aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
...
* ramips: fix some clocks in mt7621.dtsiWeijie Gao2018-11-261-11/+2
| | | | | | | As the cpu clock calculation has been fixed, the clock for gic and spi should be also fixed. Signed-off-by: Weijie Gao <hackpascal@gmail.com>
* ramips: fix cpu clock of mt7621 and add dt clk devicesWeijie Gao2018-11-263-19/+232
| | | | | | | | | | For a long time the mt7621 uses a fixed cpu clock which causes a problem if the cpu frequency is not 880MHz. This patch fixes the cpu clock calculation and adds the cpu/bus clkdev which will be used in dts. Signed-off-by: Weijie Gao <hackpascal@gmail.com>
* ramips: fix register range of memc node in mt7621.dtsiWeijie Gao2018-11-261-1/+1
| | | | | | | The memc node from mt7621.dtsi has incorrect register resource. Fix it according to the programming guide. Signed-off-by: Weijie Gao <hackpascal@gmail.com>
* ramips: merge two patches 101-mt7621-timer and 998-mt7621-needs-jiffiesWeijie Gao2018-11-262-10/+8
| | | | | | | | These two patches both modified the mt7621.c, and the patch file 998-mt7621-needs-jiffies.patch adds only one line which is used by the another patch file. So merge them into one file. Signed-off-by: Weijie Gao <hackpascal@gmail.com>
* ath79: specify "firmware" partition format for Buffalo devicesINAGAKI Hiroshi2018-11-264-0/+4
| | | | | | | | | | | | | | Specify firmware partition format (denx,uimage) by compatible string for Buffalo devices. affected devices (&run tested): - BHR-4GRV - WHR-G301N - WZR-HP-AG300H - WZR-HP-G302H A1A0 - WZR-HP-G450H (WZR-450HP) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* sdk: expose part of advanced configuration optionsTomasz Maciej Nowak2018-11-261-0/+57
| | | | | | | | These option can be useful in developement/packagig applications for OpenWrt. Instead of searching them by hand in Config-build.in lets expose them for easier access. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ramips: add mt76x0 node to RT-AC51U device treeLorenzo Bianconi2018-11-261-0/+11
| | | | | | | Introduce mt76x0e device tree node in RT-AC51U dts. Define mt76x0e mtd partition and offset Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
* apm821xx: wndr4700: restore sd-card media detectionChristian Lamparter2018-11-261-1/+1
| | | | | | | This was not converted to the new, dt-based board name. Fixes: e90dc8d2722 ("apm821xx: convert to device-tree board detection") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: shuffle helper scripts to the frontChristian Lamparter2018-11-261-83/+82
| | | | | | | In a patch for the ath79, Mathias Kresin mentioned that helper scripts should be in front of the device targets. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: add support for the Netgear WNDAP620 and WNDAP660Christian Lamparter2018-11-269-1/+370
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear WNDAP620 and WNDAP660, they are similar devices, but due to the LAN LED configuration, the switch setup and WIFI configuration each gets a different device target. Hardware Highlights WNDAP620: CPU: AMCC PowerPC APM82181 at 1000 MHz DRAM: 128 MB, 2 x 64 MiB DDR2 Hynix H5PS5162GF CPU: AMCC PowerPC APM82181 at 1000 MHz FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY - Only 1 GBit Port (POE) Wifi: Atheros AR9380 minipcie - Dual-Band - 3x3:3 Serial: console port with RJ45 Interface (9600-N-8-1) LEDS: Power, LAN-Activity, dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs Button: Soft Reset Button Antennae: 3 internal dual-band antennae + 3 x RSMA for external antennaes Hardware Highlights WNDAP660: CPU: AMCC PowerPC APM82181 at 1000 MHz + 2 Heatsinks DRAM: 256 MB, 2 x 128 MiB DDR2 FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY (POE) Wifi1: Atheros AR9380 minipcie - Dual-Band - 3x3:3 Wifi2: Atheros AR9380 minipcie - Dual-Band - 3x3:3 Serial: console port with RJ45 Interface (9600-N-8-1) LEDS: Power, LAN-Activity, 2x dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs Button: Soft Reset Button Antennae: 6 internal dual-band antennae + 3 x RSMA for external antennaes Flashing requirements: - needs a tftp server at 192.168.1.10/serverip. - special 8P8C(aka RJ45)<->D-SUB9 Console Cable ("Cisco Console Cable"). Note: Both WNDAP6x0 have a MAX3232 transceivers, hence no need for any separate CMOS/TTL level shifters. External Antenna: The antennae mux is controlled by GPIO 11 and GPIO14. Valid Configurations: = Config# = | = GPIO 11 = | = GPIO 14 = | ===== Description ===== 1. | 1 / High | 0 / Low | Use the internal antennae (default) 2. | 0 / Low | 1 / High | Use the external antennae The external antennaes are only meant for the 2.4 GHz band. One-way Flashing instructions via u-boot: 0. connect the serial cable to the RJ45 Console Port Note: This requires a poper RS232 and not a TTL/USB adaptor. 1. power up the AP and interrupt the u-boot process at 'Hit any key to stop autoboot' 2. setup serverip and ipaddr env settings Enter the following commands into the u-boot shell # setenv ipaddr 192.168.1.1 # setenv serverip 192.168.1.10 3. download the factory.img image to the AP Enter the following commands into the u-boot shell # tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-squashfs-factory.img 4. verfiy image integrity Enter the following commands into the u-boot shell # crc32 $fileaddr $filesize If the calculated crc32 checksum does not match, go back to step 3. 5. flash the image Enter the following commands into the u-boot shell # nand erase 0x110000 0x1bd0000 # nand write ${kernel_addr_r} 0x110000 ${filesize} 6. setup uboot environment Enter the following commands into the u-boot shell # setenv bootargs # setenv fileaddr # setenv filesize # setenv addroot 'setenv bootargs ${bootargs} root=/dev/ubiblock0_0' # setenv owrt_boot 'nboot ${kernel_addr_r} nand0 0x110000; run addroot; run addtty; bootm ${kernel_addr_r}' # setenv bootcmd 'run owrt_boot' # saveenv 7. boot # run bootcmd Booting initramfs instructions via u-boot: Follow steps 0 - 2 from above. 3. boot initramfs Enter the following commands into the u-boot shell # tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-initramfs-kernel.bin # run addtty # bootm ${kernel_addr_r} Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* generic: rtl8367b: make it possible to specify cpu_port via DTChristian Lamparter2018-11-261-2/+4
| | | | | | | | This patch adds the feature to parse the existing cpu_port DT property, which is used to specify which port is the cpu port of the switch. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* generic: rtl836x: support defered probe on mdio-busChristian Lamparter2018-11-265-13/+17
| | | | | | | | | | | | | | | | On the WNDAP620, the mdio and mdc lines are controlled by the EMAC ethernet device. This results in a hen-vs-egg problem. The rtl8367b driver is probed before the ethernet driver and the mdio-bus is not available yet, which caused the rtl8367b driver to fail. This patch changes the rtl8366_smi_probe_of() function to return -EPROBE_DEFER if the mdio-bus lookup failed and changes rtl8366_smi_probe()'s signature to return the error code back to the callee, so it can propagate back to the kernel. Which, will retry the switch probe at a later time. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: import gpio-export DT code from lantiqChristian Lamparter2018-11-261-0/+169
| | | | | | This will come in handy for the Netgear WNDAP620's antennae mux. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: MR24: add to uboot-envtoolsChristian Lamparter2018-11-261-1/+24
| | | | | | | | This patch adds the complicated u-boot environment access settings for to the MR24 target. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq806x: Add support for IPQ8064 AP161 boardRam Chandra Jangir2018-11-265-1/+295
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: Qualcomm Atheros IPQ8064 ARM-v7 Dual Core SMP CPU - RAM: 512MB DDR3 System Memory - NOR Flash: 32MB SPI NOR - NAND Flash: 256MB NAND - Ethernet: 5 x 1G via QCA8337N - USB: 2 x USB 3.0 SuperSpeed - PCIe: 3x Mini PCIe 2.0 Slots Three PCIE2.0 connectors can connect two or three radio cards such as the CUS260 for 2.4 GHz WLAN and the CUS239 for 802.11ac WLAN How to flash via u-boot console: tftpboot 0x44000000 openwrt-ipq806x-qcom_ipq8064-ap161-squashfs-nand-factory.bin nand erase 0x1340000 0x4000000 nand write 0x44000000 0x1340000 $filesize setenv bootargs ‘console=ttyMSM0,115200 ubi.mtd=ubi root=/dev/ubiblock0_1’ saveenv bootm Further upgrades via sysupgrade. Tested on IPQ8064 AP161 Board: 1) NAND boot 2) Tested USB and PCIe interfaces 3) WDOG test 4) cpu frequency scaling 5) ethernet, 2G and 5G WiFi 6) ubi sysupgrade Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
* ipq8064: pinctrl: Fixed missing RGMII pincontrol definitionsRam Chandra Jangir2018-11-261-0/+54
| | | | Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
* ar71xx: fix RouterBOARD Power LED default stateSergey Ryazanov2018-11-262-2/+2
| | | | | | | | | | | | | | RouterBOARD(s) bootloader actully turns Power LED off just before it starts the kernel. So we need to set the LED default status to On instead of Keep in order to keep LED on during kernel boot. This change fixes Power LED off during the kernel boot on the RB91x and SXT Lite boards. Fixes: 6cad8ee0bd ("ar71xx: keep the RouterBOARD Power LED in On state") CC: Mathias Kresin <dev@kresin.me> Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* hotplug: Allow configuring radio name.Ben Greear2018-11-261-0/+21
| | | | | | | | | | | | | This way the radio (phy) name can be the same through module reloads. To set the desired name: uci set wireless.@wifi-device[0].phyname=wiphy0 I guess this only works on ipq6086 boards as I could not find a more generic place to put this. Maybe someone can improve it. Signed-off-by: Ben Greear <greearb@candelatech.com>
* x86: add amd microcode entries to grub configTomasz Maciej Nowak2018-11-263-16/+14
| | | | | | | | Create initrd enries for x86 images, that'll load amd microcode as early as possible. Also remove the preinit script responsible for late load of microcode. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: add support for Archer C58/C59 v1David Bauer2018-11-269-1/+441
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Archer C58 v1 and C59 v1, previously supported in the ar71xx target. CPU: Qualcomm QCA9561 RAM: 64M (C58) / 128M (C59) FLASH: 8M (C58) / 16M (C59) WiFi: QCA9561 bgn 3x3:3 QCA9888 nac 2x2:2 LED: Power, WiFi 2.4, WiFi 5, WAN green, WAN amber, LAN, WPS Only C59: USB BTN: WPS, WiFi, Reset Installation ------------ Via Web-UI: Update factory image via Web-UI. Via TFTP: Rename factory image to "tp_recovery.bin" and place it in the root-dir of your tftp server. Configure to listen on 192.168.0.66. Power up the router while holding down the reset-button. The router will flash itself and reboot. Note: For TFTP, you might need a switch between router and computer, as link establishment might take to long. Signed-off-by: David Bauer <mail@david-bauer.net>
* ralink: Add support for GPIO as interrupt-controllerDaniel Santos2018-11-261-0/+51
| | | | | | | | | The gpio-ralink driver has everything it needs to be used as an interrupt controller except for device tree support. This simple patch adds that support by configuring the irq domain to use two cells and adding the appropriate documentation to the devicetree bindings. Signed-off-by: Daniel Santos <daniel.santos@pobox.com>
* ath79: add support for GL-iNet GL-X750Luo chongjun2018-11-266-2/+159
| | | | | | | | | | | | | | | | | | | this patch adds supports for GL-X750. Specification: - SOC: QCA9531 (650MHz) - Flash: 16 MiB (W25Q128FVSG) - RAM: 128 MiB DDR2 - Ethernet: 10/100: 1xLAN + 10/100: 1xWAN - Wireless: 2.4GHz (bgn) and 5GHz (ac) - USB: 1x USB 2.0 port - Button: 1x reset button - LED: 5x LEDS (green) Flash instruction: The original firmware is openwrt, so both LuCI or sysupgrade can be used. Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
* ar71xx: add support for UniFi-AC-Mesh-ProChristoph Krapp2018-11-265-8/+21
| | | | | | | | | | | | | | | | This adds the build option for UniFi AC Mesh Pro as well as model detection for it. The device is a hardware clone of the AC Pro. - SoC: QCA9563-AL3A (775Mhz) - RAM: 128MiB - Flash: 16MiB - dual firmware partitions! - LAN: 2x 1000M - POE+ - Wireless: 2.4G: QCA9563 5G: UniFi Chip, QCA988X compatible Signed-off-by: Christoph Krapp <achterin@googlemail.com>
* ramips: Add support for ZTE ZXECS EBG3130 aka BDCOM WAP2100-SKPetr Štetiar2018-11-266-1/+149
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On the bottom sticker it's branded as ZTE ZXECS EBG3130 device, but in factory OpenWrt image it's referenced as BDCOM WAP2100-SK device. Specifications: - SoC: MediaTek MT7620A - RAM: 128 MB - Flash: 16 MB - Ethernet: 5 FE ports - Wireless radio: 2T2R 2.4 GHz and 1T1R 5 GHz (MT7610EN, unsupported) - UART: 1 x UART on PCB marked as J2 (R=RX, T=TX, G=GND) with 115200 8N1 config - LEDs: Power, FE ports 1-5, WPS, USB, RF 2.4G, RF 5G - Other: USB port, SD card slot and 2x external antennas (non-detachable) Flashing instructions: A) The U-Boot has HTTP based firmware upgrade A1) Flashing notes We've identified so far two different batches of units, unfortunately each batch has different U-Boot bootloader flashed with different default environment variables, thus each batch has different IP address for accessing web based firmware updater. * First batch has web based bootloader IP address 1.1.1.1 * Second batch has web based bootloader IP address 192.168.1.250 In case you can't connect to either of those IPs, you can try to get the default IP address via two methods: A1.1) Serial console, then the IP address is visible during the boot ... HTTP server is starting at IP: 1.1.1.1 raspi_read: from:40004 len:6 HTTP server is ready! ... A1.2) Over telnet/SSH using this command: root@bdcom:/# grep ipaddr= /dev/mtd0 ipaddr=1.1.1.1 A2) Flashing with browser * Change IP address of PC to 1.1.1.2 with 255.255.255.0 netmask * Reboot the device and try to reach web based bootloader in the browser with the following URL http://1.1.1.1 * Quickly select the firmware sysupgrade file and click on the `Update firmware` button, this all has to be done within 10 seconds, bootloader doesn't wait any longer If done correctly, the web page should show UPDATE IN PROGRESS page with progress indicator. Once the flashing completes (it takes roughly around 1 minute), the device will reboot to the OpenWrt firmware A3) Flashing with curl sudo ip addr add 1.1.1.2/24 dev eth0 curl \ --verbose \ --retry 3 \ --retry-delay 1 \ --retry-max-time 30 \ --connect-timeout 30 \ --form "firmware=@openwrt-ramips-mt7620-BDCOM-WAP2100-SK-squashfs-sysupgrade.bin" \ http://1.1.1.1 Now power on the router. B) The U-boot is based on Ralink SDK so we can flash the firmware using UART. 1. Configure PC with a static IP address and setup an TFTP server. 2. Put the firmware into the tftp directory. 3. Connect the UART line as described on the PCB (G=GND, R=RX, T=TX) 4. Power up the device and press 2, follow the instruction to set device and tftp server IP address and input the firmware file name. U-boot will then load the firmware and write it into the flash. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* x86: add intel microcode entries to grub configTomasz Maciej Nowak2018-11-264-4/+12
| | | | | | | | | Create initrd enries for x86 images, that'll load intel microcode as early as possible. To achieve that the test module for grub is enabled which provides shell-like conditionals. Also restrict the late load of microcode to AMD processors. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* x86: add packages files to image bootfsTomasz Maciej Nowak2018-11-261-0/+2
| | | | | | | Add files to bootfs image from selected as built-in packages, which want to install files to targets boot file system. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* x86: mount writable bootfsTomasz Maciej Nowak2018-11-261-8/+4
| | | | | | | Mount boot file system with rw option to allow installation of packages which install files to /boot directory. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: ubnt-m-xw: Fix factory image flashing using TFTP recovery methodPetr Štetiar2018-11-261-2/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ubiquity allows flashing of unsigned factory images via TFTP recovery method[1]. They claim in airOS v6.0.7 release changelog[2] following: All future airOS versions will be signed in this way and not allow unsigned firmware to be loaded except via TFTP. U-boot bootloader on M-XW devices expects factory image revision version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039 (May 24 2017 - 15:58:18)` bootloader checks if the revision major(?) number is actually a number, but in currently generated images there's OpenWrt text and so the check fails: Hit any key to stop autoboot: 0 Setting default IP 192.168.1.20 Starting TFTP server... Receiving file from 192.168.1.25:38438 Received 4981148 bytes Firmware check failed! (1) By placing arbitrary correct number first in major version, we make the bootloader happy and we can flash factory images over TFTP again: Received 3735964 bytes Firmware Version: XW.ar934x.v6.0.4-42.r8474-56aa1ac-OpenWrt Setting U-Boot environment variables Un-Protected 1 sectors Erasing Flash.... done Patch provided by AREDN[3] project, tested on Bullet M2 XW (ynezz) and Nanostation M5 XW (ae6xe). 1. https://help.ubnt.com/hc/en-us/articles/204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points 2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt 3. https://github.com/aredn Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: Add support for Ubiquity Bullet M (XW)Petr Štetiar2018-11-265-0/+171
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CPU: AR9342 SoC RAM: 64 MB DDR2 Flash: 8 MB NOR SPI Ports: 100 MBit (24V PoE in) WLAN: 2.4/5 GHz UART: 1 UART on PCB marked as J1 with 115200 8N1 config LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green) Buttons: Reset UART connection details .---------------------------------. | | [ETH] J1 [ANT] | o VCC o RX o TX o GND | `---------------------------------' Flashing instructions A) Serial console, U-Boot and TFTP 1. Connect to serial header J1 on the PCB 2. Power on device and enter U-Boot console 3. Set up TFTP server serving an OpenWrt initramfs build 4. Load initramfs build using the command tftpboot in the U-Boot cli 5. Boot the loaded image using the command bootm 6. Copy squashfs OpenWrt sysupgrade build to the booted device 7. Use mtd to write sysupgrade to partition "firmware" 8. Reboot and enjoy B) Experimental factory image flashing over SSH from airOS v6.1.7 1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware no other airOS version is currently supported 2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing 3. cd ubnt-bullet-m2hp-openwrt-flashing 4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin Tested only on Bullet M2HP. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: fix ethernet for f5d8235-v2 boardRoman Yeryomin2018-11-263-2/+14
| | | | | | | | | Belkin F5D8235 v2 has two ethernet switches on board. One internal rt3052 and rtl8366rb on rgmii interface. Looks like internal switch settings were lost in translation to device tree infrastructure. Signed-off-by: Roman Yeryomin <roman@advem.lv>
* ramips: add support for Skylab SKW92A in EVBRussell Senior2018-11-266-0/+143
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifically, SKW92A_E16, described here: http://www.skylabmodule.com/wp-content/uploads/SkyLab_SKW92A_V1.04_datasheet.pdf Specification: - MediaTek MT7628N/N (580 Mhz) - 64 MB of RAM - 16 MB of FLASH - 2T2R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x u.FL - Power by micro-USB connector at USB1 on EVB - UART via micro-USB connector at USB3 on EVB (57600 8n1) - 5x Ethernet LEDs - 1x WLAN LEDs - 1x WPS LED connected by jumper wire from I2S_CK on J20 to WPS_LED pin hole next to daughter board on EVB - WPS/Reset button (S2 on EVB) - RESET button (S1 on EVB) is *not* connected to RST hole next to daughter board Flash instruction: >From Skylab firmware: 1. Associate with SKYLAP_AP 2. In a browser, load: http://10.10.10.254/ 3. Username/password: admin/admin 4. In web admin interface: Administration / Upload Firmware, browse to sysupgrade image, apply, flash will fail with a message: Not a valid firmware. *** Warning: "/var/tmpFW" has corrupted data! 5. Telnet to 10.10.10.254, drops you into a root shell with no credentials 6. # cd /var 7. # mtd_write -r write tmpFW mtd4 Unlocking mtd4 ... Writing from tmpFW to mtd4 ... [e] 8. When flash has completed, you will have booted into your firmware. >From U-boot via TFTP and initramfs: 1. Place openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin on a TFTP server 2. Connect to serial console at USB3 on EVB 3. Connect ethernet between port 1 (not WAN) and your TFTP server (e.g. 192.168.11.20) 4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC 5. Apply power to EVB 6. Interrupt u-boot with keypress of "1" 7. At u-boot prompts: Input device IP (10.10.10.123) ==:192.168.11.21 Input server IP (10.10.10.3) ==:192.168.11.20 Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin 8. Move ethernet to port 0 (WAN) on EVB 9. At new OpenWrt console shell, fetch squashfs-sysupgrade image and flash with sysupgrade. >From U-boot via TFTP direct flash: 1. Place openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin on a TFTP server 2. Connect to serial console at USB3 on EVB (57600 8N1) 3. Connect ethernet between port 1 (not WAN) an your TFTP server (e.g. 192.168.11.20) 4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC 5. Apply power to EVB 6. Interrupt u-boot with keypress of "2" 7. At u-boot prompts: Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y Input device IP (10.10.10.123) ==:192.168.11.21 Input server IP (10.10.10.3) ==:192.168.11.20 Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin 8. When transfer is complete or as OpenWrt begins booting, move ethernet to port 0 (WAN). Signed-off-by: Russell Senior <russell@personaltelco.net>
* rb532: drop 4.9 supportRoman Yeryomin2018-11-2610-672/+0
| | | | Signed-off-by: Roman Yeryomin <roman@advem.lv>
* rb532: switch to 4.14Roman Yeryomin2018-11-261-1/+1
| | | | Signed-off-by: Roman Yeryomin <roman@advem.lv>
* rb532: add 4.14 supportRoman Yeryomin2018-11-2610-0/+672
| | | | Signed-off-by: Roman Yeryomin <roman@advem.lv>
* lantiq/basefiles: use shutdown instead of stop when the system goes downMartin Schiller2018-11-251-1/+1
| | | | | | I can't see any reason why we shouldn't use shutdown for lantiq as well. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* imx6: image: ventana: Add missing BOOT_SCRIPT variablePetr Štetiar2018-11-251-0/+1
| | | | | | | | | | This is probably theoretical problem as the Ventana is defined first in the image Makefile, but once the position of the definition would change in the future (alphabetical sorting?) it would get bootscript from the previous board which would have BOOT_SCRIPT set. Cc: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: select kmod-mt76x0e for TP-Link ArcherC20i and wr902ac-v3Daniel Golle2018-11-252-1/+2
| | | | | | | | | Both devices come with a MediaTek MT7610E 5GHz 802.11ac 1T1R radio which wasn't supported at the time the devices were added to OpenWrt. Now that we got it, include kmod-mt76x0e in images for those devices. Reported-by: Arian Sanusi <openwrt@semioptimal.net> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: enable CONFIG_BRIDGE_VLAN_FILTERINGDaniel Golle2018-11-252-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This allows us to use the bridge as a managed switch and gracefully handle mixed tagged and untagged frames. Prior to this, the only alternative was creating one bridge per vlan which quickly becomes a nightmare and still won't let you mix both tagged and untagged frames on the physical port without some complex ebtables magic. This is in line with the notion that OpenWRT is the network go-to swiss army knife when you need a nice set-and-forget, low maintenance box to handle a specific task. Current builds of the ip-bridge package already fully support this feature so the only requirement is enabling the kernel config. This is disabled by default so existing bridge configurations will not be affected. This patch only gives the ability to turn it on with an 'ip link' command. If there is interest, I could look into making the feature accessible via uci configuration. It causes about 3.1% hit on raw bridging speed, which is relatively trivial considering that I had to use 300 byte packets to strain the CPU enough to notice a slowdown at all. The ER8 would chug along at wire speed otherwise, and that's using only one core. Since the typical bridge use case on OpenWRT is wireless, I doubt it would be noticeable at all. With BRIDGE_VLAN_FILTERING iperf -u -c 192.168.1.105 -b 1G -l 300 ------------------------------------------------------------ Client connecting to 192.168.1.105, UDP port 5001 Sending 300 byte datagrams, IPG target: 2.24 us (kalman adjust) UDP buffer size: 208 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.1.12 port 58045 connected with 192.168.1.105 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 977 MBytes 820 Mbits/sec [ 3] Sent 3414986 datagrams [ 3] Server Report: [ 3] 0.0-10.0 sec 811 MBytes 680 Mbits/sec 0.000 ms 581210/3414986 (0%) Without BRIDGE_VLAN_FILTERING iperf -u -c 192.168.1.105 -b 1G -l 300 ------------------------------------------------------------ Client connecting to 192.168.1.105, UDP port 5001 Sending 300 byte datagrams, IPG target: 2.24 us (kalman adjust) UDP buffer size: 208 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.1.12 port 36645 connected with 192.168.1.105 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 977 MBytes 820 Mbits/sec [ 3] Sent 3414990 datagrams [ 3] Server Report: [ 3] 0.0-10.0 sec 836 MBytes 701 Mbits/sec 0.000 ms 493950/3414990 (0%) In terms of kernel size, it uses 16KB (6753K vs 6737K on ER8) so a 0.002% hit. The exact 16KB is probably just due to how the kernel is compressed. Suggested-by: Jonathan Thibault <jonathan@navigue.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: specify "firmware" partition format for Ubiquiti UniFiRafał Miłecki2018-11-241-0/+1
| | | | | | | | | | | | This affects: 1. Ubiquiti UniFi-AC-LITE/LR 2. Ubiquiti UniFi-AC-PRO 3. Ubiquiti UniFi-AC-MESH 4. Ubiquiti UniFi-AC-MESH PRO Succesfully tested on UniFi AP AC Pro. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: specify "firmware" partition format for WNDR3700 and v2Hannu Nyman2018-11-242-0/+2
| | | | | | | | Specify the new "firmware" partition format for Netgear WNDR3700 and WNDR3700v2 similarly as ffd082aa did for WNDR3800, the third device in the family. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ath79: specify "firmware" partition format for TP-LINK Archer C7 v2Rafał Miłecki2018-11-241-1/+2
| | | | | | With this change it doesn't require trying parsers one by one. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: drop unused arch_split_mtd_part()Rafał Miłecki2018-11-248-52/+18
| | | | | | | No single target/arch uses it and most likely there is no need to make such a potential code target/arch specific. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: add missing version.h include to the TP-LINK parserRafał Miłecki2018-11-241-0/+1
| | | | | Fixes: a29c8d685be7 ("kernel: add DT binding support to the TP-LINK parser") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: add DT binding support to the TP-LINK parserRafał Miłecki2018-11-241-0/+10
| | | | | | It allows triggering it directly by specifying format in the DT. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: specify "firmware" partition format for Netgear WNDR3800Rafał Miłecki2018-11-241-0/+1
| | | | | | It doesn't require trying parsers one by one. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: add DT binding support to the uimage parsersRafał Miłecki2018-11-241-0/+21
| | | | | | It allows specifying default and Netgear parsers directly in the DT. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: don't auto-split "firmware" if it has "compatible" DT propertyRafał Miłecki2018-11-248-18/+20
| | | | | | | | | If "compatible" is being used that should trigger a proper parser directly. It's more reliable thanks to not trying parsers one by one. In such case partition shouldn't be split automatically to avoid parsing it twice. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: b53: register switch on probeDavid Bauer2018-11-231-22/+21
| | | | | | | | | | | | | Currently, the b53 MDIO switch driver registers the switch on config-init and not on device probe. Because of this, the switch gets added every time the associated interface comes up. This commit fixes this behavior by registering the switch on device probe. Compile- and run-tested on OCEDO Koala. Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: bump 3.18 to 3.18.126Koen Vandeputte2018-11-222-2/+2
| | | | | | | | | Refreshed all patches. Compile-tested: adm5120 Runtime-tested: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.82Koen Vandeputte2018-11-224-6/+6
| | | | | | | | | | | Refreshed all patches. Compile-tested: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested: ar71xx, cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 11:15:51 +0000