aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* ep93xx: remove obsolete kernel version checkFelix Fietkau2015-01-241-7/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 44112
* x86: remove linux 3.3 supportFelix Fietkau2015-01-2413-1811/+0
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 44111
* build: drop obsolete kernel version dependenciesFelix Fietkau2015-01-241-1/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 44110
* kernel: remove linux 3.3 patches and configFelix Fietkau2015-01-24179-45292/+0
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 44109
* pxa: mark as brokenFelix Fietkau2015-01-241-1/+1
| | | | | | It still uses the long obsolete 3.3 kernel version SVN-Revision: 44108
* x86: mark the ep80579 subtarget as brokenFelix Fietkau2015-01-241-0/+1
| | | | | | | | It still uses the long obsolete 3.3 kernel version Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 44107
* mcs814x: remove linux 3.3 supportFelix Fietkau2015-01-2446-4103/+0
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 44106
* ar8216: prefix mii_xxx functions to avoid kernel namespace pollutionFelix Fietkau2015-01-243-18/+18
| | | | | | | | | Prefix the exported mii_xxx32 functions with ar8xxx_ to avoid kernel namespace pollution. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> SVN-Revision: 44105
* ar8216: add swconfig attribute to display ARL table on AR8327/AR8337Felix Fietkau2015-01-244-15/+220
| | | | | | | | | | | | | | Add global read-only swconfig attribute "arl_table" to display the address resolution table. So far the chip-specific part is implemented for AR8327/AR8337 only as I don't have the datasheets for the other AR8XXX chips. Successfully tested on TL-WDR4300 (AR8327rev2) and TL-WDR4900 (AR8327rev4). Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> SVN-Revision: 44104
* ar8216: decrease page switch wait timeFelix Fietkau2015-01-242-3/+9
| | | | | | | | | | | | | | | | | | | | | | Until a few years ago the page switch wait time was set to msleep(1) what was changed to usleep_range(1000, 2000) later. I can not imagine that a low-level operation like switching page on register level takes so much time. Most likely the value of 1ms was initially set to check whether it fixes an issue and then remained w/o further checking whether also a smaller value would be sufficient. Now the wait time is set to 5us and I successfully tested this on AR8327. IMHO 5us should be plenty of time for all supported chips. However I couldn't test this due to missing hardware. If other chips should need a longer wait time we can add the wait time as a parameter to the ar8xxx_chip struct. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> SVN-Revision: 44103
* ar8216: add link change detection for switch portsFelix Fietkau2015-01-242-0/+36
| | | | | | | | | | Check for switch port link changes and - flush ATU in case of a change - report link change via syslog Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> SVN-Revision: 44102
* ar8216: fix ATU flushingFelix Fietkau2015-01-242-9/+5
| | | | | | | | | | | | | | | | | | The functionality to flush the address translation table contains two bugs which luckily compensate each other. 1. Just setting the operation is not sufficient to perform the flushing. The "active" bit needs to be set to actually trigger an action. For the vtu operations this is implemented correctly. 2. ar8xxx_phy_read_status is called every 2s by the phy state machine to check for link changes. This would have caused an ATU flush every 2s. Fix the chip-specific ATU flush functions and remove the ATU flush call from ar8xxx_phy_read_status. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> SVN-Revision: 44101
* ar71xx: add support for TP-LINK TL-WR843ND v1John Crispin2015-01-233-0/+16
| | | | | | | | | TP-LINK TL-WR843ND v1 is the same model like wr41, but with Power over Ethernet on wan port. Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> SVN-Revision: 44085
* lantiq: correct value for fpi clock on ar9John Crispin2015-01-231-0/+21
| | | | | | | | | | | | | | | | | | | | | This adds a patch to target/linux/lantiq/patches-3.14 fixing a bug clock code on ar9. The current version returns the wrong value for the fpi clock frequency in some cases. See discussion for further details: https://lists.openwrt.org/pipermail/openwrt-devel/2015-January/030688.html I'm not sure about the patch naming and numbering convention. Do please let me know it this is not OK. Many thanks, Ben Mulvihill Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com> SVN-Revision: 44083
* ar71xx: add support for the UniFi AP Outdoor PlusJohn Crispin2015-01-226-3/+72
| | | | | | | | the GPIO controlling the rf filter is not configured properly by this patch. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> SVN-Revision: 44077
* ramips: add support for Tenda 3G150BJohn Crispin2015-01-228-1/+137
| | | | | | | | | | | | | | | Add suport for Tenda 3G150B: - cpu: Ralink RT5350F - flash: 4MB - ram: 32MB - 1x USB 2.0 - 1x RJ45 - one reset button - battery powered (BP-4L, 3.7V 1450mAh) Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> SVN-Revision: 44073
* ramips: improve and fix Memory 2 Move supportJohn Crispin2015-01-223-19/+13
| | | | | | | | | | | | | | | | | This patch is a follow up for my previous patch: "ramips: add support for Intenso Memory 2 Move USB 3.0". It fixes a couple of errors in the DTS (one of which broke the gpio-buttons). The kmod-leds-gpio dependency has been dropped as it is already part of the ramips target. Furthermore the ramdisk/uImage image is generated by default for the rt3050 subtarget. This image is needed to flash OpenWrt for the first time onto the device via TFTP. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> SVN-Revision: 44072
* mcs814x: document how to include 3rd party binary packagesFlorian Fainelli2015-01-211-2/+9
| | | | | | | | | | The dLAN USB Extender profile was referecing binary packages which are not to be included in any of the source-only feeds. Instead remove these references and document how to use the 3rd party feed. Signed-off-by: Florian Fainelli <florian@openwrt.org> SVN-Revision: 44071
* bcm53xx: backport official Buffalo WZR-900DHP patchRafał Miłecki2015-01-2117-45/+174
| | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 44070
* bcm53xx: backport spi-nor changes to add gd25q128 supportRafał Miłecki2015-01-212-0/+232
| | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 44069
* ar71xx: add support for TL-WA701ND v2John Crispin2015-01-209-1/+176
| | | | | | Signed-off-by: Luigi Tarenga <luigi.tarenga@gmail.com> SVN-Revision: 44063
* bcm53xx: use final (backported) patch fixing serial consoleRafał Miłecki2015-01-206-13/+25
| | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 44059
* bcm53xx: backport 3 BCM5301X patches from Hauke repoRafał Miłecki2015-01-2016-71/+537
| | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 44058
* bcm53xx: rename patches modifying DTS filesRafał Miłecki2015-01-206-60/+34
| | | | | | | | | Ths will allow us to use early 3xx numbers for patches designed for sending mainline. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 44057
* ralink: add support for firewrtJohn Crispin2015-01-206-1/+116
| | | | | | | | this is a mt7621 based board Signed-off-by: wengbj <linux.c@foxmail.com> SVN-Revision: 44055
* bcm53xx: add support/firmware for Asus RT-AC87URafał Miłecki2015-01-193-0/+157
| | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 44051
* ralink: fix ethernet rx buffer size breakageFelix Fietkau2015-01-181-2/+2
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 44047
* ralink: improve check rx sg function. use check frags instead of function callFelix Fietkau2015-01-183-14/+8
| | | | | | Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 44046
* ralink: correct handle hardware rx 2bytes offsetFelix Fietkau2015-01-183-13/+25
| | | | | | Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 44045
* ralink: use fe_reset to control all resetFelix Fietkau2015-01-188-41/+28
| | | | | | Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 44044
* ralink: improve tx_timeout functionFelix Fietkau2015-01-184-15/+87
| | | | | | | | | | * use default timeout value * print more debug ring info * move timeout reset function to workqueue Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 44043
* ralink: add ethernet fe and esw reset control bitFelix Fietkau2015-01-189-0/+44
| | | | | | Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 44042
* ralink: reduce access to uncached tx/rx dma ring bufferFelix Fietkau2015-01-184-53/+81
| | | | | | Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 44041
* sunxi: update Olimex A13 SOM profileZoltan Herpai2015-01-182-5/+5
| | | | | | Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu> SVN-Revision: 44040
* kirkwood: enable switch on Linksys EA3500Luka Perkov2015-01-183-2/+27
| | | | | | Signed-off-by: Claudio Leite <leitec@staticky.com> SVN-Revision: 44036
* kernel: add missing config symbol for 3.18Zoltan Herpai2015-01-181-0/+1
| | | | | | Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu> SVN-Revision: 44034
* lantiq: DGN3500 cleanupsJohn Crispin2015-01-182-3/+1
| | | | | | | | | This patch builds on the previous three to streamline support for the Netgear DGN3500. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> SVN-Revision: 44032
* lantiq: Restore call to orphaned etop functionJohn Crispin2015-01-181-16/+44
| | | | | | | | | It seems the call to ltq_get_eth_mac() disappeared at some point. This patch puts it where it currently most makes sense. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> SVN-Revision: 44031
* kernel: preserve bootloader command line on MIPSJohn Crispin2015-01-182-6/+38
| | | | | | | | | | | Somewhere in the conversion of the MIPS architecture code to Device Tree usage, there's been a failure to keep the separate variables holding the kernel command line reconciled between the tree and the bootloader. This patch restores previous functionality that broke. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> SVN-Revision: 44030
* lantiq: Fix initscript issueJohn Crispin2015-01-181-1/+1
| | | | | | | | | Currently this initscript fails if the macaddr has any leading zeroes. This patch corrects the problem. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> SVN-Revision: 44029
* ramips: downgrade mt7621 "Spurious GIC Interrupt" to debug messagesFelix Fietkau2015-01-181-1/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 44028
* ramips: add mt7621 cpu feature overridesFelix Fietkau2015-01-181-0/+68
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 44027
* kernel: add missing config symbolFelix Fietkau2015-01-182-0/+2
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 44026
* ramips: refresh kernel patchesFelix Fietkau2015-01-185-31/+31
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 44025
* kernel: backport upstream commit to fix MIPS cache shift with secondary ↵Felix Fietkau2015-01-184-5/+47
| | | | | | | | cache enabled Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 44024
* ar8216: display flow control info in swconfig get_link in case of ↵Felix Fietkau2015-01-182-1/+19
| | | | | | | | | | | | | | | | | | autonegatiation too The swconfig get_link attribute (at least) on AR8327/AR8337 doesn't consider the autonegotiated flow control. AR8327/AR8337 provide the info about autonegotiated rx/tx flow control in bits 10 and 11 of the port status register. Use these values to display info about autonegotiated rx/tx flow control as part of the get_link attribute. Successfully tested on TL-WDR4900 (AR8327 rev.4) and TL-WDR4300 (AR8327 rev.2). Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> SVN-Revision: 44023
* ar8216: add 802.3az EEE info to swconfig get_link attributeFelix Fietkau2015-01-185-1/+49
| | | | | | | | | | | | | AR8327/AR8337 allow to read the result of EEE autonegotiation. If EEE is autonegotiated between the link partners, display this as part of the swconfig get_link attribute. eee100: 100MBit EEE supported by both link partners eee1000: 1GBit EEE supported by both link partners Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> SVN-Revision: 44022
* ar8216: introduce enable_eee swconfig attribute to control 802.3az EEE per portFelix Fietkau2015-01-184-17/+122
| | | | | | | | | | | | | | | | Users reported network issues with AR8327 which turned out to be caused by EEE not working correctly with certain link partners (ticket 14597). The workaround was to disable EEE on all ports (changeset 41577). The issue was with certain link partners only, therefore this patch allows to control usage of EEE per port via swconfig. Still the default is to initially disable EEE on all ports. Successfully tested on a TL-WDR4900 (AR8327 rev.4) Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> SVN-Revision: 44021
* ramips: add missing copyright info for relocate stubFelix Fietkau2015-01-172-2/+8
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 44017
* ramips: add preliminary support for DIR-860L B1Felix Fietkau2015-01-176-3/+157
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 44016
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-11 01:11:12 +0000