aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* ath79: support for TP-Link EAP225 v4Sven Hauer2022-06-283-0/+71
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This model is almost identical to the EAP225 v3. Major difference is the RTL8211FS PHY Chipset. Device specifications: * SoC: QCA9563 @ 775MHz * RAM: 128MiB DDR2 * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (SoC): b/g/n, 3x3 * Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO * Ethernet (RTL8211FS): 1× 1GbE, 802.3at PoE Flashing instructions: * ssh into target device and run `cliclientd stopcs` * Upgrade with factory image via web interface Debricking: * Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC) * Bridge unpopulated resistors R225 (TXD) and R237 (RXD). Do NOT bridge R230. * Use 3.3V, 115200 baud, 8n1 * Interrupt bootloader by holding CTRL+B during boot * tftp initramfs to flash via LuCI web interface setenv ipaddr 192.168.1.1 # default, change as required setenv serverip 192.168.1.10 # default, change as required tftp 0x80800000 initramfs.bin bootelf $fileaddr MAC addresses: MAC address (as on device label) is stored in device info partition at an offset of 8 bytes. ath9k device has same address as ethernet, ath10k uses address incremented by 1. Signed-off-by: Sven Hauer <sven.hauer+github@uniku.de>
* kernel: backport RTL8211F clkout-disable patchSander Vanheule2022-06-271-0/+119
| | | | | | | | | | | | | | In Linux v5.14 an extra feature was introduced for the RTL8211F phy, allowing to disable a clock output from the phy. Part of that patch is to always (soft) reset the phy upon initialisation. This phy reset is required to have a working ethernet on the TP-Link EAP225-Outdoor v3 and EAP225 v4 after a reboot. Otherwise the ethernet port will only function properly on cold boots. Tested-by: Andre Klärner <kandre@ak-online.be> # EAP225-Outdoor v3 Tested-by: Sven Hauer <sven.hauer+github@uniku.de> # EAP225 v4 Signed-off-by: Sander Vanheule <sander@svanheule.net>
* lantiq: dts: td-w8980: Remove duplicate PCI propertiesMartin Blumenstingl2022-06-271-3/+1
| | | | | | | | | lantiq,bus-clock, interrupt-map-mask and interrupt-map are already defined with these exact values in vr9.dtsi. Drop them from vr9_tplink_tdw8980.dts to just have one place where these are maintained. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* kernel: bump 5.15 to 5.15.49Rui Salvaterra2022-06-2727-229/+168
| | | | | | | | | Deleted (upstreamed): generic/backport-5.15/702-v5.19-34-net-ethernet-mtk_eth_soc-fix-misuse-of-mem-alloc-int.patch [1] [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.49&id=fcba12a4308143f1f1dcb0face8b3ffb51edcc5c Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.15 to 5.15.47Rui Salvaterra2022-06-2726-118/+93
| | | | | | | | | | | Deleted (upstreamed): generic/backport-5.15/702-v5.19-32-net-ethernet-mtk_eth_soc-out-of-bounds-read-in-mtk_h.patch [01] [01] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.47&id=b24ca1cf846273361d5bd73a35de95a486a54b6d Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com> [Removed 702-v5.19-32-net-ethernet-mtk_eth_soc-out-of-bounds-read-in-mtk_h.patch] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 5.15 to 5.15.46Rui Salvaterra2022-06-2758-622/+92
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Deleted (upstreamed): generic/backport-5.15/400-mtdblock-warn-if-opened-on-NAND.patch [01] generic/backport-5.15/420-v5.19-01-mtd-spinand-gigadevice-fix-Quad-IO-for-GD5F1GQ5UExxG.patch [02] bcm27xx/patches-5.15/950-0029-Revert-mailbox-avoid-timer-start-from-callback.patch [03] bcm27xx/patches-5.15/950-0417-bcm2711_thermal-Don-t-clamp-temperature-at-zero.patch [04] bcm27xx/patches-5.15/950-0740-drm-vc4-hvs-Fix-frame-count-register-readout.patch [05] bcm27xx/patches-5.15/950-0755-drm-vc4-hvs-Reset-muxes-at-probe-time.patch [06] bcm27xx/patches-5.15/950-0759-drm-vc4-txp-Don-t-set-TXP_VSTART_AT_EOF.patch [07] bcm27xx/patches-5.15/950-0760-drm-vc4-txp-Force-alpha-to-be-0xff-if-it-s-disabled.patch [08] bcm53xx/patches-5.15/031-v5.17-0005-ARM-dts-BCM5301X-update-CRU-block-description.patch [09] mediatek/patches-5.15/102-mt7629-enable-arch-timer.patch [10] Manually rebased: bcm27xx/patches-5.15/950-0741-drm-vc4-hvs-Use-pointer-to-HVS-in-HVS_READ-and-HVS_W.patch [01] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=f41c9418c5898c01634675150696da290fb86796 [02] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=d5b66645305c6f3a1b2cf75cee4157b07f293309 [03] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=119f99209d8531359bcb935f252ec435f9d21b13 [04] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=c4e1280abead1552e1764684079a43e222ccd163 [05] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=08465a1889cb48ec64431e9db745b5be15399251 [06] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=0e26a6da02e63b75b629573d13966c36aa6264f0 [07] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=01c9020b2e7c85e394879f34851805179ac3d1d8 [08] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=d47f85cc0171a5d3c5bd8cbb8a98983ca3357cbd [09] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=5151f24ac937ff7eb1f078257c66e3c0f0296010 [10] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=ffea838686b82fbb2801cdfad6ba5309d15c032d Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: 5.15: x86-64: enable CONFIG_SLSRui Salvaterra2022-06-271-0/+1
| | | | | | | | Starting with GCC 12, we have the possibility of mitigating straight-line speculation vulnerabilities in x86-64 targets. Make it so. Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.10 to 5.10.125John Audia2022-06-272-2/+2
| | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.124John Audia2022-06-2734-174/+155
| | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.122John Audia2022-06-2722-59/+59
| | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.121John Audia2022-06-2734-62/+62
| | | | | | | | | | | | Manually rebased: oxnas/patches-5.10/100-oxnas-clk-plla-pllb.patch All other patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Signed-off-by: John Audia <therealgraysky@proton.me>
* realtek: cleanup LAG loggingMarkus Stockhausen2022-06-261-12/+14
| | | | | | | | Setting up DSA bond silently fails if mode is not 802.3ad. Add log message to fix it. As we are already here harmonize all logging messages in the add/delete functions. Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
* realtek: EnGenius EWS2910P: add support for SFP portsAlexandru Gagniuc2022-06-251-0/+49
| | | | | | | | | | | | | | | | | | | | | | The SFP cages 9F and 10F share the same SCL line. Currently, there isn't a good way to model this. Thus, only one SFP port can be fully supported. Cage 10F is fully supported with an I2C bus and sfp handle. Linux automatically handles enabling or disabling the TX laser. Cage 9F is only parially supported, without the sfp handle. The SDA line is hogged as an input, so that it remains high. SCL transitions sould not affect modules connected to this cage. The default value of the tx-disable line is high (active). It is exported as a gpio, but the laser is off by default. To enable the laser: echo 0 > /sys/class/gpio/sff-p9-tx-disable/value Thus, both modules can be used for networking, but only 10F will be able to detect and identify a plugged in SFP module. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
* realtek: add support for EnGenius EWS2910PAlexandru Gagniuc2022-06-252-0/+186
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for the Engenius EWS2910P PoE switch. This is an RTL8380 based switch with two SFP slots, and PoE 802.3af one every RJ-45 port. The specs say 802.3af, but the vendor firmware configures the PSE for a budget of 31W, indicating 802.3at support. Specifications: --------------- * SoC: Realtek RTL8380M * Flash: 32 MiB SPI flash Macronix MX25L25635E * RAM: 256 MiB (As reported by bootloader) * Ethernet: 16x 10/100/1000 Mbps with PoE 2x SFP slots * Buttons: 1 "Reset" button on front panel 1 "LED mode: button on front panel 1 "On/Off" Toggle switch on the back * Power: 48V-54V DC barrel jack * UART: 1 serial header (JP1) with populated 2.54mm pitch header Labeled GRTV for ground, rx, tx, and 3.3V respectively * PoE: 1 STM ST32F100 microcontroller 2 BCM59111 PSE chips Works: ------ - (8) RJ-45 ethernet ports - Switch functions - LEDs and buttons Not yet enabled: ---------------- - SFP ports (will be enabled in a subsequent change) - Power-over-Ethernet (requires realtek-poe package) Install via web interface: ------------------------- The factory firmware will accept and flash the initramfs image. It is recommended to flash to "Partition 0". Flashing to "Partition 1" is not supported at this point. The factory web GUI will show the following warning: " Warning: The firmware version is v0.00.00-c0.0.00 The firmware image you are uploading is older than the current firmware of the switch. The device will reset back to default settings. Are you sure you want to proceed?" This is expected when flashing OpenWrt. After the initramfs image boots, flash the -sysupgrade using either the commandline or LuCI. Install via serial console/tftp: -------------------------------- The u-boot firmware will not stop the boot, regardless of which key is pressed. To access the u-boot console, ground out the CLK (pin 16) of the ROM (U22) when u-boot is reading the linux image. If timed correctly, the image CRC will fail, and u-boot will drop to a shell: > rtk network on > setenv ipaddr <address of tftp server> > tftp $(freemem) <name-of-initramfs-image.bin> > bootm Then flash the -sysupgrade using either the commandline or luci. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> [gpio-led node names, OpenWrt and LuCI capitalization in commit message] Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ramips: add support for Asus RT-N12+ B1 and RT-N300 B1Semih Baskan2022-06-251-0/+6
| | | | | | | | | | | | | | Asus RT-N12+ B1 and Asus RT-N300 B1 are the same device with a different name. The OEM firmwares have the same MD5 with Asus RT-N11P B1. Same instructions for Asus RT-N11P B1 see: commit c3dc52e39ac8 ("ramips: add support for Asus RT-N10P V3 / RT-N11P B1 / RT-N12 VP B1") Signed-off-by: Semih Baskan <strstgs@gmail.com> (Added id from the PR review to commit message) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: add support for ASUS RT-AX53UChuncheng Chen2022-06-253-0/+182
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - Device: ASUS RT-AX53U - SoC: MT7621AT - Flash: 128MB - RAM: 256MB - Switch: 1 WAN, 3 LAN (10/100/1000 Mbps) - WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G - Ports: USB 3.0 - LEDs: 1x POWER (blue, configurable) 3x LAN (blue, configurable) 1x WAN (blue, configurable) 1x USB (blue, not configurable) 1x 2.4G (blue, not configurable) 1x 5G (blue, not configurable) Flash by U-Boot TFTP method: - Configure your PC with IP 192.168.1.2 - Set up TFTP server and put the factory.bin image on your PC - Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key Select "2. Upgrade firmware" Press enter when show "Run firmware after upgrading? (Y/n):" Select 0 for TFTP method Input U-Boot's IP address: 192.168.1.1 Input TFTP server's IP address: 192.168.1.2 Input IP netmask: 255.255.255.0 Input file name: openwrt-ramips-mt7621-asus_rt-ax53u-squashfs-factory.bin - Restart AP aftre see the log "Firmware upgrade completed!" Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com> (replaced led label, added key-* prefix to buttons, added note about BBT) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: WNDAP660: fix ethernet port orderingChristian Lamparter2022-06-254-13/+13
| | | | | | | | | | | | | | | | | | Tim Small reported: | Viewing the 'Network' -> 'Switch' config page in LuCI: | | The LuCI LAN 1 port corresponds to the port physically | labelled 2 at the rear of the device. | [...] | | When a patch cord is attached to the port labelled 1 [...], | the LED labelled 2 illuminates. [...] => Ports, LuCI and LEDs are reversed/don't match. Reported-by: Tim Small Fixes: #10111 Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* x86: fix damaged config 5.10 refreshChristian Lamparter2022-06-243-5/+3
| | | | | | | | | | | | Restore CONFIG_I8K + CONFIG_INTEL_INT0002_VGPIO that got removed when I refreshed the config. Each x86 target gets its own CONFIG_CRYPTO_BLAKE2S + LIB settings as only the x86_64 can use the accelerated x86 version. Also remove two extra spaces that sneaked into geode's config. Fixes: 539e60539a2f ("generic: enable CRYPTO_LIB_BLAKE2S[_X86|_ARM]") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* octeon: add support for Ubiquiti UniFi Security GatewayClemens Hopfer2022-06-248-6/+211
| | | | | | | | | | | | | | | | | | | Ubiquiti UniFi Security Gateway (USG) is largely identical to the EdgeRouter Lite (ERLite-3) apart from a different board ID and two dome leds. Device data (from WikiDev): CPU: Cavium Octeon Plus CN5020 @500MHz 2-cores Ethernet: 3x Atheros AR8035-A GbE PHY's Flash: On-board 4MB Flash Storage: Internal 3.8GB USB Flash (Kingston ID) drive w/ 1.5GB free for use occupies single internal USB port. Serial: 1x RJ45 port on front panel. 115200, 8N1 Buttons: 1x Reset Flash instructions are identical to EdgeRouter Lite. Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
* ath79: fix rootfs padding for D-Link DAP-2xxxSebastian Schaper2022-06-241-1/+2
| | | | | | | | | | | It was observed that `rootfs_data` was sometimes not correctly erased after performing sysupgrade, resulting in previous settings to prevail. Add call to `wrgg-pad-rootfs` in sysupgrade image recipe to ensure any previous jffs2 will be wiped, consistent with DAP-2610 from the ipq40xx target, which introduced the double-flashing procedure for these devices. Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
* generic: enable CRYPTO_LIB_BLAKE2S[_X86|_ARM]Tomasz Maciej Nowak2022-06-2489-2/+175
| | | | | | | | | | | | This is now built-in, enable so it won't propagate on target configs. Link: https://lkml.org/lkml/2022/1/3/168 Fixes: 79e7a2552e89 ("kernel: bump 5.15 to 5.15.44") Fixes: 0ca93670693b ("kernel: bump 5.10 to 5.10.119") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> (Link to Kernel's commit taht made it built-in, CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: bsap18x0: specify FIS directory location in dtsTomasz Maciej Nowak2022-06-244-90/+1
| | | | | | | | | The redboot-fis parser has option to specify the location of FIS directory, use that, instead of patching the parser to scan for it, and specifying location in kernel config. Tested-by: Brian Gonyer <bgonyer@gmail.com> Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* treewide: use upstream compatible for RedBoot FIS parserTomasz Maciej Nowak2022-06-245-48/+4
| | | | | | No reason to keep that around, since upstream one does the same. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* ath79: bsap18x0: pad rootfs imageTomasz Maciej Nowak2022-06-241-1/+1
| | | | | | | | | | This image is supposed to be written with help of bootloader to the flash, but as it stands, it's not aligned to block size and RedBoot will happily create non-aligned partition size in FIS directory. This could lead to kernel to mark the partition as read-only, therefore pad the image to block erase size boundary. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* ath79: ja76pf2: use nvmem cells to specify MAC addressesTomasz Maciej Nowak2022-06-242-4/+15
| | | | | | | | | | | | The bootloader on this board hid the partition containig MAC addresses and prevented adding this space to FIS directory, therefore those had to be stored in RedBoot configuration as aliases to be able to assigne them to proper interfaces. Now that fixed partition size are used instead of redboot-fis parser, the partition containig MAC addresses could be specified, and with marking it as nvmem cell, we can assign them without userspace involvement. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* ath79: move image check for devices with RedBootTomasz Maciej Nowak2022-06-242-31/+46
| | | | | | | | | | Don't comence the switch to RAMFS when the image format is wrong. This led to rebooting the device, which could lead to false impression that upgrade succeded. Being here, factor out the code responsible for upgrading RedBoot devices to separate file. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* ath79: switch some RedBoot based devices to OKLI loaderTomasz Maciej Nowak2022-06-248-38/+120
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | After the kernel has switched version to 5.10, JA76PF2 and RouterStations lost the capability to sysupgrade the OpenWrt version. The cause is the lack of porting the patches responsible for partial flash erase block writing and these boards FIS directory and RedBoot config partitions share the same erase block. Because of that the FIS directory can't be updated to accommodate kernel/rootfs partition size changes. This could be remedied by bootloader update, but it is very intrusive and could potentially lead to non-trivial recovery procedure, if something went wrong. The less difficult option is to use OpenWrt kernel loader, which will let us use static partition sizes and employ mtd splitter to dynamically adjust kernel and rootfs partition sizes. On sysupgrade from ath79 19.07 or 21.02 image, which still let to modify FIS directory, the loader will be written to kernel partition, while the kernel+rootfs to rootfs partition. The caveats are: * image format changes, no possible upgrade from ar71xx target images * downgrade to any older OpenWrt version will require TFTP recovery or usage of bootloader command line interface To downgrade to 19.07 or 21.02, or to upgrade if one is already on OpenWrt with kernel 5.10, for RouterStations use TFTP recovery procedure. For JA76PF2 use instructions from this commit message: commit 0cc87b3bacee ("ath79: image: disable sysupgrade images for routerstations and ja76pf2"), replacing kernel image with loader (loader.bin suffix) and rootfs image with firmware (firmware.bin suffix). Fixes: b10d6044599d ("kernel: add linux 5.10 support") Fixes: 15aa53d7ee65 ("ath79: switch to Kernel 5.10") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> (mkubntimage was moved to generic-ubnt.mk) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: jj76pf2: enable TCN75 sensorTomasz Maciej Nowak2022-06-242-1/+14
| | | | | | | | This SBC has Microchip TCN75 sensor, wich measures ambient temperature. Specify it in dts to allow readout by applications using kernel hwmon API. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* omap: enable 5.15 as testing kernelAlexey Smirnov2022-06-241-0/+1
| | | | | | Compiled for and run-tested on BBB Signed-off-by: Alexey Smirnov <s.alexey@gmail.com>
* omap: update config for 5.15Alexey Smirnov2022-06-241-22/+17
| | | | | | This was done by executing make kernel_oldconfig Signed-off-by: Alexey Smirnov <s.alexey@gmail.com>
* omap: copy config from 5.10 to 5.15Alexey Smirnov2022-06-241-0/+680
| | | | | | copy config from 5.10 to 5.15 Signed-off-by: Alexey Smirnov <s.alexey@gmail.com>
* kernel: add kmod-leds-turris-omniaStefan Kalscheuer2022-06-242-1/+17
| | | | | | | | | | | | | | Add support for LEDs of the CZ.NIC Turris Omnia using the upstream driver. There is no generic way to control the LEDs in UCI manner, however the kernel module is the first step to actually use the RGB LEDs in custom logic. Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de> (removed DMARC notice, added driver to Turris Omnia, moved module recipe to target/linux/mvebu/modules.mk) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: force ZyXEL NR7101 to boot from "Kernel" partitionBjørn Mork2022-06-241-0/+1
| | | | | | | | | | | | | | | | | | | Make sure BootingFlag points to the system partition we install to. The BootingFlag variable selects which system partition the system boots from (0 => "Kernel", 1 => "Kernel2"). OpenWrt does not yet have device specific support for this dual image scheme, and can therefore only boot from "Kernel". This has not been an issue until now, since all known OEM firmware versions have ignored "Kernel2" - leaving the BootingFlag fixed at 0. But the newest OEM firmware has a new upgrade procedure, installing to the "inactive" system partition and setting BootingFlag accordingly. This workaround is needed until the dual image scheme is fully supported. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* ramips: mt7621-dts: fix claiming rgmii2 pin group for EdgeRouter X SFPArınç ÜNAL2022-06-242-5/+7
| | | | | | | | | | | | | | | | | | | For a TX->TX connected external phy to transmit/receive data, the rgmii2 pin group needs to be claimed with gpio function, at least for EdgeRouter X SFP. We already claim the pin group under the pinctrl node with gpio function on the gpio node on mt7621_ubnt_edgerouter-x.dtsi. However, we should claim a pin group under its consumer node. It's the ethernet node in this case, which we already claim the rgmii2 pin group under it on mt7621.dtsi. Therefore, set the function as gpio on the rgmii2 node for EdgeRouter X SFP and get rid of claiming the rgmii2 pin group under the pinctrl node. With this change, we also get to remove a definition from mt7621_ubnt_edgerouter-x.dtsi which is specific to EdgeRouter X SFP. This change is tested on an EdgeRouter X SFP. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* bcm53xx: copy patch disabling GRO to kernel 5.15Rafał Miłecki2022-06-241-0/+36
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: enable & setup packet steeringRafał Miłecki2022-06-242-0/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Packet steering can improve NAT masquarade performance on Northstar by 40-50%. It makes reaching 940-942 Mb/s possible on BCM4708 (and obviously BCM47094 too). Add scripts setting up the most optimal Northstar setup. Below are testing results for running iperf TCP traffic from LAN to WAN. They were used to pick up golden values. ┌──────────┬──────────┬────────────────────┬────────────────────┐ │ eth0 │ br-lan │ flow_offloading=0 │ flow_offloading=1 │ │ │ ├─────────┬──────────┼─────────┬──────────┤ │ rps_cpus │ rps_cpus │ BCM4708 │ BCM47094 │ BCM4708 │ BCM47094 │ ├──────────┼──────────┼─────────┼──────────┼─────────┼──────────┤ │ 0 │ 0 │ 387 │ 671 │ 707 │ 941 │ │ 0 │ 1 │ 343 │ 576 │ 705 │ 941 │ │ 0 │ 2 │ ✓ 574 │ ✓ 941 │ 704 │ 940 │ │ 1 │ 0 │ 320 │ 549 │ 561 │ 941 │ │ 1 │ 1 │ 327 │ 551 │ 553 │ 941 │ │ 1 │ 2 │ 523 │ ✓ 940 │ 559 │ 940 │ │ 2 │ 0 │ 383 │ 652 │ ✓ 940 │ 941 │ │ 2 │ 1 │ 448 │ 754 │ ✓ 942 │ 941 │ │ 2 │ 2 │ 404 │ 655 │ ✓ 941 │ 941 │ └──────────┴──────────┴─────────┴──────────┴─────────┴──────────┘ Above tests were performed with all eth0 interrupts handled by CPU0. Setting "echo 2 > /proc/irq/38/smp_affinity" was tested on BCM4708 but it didn't increased speeds (just required different steering): ┌──────────┬──────────┬───────────┐ │ eth0 │ br-lan │ flow_offl │ │ rx-0 │ rx-0 │ oading=0 │ │ rps_cpus │ rps_cpus │ BCM4708 │ ├──────────┼──────────┼───────────┤ │ 0 │ 0 │ 384 │ │ 0 │ 1 │ ✓ 574 │ │ 0 │ 2 │ 348 │ │ 1 │ 0 │ 383 │ │ 1 │ 1 │ 412 │ │ 1 │ 2 │ 448 │ │ 2 │ 0 │ 321 │ │ 2 │ 1 │ 520 │ │ 2 │ 2 │ 327 │ └──────────┴──────────┴───────────┘ Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: disable GRO by default at kernel levelRafał Miłecki2022-06-241-0/+36
| | | | | | | | | | This improves NAT masquarade network performance. An alternative to kernel change would be runtime setup but that requires ethtool and identifying relevant network interface and all related switch ports interfaces. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* realtek: fix gcc-12 build with -Werror=array-compareBjørn Mork2022-06-221-1/+1
| | | | | | | | | Removing this gcc-12 error: arch/mips/rtl838x/setup.c:64:30: error: comparison between two arrays [-Werror=array-compare] 64 | else if (__dtb_start != __dtb_end) Signed-off-by: Bjørn Mork <bjorn@mork.no>
* realtek: make "u-boot-env" partition writable for Netgear 3xx seriesAndreas Böhler2022-06-221-1/+0
| | | | | | | | | The Netgear GS3xx devices do not properly initialise the port LEDs during startup unless the boot command in U-Boot is changed. Making the U-Boot env partition writable allows this modification to be done from within OpenWrt by calling "fw_setenv bootcmd rtk network on\; boota". Signed-off-by: Andreas Böhler <dev@aboehler.at>
* realtek: make Netgear GS1xx u-boot env partition writableStijn Segers2022-06-221-1/+0
| | | | | | | | | | | Make the u-boot environment partition for the NETGEAR GS108T v3 and GS110TPP writable (they share a DTS), so the values can be manipulated from userspace. See https://forum.openwrt.org/t/57875/1567 for a real world example. Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* ath79: support for TP-Link EAP225-Outdoor v3Paul Maruhn2022-06-223-0/+71
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This model is almost identical to the EAP225-Outdoor v1. Major difference is the RTL8211FS PHY Chipset. Device specifications: * SoC: QCA9563 @ 775MHz * Memory: 128MiB DDR2 * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (SoC): b/g/n 2x2 * Wireless 5GHz (QCA9886): a/n/ac 2x2 MU-MIMO * Ethernet (RTL8211FS): 1× 1GbE, PoE Flashing instructions: * ssh into target device with recent (>= v1.6.0) firmware * run `cliclientd stopcs` on target device * upload factory image via web interface Debricking: To recover the device, you need access to the serial port. This requires fine soldering to test points, or the use of probe pins. * Open the case and solder wires to the test points: RXD, TXD and TPGND4 * Use a 3.3V UART, 115200 baud, 8n1 * Interrupt bootloader by holding ctrl+B during boot * upload initramfs via built-in tftp client and perform sysupgrade setenv ipaddr 192.168.1.1 # default, change as required setenv serverip 192.168.1.10 # default, change as required tftp 0x80800000 initramfs.bin bootelf $fileaddr MAC addresses: MAC address (as on device label) is stored in device info partition at an offset of 8 bytes. ath9k device has same address as ethernet, ath10k uses address incremented by 1. From stock ifconfig: ath0 Link encap:Ethernet HWaddr D8:...:2E ath10 Link encap:Ethernet HWaddr D8:...:2F br0 Link encap:Ethernet HWaddr D8:...:2E eth0 Link encap:Ethernet HWaddr D8:...:2E Signed-off-by: Paul Maruhn <paulmaruhn@posteo.de> Co-developed-by: Philipp Rothmann <philipprothmann@posteo.de> Signed-off-by: Philipp Rothmann <philipprothmann@posteo.de> [Add pre-calibraton nvme-cells] Tested-by: Tido Klaassen <tido_ff@4gh.eu> Signed-off-by: Nick Hainke <vincent@systemli.org>
* ath79: generic: add support for Realtek PHYPhilipp Rothmann2022-06-221-0/+1
| | | | | | | Some models of the TP-Link EAP225 series use a Realtek PHY, therefore the driver is added. Signed-off-by: Philipp Rothmann <philipprothmann@posteo.de>
* bcm47xx: Fix Netgear WNR3500L v2 image formatFlorian Fainelli2022-06-201-0/+2
| | | | | | | | CFE on these devices expects to find the kernel compressed with LZMA but with no dictionnary and no loader, adjust the image generation accordingly. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* bcm47xx: Updated devices database for Netgear WNR3500L V2Florian Fainelli2022-06-202-50/+144
| | | | | | | Update the device databases to contain an entry for the Netgear WNR3500L v2 router, the same buttons and LEDs mapping as v1 is used. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* bcm47xx: Add support for brcmnand controller on BCMA busFlorian Fainelli2022-06-2010-1/+862
| | | | | | | | Back port the patches being submitted upstream in order to make the NAND controller work on BCM47187/5358. This is a prerequisite for supporting devices like the Netgear WNR3500L V2. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* kernel: drop patch adding hardcoded kernel compilation flagsRafał Miłecki2022-06-202-50/+0
| | | | | | | | | | | | | | | | | | | 1. KCFLAGS should be used for custom flags 2. Optimization flags are arch / SoC specific 3. -fno-reorder-blocks may *worsen* network performace on some SoCs 4. Usage of flags was *reversed* since 5.4 and noone reported that If we really need custom flags then CONFIG_KERNEL_CFLAGS should get default value adjusted properly (per target). Ref: 4e0c54bc5bc8 ("kernel: add support for kernel 5.4") Link: http://lists.openwrt.org/pipermail/openwrt-devel/2022-June/038853.html Link: https://patchwork.ozlabs.org/project/openwrt/patch/20190409093046.13401-1-zajec5@gmail.com/ Cc: Felix Fietkau <nbd@nbd.name> Cc: Hauke Mehrtens <hauke@hauke-m.de> Cc: Rui Salvaterra <rsalvaterra@gmail.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
* lantiq: dts: fix reset controller reference on Danube and AR9Martin Blumenstingl2022-06-202-2/+2
| | | | | | | | | | | ar9.dtsi and danube.dtsi only have one reset controller and they are naming it "reset". This is equivalent to "reset0" in vr9.dtsi. Fix the references to the reset controller in the recently added PCI controller reset line. Fixes: 087f2cba26faf0 ("lantiq: dts: Add the reset line for the PCI controller") Reported-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* ramips: fix booting on ZyXEL NBG-419N v2Piotr Dymacz2022-06-201-0/+1
| | | | | | | | | | | | | This fixes a well known "LZMA ERROR 1" error, reported previously on numerous of other devices from 'ramips' target. Fixes: #9842 Fixes: #8964 Reported-by: Juergen Hench <jurgen.hench@gmail.com> Tested-by: Juergen Hench <jurgen.hench@gmail.com> Signed-off-by: Demetris Ierokipides <ierokipides.dem@gmail.com> Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* kernel: use KCFLAGS for passing EXTRA_OPTIMIZATION flagsRafał Miłecki2022-06-192-18/+6
| | | | | | | This uses kernel's generic variable and doesn't require patching it with a custom Makefile change. It's expected *not* to change any behaviour. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: backport mtd parser for Sercomm partitionsRafał Miłecki2022-06-197-16/+621
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-03 17:53:19 +0000