aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: indicate upgrade using system LEDDavid Bauer2019-12-161-0/+3
| | | | | | | | | This enables the system LED to indicate a running firmware upgrade. This pattern is used on most platforms provided by the generic base-files package. ar71xx uses it's own implementation for the system-LED, where the upgrade case is not yet implemented. Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: add support for Enterasys WS-AP3710iDavid Bauer2019-12-137-0/+310
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: NXP P1020 (2x e500 @ 800MHz) RAM: 256M DDR3 (Micron) FLASH: 32M NOR (Spansion S29GL128S) BTN: 1x Reset WiFi: 1x Atheros AR9590 2.4 bgn 3x3 2x Atheros AR9590 5.0 an 3x3 ETH: 1x Gigabit Ethernet (Atheros AR8033) LED: System (green/red) - Radio{0,1} (green) LAN (connected to PHY) - GE blue - FE green Serial is a Cisco-compatible RJ45 next to the ethernet port. 115200-N-8 are the settings for OS and U-Boot. Installation ------------ 1. Grab the OpenWrt initramfs, rename it to 01C8A8C0.img. Place it in the root directory of a TFTP server and serve it at 192.168.200.200/24. 2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot by pressing Enter when prompted. Credentials are identical to the one in the APs interface. By default it is admin / new2day. 3. Set the bootcmd so the AP can boot OpenWrt by executing $ setenv boot_openwrt "setenv bootargs; cp.b 0xee000000 0x1000000 0x1000000; bootm 0x1000000" $ setenv bootcmd "run boot_openwrt" $ saveenv If you plan on going back to the vendor firmware - the bootcmd for it is stored in the boot_flash variable. 4. Load the initramfs image to RAM and boot by executing $ tftpboot 0x1000000 192.168.200.200:01C8A8C0.img; bootm 5. Make a backup of the "firmware" partition if you ever wish to go back to the vendor firmware. 6. Upload the OpenWrt sysupgrade image via SCP to the devices /tmp folder. 7. Flash OpenWrt using sysupgrade. $ sysupgrade -n /tmp/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for JCG JHR-AC876MDENG Qingfang2019-12-133-0/+162
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | JCG JHR-AC876M is an AC2600M router Hardware specs: SoC: MT7621AT 2.4GHz: MT7615N 4x4 @ PCIe0 5GHz: MT7615N 4x4 @ PCIe1 Flash: Winbond W25Q128JVSQ 16MiB RAM: Nanya NT5CB128M16 256MiB USB 2.0 and 3.0 ports 6 LEDs, 3 of which are connected to SoC GPIO Reset and WPS buttons Flash instructions: Stock to OpenWrt: Upload factory.bin in stock firmware's upgrade page, do not preserve settings OpenWrt to stock: Push and hold the reset button for 5s while power cycling to enter recovery mode; Visit 192.168.1.1 and upload stock firmware MAC addresses map: 0x0004 *:1c wlan2g/wan/label 0x8004 *:20 wlan5g 0xe000 *:1b lan 0xe006 *:1a not used in stock fw Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: allow JCG_MAXSIZE in kiB in Build/jcg-headerAdrian Schmutzler2019-12-132-2/+4
| | | | | | | | | | This allows JCG_MAXSIZE to be specified in kilobytes. This makes this value more consistent and easier comparable with other size variables. This also changes the only occurence of the variable, for Cudy WR1000. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for ipTIME A6ns-MSungbo Eo2019-12-133-0/+156
| | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A6ns-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A. Specifications: - SoC: MT7621AT - RAM: DDR3 128MB - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: MT7615 - 5GHz: MT7615 - Ethernet: 5x 10/100/1000Mbps - Switch: SoC internal - UART: - J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1 Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: DTS style improvements for mt7621_wevo_w2914ns-v2.dtsiAdrian Schmutzler2019-12-133-14/+7
| | | | | | | | | | | | This does several trivial DTS style improvements: - Move device name compatible to DTS files (and fix compatible in 11acnas.dts) - Remove xhci node as status is set to okay in mt7621.dtsi already - 0x0 instead of 0x0000 - Simplify state_default node definition Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for ZIO FREEZIOSungbo Eo2019-12-133-2/+33
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZIO FREEZIO is a 2.4/5GHz band AC1200 router, based on MediaTek MT7621A. Specifications: - SoC: MT7621AT - RAM: DDR3 128MB - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: MT7603EN - 5GHz: MT7612EN - Ethernet: 5x 10/100/1000Mbps - Switch: SoC internal - USB: 1x 3.0 - UART: - J4: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1 Notes: - FREEZIO has almost the same board as WeVO W2914NS v2. - Stock firmware is based on OpenWrt BB. MAC addresses in factory partition: 0x0004: WiFi 2.4GHz (label_mac-8) 0x002e: WAN (label_mac) 0x8004: WiFi 5GHz (label_mac-4) 0xe000: LAN (label_mac+1) Installation via web interface: 1. Access web admin page and turn on "OpenWrt UI mode". 2. Flash sysupgrade image through LuCI, with the "Keep settings" option OFF. Revert to stock firmware: 1. Perform sysupgrade with stock image. Make sure to NOT preserve settings. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [rebase, use mt7621_wevo_w2914ns-v2.dtsi] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* sunxi: add support for FriendlyARM Nano PI NEO Air dev boardRoman Bazalevsky2019-12-131-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware: Allwinner H3 upto 1.2GHz 512MB DDR3 RAM 8GB on-board eMMC - mountable, can be used as boot with custom boot.scr microSD-card slot WiFi 802.11n (AP6212A) - working Bluetooth (AP6212A) - not working for now Micro-USB OTG + 2*USB headers UART 3.3V - working GPIO/I2C/SPI 2.54mm headers Standard sunxi SD-card installation procedure - copy image to SD card, insert in into slot and boot. First time you will need UART adapter to enable on-board wireless (or just build custom image with enabled WiFi). To boot from eMMC: - boot from SD - copy SD image to emmc (dd bs=... if=.... of=/dev/mmcblk2) - mount eMMC boot partition and replace boot script on it - unmount, reboot To use i2c, spi and more uarts - replace dtb on boot partition with fixed one (use dtc or fdt-tools). Signed-off-by: Roman Bazalevsky <rvb@rvb.name> [rebase onto device name consolidation patches] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* sunxi: construct DTS name from device node name and SOCAdrian Schmutzler2019-12-134-35/+45
| | | | | | | | | The device part in the SUNXI_DTS variable always corresponds to device node name. This is another redundancy that can be removed by calculating the DTS name from a newly introduced SUNXI_SOC variable and the node name. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* sunxi: use vendor_device scheme for device definitionsAdrian Schmutzler2019-12-134-99/+69
| | | | | | | | | | | | This changes device definition to resemble the vendor_device scheme already present for the majority of device compatible strings. By doing this, we achieve several advantages at once: - Image names and node names are more consistent with other targets. - SUPPORTED_DEVICES can be set automatically for all but two cases. - Image names and node names are in line with DEVICE_TITLEs. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link TL-WDR4300 v1 (IL)Adrian Schmutzler2019-12-124-1/+23
| | | | | | | | The TL-WDR4300 v1 sold in Israel has a different TPLINK_HWID. Thanks to Josh4300 for testing on device. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: redistribute UBNT variables in Ubiquiti image MakefileAdrian Schmutzler2019-12-121-15/+18
| | | | | | | | | | | | | The variables UBNT_BOARD and UBNT_VERSION are defined in the parent Device/ubnt definition and then overwritten for most of the derived platform definitions (e.g. Device/ubnt-wa). Since this mixed use of inheritance and overwriting can be misleading, this moves the variables to the platform-based definitions. While at it, reorder the definitions to have order consistent, too. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add label MAC address for Mikrotik RBM33GAdrian Schmutzler2019-12-121-1/+4
| | | | | | | | | | | | | | The device label contains: E01: B8:69:F4:xx:xx:07 E02: B8:69:F4:xx:xx:09 The first value corresponds to the address set in hard_config 0x10. That one is taken for the label MAC address. Thanks to Martin Schiller for retrieving the information. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: rt305x: use flash location for wan_mac in 02_networkAdrian Schmutzler2019-12-125-50/+60
| | | | | | | | | | | | | | | | | | | | | | | | | This uses the flash locations instead of eth0 MAC address to calculate MAC address increments for WAN. The change will make the MAC address setup of a particular device more obvious and removes the dependency of 02_network on the eth0 initialization. This removes the wan_mac setup for the following devices as they do not set up a MAC address for ethernet in the first place: - asiarf,awapn2403 - belkin,f7c027 - dlink,dir-615-d - mofinetwork,mofi3500-3gn - prolink,pwh2004 - ralink,v22rw-2x2 - unbranded,wr512-3gn-4m - unbranded,wr512-3gn-8m While at it, make some DT node labels consistent with the label property. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: rt288x: use flash location for wan_mac in 02_networkAdrian Schmutzler2019-12-121-4/+5
| | | | | | | | | | | | | | This uses the flash locations instead of eth0 MAC address to calculate MAC address increments for WAN. The change will make the MAC address setup of a particular device more obvious and removes the dependency of 02_network on the eth0 initialization. This removes the wan_mac setup for ralink,v11st-fe as this device does not set up a MAC address for ethernet in the first place. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt76x8: use flash location for wan_mac in 02_networkAdrian Schmutzler2019-12-122-19/+29
| | | | | | | | | | | | | | This uses the flash locations instead of eth0 MAC address to calculate MAC address increments for WAN. The change will make the MAC address setup of a particular device more obvious and removes the dependency of 02_network on the eth0 initialization. While at it, change the partition label for zyxel,keenetic-extra-ii to factory to be consistent with node label and all the other devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: use flash location for wan_mac in 02_networkAdrian Schmutzler2019-12-121-16/+26
| | | | | | | | | | | This uses the flash locations instead of eth0 MAC address to calculate MAC address increments for WAN. The change will make the MAC address setup of a particular device more obvious and removes the dependency of 02_network on the eth0 initialization. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7620: use flash location for wan_mac in 02_networkAdrian Schmutzler2019-12-121-12/+16
| | | | | | | | | | | This uses the flash locations instead of eth0 MAC address to calculate MAC address increments for WAN. The change will make the MAC address setup of a particular device more obvious and removes the dependency of 02_network on the eth0 initialization. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove wan_mac setup for evaluation boardsAdrian Schmutzler2019-12-123-6/+0
| | | | | | | | The evaluation boards do not set up a MAC address for eth0 in the first place, so it does not make sense to calculate a WAN address from the random MAC used there. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: create common DTSI for TP-Link Archer C20i/C20 v1/C50 v1Adrian Schmutzler2019-12-124-358/+137
| | | | | | | The TP-Link Archer C20i/C20 v1/C50 v1 seem to be almost the same, so creating a common DTSI will reduce duplicate code. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove unused DTS variable from DEVICE_VARSAdrian Schmutzler2019-12-121-1/+1
| | | | | | | | | | | | | The DTS variable has been removed in 402138d12dca ("ramips: Derive DTS name from device name in Makefile"), but the DEVICE_VARS entry has been overlooked. Remove it now since we are not using this variable. This must _not_ be backported to 19.07, where the variable is still in use. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix switch port numbering for RT-AC65P/RT-AC85PGabor Varga2019-12-111-2/+2
| | | | | | | | | | | The switch LAN port numbers are in reversed order with original config. With this patch they are fixed. Port order checked on both devices. Signed-off-by: Gabor Varga <vargagab@gmail.com> [merged definitions into appropriate block, extended commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add label MAC address for TP-Link Archer C20iAdrian Schmutzler2019-12-111-0/+4
| | | | | | | | | | | | | | Current OpenWrt MAC setup: eth0 &rom 0xf100 :48 eth0.2 eth0+1 :49 wlan0 (5 GHz) &radio 0x8004 different OUI wlan1 (2.4 GHz) &radio 0x4 same OUI as wlan0 Label MAC address corresponds to eth0 (&ethernet). No additional addresses found in hexdump of rom/radio. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: fix typos in DTSDENG Qingfang2019-12-114-11/+11
| | | | | | Replace "usb_ochi" with "usb_ohci", and "usb_echi" with "usb_ehci". Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* kernel: bump 4.19 to 4.19.88Koen Vandeputte2019-12-1025-356/+55
| | | | | | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 0004-boot-sq201-from-sda1.patch - 500-v4.20-ubifs-Fix-default-compression-selection-in-ubifs.patch - 0003-usb-dwc2-use-a-longer-core-rest-timeout-in-dwc2_core.patch Altered patches: - 0011-ARM-dts-Fix-up-SQ201-flash-access.patch - 400-mtd-add-rootfs-split-support.patch - 0101-pci-mediatek-backport-fix-pcie.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.158Koen Vandeputte2019-12-1020-40/+40
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 400-mtd-add-rootfs-split-support.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.206Koen Vandeputte2019-12-1016-45/+45
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 400-mtd-add-rootfs-split-support.patch Compile-tested on: none Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* malta: remove CONFIG_LEGACY_PTY from kernel configDaniel Golle2019-12-092-4/+0
| | | | | | Having legacy PTYs enabled causes problems with procd-hotplug. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* sunxi: remove CONFIG_LEGACY_PTY from kernel configDaniel Golle2019-12-092-4/+0
| | | | | | Having legacy PTYs enabled causes problems with procd-hotplug. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* layerscape: remove CONFIG_LEGACY_PTY from kernel configDaniel Golle2019-12-092-4/+0
| | | | | | Having legacy PTYs enabled causes problems with procd-hotplug. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kirkwood: remove CONFIG_LEGACY_PTY from kernel configDaniel Golle2019-12-092-4/+0
| | | | | | Having legacy PTYs enabled causes problems with procd-hotplug. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* at91: disable legacy PTYs and virtual terminalsDaniel Golle2019-12-091-6/+0
| | | | | | | | | Enabling legacy PTYs causes problems with procd-hotplug. And as this is a headless target, no need to have virtual terminals. Remove corresponding kernel config options, they are disabled in generic kernel config. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mpc85xx: remove CONFIG_LEGACY_PTY from kernel configDaniel Golle2019-12-092-4/+0
| | | | | | Having legacy PTYs enabled causes problems with procd-hotplug. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ixp4xx: remove CONFIG_LEGACY_PTY from kernel configDaniel Golle2019-12-091-2/+0
| | | | | | Having legacy PTYs enabled causes problems with procd-hotplug. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uml: remove CONFIG_LEGACY_PTY from kernel configDaniel Golle2019-12-092-4/+0
| | | | | | Having legacy PTYs enabled causes problems with procd-hotplug. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: disable legacy PTYs and virtual terminalsDaniel Golle2019-12-091-6/+0
| | | | | | | | | Enabling legacy PTYs causes problems with procd-hotplug. And as this is a headless target, no need to have virtual terminals. Remove corresponding kernel config options, they are disabled in generic kernel config. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* treewide: remove dts-v1 identifier from DTSI filesAdrian Schmutzler2019-12-0846-49/+0
| | | | | | | | | | | | | | | | The "/dts-v1/;" identifier is supposed to be put once at the beginning of a device tree file. Thus, it makes no sense to provide it a second time in to-be-included DTSI files. This removes the identifier from all DTSI files in /target/linux. Most of the DTS files in OpenWrt do contain the "/dts-v1/;". It is missing for most of the following targets, though: mvebu, ipq806x, mpc85xx, ipq40xx This does not touch ipq806x for now, as the bump to 4.19 is close. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* brcm47xx: add switch configuration for WNR3500LOlli Asikainen2019-12-081-1/+2
| | | | | | | | | | | | | | | | | | | | Netgear WNR3500L is an already supported device, but out of the box, the device has no switch configuration and there is no wan. The correct configuration for this specific model is similar to some other models. This simple commit adds the correct switch and the out-of-the-box experience is improved. Experimentally determined: Port 0 => WAN Port 1..4 => LAN Port 5..7 => unused Port 8 => CPU Signed-off-by: Olli Asikainen <olli.asikainen@gmail.com> Tested-by: Fabian Zaremba <fabian@youremail.eu> [added port mapping to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: convert mediatek,mtd-eeprom from decimal to hex notationAdrian Schmutzler2019-12-083-6/+6
| | | | | | | | | | A small subset of devices uses decimal notation for mediatek,mtd-eeprom in DTS files. Convert to hexadecimal notation to be consistent with all the rest. Also change "0" to "0x0" in the same files for consistency. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix number of LAN Ports for Mikrotik RBM33GMartin Schiller2019-12-081-1/+4
| | | | | | | | The Mikrotik RBM33G has only 2 LAN ports. Signed-off-by: Martin Schiller <ms@dev.tdt.de> [moved node in 02_network to maintain alphabetic sorting] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix switch port order for TP-Link Archer C20iWalter Sonius2019-12-081-1/+1
| | | | | | | | | | | | | | | | | | Physical port order watched from the backside of the C20i (from left to right) is: Internet / 1 / 2 / 3 / 4 Physical Port Switch port WAN 0 LAN 3 1 LAN 4 2 LAN 1 3 LAN 2 4 (not used) 5 CPU 6 Signed-off-by: Walter Sonius <walterav1984@gmail.com> [commit message/title improvements] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: fix WNDR3700/WNDR3800 wifi reg sizeChristian Lamparter2019-12-071-2/+2
| | | | | | | | "[...] the size component shall be zero." (See "PCI Bus Binding to: IEEE Std 1275-1994 Rev 2.1" section "4.1.1 Open Firmware-defined Properties for Child Nodes") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mediatek: fix pcie bringup issueJohn Crispin2019-12-051-0/+9
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ath79: add support for Ubiquiti LiteBeam AC Gen2Stijn Tintel2019-12-044-0/+52
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware: * SoC: Atheros AR9342-BL1A * RAM: 64MB DDR2 (Winbond W9751G6KB-25) * Flash: 16MB SPI NOR (Macronix MX25L12835FZ2I-10G) * Ethernet: 1x 10/100/1000 Mbps (Atheros AR8035-A) with 24V PoE support * Wifi 2.4GHz: Atheros AR9340 v2 * WiFi 5GHz: Ubiquiti U-AME-G1-BR4A (rebranded QCA988X v2) * LEDs: 1x Power, 1x Ethernet * Buttons: 1x Reset * UART: 1x TTL 115200n8, 3.3V RX TX GND, 3.3V pin closest to RJ45 port The LEDs do not seem to be connected to any GPIO, so there is currently no way to control them. Installation via U-Boot, TFTP and serial console: * Configure your TFTP server with IP 192.168.1.254 * Connect serial console and power up the device * Hit any key to stop autoboot * tftpboot 0x81000000 openwrt-ath79-generic-ubnt_litebeam-ac-gen2-initramfs-kernel.bin * bootm 0x81000000 * copy openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin to /tmp * sysupgrade /tmp/openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Petr Štetiar <ynezz@true.cz> Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: drop IMAGE/factory.bin from ubnt-wa devicesStijn Tintel2019-12-041-4/+0
| | | | | | | | | | The sysupgrade image contains OpenWrt specific metadata. Having this metadata in the factory images makes no sense. Drop IMAGE/factory.bin from Device/ubnt-wa and use the default from Device/ubnt instead. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Petr Štetiar <ynezz@true.cz> Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: act_ctinfo: fix updated backport on 4.14Kevin Darbyshire-Bryant2019-12-041-21/+8
| | | | | | | | It turns out my 4.14 testing had a rather large flaw in it and the 'extack' mechanism isn't quite ready. Remove the extack stuff from this backport. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kernel: act_ctinfo: update backportKevin Darbyshire-Bryant2019-12-032-72/+210
| | | | | | | | | | Since the original backports from kernel 5.3 a few things have been tweaked by kernel bumps & other upstream changes. Update the backport to reflect upstream as closely as possible and remove the bitrot. Functions remain the same, error reporting improved. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ath79: fix source of label MAC address for Ubiquiti XM devicesAdrian Schmutzler2019-12-031-6/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In d421a8b94489 ("ath79: read label MAC address from flash instead of using phy0/phy1") the source of the label MAC address was changed for devices just reading it from phy0. To get rid of the dependency from phy startup, addresses were read directly from the flash locations that are used to initialize the phy MAC addresses. Unfortunately, it turned out that Ubiquiti XM devices seem to have different flash locations than expected, and also seem to have specific locations for different devices (all in art/EEPROM): 0xe012 AR9280 Nanostation M2 - 0x120c 0xe035 AR9280 Nanostation M3 - 0x120c 0xe1b2 AR9280 Rocket M2 - 0x120c 0xe1c3 AR9280 Rocket M3 - 0x120c 0xe1b5 AR9280 Rocket M5 - 0x120c 0xe2d5 AR9280 Bullet M2 Titanium - 0x120c 0xe2b5 AR9280 Nanobridge M5 - 0x120c 0xe202 AR9280 Bullet M2 - 0x120c 0xe232 AR9287 Nanobridge M2 - 0x110c 0xe4a2 AR9285 AirRouter - 0xa0bf Picostation M2 - 0x120c and 0xa0bf Nanostation Loco M2 - not in 0x120c, other locations not checked An additional problem of the Ubiquiti device support in OpenWrt is that we provide images that match several subvariants of the devices, which might have different MAC address locations. Given that reading the address from phy0 in 02_network _is_ working for the ath79 target in general, it does not seem reasonable to rebuild a complex MAC address retrieval mechanism which is already present in the ath9k driver. So, this patch reverts the label MAC address source for Ubiquiti XM devices (and the Unifi AP) to /sys/class/ieee80211/phy0/macaddress. This doesn't affect XW and Unifi AC devices, where the label MAC address source is defined via device tree. For alfa-network,ap121f the location 0x1002 is kept, as this has been verified during device support preparation in PR #2199. Fixes: d421a8b94489 ("ath79: read label MAC address from flash instead of using phy0/phy1") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* octeon: fix sysupgradeStijn Tintel2019-11-301-2/+2
| | | | | | | | Sysupgrade was failing due to incorrect replacement of backticks: /sbin/sysupgrade: /lib/upgrade/platform.sh: line 101: syntax error: missing '))' Fixes: 0bbfc3dff719 ("octeon: replace backticks by $(...)") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* generic ar8xxx: increase VLAN table for AR83x7David Bauer2019-11-303-9/+13
| | | | | | | | | | | | The Atheros AR8327 and AR8337 have (according to their datasheet) a VLAN table with a maximum of 4096 entries. Currently, there's a hard limit of 128 VLANs, which is the same as for most other Atheros switches. Increase this limit only for the AR83x7 series and modify some shared functions to allow them to work with a variable max VLAN count. Signed-off-by: David Bauer <mail@david-bauer.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-27 21:14:33 +0000