aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
...
* ramips: remove redundant mtd-eeprom in mt76x8 DTS filesAdrian Schmutzler2019-10-278-9/+0
| | | | | | | | | | In mt7628an.dtsi, calibration data for wmac is already defined: mediatek,mtd-eeprom = <&factory 0x0>; Thus, this patch removes redundant entries of this property in derived DTS files. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove redundant mtd-mac-address for WiFiAdrian Schmutzler2019-10-273-4/+1
| | | | | | | | | | When caldata locations are defined with mediatek,mtd-eeprom the MAC address is automatically read from offset +4. Thus, specifying that location explicitly is redundant. This patch removes those redundant definitions. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: mtd: spinand: Backport chip definitionsJeff Kletsky2019-10-249-11/+870
| | | | | | | | | | | | | | | | | | | | | | | | | | generic: Add/rename patches for upstream consistency ipq40xx: generic-level patch replaces same-source patches-4.19/ 082-v4.20-mtd-spinand-winbond-Add-support-for-W25N01GV.patch The SPI-NAND framework from Linux uses common driver code that is then "tuned" by a tiny struct of chip-specific data that describes available commands, timing, and layout (data and OOB data). Several manufacturers and chips have been added since 4.19, several of which are used in devices already supported by OpenWrt (typically with no or "legacy" access to their NAND memory). This commit catches up the supported-chip definitions through Linux 5.2-rc6 and linux/next. The driver is only compiled for platforms with CONFIG_MTD_SPI_NAND=y. This presently includes ipq40xx and pistachio, with the addition of ath79-nand in these commits (and not ath79-generic or ath79-tiny). Upstream patches refreshed against 4.19.75 Build-tested-on: ipq40xx Run-tested-on: ath79-nand Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ath79: Refactor GL.iNet GL-AR300M-series generic.mkJeff Kletsky2019-10-241-3/+3
| | | | | | | | | | Rework DEVICE_VENDOR, DEVICE_MODEL, and DEVICE_VARIANT for the GL-AR300M series on the ath79-generic target. Changes GL-AR300M-Lite to the current form with DEVICE_VARIANT := Lite (board name is unchanged) Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ath79: GL-AR750S: Add I2C SupportJeff Kletsky2019-10-241-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | The GL-AR750S has an internal header for I2C. Provide DTS definitions for the i2c-gpio driver. The I2C drivers; kmod-i2c-core, kmod-i2c-gpio consume ~20 kB of flash and can be loaded as modules, Default clock measured ~11.2 ms period, ~89 kHz The board has well-labeled (unpopulated) headers for serial and I2C along the front edge of the board (the edge with the LEDs). Looking from the top, rear of the unit (behind Ethernet jacks) ------------------------------------------- 5G_LED 2G_LED PWR_LED O O O O O O O 3 S S G T R G V C D N X X N 3 L A D D Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ath79: GL-AR300M series: Add I2C SupportJeff Kletsky2019-10-241-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The GL-AR300M series have an internal header for I2C. Provide DTS definitions for the i2c-gpio driver. The I2C drivers; kmod-i2c-core, kmod-i2c-gpio consume ~20 kB of flash and can be loaded as modules, Default clock measured ~11.4 ms period, ~88 kHz The board has two sets of (unpopulated) headers. While facing the back of the board (looking into the Ethernet jacks), and looking from the top, the one on the left edge of the baord with four holes is the I2C header. It appears to be labeled J8 on "GL-AR300M-V1.4.0" boards. | (Patch antenna) | | | O GND | O SDA / GPIO 17 | O SCL / GPIO 16 | ⊡ 3V3 (square land) | | (Ethernet jacks) https://docs.gl-inet.com/en/3/hardware/ar300m/#pcb-pinout states "Note: I2C is not working in some early version of the router." Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* ramips: add support for Asus RT-AC65PGabor Varga2019-10-246-155/+190
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Asus RT-AC65P router is identical with the RT-AC85P, but better to make separate images for it. On both routers the installation can be done also via SSH: Note: The user/password for SSH is identical with the one used in the Web-interface. 1. Complete the initial setup wizard. 2. Activate SSH under "Administration" -> "System". 3. Transfer the OpenWrt factory image via scp: > scp openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin admin@192.168.50.1:/tmp 4. Connect via SSH to the router. > ssh admin@192.168.50.1 5. Write the OpenWrt image to flash. > mtd-write -i /tmp/openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin -d linux 6. Reboot the router > reboot Changelog: v3: removed [] from filename, rebased to latest master v2: Rebased to latest master v1: Initial release Signed-off-by: Gabor Varga <vargagab@gmail.com>
* ar71xx: add model detection for UniFi AC-LRAndreas Ziegler2019-10-232-0/+9
| | | | | | | | | | | | | | This commit adds correct model detection for UniFi AC-LR. Previously, said device was incorrectly detected as UniFi-AC-LITE/MESH. The Information about the device is stored at 0xC in the EEPROM partition. It corresponds to the sysid in /etc/board.info of the Ubiquiti stock firmware. Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de> [adjust naming style of target to existing ones] Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: add support for AVM FRITZ!Repeater 1200David Bauer2019-10-238-6/+551
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: Qualcomm IPQ4019 RAM: 256M DDR3 FLASH: 128M NAND WiFi: 2T2R IPQ4019 bgn 2T2R IPQ4019 a/n/ac ETH: Atheros AR8033 RGMII PHY BTN: 1x Connect (WPS) LED: Power (green/red/yellow) Installation ------------ 1. Grab the uboot for the Device from the 'u-boot-fritz1200' subdirectory. Place it in the same directory as the 'eva_ramboot.py' script. It is located in the 'scripts/flashing' subdirectory of the OpenWRT tree. 2. Assign yourself the IP address 192.168.178.10/24. Connect your Computer to one of the boxes LAN ports. 3. Connect Power to the Box. As soon as the LAN port of your computer shows link, load the U-Boot to the box using following command. > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz1200.bin 4. The U-Boot will now start. Now assign yourself the IP address 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP server root directory and rename it to 'FRITZ1200.bin'. 5. The Box will now boot OpenWRT from RAM. This can take up to two minutes. 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using scp. SSH into the Box and first write the Bootloader to both previous kernel partitions. > mtd write /path/to/uboot-fritz1200.bin uboot0 > mtd write /path/to/uboot-fritz1200.bin uboot1 7. Remove the AVM filesystem partitions to make room for our kernel + rootfs + overlayfs. > ubirmvol /dev/ubi0 --name=avm_filesys_0 > ubirmvol /dev/ubi0 --name=avm_filesys_1 8. Flash OpenWRT peristently using sysupgrade. > sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: add missing backslash in 11-ath10k-caldataDavid Bauer2019-10-231-1/+1
| | | | | | | This adds a missing backslash in the caldata-extraction script. Without this fix, caldata extraction fails for every device. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: fix ethernet probe abort on missing phy-resetDavid Bauer2019-10-231-1/+1
| | | | | | | This commit completely fixes the abortion of the ipq40xx ethernet driver probe in case no phy-reset is defined. Signed-off-by: David Bauer <mail@david-bauer.net>
* brcm63xx: split up DEVICE_TITLEMoritz Warning2019-10-221-91/+219
| | | | | | | DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Uses DEVICE_ALT* variables for alternative vendor/retailer names. Signed-off-by: Moritz Warning <moritzwarning@web.de>
* brcm63xx: fix build with GCC 8.3Jonas Gorski2019-10-221-0/+93
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes the following build error when building when using GCC 8.3: In file included from ./include/linux/string.h:19, from ./include/linux/bitmap.h:9, from ./include/linux/cpumask.h:12, from ./arch/mips/include/asm/processor.h:15, from ./arch/mips/include/asm/thread_info.h:16, from ./include/linux/thread_info.h:38, from ./include/asm-generic/preempt.h:5, from ./arch/mips/include/generated/asm/preempt.h:1, from ./include/linux/preempt.h:81, from ./include/linux/spinlock.h:51, from ./include/linux/mmzone.h:8, from ./include/linux/bootmem.h:8, from arch/mips/bcm63xx/prom.c:10: arch/mips/bcm63xx/prom.c: In function 'prom_init': ./arch/mips/include/asm/string.h:162:11: error: '__builtin_memcpy' forming offset [2, 32] is out of the bounds [0, 1] of object 'bmips_smp_movevec' with type 'char' [-Werror=array-bounds] __ret = __builtin_memcpy((dst), (src), __len); \ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ arch/mips/bcm63xx/prom.c:97:3: note: in expansion of macro 'memcpy' memcpy((void *)0xa0000200, &bmips_smp_movevec, 0x20); ^~~~~~ In file included from arch/mips/bcm63xx/prom.c:14: ./arch/mips/include/asm/bmips.h:80:13: note: 'bmips_smp_movevec' declared here extern char bmips_smp_movevec; Reported-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* ramips: fix LAN/WAN MAC addresses of Xiaomi MiWiFi Mini boardAdrian Schmutzler2019-10-221-3/+1
| | | | | | | | | | | | | | | | | | | Based on stock firmware tests, both LAN and WAN ports use the MAC address from 0x28 on factory partition. In OpenWrt, this one is already set in DTS. This patch removes the local bit set in 02_network previously, and adjusts LAN/WAN addresses as on stock firmware. Note that in tests we found a MAC address in 0x2e that is the one in 0x28 plus 1. Since stock firmware does not use it though, we do not use it either. Thanks to Chih-Wei Chen for testing this on his device. ref: https://github.com/openwrt/openwrt/pull/2497 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: fix optional gpio-resetJohn Crispin2019-10-221-1/+1
| | | | | | If a gpio reset pin was not defined we should not bog out. Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: improve support for TP-Link CPE510 v2Adrian Schmutzler2019-10-217-21/+53
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes commit bae927c551fd ("ar71xx: add support for TP-LINK CPE510 V2.0") where the support for this device wasn't optimal. Device support for the CPE510v2 so far has been a hack to enable flashing with CPE510v1 images. Those even have different hardware (e.g. additional ethernet port). With this patch, we provide proper support for this device in ar71xx. Installation: - Flash factory image through stock firmware WEB UI or through TFTP - To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. - Rename factory image to recovery.bin - Stock TFTP server IP: 192.168.0.100 - Stock device TFTP address: 192.168.0.254 Fixes: bae927c551fd ("ar71xx: add support for TP-LINK CPE510 V2.0") Signed-off-by: Andrew Cameron <apcameron@softhome.net> [Rebased onto revert commit, changed comments in mach-cpe510.c, changed commit title and description, fixed eth0 MAC address, removed eth1 initialization] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [squashed revert, added fixes tag] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: fix TARGET_DEVICES after UniElec renameAdrian Schmutzler2019-10-212-3/+3
| | | | | | | | | | Device node names were updated, but updating TARGET_DEVICES was overlooked. Fixes: 4408723d42e0 ("ramips: remove RAM size from device name for UniElec devices") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove RAM size from device name for UniElec devicesAdrian Schmutzler2019-10-217-18/+19
| | | | | | | | | | | UniElec devices are the last ones in ramips target still having the RAM size in device name although RAM size is auto-detected. Remove this from device name, compatible, etc., as it's not required and might be misleading to users and developers adding device support copying those devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: base-files: disable sysupgrade for routerstations and ja76pf2Tomasz Maciej Nowak2019-10-211-2/+2
| | | | | | | | | | Previous commit 0cc87b3 "ath79: image: disable sysupgrade images for routerstations and ja76pf2" doesn't remedy completely the posibility of bricking the device, since user could try to downgrade with an older image. Therefore disable sysupgrade code for these boards with a small note. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ath79: apply alphabetical sorting to entries in 10_fix_wifi_macAdrian Schmutzler2019-10-211-4/+4
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: remove empty default case in 10_fix_wifi_macAdrian Schmutzler2019-10-211-2/+0
| | | | | | This removes a useless empty default case. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: fix whitespaces in 10_fix_wifi_macAdrian Schmutzler2019-10-211-8/+7
| | | | | | | This converts leading whitespaces to tabs and removes a double newline at the end of the file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips/mt762x: convert devices to interrupt-driven gpio-keysAdrian Schmutzler2019-10-21161-314/+197
| | | | | | | | | | | This converts all remaining devices to use interrupt-driven gpio-keys compatible instead of gpio-keys-polled. The poll-interval is removed. While at it, add/remove newlines in keys and leds node where necessary. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add LED migration for several Archer Cxx devicesAdrian Schmutzler2019-10-211-3/+9
| | | | | | | | | Several Archer Cxx devices were using board-specific LED names in ar71xx, which were changed to "tp-link:*" in ath79. This patch adds migration for them. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: use board name in LED migrationsAdrian Schmutzler2019-10-211-4/+3
| | | | | | | | | | | | | Several devices added to LED migration script will just have their (old) board name converted to tp-link. By using a variable for this, the amount of code in the migration script can be reduced and the chance for typos is reduced. This patch also introduces the marker for beginning of a pattern "^" to the regex, so the match is more specific. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix whitespace issues in DTS filesAdrian Schmutzler2019-10-2127-37/+4
| | | | | | | | | This is the result of grepping/searching for several common whitespace issues like double empty lines, leading spaces, etc. This patch fixes them for the ramips target. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: fix SUPPORTED_DEVICES for ubnt_nanostation-mAdrian Schmutzler2019-10-211-1/+1
| | | | | | | | | | | | | The ar71xx images for the Ubiquiti NanoStation M (XM) devices use "nanostation-m" as board name, but the ath79 images are only compatible with the "nano-m" board name, so sysupgrade complains. By changing this additional supported device, sysupgrade smoothly upgrades from ar71xx to ath79. Ref: openwrt#2418 Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* lantiq: modify ath9k caldata extraction to reuse caldata.shAdrian Schmutzler2019-10-211-47/+15
| | | | | | | | | | | | | | | | In lantiq, ath9k caldata extraction is implemented to work in two alternate "modes", the standard one and another one with swapped byte pairs. This rearranges the functions so "standard" use is based on the caldata.sh library, while only a single local function is required for the special case. Note that while the parameter for switching between normal and swab is removed, the size of the caldata is added to the function calls to stay consistent. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: WNDR4300: fix WAN LED behaviourMichal Cieslakiewicz2019-10-211-2/+1
| | | | | | | | | Change WAN LED behaviour to be consistent with other Netgear routers running OpenWrt. Instead of link speed, use amber colour to indicate link status. Green LED should be used when Internet connection is up and running. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ar71xx: WNDR4300: use standard labels for buttonsMichal Cieslakiewicz2019-10-211-3/+3
| | | | | | | GPIO key labels have been changed to standard ones (rfkill, reset, wps). It does not affect button functionality. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: fix patching ath9k MAC address for MyNet WiFi Range ExtenderAdrian Schmutzler2019-10-211-1/+1
| | | | | | | | | | | | | | | | | The code line patching ath9k MAC address for this device contains a wrong number of arguments including an unset "$mac", which looks like a typo or copy/paste mistake. This has been introduced already in the device support commit 745dee11ac78 ("ath79: add support for WD My Net Wi-Fi Range Extender"). This patch just removes the "$mac" argument, leaving a formally valid line. (No on-device test has been performed.) Cc: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for Netgear WNR1000 v2Michal Cieslakiewicz2019-10-215-0/+218
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds ath79 support for Netgear WNR1000v2. Router was previously supported by ar71xx target only. Note: this is a 4_32 device with limited upgrade capabilities. Specification ============= * Description: Netgear WNR1000 v2 * Loader: U-boot * SOC: Atheros AR7240 (340 MHz) * RAM: 32 MiB * Flash: 4 MiB (SPI NOR) - U-boot binary: 256 KiB - U-boot environment: 64 KiB - Firmware: 3712 KiB - ART: 64 KiB * Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN * Wireless: 2.4 GHz b/g/n (Atheros AR9285) * USB: no * Buttons: - Reset - WiFi (rfkill) - WPS * LEDs: - Power (amber/green) - WAN (amber/green) - WLAN (blue) - 4 x LAN (amber/green) - WPS (green) * UART: 4-pin connector JP2, 3.3V (Vcc, TX, RX, GND), 115200 8N1 * Power supply: DC 12V 1A * MAC addresses: LAN on case label, WAN +1, WLAN +2 Installation ============ * TFTP recovery * TFTP via U-boot prompt * sysupgrade * Web interface Test build configuration ======================== CONFIG_TARGET_ath79=y CONFIG_TARGET_ath79_tiny=y CONFIG_TARGET_ath79_tiny_DEVICE_netgear_wnr1000-v2=y CONFIG_ALL_KMODS=y CONFIG_DEVEL=y CONFIG_CCACHE=y CONFIG_COLLECT_KERNEL_DEBUG=y CONFIG_IMAGEOPT=y CONFIG_KERNEL_DEBUG_INFO=y CONFIG_KERNEL_DEBUG_KERNEL=y Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add support for Netgear WNR2000 v3Michal Cieslakiewicz2019-10-215-0/+236
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds ath79 support for Netgear WNR2000v3. Router was previously supported by ar71xx target only. Note: this is a 4_32 device with limited upgrade capabilities. Specification ============= * Description: Netgear WNR2000 v3 * Loader: U-boot * SOC: Atheros AR7241 (360 MHz) * RAM: 32 MiB * Flash: 4 MiB (SPI NOR) - U-boot binary: 256 KiB - U-boot environment: 64 KiB - Firmware: 3712 KiB - ART: 64 KiB * Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN * Wireless: 2.4 GHz b/g/n (Atheros AR9287) * USB: no * Buttons: - Reset - WiFi (rfkill) - WPS * LEDs: - Power (amber/green) - WAN (amber/green) - WLAN (blue) - 4 x LAN (amber/green) - WPS (green) * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1 * Power supply: DC 12V 1A * MAC addresses: LAN on case label, WAN +1, WLAN +2 Installation ============ * TFTP recovery * TFTP via U-boot prompt * sysupgrade * Web interface Test build configuration ======================== CONFIG_TARGET_ath79=y CONFIG_TARGET_ath79_tiny=y CONFIG_TARGET_ath79_tiny_DEVICE_netgear_wnr2000-v3=y CONFIG_ALL_KMODS=y CONFIG_DEVEL=y CONFIG_CCACHE=y CONFIG_COLLECT_KERNEL_DEBUG=y CONFIG_IMAGEOPT=y CONFIG_KERNEL_DEBUG_INFO=y CONFIG_KERNEL_DEBUG_KERNEL=y Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: WNR612v2: improve device supportMichal Cieslakiewicz2019-10-214-10/+19
| | | | | | | | | | | | | | | This patch improves ath79 support for Netgear WNR612v2. Router functionality becomes identical to ar71xx version. Changes include: * software control over LAN LEDs via sysfs * correct MAC addresses for network interfaces * correct image size in device definition * dts: 'keys' renamed to 'ath9k-keys' * dts: 'label-mac-device' set to eth1 (LAN) * dts: formatting adjustments Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add LAN LEDs control bits for AR724x GPIO function pinmuxMichal Cieslakiewicz2019-10-211-1/+9
| | | | | | | | | | | | | | | Currently AR724x pinmux for register 0x18040028 controls only JTAG disable bit. This patch adds new DTS settings to control LAN LEDs and CLKs that allow full software control over these diodes - exactly the same is done by ar71xx target in device setup phase for many routers (WNR2000v3 for example). 'switch_led_disable_pins' clears AR724X_GPIO_FUNC_ETH_SWITCH_LED[0-4]_EN bits. 'clks_disable_pins' clears AR724X_GPIO_FUNC_CLK_OBS[1-5]_EN and AR724X_GPIO_FUNC_GE0_MII_CLK_EN bits. These all should be used together, along with 'jtag_disable_pins', to allow OS to control all GPIO-connected LEDs and buttons on device. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* ath79: add support for Sitecom WLR-7100Tomasz Maciej Nowak2019-10-215-2/+195
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Sitecom WLR-7100 v1 002 (marketed as X7 AC1200) is a dual band wireless router. Specification SoC: Atheros AR1022 RAM: 64 MB DDR2 Flash: 8 MB SPI NOR WIFI: 2.4 GHz 2T2R integrated 5 GHz 2T2R QCA9882 integrated (connected to PCIe lane) Ethernet: 5x 10/100/1000 Mbps QCA8337N USB: 1x 2.0 LEDS: 4x GPIO controlled, 5x switch Buttons: 2x GPIO controlled UART: row of 4 unpopulated holes near USB port, starting count from white triangle on PCB 1. VCC 3.3V, 2. GND, 3. TX, 4. RX baud: 115200, parity: none, flow control: none Installation 1. Connect to one of LAN (yellow) ethernet ports, 2. Open router configuration interface, 3. Go to Toolbox > Firmware, 4. Browse for OpenWrt factory image with dlf extension and hit Apply, 5. Wait few minutes, after the Power LED will stop blinking, the router is ready for configuration. Known issues 5GHz LED doesn't work Additional information When TX line on UART is connected, and board is switched on from power off state, the DDR memory training may fail. If connected to UART, when prompted for number on boot, one can enter number 4 to open bootloader (U-Boot) command line. OEM firmware shell password is: SitecomSenao useful for creating backup of original firmware. There is also another revision of this device (v1 001), which may or may not work with introduced images. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ipq40xx: Add support for Unielec U4019Kristian Evensen2019-10-217-11/+410
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the 32MB storage/512MB RAM version of the U4019 IPQ4019-based board from Unielec. The board has the following specifications: * Qualcomm IPQ4019 (running at 717MHz) * 512MB DDR3 RAM (optional 256MB/1GB) * 32MB SPI NOR (optional 8/16MB or NAND) * Five gigabit ports (Qualcomm QCA8075) * 1x 2.4 GHz wifi (QCA4019 hw1.0) * 1x 5 Ghz wifi (QCA4019 hw1.0) * 1x mini-PCIe slot (only USB-pins connected) * 1x SIM slot (mini-SIM) * 1x USB2.0 port * 1x button * 1x controllable LED * 1x micro SD-card reader Working: * Ethernet * Wifi * USB-port * mini-PCIe slot + SIM slot * Button * Sysupgrade Not working: * SD card slot (no upstream support) Installation instructions: In order to install OpenWRT on the U4019, you need to go via the initramfs-image. The installation steps are as follows: * Connect to board via serial (header exposed and clearly marked). * Interrupt bootloader by pressing a button. * Copy the initramfs-image to your tftp folder, call the file C0A80079.img. * Give the network interface connected to the U4019 the address 192.168.0.156/24. * Start your tftp-server and run tftpboot on the board. * Run bootm when the file has been transferred, to boot OpenWRT. * Once OpenWRT has booted, copy the sysupgrade-image to the device and run sysupgrade to install OpenWRT on the U4019. Notes: - Since IPQ4019 has been moved to 4.19, I have not added support for kernel 4.14. - There is a bug with hardware encryption on IPQ4019, causing poor performance with TCP and ipsec (see for example FS#2355). In order to improve performance, I have disabled hardware encryption in the DTS. We can enable hw. enc. once/if bug is fixed. - In order for Ethernet to work, the phy has to be reset by setting gpio 47 low/high. Adding support for phy reset via gpio required patching the mdio-driver, and the code added comes from the vendor driver. I do not know if patching the driver is an acceptable approach or not. v1->v2: * Do not use wildcard as identifier in the board.d-scripts (thanks Adrian Schmutzler). Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ath79: fix gigabit link pll-data for EX7300Daniel Gimpelevich2019-10-211-2/+2
| | | | | | | | | | | | | The device did not appear to be reachable unless the connection were forced to 100Mb or lower. Revert to previously working pll-data. Also fix the phy-mode to represent the actual state needed for ethernet to function. Reported-by: Moritz Schreiber <moritz@mosos.de> Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [add remark about phy-mode property] Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add AR934x NAND Flash Controller driverMichal Cieslakiewicz2019-10-204-0/+1525
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch contains updated driver for Atheros NAND Flash Controller written originally by Gabor Juhos for ar71xx (aka 'ar934x-nfc'). ath79 version has adapted to work with kernel 4.19 and Device Tree. It has also been renamed to 'ar934x-nand' to avoid confusion with Near-Field Communication technology. Controller is present on Atheros AR934x SoCs and required for accessing internal flash storage on routers like Netgear WNDR4300. This port preserves all NAND programming code while moving platform configuration to Device Tree and replacing some kernel functions marked for retirement by 4.19. Suitable definition is included in 'ar934x.dtsi' ('nand@1b000200' section). Most important changes to ar71xx version are: * old kernel sections of code removed * 'bool swap_dma' provided by platform data is now set by boolean DT property 'qca,nand-swap-dma' * board-supplied (mach-*.c code) platform data removed - its elements become either unused, redundant or replaced by DT methods (like reset) * IRQ is reserved by devm_request_irq() so free_irq() is not needed anymore * calls to deprecated nand_scan_ident() + nand_scan_tail() function pair replaced by using recommended nand_scan() with attach_chip() callback * ECC is set to hardware by default, can be overriden by standard DT 'nand-ecc-*' properties (software Hamming or BCH are other options) This driver has been successfully tested on Netgear WNDR4300 running experimental ath79 OpenWrt master branch. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl> [add reset control] Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: essedma: Fix dead lockMasafumi UTSUGI2019-10-202-4/+4
| | | | | | | | | | | | | | | | | edma_read_append_stats() gets called from two places in the driver. The first place is the kernel timer that periodically updates the statistics, so nothing gets lost due to overflows. The second one it's part of the userspace ethtool ioctl handler to provide up-to-date values. For this configuration, the use of spin_lock() is not sufficient and as per: <https://mirrors.edge.kernel.org/pub/linux/kernel/people/rusty/kernel-locking/c214.html> the locking has to be upgraded to spin_lock_bh(). Signed-off-by: Masafumi UTSUGI <mutsugi@allied-telesis.co.jp> [folded patch into 710-, rewrote message] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: Clean up GL-AR300M DTS/DTSI inclusionsJeff Kletsky2019-10-202-4/+1
| | | | | | | | | | | | Modify GL-AR300M-Lite and GL-AR300M (NOR): * Include qca9531_glinet_gl-ar300m.dtsi directly rather than qca9531_glinet_gl-ar300m-nor.dts * Remove redundant inclusion of gpio.h and input.h Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: Fix arm64 include filesHauke Mehrtens2019-10-201-0/+280
| | | | | | | | | | | | | | | | | This patch fixes the build of gdb and strace on arm64 targets with kernel 4.19. Without this patch asm/ptrace.h is including asm/sigcontext.h and this file defines some structures which are also defined in musl header file arch/aarch64/bits/signal.h. These two definitions then conflict with each other and make the build fail. This was seen locally and also by the build bot. The struct sigcontext, struct sve_context and some others were defined twice. It looks like this problem was introduced between 4.14 and 4.19 and it was fixed in 5.0. I already requested to backport this patch to kernel 4.19. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath25: split up DEVICE_TITLEMoritz Warning2019-10-191-1/+2
| | | | | | DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
* mvebu: split up DEVICE_TITLEMoritz Warning2019-10-193-27/+90
| | | | | | DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
* mediatek: split up DEVICE_TITLEMoritz Warning2019-10-192-5/+11
| | | | | | DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
* octeon: split up remaining DEVICE_TITLEMoritz Warning2019-10-191-1/+2
| | | | | | DEVICE_TITLE is split up into DEVICE_VENDOR and DEVICE_MODEL Signed-off-by: Moritz Warning <moritzwarning@web.de>
* at91: split up remaining DEVICE_TITLE definitionsMoritz Warning2019-10-191-6/+12
| | | | | | DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
* rb532: split up DEVICE_TITLEMoritz Warning2019-10-191-1/+2
| | | | | | DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT Signed-off-by: Moritz Warning <moritzwarning@web.de>
* kernel: layerscape: fix compilation errorBiwen Li2019-10-191-0/+28
| | | | | | | | | This fixes a compilation error as follows: drivers/staging/fsl_qbman/qman_config.c:815:29: error: bitwise comparison always evaluates to false [-Werror=tautological-compare] if ((qman_ip_rev & 0xFF00) == QMAN_REV31) { Signed-off-by: Biwen Li <biwen.li@nxp.com>
* ipq806x: WPQ864: fix partition unit-addressChristian Lamparter2019-10-181-1/+1
| | | | | | | This patch fixes what seems to be a simple copy & paste error with the unit-address of the BOOTCONFIG partition. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-04 03:54:06 +0000