aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* kernel: bump 5.10 to 5.10.27Kevin Darbyshire-Bryant2021-04-0320-58/+62
| | | | | | | | | | | | | | | | Use update_kernel to refresh all patches, required manual updates to: 610-netfilter_match_bypass_default_checks.patch 611-netfilter_match_bypass_default_table.patch 762-net-bridge-switchdev-Refactor-br_switchdev_fdb_notif.patch 764-net-bridge-switchdev-Send-FDB-notifications-for-host.patch Run-tested: x86_64 Nothing screamed out but any funny business with linux bridging should suspect this update first. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* realtek: rename partitions in Netgear DTSIStijn Segers2021-04-031-5/+5
| | | | | | | | | Switch the Netgear DTSI for the Realtek target from the OEM partition naming scheme to accepted OpenWrt naming practices. A quick git grep for 'u-boot-env' e.g. in the OpenWrt tree turns up almost 500 hits whereas grepping for 'bdinfo' (the OEM equivalent) returns a meagre 14. Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* lantiq: add basic support for AVM FRITZ!Box 3390Andreas Böhler2021-04-036-1/+328
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The FRITZ!Box 3390 actually contains two SoCs, one Lantiq with a 5GHz WiFi and one AR9342 with a 2.4GHz WiFi. Only the Lantiq has access to the flash memory, the Atheros runs fully from RAM. Specifications -------------- - Lantiq 500 MHz - 128MiB RAM - 128MiB NAND - 256k Flash - AR9580 5GHz WiFi - AR9342 560 MHz - 64MiB RAM - AR9328 2.4GHz WiFi Remarks ------- This commit only adds support for the Lantiq side of things and prepares the drivers for communication with the Atheros SoC. Thus, only 5GHz WiFi works by default, the 2.4GHz WiFi will be added via another target. Some kernel patches will be required to add support for the Atheros SoC. Installation ------------ Use the eva_ramboot.py script to boot the initramfs image. Then, transfer the sysupgrade image to the device and run sysupgrade to flash it to the NAND. Signed-off-by: Andreas Böhler <dev@aboehler.at> Acked-by: Aleksander Jan Bajkowski A.Bajkowski@stud.elka.pw.edu.pl Signed-off-by: Joachim Cerny <cocktail_yogi@web.de>
* lantiq: VR9: fix gpio-hog by defining the GPIO rangesJoachim Cerny2021-04-031-0/+1
| | | | | | | | | | defined gpio-ranges according to Reference: https://github.com/torvalds/linux/blob/master/drivers/pinctrl/pinctrl-xway.c#L864 This change is needed by gpio-hog on Fritzbox 3390 thx to @abajk Acked-by: Aleksander Jan Bajkowski A.Bajkowski@stud.elka.pw.edu.pl Signed-off-by: Andreas Böhler <dev@aboehler.at> Signed-off-by: Joachim Cerny <cocktail_yogi@web.de>
* ramips: fix IMAGE_SIZE of HC5x6: fix image size of HC5x61Shiji Yang2021-04-031-3/+3
| | | | | | | | "firmware" partition size defined in the device tree file is 0xf70000, so the right IMAGE_SIZE is 15808k Fixes: df1e5d646345 ("ramips: fix partition layout of hiwifi hc5x61") Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: Fix booting on MQmaker WiTi boardDaniel Engberg2021-04-031-0/+1
| | | | | | | | This fixes the dreaded "lzma error 1" also reported on similar devices Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3057 Fixes: FS#3057 Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* ramips: Fix booting on MTC WR1201René van Dorst2021-04-031-0/+1
| | | | | | | | This fixes the dreaded "lzma error 1" also reported on similar devices Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3057 Fixes: FS#3057 Signed-off-by: René van Dorst <opensource@vdorst.com>
* armvirt: add 5.10 testing kernelAleksander Jan Bajkowski2021-04-031-0/+1
| | | | | | | Add 5.10 as testing kernel. Builds successfully with CONFIG_ALL_KMODS=y enabled. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* armvirt: refresh 5.10 configAleksander Jan Bajkowski2021-04-033-19/+20
| | | | | | | | | | This was done by executing these commands: $ make kernel_oldconfig CONFIG_TARGET=subtarget $ make kernel_oldconfig CONFIG_TARGET=subtarget_platform Some common symbols have been moved to target config. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* armvirt: copy config files for 5.10Aleksander Jan Bajkowski2021-04-033-0/+391
| | | | | | Copy config and patches for 5.10. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* armvirt: refresh 5.4 configAleksander Jan Bajkowski2021-04-033-203/+14
| | | | | | | | This was done by executing these commands: $ make kernel_oldconfig CONFIG_TARGET=subtarget $ make kernel_oldconfig CONFIG_TARGET=subtarget_platform Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* kernel: bump 5.4 to 5.4.109John Audia2021-04-0256-180/+180
| | | | | | | | | | | | | | | | | | | | Ran update_kernel.sh in a fresh clone without any existing toolchains. Manually rebased: pending-5.4/611-netfilter_match_bypass_default_table.patch The upstream change affecting this patch is the revert of an earlier kernel commit. Therefore, we just revert our corresponding changes in [1]. Build system: x86_64 Build-tested: ipq806x/R7800 [1] 9b1b89229f0e ("kernel: bump 5.4 to 5.4.86") Signed-off-by: John Audia <graysky@archlinux.us> [adjust manually rebased patch, add explanation] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm53xx: enhance support for Linksys EA9500Vivek Unune2021-04-014-3/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1. Add leds and configs 2. Add network configs 3. Add script to clear partial boot flag 4. Hack to use port 5 as cpu port as port 8 connected to eth2 wont pass any frames 5. Enable EA9500 image generation Hardware Info: - Processor - Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz - Switch - BCM53012 in BCM4709C0KFEBG & external BCM53125 - DDR3 RAM - 256 MB - Flash - 128 MB (Toshiba TC58BVG0S3HTA00) - 2.4GHz - BCM4366 4×4 2.4/5G single chip 802.11ac SoC - Power Amp - Skyworks SE2623L 2.4 GHz power amp (x4) - 5GHz x 2 - BCM4366 4×4 2.4/5G single chip 802.11ac SoC - Power Amp - PLX Technology PEX8603 3-lane, 3-port PCIe switch - Ports - 8 Ports, 1 WAN Ports - Antennas - 8 Antennas - Serial Port - @j6 [GND,TX,RX] (VCC NC) 115200 8n1 Flashing Instructions: 1. Connect a USB-TTL table to J6 on the router as well as a ethernet cable to a lan port and your PC. 2. Power-on the router. 3. Use putty or a serial port program to view the terminal. Hit Ctrl+C and interrupt the CFE terminal terminal. 4. Setup a TFTP server on your local machine at setup you local IP to 192.168.1.2 5. Start the TFTP Server 6. Run following commands at the CFE terminal flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx2 nvram set bootpartition=0 && nvram set partialboots=0 && nvram commit 7. Reboot router to be presented by OpenWrt Note: Only installation method via serial cable is supported at the moment. The trx firmware has to be flashed to both the partitions using following commands from CFE prompt. This will cover US and Non-US variants. Signed-off-by: Vivek Unune <npcomplete13@gmail.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: use upstream Linksys EA9500 fixesRafał Miłecki2021-04-012-1/+30
| | | | | | One fix was accepted, one was added. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: fix FIT partition parser compatibility issuesDaniel Golle2021-03-312-65/+18
| | | | | | | | | | | | The uImage.FIT partition parser used to squeeze in FIT partitions in the range where partition editor tools (fdisk and such) expect the regular partition. This is confusing people and tools when adding additional partitions on top of the partition used for OpenWrt's uImage.FIT. Instead of squeezing in the additional partitions, rather start with all uImage.FIT partitions at offset 64. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* bcm4908: backport DT patch adding Ethernet MAC addressRafał Miłecki2021-03-311-0/+82
| | | | | | | This tells OS (Linux) where from MAC should be read (bootloader MTD partition). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mediatek: mt7622: improve sysupgrade on MMCDaniel Golle2021-03-311-49/+12
| | | | | | | Use generic functions to acquire rootdev. Make sure to wipe rootfs_data in case of '-n'. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* bmips: backport pinctrl fixesÁlvaro Fernández Rojas2021-03-312-0/+82
| | | | | | Backport some minor upstream fixes for the pinctrl drivers. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ramips: mt7620: ralink-i2s: fix modpost errorIlya Lipnitskiy2021-03-311-1/+2
| | | | | | | | Fixes the following error when building without CONFIG_MODULE_STRIPPED: FATAL: modpost: sound/soc/ralink/snd-soc-ralink-i2s: struct of_device_id is not terminated with a NULL entry! Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* ramips/mt7621: enable support for cpuidleRui Salvaterra2021-03-311-1/+9
| | | | | | | | | | | MIPS Coherent Processor Systems (CPS), which include the MT7621 SoC, support deep sleep idle states and have a specific cpuidle driver for them. Enable support for it, while also switching from constant timer ticks to the idle dynticks model, with the TEO governor. Run-tested on a Redmi AC2100. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ramips/mt7621: drop the timer recalibration patchRui Salvaterra2021-03-313-97/+10
| | | | | | | | | | | | | | | | | We've been carrying this patch for many years [1], in order to fix a timer calibration issue on MT7621. Turns out, after retesting with a recent kernel (Linux 5.10), the system works perfectly fine without it (no rcu_sched stalls or inconsistent BogoMIPS values across CPUs). Manually refreshed: 322-mt7621-fix-cpu-clk-add-clkdev.patch 323-mt7621-memory-detect.patch [1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commitdiff;h=6f4a903533361a2906a4d94ac6f597cd9c6c47bc Suggested-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com> Tested-by: Donald Hoskins <grommish@gmail.com> Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ramips/mt7621: drop the weak reordering patchRui Salvaterra2021-03-312-12/+2
| | | | | | | | | | | | | | | | | | In order to fix random hangs on MT7621, we've been selecting WEAK_REORDERING_BEYOND_LLSC for years [1]. However, these random hangs have been most likely caused by an oversight in the MIPS implementation of the kernel memory consistency model, which has already been fixed for some time (and backported to stable) [2]. Manually refreshed: 321-mt7621-timer.patch [1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commitdiff;h=5c971cd6fdd7298a2017bdb6bea870088eddb8b9 [2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/mips?h=linux-5.4.y&id=42344113ba7a1ed7b5654cd5270af0d5698d8521 Suggested-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com> Tested-by: Donald Hoskins <grommish@gmail.com> Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* sunxi: enable wifi module on Pine64 boardsZoltan HERPAI2021-03-292-0/+74
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Pine64(+) and the SoPine64 baseboard has an optional BT+WiFi module, carrying an RTL8723BS. The wifi part is connected via SDIO, the BT part is connected via UART. The BT part requires additional code changes in the drivers so we'll skip that until 5.10. Aside from a DTS patch to enable the wifi module, add the required packages into the device definitions. [ 8.996970] RTL8723BS: module init start [ 9.000922] RTL8723BS: rtl8723bs v4.3.5.5_12290.20140916_BTCOEX20140507-4E40 [ 9.007965] RTL8723BS: rtl8723bs BT-Coex version = BTCOEX20140507-4E40 [ 9.014785] pnetdev = 000000009bdd5000 [ 9.047780] RTL8723BS: rtw_ndev_init(wlan0) [ 9.053349] RTL8723BS: module init ret =0 root@OpenWrt:/# iw list Wiphy phy0 wiphy index: 0 max # scan SSIDs: 9 max scan IEs length: 2304 bytes max # sched scan SSIDs: 0 max # match sets: 0 Retry short limit: 7 Retry long limit: 4 Coverage class: 0 (up to 0m) Available Antennas: TX 0 RX 0 Supported interface modes: * IBSS * managed * AP * monitor Band 1: Frequencies: * 2412 MHz [1] (20.0 dBm) * 2417 MHz [2] (20.0 dBm) * 2422 MHz [3] (20.0 dBm) * 2427 MHz [4] (20.0 dBm) * 2432 MHz [5] (20.0 dBm) * 2437 MHz [6] (20.0 dBm) * 2442 MHz [7] (20.0 dBm) * 2447 MHz [8] (20.0 dBm) * 2452 MHz [9] (20.0 dBm) * 2457 MHz [10] (20.0 dBm) * 2462 MHz [11] (20.0 dBm) * 2467 MHz [12] (20.0 dBm) (no IR) * 2472 MHz [13] (20.0 dBm) (no IR) * 2484 MHz [14] (20.0 dBm) (no IR) Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* sunxi: enable MUSB in A53 subtargetZoltan HERPAI2021-03-291-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | The Pine64(+) and the SoPine64 baseboard has two USB ports. One of these (the lower) is connected directly to a USB host, the other one's (upper) PHY is shared with the separate OTG controller. In order to get it working, MUSB support needs to be enabled. As there are other targets which compile MUSB support into the kernel and not package it into modules, the same is done here. [ 1.348760] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04 [ 1.357029] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.364250] usb usb5: Product: MUSB HDRC host driver [ 1.369219] usb usb5: Manufacturer: Linux 5.4.99 musb-hcd [ 1.374617] usb usb5: SerialNumber: musb-hdrc.1.auto [ 1.379891] hub 5-0:1.0: USB hub found [ 1.383677] hub 5-0:1.0: 1 port detected [...] [ 697.299440] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 697.461855] usb 1-1: New USB device found, idVendor=090c, idProduct=1000, bcdDevice=11.00 [ 697.470038] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 697.477180] usb 1-1: Product: USB Flash Disk Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* bmips: dts: align LEDsÁlvaro Fernández Rojas2021-03-296-32/+45
| | | | | | Align all bmips devices LED configurations. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: backport accepted pinctrl patchesÁlvaro Fernández Rojas2021-03-2939-2892/+3446
| | | | | | | These patches have been accepted for linux v5.13. External interrupts not supported for now. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: vr-3032u: fix gpio keysÁlvaro Fernández Rojas2021-03-291-2/+2
| | | | | | These GPIO keys were assigned to incorrect pins. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: dgnd3700-v2: fix gpio keysÁlvaro Fernández Rojas2021-03-291-9/+9
| | | | | | These GPIO keys were assigned to incorrect pins. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm53xx: fix Linksys EA9500 partitionsRafał Miłecki2021-03-291-0/+58
| | | | | | Use proper DT binding. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: backport 5.13 mtd partitioning changesRafał Miłecki2021-03-2926-44/+629
| | | | | | | | 1. Use upstream accepted NVMEM patches 2. Minor fix for BCM4908 partitioning 3. Support for Linksys firmware partitions on Northstar Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mvebu: Fix mac addresses for GL.iNet GL-MV1000Sven Eckelmann2021-03-271-0/+4
| | | | | | | | | | | | | The original GL.iNet firmware has two different mac addresses in the factory/art partition. The first one is for the WAN interface only and the second one is for both lan0 and lan1. But the original submission for OpenWrt didn't initialize the mac addresses of the LAN ports for the DSA device at all. The ethernet mac address was then used for all DSA ports. Fixes: 050c24f05c85 ("mvebu: add support for GL.iNet GL-MV1000") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ramips: correct switch config of Youku yk1Shiji Yang2021-03-271-1/+4
| | | | | | | | | | There are only two lan ports and one wan port on Youku yk1 Fixes: e9baf8265bb8 ("ramips: add support for Youku YK1") Signed-off-by: Shiji Yang <yangshiji66@qq.com> [add Fixes:] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.108John Audia2021-03-2716-38/+31
| | | | | | | | | | | | | | | | | All modifications made by by update_kernel.sh. Build system: x86_64 Build-tested: ipq806x/R7800 Run-tested: ipq806x/R7800 [only 5.4.107] No dmesg regressions, everything functional Run-tested by @timocapa: - ramips/mt7621/{Xiaomi R3G, Redmi 2100} - Lantiq/XWAY/Fritz!Box 7320/7330 Signed-off-by: John Audia <graysky@archlinux.us> [squash, edit commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: fix label_mac for NEC Aterm WG1200CRINAGAKI Hiroshi2021-03-271-2/+6
| | | | | | | | | | On NEC Aterm WG1200CR, the MAC address for WAN is printed in the label on the case, not LAN. This patch fixes this issue. Fixes: 50fdc0374b ("ath79: provide label MAC address") Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* mvebu: Add button support for GL.iNet GL-MV1000Sven Eckelmann2021-03-271-0/+17
| | | | | | | | | | | | | The original patch to support this device advertised support for the reset button and the "switch" in the commit message. But neither were actually integrated in the device tree or documented anywere. The button itself is now used to trigger a reset (as described in the official GL.iNet documentation). The switch itself is registered as BTN_0 like other devices from GL.iNet in ath79. Fixes: 050c24f05c85 ("mvebu: add support for GL.iNet GL-MV1000") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* kernel: Move CONFIG_USERIO to generic configHauke Mehrtens2021-03-2715-13/+2
| | | | | | | | The CONFIG_USERIO option is unset in multiple target configurations. On the sunxi target it is activated. Move the kernel configuration option to the generic kernel configuration. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Deactivate CONFIG_VFIO in generic kernel configHauke Mehrtens2021-03-274-3/+1
| | | | | | | | | Instead of deactivating this in every target config, deactivate it once in the generic kernel config. I was asked for this config option in a x86 64 build in OpenWrt 21.02. Fixes: 87046e87e229 ("kernel: add missing kernel config symbol") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: add missing kernel config symbolKevin Darbyshire-Bryant2021-03-271-0/+1
| | | | | | | | | | | | Bump to 5.10.26 reversed dependencies on IOMMU for CONFIG_VFIO thus malta (at least) prompted for this new symbol. Set it to 'false' in the default config. rockchip & X86 enable it in target specific configs. Thanks to Tony Ambardar for falling over this one Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* x86/base-files: add support for Sophos SG/XG-105Stan Grishin2021-03-262-0/+11
| | | | | | | This adds detection of the Sophos SG-105 and Sophos XG-105 models and assignment of ethernet ports these models have to LAN/WAN. Signed-off-by: Stan Grishin <stangri@melmac.net>
* kernel: bump 5.10 to 5.10.26Rui Salvaterra2021-03-263-12/+5
| | | | | | | | | | | | | | Automatically refreshed: ath79/patches-5.10/471-mtd-cfi_cmdset_0002-AMD-chip-0x2201-write-words.patch bcm63xx/patches-5.10/143-gpio-fix-device-tree-gpio-hogs-on-dual-role-gpio-pin.patch generic/hack-5.10/204-module_strip.patch Run-tested: ath79 (TL-WDR3600) x86_64 (APU2 - ldir) Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: create bootfs partition when parsing on BCM4908Rafał Miłecki2021-03-241-5/+9
| | | | | | | | It's helpful for accessing booting data (DTS, kernel, etc.). It has to be used carefully as CFE's JFFS2 support is quite dumb. It doesn't recognize deleted files and has problems handling 0 inode. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mediatek: generate complete sdcard image for BPi-R64Daniel Golle2021-03-241-4/+9
| | | | | | | Populate the recovery and production partitions of the generated sdcard image for the Bananapi BPi-R64. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* bmips: reorganize patchesÁlvaro Fernández Rojas2021-03-244-0/+0
| | | | | | Reorder kernel patches after recent backports. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: switch to upstream ehci overcurrent flagÁlvaro Fernández Rojas2021-03-246-6/+6
| | | | | | | After backporting upstream ehci overcurrent patches we need to use spurious-oc instead of ignore-oc. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: backport ehci overcurrent patchesÁlvaro Fernández Rojas2021-03-247-44/+112
| | | | | | These patches have been accepted for v5.13. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: drop apu2 reboot patchKevin Darbyshire-Bryant2021-03-242-38/+0
| | | | | | | | | | | | | | | | | | | | | | This patch really annoys me, either it needs to go upstream or be dropped, so it's going to be dropped here. Checking drivers/platform/x86/pcengines-apuv2.c it also appears to be incomplete since it mentions different dmi board names depending on bios version. /* APU2 w/ legacy BIOS < 4.0.8 */ is 'APU2' /* APU2 w/ legacy BIOS >= 4.0.8 */ is 'apu2' /* APU2 w/ mainline BIOS */ is 'PC Engines apu2' So the patch, if applicable at all, only 'works' for legacy BIOS >= 4.0.8 My APU2 on mainline BIOS reboots fine without this patch. So let's see if anyone screams and when they do question why legacy bios. If patch DOES need to be re-introduced then it needs to go upstream first. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kernel: bump 5.10 to 5.10.25Kevin Darbyshire-Bryant2021-03-243-5/+5
| | | | | | | | | | | Straightforward refresh of patches using update_kernel. Removed (reverse-applicable): bmips/patches-5.10/010-v5.11-net-dsa-implement-a-central-TX-reallocation-procedur.patch Run tested: x86_64 (apu2) Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kernel: bump 5.10 to 5.10.24Kevin Darbyshire-Bryant2021-03-2421-143/+39
| | | | | | | | Straightforward refresh of patches using update_kernel. Run tested: x86_64 (apu2) Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* bmips: add wifi packages for supported devicesÁlvaro Fernández Rojas2021-03-233-5/+7
| | | | | | Netgear DGND3700v2 / Comtrend VR-3032u internal wireless not supported. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: add ATH9K PCI fixupsÁlvaro Fernández Rojas2021-03-233-1/+256
| | | | | | | Add support for registering ATH9K PCI fixups needed to bring up wifi on some devices. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>