aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for TP-Link TL-WA850RE v2Adrian Schmutzler2020-01-224-1/+181
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender, based on Qualcomm/Atheros QCA9533 v2. Short specification: - 550/391/195 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 32 MB of RAM (DDR1) - 4 MB of FLASH - 2T2R 2.4 GHz - 2x internal antennas (embedded on PCB) - 9x LED (all can be turned off with GPIO15), 2x button - UART (J3) header on PCB Flash instruction: use "factory" image directly in vendor GUI. Warning: this device does not include any kind of recovery mechanism in the bootloader and disassembling process is not trivial. You can access vendor firmware over serial line using: - login: root - password: sohoadmin Stock firmware uses label MAC address for WiFi and same with local bit set for ethernet. Since this is difficult to reproduce with the toolset of OpenWrt, we just keep both ethernet and WiFi to the same address here. This is the first tiny device with tplink-safeloader in ath79. Firmware partition is only 3648k and thus even smaller than for the tplink-4m(lzma) devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: use dynamic partitioning for TP-Link TL-WA850RE v2Adrian Schmutzler2020-01-221-1/+1
| | | | | | | This moves the TP-Link TL-WA850RE v2 to dynamic partitioning and will allow to use this for ath79 as well. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* generic at803x: remove unneeded patchesDavid Bauer2020-01-223-236/+0
| | | | | | | | | | | | | | | | | | | | | | - Remove the "RGMII TX delay fixup" hack and the associated DT-property. It was never used in a DT-based platform and solved a problem which can be mitigated by using correct delays on the MAC side. - Remove the patch to enable platform-data support for the at803x driver. It was only used by ar71xx which does not (and never will) support kernel 4.19 or later. - Remove the SmartEEE DT-configuration patch. As explained previously, this patch never disabled the Atheros SmartEEE implementation, but rather "standard" EEE. This can be done on device-tree compatible platforms by adding the "eee-broken-1000t" or "eee-broken-100tx" properties to the PHY node. As all usages of the old properties are migrated, this patch can be removed. Signed-off-by: David Bauer <mail@david-bauer.net> Acked-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: use upstream properties to disable EEEDavid Bauer2020-01-224-4/+8
| | | | | | | | | | | | | The hack-patch which introduced the "at803x-disable-smarteee" for disabling SmartEEE did in fact not disable SmartEEE but rather disabled 802.3az "standard" EEE. This can be done by using the upstream properties "eee-broken-100tx" and "eee-broken-1000t". EEE is then disabled by the PHY subsystem. Tested on devolo WiFi pro 1200e. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for TP-Link TL-WA850RE v1Adrian Schmutzler2020-01-225-0/+182
| | | | | | | | | | | | | | | | | | | | | | This ports support for the TL-WA850RE v1 range extender from ar71xx to ath79. Specifications: Board: AP123 / AR9341 rev. 3 Flash/RAM: 4/32 MiB CPU: 535 MHz WiFi: 2.4 GHz b/g/n Ethernet: 1 port (100M) Flashing instructions: Upload the factory image via the vendor firmware upgrade option. Recovery: Note that this device does not provide TFTP via ethernet like many other TP-Link devices do. You will have to open the case if you require recovery beyond failsafe. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: sfp: re-attempt probing for phyJonas Gorski2020-01-214-0/+344
| | | | | | | | | Add patches retrying to probe the PHY to restore support for PHYs taking longer to initialize without breaking modules without PHYs. Patches taken from http://git.armlinux.org.uk/cgit/linux-arm.git/log/?h=phy Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* kernel: sfp: add two fixes submitted to upstreamJonas Gorski2020-01-212-0/+72
| | | | | | Add two small fixes for SFP that were submitted upstream. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* mvebu: add uDPU update patchesRussell King2020-01-213-0/+98
| | | | | | | | | | | | Update the uDPU kernel support, fixing a number of issues: * make ethernet work again by adding comphy definitions * slow the I2C bus to give it more chance of actually working * the SFP cages are designed to support up to 3W modules, which would be prevented from initialising without this patch. Signed-off-by: Russell King <linux@armlinux.org.uk> [jonas.gorski: rename to mvebu, refresh patches] Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* kernel: add SFP support for Methode DM7052 NBASE-T moduleRussell King2020-01-2117-4/+1919
| | | | | | | | | | Add support for Methode DM7052 NBASE-T module to OpenWRT. These patches are taken from my "phy" branch, and will be sent for the next kernel merge window. Signed-off-by: Russell King <linux@armlinux.org.uk> [jonas.gorski: move patches to pending, refresh patches] Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* kernel: add backported phy/phylink/sfp patchesRussell King2020-01-2143-0/+4575
| | | | | | | | | | Backport the phy/phylink/sfp patches currently queued in netdev or in mainline necessary to support GPON popular modules, specifically to support Huawei and Nokia GPON modules. Signed-off-by: Russell King <linux@armlinux.org.uk> [jonas.gorski: include kernel version in file names, refresh patches] Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* kernel: move phylink patches from mvebu to genericRussell King2020-01-212-0/+0
| | | | | | | | | Move two phylink patches from mvebu to generic, so that everyone can benefit from them. Signed-off-by: Russell King <linux@armlinux.org.uk> [jonas.gorski: add kernel version to file names] Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* kernel: remove obsolete phylink/SFP patchesRussell King2020-01-216-653/+0
| | | | | | | | | | | | | | | Remove the old phylink/SFP patches from the OpenWRT build; these will be updated with a new set in subsequent. 450-reprobe_sfp_phy is also removed for several reasons: 1) it is not in mainline. 2) it breaks copper modules that do not have a PHY. 3) it makes backporting the current patch set harder. Discussion is ongoing with the patch author for a mainline Linux kernel patch for this. Signed-off-by: Russell King <linux@armlinux.org.uk>
* ath79: remove usused TPLINK_BOARD_NAME variable for DEVICE_VARSAdrian Schmutzler2020-01-211-1/+1
| | | | | | | | | | | | | | TPLINK_BOARD_NAME has been renamed to TPLINK_BOARD_ID a long time ago (7d6c63d87542: "build: rename TPLINK_BOARD_NAME to TPLINK_BOARD_ID" for ar71xx), and before introducing ath79 target at all. TPLINK_BOARD_NAME seems to have been introduced into ath79 target only by mistake. It has never been used. Remove it. Fixes: 53c474abbdfe ("ath79: add new OF only target for QCA MIPS silicon") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* Revert "kernel: mtd: Make subpartitions inherit parent's access mode"Petr Štetiar2020-01-212-120/+0
| | | | | | | | | | | | | This reverts commit de80424f706682e8bba27c60bcd2a9c1b4a5e875 which needs more work and testing as it broke at least jffs2 overlays at least on ath79 platform, marking them as read-only, thus unusable: jffs2_build_filesystem(): erasing all blocks after the end marker... jffs2: Erase at 0x009e0000 failed immediately: -EROFS. Is the sector locked? Ref: http://lists.infradead.org/pipermail/openwrt-devel/2020-January/021344.html Reported-by: Steve Brown <sbrown@ewol.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* zynq: derive DEVICE_DTS from device definition nameAdrian Schmutzler2020-01-211-4/+1
| | | | | | | | | | In zynq target, the DEVICE_DTS variable is always set consistent with the model part of the device definition name. This patch replaces the redundant definitions for the individual devices with a common recipe. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: split base-files across subtargetsAdrian Schmutzler2020-01-2117-129/+251
| | | | | | | | | | | | | For the mvebu target in particular, there is a lot of files in base-files that are only relevant for one subtarget. Improve overview and reduce size per subtarget by moving/splitting base-files depending on the subtarget they belong to. While at it, consolidate 01_leds by using the model part of the board name as variable. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: use SOC to derive DEVICE_DTSAdrian Schmutzler2020-01-213-7/+8
| | | | | | | | | | | | This introduces the SOC variable to mvebu target to derive some of the DEVICE_DTS variables based on the SOC prefix and the device definition name. Since DTS names and compatible are inconsistent also in the kernel for this target, the scheme cannot be applied to all devices, though. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: move subtarget image Makefile switch to parent MakefileAdrian Schmutzler2020-01-214-12/+8
| | | | | | | | | | This moves the if conditions for choosing which image Makefiles are used to the parent image/Makefile. It seems more convenient to have "codeflow" in the parent while the subtarget-specific files only contain the definitions. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: add support for TP-Link TL-MR6400Enrico Mioso2020-01-214-0/+189
| | | | | | | | | | | | | | | | | | | | | | | | | | This device is an LTE router supported in ar71xx so far. As per original commit, hardware specifications (v1.0 EU): - SoC: QCA9531 - Flash: Winbond W25Q64FV (8MiB) - RAM: EtronTech EM6AB160TSE-5G (64MiB) - Wireless: SoC platform only (2.4GHz b/g/n, 2x internal antenna) - Ethernet: 2NIC (3x100M + 1x100M) - WWAN: TP-LINK LTE MODULE (2x external detachable antenna) - Power: DC 12V 1A Flashing instructions: You can flash via tftp recovery (serve factory image as /mr6400_tp_recovery.bin on 192.168.0.66/24, connect to any ethernet port and power on device while holding the reset button). Flashing via OEM web interface does not work. Known issues: - LTE module does not always come up during boot (showing USB enumeration errors). Similar behavior has been reported at least from one user for ar71xx, too. Turning USB off and on again will serve as a workaround. - eth0 (LAN) always shows carrier as 1 even if no cable is plugged in (this works "correctly" on ar71xx) Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com> [several adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Filip Moc <lede@moc6.cz>
* ar71xx: ubnt-rocket-m-ti: fix RSSI LED definitionsLech Perczak2020-01-212-6/+8
| | | | | | | | | | | | | | | | When mapping for RSSI LEDs was defined for interface wlan0 on Ubiquiti Rocket M Titanium, it missed connection to actual interface. Therefore create the mapping to interface, so RSSI LEDs work without additional configuration, after starting rssileds service. While at that, split RSSI into ~equal intervals for 6 LEDs, and remove coefficients needed for PWM LEDs, as this board does not support PWM LEDs. Finally, for complete support, enable 'rssileds' package in per-device rootfs, so the indicator works out of box. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: fix SUPPORTED_DEVICES for WNDR4300 and WNDR3700v4Michal Cieslakiewicz2020-01-211-2/+0
| | | | | | | | | | Kernel partition increase to 4 MiBs for Netgear WNDR3700v4 and WNDR4300 routers breaks sysupgrade image compatibility with ar71xx builds. Therefore, SUPPORTED_DEVICES variable has to be removed for both devices from target makefile. Reported-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* kernel: mtd: Make subpartitions inherit parent's access modeBruno Pena2020-01-202-0/+120
| | | | | | | | | | | | | | | | | | | | | | | Currently it's not possible to effectively mark a "firmware" partition as read-only. The sub-partitions "kernel", "rootfs" and "rootfs_data" are always created as read-write (ignoring the parent access mode). This patch enforces the access mode of sub-partitions to match the parent partition, which is useful for recovery images that are meant to be fully read-only to avoid accidental damage from end-user. An example of such implementation (read-only firmware image) is the recovery image used on the Zsun-SD100 [1]. Please note the related patch for fstools [2] to enable this read-only concept. [1] https://github.com/brunompena/zsun-resources [2] http://lists.infradead.org/pipermail/openwrt-devel/2020-January/021043.html Signed-off-by: Bruno Pena <brunompena@gmail.com> [removed already obsolete 4.9 kernel patch] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 4.19 to 4.19.97Koen Vandeputte2020-01-202-2/+2
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.166Koen Vandeputte2020-01-202-2/+2
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.96Koen Vandeputte2020-01-203-4/+4
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.165Koen Vandeputte2020-01-201-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.95Koen Vandeputte2020-01-2014-29/+29
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.164Koen Vandeputte2020-01-2026-110/+110
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* brcm47xx: fix switch port order for Netgear WN2500RP V1Walter Sonius2020-01-201-0/+5
| | | | | | | | | | | | | The Netgear WN2500RP V1 switch0 already works for LAN however the port order for the LAN ports is inverted. Correct physical port order watched from the back of the device is: 4 / 3 / 2 / 1 WAN port is absent on this device and therefore removed from switch config. Signed-off-by: Walter Sonius <walterav1984@gmail.com> [move block to maintain alphabetic sorting] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: apply LED_POLARITY rt3050-esw on MT7628AN/MT7688Maximilian Pachl2020-01-191-0/+4
| | | | | | | | | | | The device tree property "mediatek,led_polarity" is ignored for MT7628AN and MT7688. According to the datasheet both SoCs have the matching register. Therefore the property should be applied on these two devices as well. Signed-off-by: Maximilian Pachl <m@ximilian.info> Reviewed-by: Sungbo Eo <mans0n@gorani.run> Tested-by: Sungbo Eo <mans0n@gorani.run>
* kirkwood: fix HDD LED labels for Zyxel NSA325 in 01_ledsStephan Knauss2020-01-181-2/+2
| | | | | | | | | Change the LED labels for hdd1/hdd2 in 01_leds to match their counterpart in DTS. Signed-off-by: Stephan Knauss <openwrt@stephans-server.de> [improve commit title and message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* brcm47xx: fix switch port order for Netgear WNR3500 V2Walter Sonius2020-01-181-0/+1
| | | | | | | | | | | The Netgear WNR3500 V2 switch0 already works for WAN/LAN however the port order for the LAN ports is inverted. Correct physical port order watched from the back of the device is: Internet / 4 / 3 / 2 / 1 this resembles the Linksys E3000 V1. Verfied with imagebuilder edit FILES=/etc/board.d/01_network Signed-off-by: Walter Sonius <walterav1984@gmail.com>
* ramips: add support for TP-Link RE305 v1Steffen Förster2020-01-183-0/+175
| | | | | | | | | | | | | | | | | | | | | | Specification: SoC: MediaTek MT7628AN RAM: 64MiB Flash: 8MiB Wifi: - 2.4GHz: MT7628AN - 5GHz: MT7612EN LAN: 1x 10/100 Mbps Flash instructions: Flash factory image through stock firmware WEB UI. Back to stock is possible by using TFTP and stripping down the Firmware provided by TP-Link to a initramfs. The flash space between 0x650000 and 0x7f0000 is blank in the stock firmware so I left it out as well. Signed-off-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
* kernel: remove further obsolete kernel version switchesSungbo Eo2020-01-181-6/+2
| | | | | | | | Most of the kernel version switches below 4.14 were removed in commit 97940f876616 ("kernel: remove obsolete kernel version switches"), but some of them still remained. Remove them now. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ath79: add led_ prefix for Phicomm K2T LED labelAdrian Schmutzler2020-01-181-5/+5
| | | | | | | Using the led_ prefix for the node label is now common in ath79, so also apply it here. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: use rssihigh LED instead of WAN LED for status indicationAdrian Schmutzler2020-01-182-10/+10
| | | | | | | | | | | | Using the LED of network interfaces for status (boot/failsafe/...) indication is somewhat misleading, as the blinking might be mistaken for network activity. This uses rssi LEDs instead, which do not blink normally and thus are less ambiguous. The rssihigh LED has also been used consistently for the TP-Link CPE devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* octeon: remove redundant network setupAdrian Schmutzler2020-01-181-4/+0
| | | | | | No need to have specific setup when default case does the same. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: rt305x: remove unnecessary mediatek,portmapSungbo Eo2020-01-182-2/+0
| | | | | | | | | "#mediatek,portmap" is not a valid property name. If mediatek,portmap equals 0x0, then the esw driver ditches it and uses the default value, 0x3f. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: mt76x8: fix bogus mediatek,portmapSungbo Eo2020-01-1818-14/+62
| | | | | | | | | | | | | | | | | | | | | | | | | | | mt76x8 uses esw_rt3050 driver, which does not accept mediatek,portmap with string values. Convert the strings to integers to make it work. According to its switch setup, WRTnode 2P/2R have a WAN port at port 0, so the correct value should be 0x3e. tplink_8m.dtsi uses "llllw", but it does not match switch setups of any device using the DTSI. Remove it from the DTSI and add correct value to DTS for each device. These devices have a WAN port at port 0. Set the value to 0x3e. - tplink,archer-c20-v4 - tplink,archer-c50-v3 - tplink,tl-mr3420-v5 - tplink,tl-wr840n-v4 - tplink,tl-wr841n-v13 - tplink,tl-wr842n-v5 These devices have only one ethernet port. They don't need portmap setting. - tplink,tl-wa801nd-v5 - tplink,tl-wr802n-v4 - tplink,tl-wr902ac-v3 Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: mt7620/mt7621: remove invalid mediatek,portmapSungbo Eo2020-01-183-5/+3
| | | | | | | | | | mt7620 and mt7621 use mt7530 driver, which only accepts "llllw", "wllll", and "lwlll" values. According to its switch setup, Mi Router 3G v2 has a WAN port at port 4, so the correct value should be "llllw". Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: fix wps leds/btn for TP-Link TL-WA801ND v5Jan Alexander2020-01-171-4/+16
| | | | | | | | | | - fix color and active mode for existing wps led - add green wps led - add wps button Signed-off-by: Jan Alexander <jan@nalx.net> [wrap line] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix HiWiFi HC5962 status LEDDENG Qingfang2020-01-161-3/+4
| | | | | | | | | Match LED behavior to stock firmware: Red: booting White: running Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: fix HiWiFi HC5962 switch configurationDENG Qingfang2020-01-161-1/+4
| | | | | | HC5962 has only 3 LAN ports, switch port 0 is unused Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ath79: ar934x: use reset for usb-phy-analogJohann Neuhauser2020-01-151-2/+2
| | | | | | | | | | | | This was already available on ar71xx, but is missing on ath79. This solves the slow usb speed on TP-Link WDR3600/WDR4300 and similar, as reported in Flyspray [0], OpenWRT Forum [1] and GitHub PR [2]. [0] https://bugs.openwrt.org/index.php?do=details&task_id=2567 [1] https://forum.openwrt.org/t/usb-wdr4300-low-speed-on-external-storage/46794 [2] https://github.com/openwrt/openwrt/pull/964 Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ath79: phy-ar7200-usb: adapt old behavior of arch/mips/ath79/dev-usb.cJohann Neuhauser2020-01-151-6/+18
| | | | | | | | | | | | Do not put usb-phy into reset if clearing the usb-phy reset or setting the suspend_override has failed. Reorder (de)asserts like in arch/mips/ath79/dev-usb.c. Add an optional reset_control "usb-phy-analog", which is needed for ar934x SoCs like in the old mach-driver arch/mips/ath79/dev-usb.c. Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ar71xx/mikrotik: use ath10k-ct-smallbuffers for 64 MiB devicesThomas Nixon2020-01-151-1/+1
| | | | | | | | | | This image is only needed on one device (wAP AC); since this target is going to be removed anyway it doesn't make sense to add an extra "low RAM" image. Fixes OOM issues on RouterBoard wAP AC. Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
* ath79: use caldata partition label consistentlyAdrian Schmutzler2020-01-152-8/+8
| | | | | | | Change the caldata partition DTS node label to be consistent with the label property for some Netgear WNDR devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* malta: enable HighMem on MIPS32Aleksander Jan Bajkowski2020-01-152-0/+2
| | | | | | It allows to use more than 256MB memory on MIPS32. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* ath79: add support for Netgear WNDR4500 v3Michal Cieslakiewicz2020-01-155-5/+62
| | | | | | | | | | | | | | | | | | | This patch introduces support for Netgear WNDR4500v3. Router is very similar to WNDR4300v2 and is based on the same PCB. Information gathered from various Internet sources (including https://patchwork.ozlabs.org/patch/809227/) shows following differences to WNDR4300v2: * two USB 2.0 ports with separate LEDs * USB LEDs soldered to secondary pads * WPS and RFKILL buttons soldered to secondary pads * described as N900 device with 3x3:3 MIMO for 2.4GHz radio * power supply requirement is DC 12V 2.5A * vendor HW ID suffix differs in one digit * bigger chassis Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add support for Netgear WNDR4300 v2Michal Cieslakiewicz2020-01-156-5/+296
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch introduces support for Netgear WNDR4300v2. Specification ============= * Description: Netgear WNDR4300 v2 * Loader: U-boot * SOC: Qualcomm Atheros QCA9563 (775 MHz) * RAM: 128 MiB * Flash: 2 MiB SPI-NOR + 128 MiB SPI-NAND - NOR: U-boot binary: 256 KiB - NOR: U-boot environment: 64 KiB - NOR: ART Backup: 64 KiB - NOR: Config: 64 KiB - NOR: Traffic Meter: 64 KiB - NOR: POT: 64 KiB - NOR: Reserved: 1408 KiB - NOR: ART: 64 KiB - NAND: Firmware: 25600 KiB (see notes for OpenWrt) - NAND: Language: 2048 KiB - NAND: mtdoops Crash Dump: 128 KiB - NAND: Reserved: 103296 KiB * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8337) * Wireless: - 2.4 GHz b/g/n (internal) - 5 GHz a/n (AR9580) * USB: yes, 1 x USB 2.0 * Buttons: - Reset - WiFi (rfkill) - WPS * LEDs: - Power (amber/green) - WAN (amber/green) - WLAN 2G (green) - WLAN 5G (blue) - 4 x LAN (amber/green) - USB (green) - WPS (green) * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1 * Power supply: DC 12V 1.5A * MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2 Important Notes =============== 0. NOR Flash (2 MiB) is not touched by OpenWrt installation. 1. NAND Flash (128 MiB) layout under OpenWrt is changed as follows: all space is split between 4 MiB kernel and 124 MiB UBI areas; vendor partitions (language and mtdoops) are removed; kernel space size can be further expanded if needed; maximum image size is set to 25600k for compatibility reasons and can also be increased. 2. CPU clock is 775 MHz, not 750 MHz. 3. 5 GHz wireless radio chip is Atheros AR9580-AR1A with bogus PCI device ID 0xabcd. For ath9k driver to load successfully, this is overriden in DTS with correct value for this chip, 0x0033. 4. RFKILL button is wired to AR9580 pin 9 which is normally disabled by chip definition in ath9k code (0x0000F4FF gpio mask). Therefore 'qca,gpio-mask=<0xf6ff>' hack must be used for button to work properly. 5. USB port is always on, no GPIO for 5V power control has been identified. Installation ============ * TFTP recovery * TFTP via U-boot prompt * sysupgrade * Web interface Test build configuration ======================== CONFIG_TARGET_ath79=y CONFIG_TARGET_ath79_nand=y CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr4300-v2=y CONFIG_ALL_KMODS=y CONFIG_DEVEL=y CONFIG_CCACHE=y CONFIG_COLLECT_KERNEL_DEBUG=y CONFIG_IMAGEOPT=y Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>