch has been reported to be broken with kernels 4.19/5.4 (see bug report). Since this a 4/32 device and it has been confirmed to be working with stable 19.07 release (kernel 4.14), and since fixing it does not seem trivial, let's just disable it in master. Fixes: FS#2524 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Netgear R6020Tim Thorpe2020-07-104-0/+194
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Netgear R6020, aka Netgear AC750. The R6020 appears to be the same hardware as the Netgear R6080, aka Netgear AC1000, but it has a slightly different flash layout, and no USB ports. Specification: SoC: MediaTek MT7628 (580 MHz) Flash: 8 MiB RAM: 64 MiB Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E) LAN speed: 10/100 LAN ports: 4 WAN speed: 10/100 WAN ports: 1 UART (57600 8N1) on PCB MAC addresses based on vendor firmware: LAN *:88 0x4 WAN *:89 WLAN2 *:88 0x4 WLAN5 *:8a 0x8004 The factory partition might have been corrupted beforehand. However, the comparison of vendor firmware and OpenWrt still allowed to retrieve a meaningful assignment that also matches the other similar devices. Installation: Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet cable to connect to LAN port 1 of the R6020, and power the R6020 off. From the connected workstation, run `nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6020-squashfs-factory.img`, replacing eth0 with the appropriate interface (can be identified by running `nmrpflash -L`). Then power on the R6020. After flashing has finished, power cycle the R6020, and it will boot into OpenWRT. Once OpenWRT has been installed, subsequent flashes can use the web interface and sysupgrade files. Signed-off-by: Tim Thorpe <timfthorpe@gmail.com> [slightly extend commit message, fix whitespaces in DTS, align From: with Signed-off-by] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* lantiq: set correct gphy pins for Zyxel P-2812Willem van den Akker2020-07-102-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | This fixes the gphy LED pins for Zyxel P-2812 devices. The have been accidentally altered during a tidy-up operation (see Fixes: below). No ports were available, dmesg reported: [ 0.658577] pinctrl-xway 1e100b10.pinmux: pin io5 already requested by 1e100bb0.stp; cannot claim for 1e108000.eth [ 0.667566] pinctrl-xway 1e100b10.pinmux: pin-5 (1e108000.eth) status -22 [ 0.685238] lantiq,xrx200-net 1e108000.eth: Error applying setting, reverse things back [ 0.693270] lantiq,xrx200-net: probe of 1e108000.eth failed with error -22 Fixes: FS#3188 Fixes: 660200e53d62 ("lantiq: dts: assign the GPHY LED pins to the Ethernet controller node") Suggested-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Willem van den Akker <wvdakker@wilsoft.nl> [commit message facelift] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mediatek: fix bashism in gen_banana_pi_img.shDavid Woodhouse2020-07-091-1/+1
| | | | | | | | There was a bashism in the script. This fixes the script so that it doesn't actually require bash, and can be run with any POSIX shell as its shebang suggests. Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* mediatek: re-add u3phy2 phy-switch patchSungbo Eo2020-07-091-0/+66
| | | | | | | | | This patch is required for pcie@2,0 in mt7623 to work. The patch was originally added in kernel 4.14, but it has not been ported to 4.19 and later. Fixes: FS#3217 Tested-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* mediatek: do not create device nodes in uci-defaults scriptSungbo Eo2020-07-091-16/+5
| | | | | | | | | Since commit 298814e6be76 ("base-files: config_generate: split macaddr with multiple ifaces") uci MAC address setup will create a device node for each member iface. But this script might override the device nodes and interfere with the MAC address setup. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-06 19:31:18 +0000